I received WAP4410N-G5 AP with 2.0.2.1 firmware and set up it very easily. Never experienced a single signal drop in a few days.
After updating firmware to 2.0.4.2 version I am completly unable to make any changes! If I press on "Enable" or "Disable" all settings will be lost after I apply them and neither "Enabled" nor "Disabled" is selected.
Had to revert back to 2.0.2.1. Is my AP faulty?
Would like to report that WAP4410N Access Point cannot disable Wi-Fi Protected Setup (WPS). Tried both firmware 2.0.2.1 (19/JUL/2010) and the latest 2.0.3.3. No Disable option in both firmware.
If you do not change the default IP or default SSID for example, The WPS is disable by default. Once you change default IP and SSID for example, the WPS is then enabled. There is no Disable Option for WPS.
Bought a month or 2 ago, configured and installed as our public access point. Worked well except for locking up weekly. A few weeks back, I lost all connectivity with it. It will get power, but no wireless and no Ethernet lights on the front. I attempted to reset it with no luck. Firmware is V01.
View 1 Replies View RelatedI just recieved a WAP4410N and managed to log in to the web interface. It is not allowing me to change many settings. I try to change the wireless network mode and click on save and it goes back to disabled again.
P.S. I have just upgraded the firmware to 2.0.3.3 and tried to set it back to the factory defaults. neither worked.
send me wireless bridge settings for WAP 4410N.
I have purchased two sets of WAP4410N and i need this to connect as wireless bridge to use our external office users(1 or Max 2) which is just beside our office building to surf our internet and retrieve data from our main server.
I ordered a pair of WAP4410N to use as a bridge for a split office. So far they have worked without a hitch but the throughput is less than stellar and I was wondering what the recommended configuration was for best performance (and how much speed could be expected in general) out of these two? [code]
The two nodes are separated by about 25 yards across a parking lot with direct LoS to the other, placed inside a window mounted on the wall -elevated at about 10' so cars in the lot outside do not block visibility. At best the throughput I've seen is 1megabyte/sec, and that seems very slow/clunky to me for the 802.11n specification. Am I missing some setting, updated firmware, or physical setup (AC power instead of PoE for better antenna output maybe?) to have such limited performance?
I have a simple wireless network that works fine, except for one room where the signal is too low. So I purchased a WAP4410N to use as a range extender. provide the exact settings that are need to set this up? I have tried many, many different configurations, and I can't get it to work properly. In particular, it will not give me an IP address and therefore won't connect. Also, is it important to use the SAME SSID name? or better to use a different name so as not to confuse the two signals (base unit vs repeater (4410)).
View 1 Replies View RelatedWe've had this AP for just over a year and just recently it started dropping its wireless connection. To fix, I have to and unplug the power and then plug it back in.. Then it works again for a few hours and drops out again. If I navigate to the config page right after it drops, all of the settings seem to be completely gone. But if I go through and unplug/plug it in again, all of the settings are back.
I updated the firmware to 2.0.4.2, but that didn't seem to resolve the problem. Is this thing a brick now?
I have an EA6500 wireless router and i have to constantly disable / enable the guest wireless access to get it working again. It might work some time less than a day but then it fails. I tried to set the wireless channel manually instead of auto and the same issue is happening. The private wireless ssid works just fine. I have the latest firmware.
View 9 Replies View RelatedJust tried to setup my wireless adapter and after it tells me to plug in my adaptor I get.Wireless adapter setup requires that wireless connections are managed by Microsoft windows.
Error Description: Other Wireless Manager
Model Name: AE1000
Operating System: WIndows Vista SP2
Software Version: 1.2.10104.2
I looked all over my computer I can not find any other wireless manager on my system nor could I find a way to enable or disable windows wireless manager.
I have the E3000 and have attched a WD 1TB USB drive. I set it up for FTP and Media sharing and it worked fine but somehow recently I could not connect anymore. I checked the router and all of my setting for the FTP and Media server were gone. The disk drive still shows avaiable but now it shows the entire 1TB free (it was at least half used). This is the second time this has happened, first I tjhought it was a bad disk and replaced it but now it happened again. I did do a power cycle some time ago but I remember it still work after that. Not sure why I am losing my settings. This does not give me a comfort level as to storing anything valuable on that drive.
View 1 Replies View RelatedI am using lms 3.2.where I have added devices manually.Because discovery settings the device are taking some random ip updating the display and hostname.
I want to disable the full discovery settings..
my internet connection is just connected to a router , it is OK to always disable and enable my internet connection? because every time i open my PC i always disable and enable the internet connection to make it work. how to make my internet connection work properly every time when i open my PC?
View 4 Replies View RelatedI want know if it's possible with a script enable disable wifi, without every time login to router.
View 1 Replies View RelatedI have ASA5505 as my main router (192.168.15.1) and it currently it also serves as DHCP server. I have a WNDR3700 (192.168.15.2) which work as an access point and it provide wireless access for wireless devices. I have few dhcp clients where i can't setup static IP, and i want to restrict them to use static IP through MAC reservation.
1. Make ASA5505 to do the MAC reservation f, which will be easy setup for me. But as per my search its not possible.
2. Disable dhcp on ASA and enable dhcp on my WNDR3700. i tired this and dhcp clients are getting IP from wndr3700, but the problem is dhcp clients gateway defaults to 192.168.15.2 (as well as dns) and therefore no internet connection.
I have WLC 4400/5508 I stumbled across this config paging disable command to stop page breaks, works great for the one session I am logged in but it do not work for other users..
View 1 Replies View RelatedI start my pc i get 2 local area connections instead of 1 and because of this my internet does not work unless i disable and enable again the network .After enabling only 1 network shows and i can connect to internet.It may be because i replaced my motherboard even tho i uninstalled the drivers?
View 1 Replies View RelatedI bought my self a WRT120N as my wireless router for my house. and not a long ago i bought the WAP4410N, for my repeater (after i ask to some people).my house were concrete wall, it have about 15-20cm thick, and we try to avoid any wired LAN. The destinaton were unreachable with only WRT120N.it's look like this (what i want for the network on my home) : [code] i already tried to setting the WAP4410 as a wireless WDS repeater, and wireless client/repeater (with and without "Allow wireless stations to associate"). both were unable to connect (limited), although i get the signal. for the IP on the WAP4410N (192.168.0.50), i used static IP [IP, Subnet and Default Gateway were fill in] within the WRT120N range (192.168.0.2 ->192.168.0.51)
- how i configure my WAP4410N as a repeater?
- is there any settings that i must set on the WRT120N, before combining the WAP4410N?
In my ongoing project i need to monitor cisco 3750-X port status (uplink/downlink) i.e. whenever there is some problem at a specific port. I need to monitor it through an OPC server and right now what i am doing is as follows: i am using Kepserver and i have added SNMP driver in it for that purpose i am not a networking expert but what i have learnt till now is that SNMP agent (that resides in switch) delivers the status of MIBs to SNMP manager ( which in my case is kepserver (opc server)) for the above purpose i am adding IF-MIB to monitor OID 1.3.6.1.2.1.2.2.1.8 (which shows port statuses) but when i add that in OPC server then it indicated that this OID is not available in the Switch ( it might be disabled) so i need to ask if there is any way to enable OID's in a switch,
View 0 Replies View RelatedI`m looking to automate some functions in a web application.Functions like enable/disable interfaces on a Cisco 3550 switch.
View 5 Replies View RelatedWhen disabling SSID broadcast and enabling MAC address filtering on WAG320N, my other wireless laptop get disconnected. And when you try to connect, it doesn't connect again.
View 3 Replies View Relatedi am using hp g62 notebook and i an unable to turn on the wifi adapter. in my hp wireless assisatant there is bluetooth option to turn on and that is also not working. i tried switching on the fn key and f12 no use. how do i enable the wifi adapter.
View 1 Replies View RelatedI have a HP 4100N printer and I am using it over network.
Previously I was able to access the printer settings over internet, but now the only thing visible is Device Info and Networking. I can connect to the web server and I can set all the network related settings, but that's not what I want.
There should be a supplies, config, print info, etc. page, what are not visible now.
what setting should I set to enable this printer config page on the webserver?
The printer is a HP 4100N and the network card is J4169A (Jetdirect 610n).
Is there a way to restore the device to factory settings. I tried the reset button with a paper clip.
View 2 Replies View RelatedI have lost the "ENABLE" password on my 3750 switch.
View 5 Replies View RelatedI had to reset and reboot. I entered the router ISP and went through the 4 step process then rebooted.
My question/problem is now the router is wide open. How do I find page where I can enable the security settings and lock down the router to the outside world?
I have the following equipment:
Cisco 871W router
2x WAP 4410N APs running 2.0.3.3
I currently have 1 AP connected to the router via copper. The AP to AP link is over 802.11. I have attached a diagram reflecting the current topology.
The AP-to-AP link will come up utilizing B/G/N mixed mode; however, the connection is basically unusable. About 30% of the traffic is dropped, while the packets that do make it have a consistently volatile latency, anywhere from 15 to 1500 ms. I have had success using G-only and B/G mixed. The link is stable (I have had the best results with B/G). The problem is, I didn't buy the 2nd 4410N to run the G protocol. I would like to connect the APs running either B/G/N (hopefully negotiating to N) or N only. I am wondering if there is a certain configuration I can utilize (perhaps using WDS repeater or bridge versus Wireless Client/Repeater?), or a firmware upgrade set for release that can make this happen for me.
Well, I sent mine back and they shafted me with a v1 unit.I don't see how you can know what the problem is and still send me a v1 unit.
I contacted SB support and they said no guarantees on getting a v2 unit.
Now I must PAY to send another unit back.With no guarantees, I don't know.
I have a WAP4410N that stopped powering on with PoE. The PoE light comes on but the Power and Ethernet light remain off. The link light comes on the port on the switch. I have tried multiple switch ports and tried a different switch.
View 3 Replies View RelatedI would like to ask for assistance on how to configure one unit WAP4410N access point to work as repeater to one unit WRT120N wireless router.
As a background, I had one WRT120N already in my house before I bought one WAP4410N as advised by a Linksys guy. I wanted to wirelessly extend the signal of my WRT120N wherever its signal is so low around my house. The WAP4410N should work as repeater to WRT120N.
I already configured WAP4410N to work as repeater by enabling all the choices in its wireless AP mode like the “wireless WDS repeater” and the “wireless client/repeater” but to no avail. I successfully setup a similar scenario before using the old pair of one WRT54G and one WAP54G. I replaced the old pair with the newer one ( WRT120N and one WAP4410N).
Is the tandem of WAP4410N and WRT120N can be configured technically as like as what I wanted? Do I need to upgrade the firmware of both devices? Did I miss something in the configuration?
I need enable WPS function on WAP4410N. This is possible with CLI command #set wps enable. But how I can connect to WAP4410N with CLI?
View 1 Replies View RelatedWe have a WAP4410N as a Access Point and a second WAP4410N as a Wireless WDS Repeater. The settings are as of below.
We couldn't get the mobile users to get connected to the Access Point. But if we uncheck the option "Allow wireless signal to be repeated by a repeater.", it works.
Router: Cisco WRVS4400N secured with WPA2WAP: Cisco WAP4410N . Router was working well but signal too weak in distant rooms. So, purchased a WAP4410N but am unsure about AP configuration. From reading the docs, I understand these to be the relevant choices:
1) Access Point -- Wired connection through built-in Ethernet port. (Not Desired)
2) Wireless WDS Repeater
3) Wireless Client / Repeater (What is difference from WDS Repeater?)
4) Wireless WDS Bridge
Desired Result:Simply extend the network. As a laptop is carried from room to room, laptop should switch to the strongest signal seamlessly, without user doing anything manually. No matter where I am, laptop should see entire network. Also, I prefer that the WAP not require a wired Ethernet connection (that is, I would like the WAP to receive/repeat the router's wireless signal No Ethernet Cable Required).
1. Which of the above 4 settings is best for achieving desired outcome?
2. What should the SSID be on the WAP? Same as on the router?
3. Should both the router and WAP be on the same channel? (I suspect not, but included docs sound like they should be..?)
4. Should both the router and the WAP have the same wireless security setting (WPA2) and pass phrase?
5. On the router, under the Wireless menu --> WDS sub menu there is a check box: "Allow wireless signal to be repeated by a repeater". I assume this must be checked?
6. I understand that Microsoft's built-in Wireless Zero Configuration service does not disambiguate APs which share the same SSID and may not always roam with the strongest signal.*** We need to move from area to area and seamlessly retain the network signal. Is this still a problem in Windows7? Is there a workaround for XP's WZC deficiencies?
Is there anything else I should know? [URL]