I have dlink dir-600 router and I want to block access to website [ URL] for only one PC connect to router. i can either block web access to both PCS connected or block entire web access to one PC.
View 1 RepliesI found an interesting manual at this forum for blocking websites whits local content filtering. After I've modified the variables to get more details, I stopped at on question. My current Problem is "zone-pair.
zone security Z-SECRUTIY-SOURCE
zone security Z-SECRUTIY-DESTINATION
zone-pair security ZP-SECURITY source Z-SECRUTIY-SOURCE destination Z-SECRUTIY-DESTINATION
service-policy type inspect CM-INSPECT-TRAFFIC
[code]...
Region : India
Model : TL-WR740N
Hardware Version : Not Clear
ISP : BSNL BB
I have a BSNL BB connection. When I use the connection directly, without adding TP Link router, all the websites open flawlessly. Once when I connect the wireless router, certain websites for example Yahoomail, pepperfry.com, yepme.com don't open at all. These are just examples, but I'm unable to access many sites which is a bit annoying. But sites such as gmail, youtube, facebook open clean, there are no issues. I didn't make any configuration changes too. I tried it more than three or four times, but there is a restricted access only.
I tried to find an answer to my issue however came up short. Did find,url... but that for a 600 not 601. I have "Mac filtering on and to only ALLOW the addresses below" however, it allows any computer, even if i do not have them listed.
View 3 Replies View RelatedI have come across articles mentioning that URL Filtering can be implemented by using ASA 5505 with URL Filtering Servers. But Websense and other Web Filtering Servers are paid ones ? Are there any free solutions available ? What exactly is N2H2 ? The reason is I don 't want to increase the CPU utilization of ASA by implementing URL filtering within the device. If I have around 30 nodes which connects to the internet via a 2Mbps line through ASA 5505 and if I want to block around say 10 or 15 URLs , will it increase CU utilization beyond permissible limits ? Currently the CPU Utilization is around 10 - 15 . Here's the infrastructure setup .
------------------------------------------------------------
Nodes -->Switches-->ASA 5505-->Internet
-------------------------------------------------------------
My network is set up in the following way..
DSL-320B | Linksys E3000 192.168.0.0/24 Subnet A Static Route 192.168.1.0 255.255.255.0 192.168.0.100 | Wan Port 192.168.0.100 DIR-655 | DIR-655 192.168.1.0/24 Subnet B
I am unable to browse by IP any machines on Subnet B from Subnet A and suspect this is due to the NAT and the Endpoint filtering within the DIR-655.
It seems (and should be) pretty straight forward; under ADVANCED go to WEBSITE FILTERING and enter in the URI, or partial URI, that you want blocked and make sure the drop-down menu is "DENY computer access to ONLY these websites". The only problem is, I can still get to all of them. I saw in another forum that you had to check "Enable Access Control" and go through a 6-step process where you specify machines - I truly hope that isn't the solution, because it's needlessly complicated for most users who only want to block ALL devices on their network from accessing certain sites. My Hardware Version is B1 and my Firmware version is 2.00NA.
View 2 Replies View RelatedWhere on my router interface I could go to enable both the SPI Firewall, and the Wireless MAC Filtering? I have the D-link DIR-815.
View 1 Replies View RelatedDIR600 doesn't allow me to enable wireless MAC filtering when I setup DIR600 as access point. (I connected DIR600 (access point) to my another room's router.)
View 1 Replies View RelatedI would like to know how to configure my DIR-600s firewall UDP Endpoint Filtering. I ve read some guides and I ve got to configure this to Endpoint Independent in order to play League of Legends. The problem is that I can see the option Firewall & DMZ but then I don't see the UDP or TCP Endpoint Filtering options.
View 1 Replies View RelatedI have had a great experience with my old DIR-655 (rev A) router. However, I would like to upgrade to a newer and better D-link router for my home that contains many well-connected children. Which routers are like my DIR-655, and have better overall performance than the DIR-655 without necessarily using the benefit of the 5 GHz second band. What better performing routers can record more than 24 MAC addresses in the Network Filtering area? I understand many people don't agree with MAC address filtering, but I like it to keep my kids from giving out my network password to all the neighbor kids and their friends too. So, MAC address filtering works for me. Or, should I just get an updated version of the DIR-655?
View 5 Replies View RelatedMy DIR-655:
Hardware Version: A4
Product Page: DIR-655
The problem is that Website Filer doesn't work if on STEP 3: SELECT MACHINE of Access Control the machine was selected by MAC address. When the machine was selected by IP everything is fine.The problem is that IP addresses are assigned dynamically, so how to make sure that the policy would be applied to the same machine?
I have yet another problem now with the DIR-825. I have a DAP-1522 that I connect my multimedia devices to like my TV, BD player, etc.
For added security, I use MAC filtering to only allow access to my devices that connect to my router. However, after several hours, the devices connected to my DAP-1522 can no longer connect and neither can I connect to them. The odd thing is that I can connect just fine to the 1522 itself. I NEVER had this issue with the DIR-655 so I figured it had to be the 825. After trying several things, I essentially narrowed it down to the MAC filtering.
If I turn MAC filtering off everything works fine all the time. If I turn it on, everything works fine for several hours, even up to a whole day, but then eventually my devices can no longer see or be seen.
All 3 previous wireless routers I've had were all LinkSys routers and I had to overcome a learning curve since configuring this DIR-655 is slightly different..What I want to do is allow only the WiFi MAC addresses that I choose to access the network. It seems to me that in order to accomplish this I have to include all of my wired LAN devices' MAC filters as well. I can see having MAC filtering for WiFi devices, however why do I need to add my wired LAN devices MAC addresses? I'm not going to allow just anyone to walk into my home off the street and plug a computer into the network via CAT-5 ethernet cable, so isn't there a way to accomplish just the WiFi allow list and the heck with the wired nodes? The LinkSys routers I used in the past allowed me to allow the MAC filter for WiFi devices only. Is there a way around having to allow all MAC's and just allowing the wifi's?
View 5 Replies View Related207.NA Firmware, B1 Hardware in use on a DIR-655, Time Warner Cable setup. Nothing to do with Revision, cordless phones,I saw this asked once before specifically here, but it was never answered.After several attacks via our cable network and neighbors, we've HAD to turn on MAC filtering. There are TONS of devices attached normally so two situations popped up:
#1: What happens when you max out the authorized MAC address listings? Does the page get longer when you save/reboot it? Do I have to do it manually from there forward and where can I get down to the core programming level to edit the code and put the MAC's that are around and on 100% of the time to open up the plug-in list on the GUI?
#2: Guest Zone - we NEED a way to have random guests get on our Network with a different password we can randomly change to prevent the outside abuse, etc. but am I understanding what little else has been posted that the MAC filtering also covers the Guest Zone and therefore I have to stick them in there before they could simply log on with the current password? Is there any way to change/stop that without eliminating MAC filtration as a whole?
It shows this option "Filter wireless clients: Apply MAC Filtering to devices that connect to the network via Wi-Fi. This is the normal usage of MAC Filtering. Filter wired clients: "However I don't see that option on the actual page. How can i enable Mac address filtering only for the wireless side?
View 7 Replies View RelatedWhen I connect through my router, GMail, Livejournal, Yahoo and Facebook and some other sites are really slow, especially Google and Livejournal. If I connect directly to the modem, they are fine. I've reset the modem to factory and it's still slow on both my Vista PC connected with a cable and my GF's Macbook on wifi. I clear the cookies regularly, use CCleaner, scanned for adware, viruses. What do I do?
View 14 Replies View RelatedI can't block web sites on my DIR655
View 3 Replies View RelatedTwo weeks ago my DIR-825 stopped connecting to some URLs. I made no changes to the router nor did I add any new software. If I tether my laptop to my smartphone, I connect to those URLs without any problems. I connected my cable modem directly to the laptop and I was able to connect to the URLs also.
View 7 Replies View RelatedI'm unable to open a few websites through the DIR-825. I can connect the PC to the ISP modem and these sites open just fine. It's not a browser problem.
I've updated to the very latest firmware and still have the problem. I've also researched this issue and can't seem to find a work-around for this issue.
I have a Cisco RV082 that doesn't appear to filter any selected categories. To run through what i've done so far, within the 'Web Protection' screen i've: enabled URL filteringconfigured a number of categories to filter by putting a tick in the repective business hours boxset the business days to 7 days a weekspecified business time as 24hrshit the save button.
My licence appears as activated and my platform shows as "gateway service".I've gone on to a number of machines and all are able to access websites that fall under my blocked category (facebook for example even though i've blocked the social networking category).
Over the past few months I've noticed that, although my USB adapter picks up a good signal from the router (never less than 65 - 70% signal strength) and stays connected to it I am at times unable to access any websites. It started off happening once or twice a week and could happen for about 5 - 10 minutes at a time but now happens several times a day and can stop me accessing the web even though the USB adapter says that it is still picking up the signal from the router. After a period of time it will just start working again, I don't have to restart the router or anything.I've tried changing the channel to a few different ones after using a utility to see what my neighbours were using but this hasn't made a difference. I'm using a Netgear RangeMax Dual Band Wireless-N USB Adapter. It has the N technology so should work pretty well.The current firmware version is 1.00VG dated 5th May 2009. In the router settings it allows you to search for an update for the firmware however it told me that my current version is the most up to date.
View 7 Replies View RelatedOn my server I host several websites.Last Monday we got our FttH-connection and I'd set up my D-Link DIR 655 to manage our server and other computers.In the webconfig of my router I set up the Virtual Server for several applications (Telnet - 23, HTTP - 80, HTTPS - 443, FTP - 21, SMTP - 25, POP3 - 110, IMAP - 143 and also ports 20, 22 en 81) redirected to my server's IP address.For these items the private port and the public port of each item is the same port number; the protocol is TCP for these items. I didn't change the options Schedule ("Always") and Inbound Filter ("Allow All").
The DNS of my domains (samendienen.nl and some other domains) is set to my new IP-address.May be I forgot some other settings in my D-Link-router.what I have to do to make my websites reachable?
I have 4 computers using the DIR-615. One of them works just fine (windows 7) the other ones (XP sp3) are very slow, one of which is on the wireless the others are plugged in.
View 3 Replies View RelatedI got a new DIR-655 RevB today, and set it all up. It works fine right now in terms of speed, but certain websites (specifically, facebook.com) load very slowly on wireless. I've tried on two computers with different browsers / operating systems and it still loads slow. I also have comcast which I use a linksys router with, and it loads instantly. Connecting through wired works. Also, I get no slow down when connecting wirelessly if I use a VPN. When I do a speed test, I get my full speed, so that's not a problem.
A few things I have tried:
-Changing the wireless channel
-Disabling QoS
-Disabling traffic shaping
-Changing DNS servers
-Transmit only N/G
-Reducing MTU size
-Disable Dynamic DNS
-Disable advanced DNS service
-Connect to facebook through SSL and not
-Turning router off and on again
Also as a side, unrelated problem, whenever I enable a few ports to be forwarded, I can't connect to the internet when either wired or wireless?
In Setup > Parental Control it is possible to set rules attached to specific website URLs. I want to block access from 1am to 6am.
However these rules only apply to websites URL. Is there a way to apply a rule to ALL websites at once? I tried to enter "*" or "*.*" in website URL field but it doesn't work.
Is there a way to block specific computers on the LAN from specific web sites by the domain name? All I can see is that if I put, for example, www.facebook.com, it will be blocked from all computers on the LAN, whereas if I want to block only 192.168.1.3 for example, I have to use the IP address through the Access Control, which is much harder and ****e to some "work around" by the user.
View 3 Replies View RelatedI'm using DIR 600 for home use. Recently, I noticed that I have trouble connecting to some websites (Twitpic.com, 4shared.com) which I never had any problems before I used the wireless router. It doesn't exactly block the websites but rather it won't load completely (i.e., with Twitpic, I can load the site but not the images; for 4shared I really can't load the page itself).Initially, I had problems updating JDownloader after installation. I tried using our old Edimax wired router, and the JDownloader update worked flawlessly. I also tried loading Twitpic while connected via LAN, and it also worked properly.I'm assuming the problem lies with the wireless router but when I set it up for use I only tinkered with the WPA/WPA2 security for a password-secured wifi connection at home, and nothing more since I can't understand the other features.
View 5 Replies View RelatedI've installed aDIR655 for my friend's cafe and found that Clients ( both wired and WIFI ) have difficulties accessing Yahoo and MSN while Googles etc ( and other Newspaper and webmail sites are OK ) is fine.....I tried to reload and reboot and re-config etc but all in vain...
View 1 Replies View RelatedI noticed that no matter what URL I put for a website using HTTPS such as Facebook [url]...
View 1 Replies View Relatedi've lost the ability to view live streaming video (adobe flash, i think) on several websites. it happened gradually over several weeks and now videos will not load. the dir-615 has functioned flawlessly over several years but it might be showing its age now. connecting directly to my com cast broadband modem fixes the problem. can i tweak the router settings or do i need to replace it?
my setup: dir-615, H/W Ver. E1, F/W Ver. 5.00NA, two wired connections to X Box's and one to Win 7 PC. wireless connections to several Win 7 laptops and other tablets/phones. com cast high speed broadband with their Norton security suite.
if replace.....i need a recommendation. the best bang for a buck while staying within a tight budget.
Like others I see on this board, we've got middle- and high-school age kids whose access to FB and other sites needs to be controlled/scheduled.
I thought the DIR-655 was great, in that it has features that, on the face of it, would seem to be ideal for blocking domains and restricting access.
My problem: I've never been able to get this to work.
I've set up schedules and created lists of domains that I want to limit access to according to the schedules, but the only constraint I've ever gotten to stick is blocking access completely to the router.
*None* of the schedule-based or website-based access controls have ever worked; I'll put the block in place to my daughter's computer's MAC address so she shouldn't be able to get to youtube or facebook, save, bounce the router, but then I go by her room and she's still busily chatting away online to her FB friends.
Based on similar posts I've seen on this forum, this may not be a unique problem.
So in a nutshell, this is what I want to do:
1) Block certain computers (identifiable by MAC address)
2) from being able to get to particular named domains (and any of their sub-domains)
3) according to a schedule that I can create and modify.
My preference would be to do this in the router, but again, responses I've seen here suggest that may not be possible.
I am using Comcast as an ISP and have a standalone Arris modem. I, obviously, have a DIR-655 router REV B with a firmware revision on 2.00NA. I have already turned off packet shaping and QOS. Also, I have set the firewall settings to Endpoint Independent for both TCP and UDP, and assigned static IP addresses to my computers. The problem I am having is that whenever I go to any secure websites, i.e. anything that starts with https, it takes an extraordinary long time to log in and to navigate to any webpages therein. I also cannot upload photos to a website and when I try the Speed-test.net website the download speed is OK but the upload test errors out, it doesn't connect.
View 2 Replies View Related