I am trying to enable Ftp traffic through our firewall at work. We have a Cisco 5505 ASA and we cannot access any Ftp servers outside our network. We are running 8.3(2). Any have commands I can run to allow us to connect to ftp sites?
View 6 RepliesI am currently troubleshooting a firewall policy on a ASA 5505. What command can enter in the CLI to enable live view of traffic been block and which traffic is been allow?In my experiences with other firewall vendors, other firewalls allow me to narrow down the source and destination, too. is there such thing on the ASA 5505?
View 6 Replies View RelatedI have a 2960G that I keep on the bench as a work switch. I assigned an IP address to it. The techs have had trouble imaging workstations using GHOST. Do any config changes need to be made to enable multicast to work? Everything is in VLAN1 at this point and the GHOST server is also the DHCP server.
View 1 Replies View RelatedI start my pc i get 2 local area connections instead of 1 and because of this my internet does not work unless i disable and enable again the network .After enabling only 1 network shows and i can connect to internet.It may be because i replaced my motherboard even tho i uninstalled the drivers?
View 1 Replies View RelatedWe are looking to implement traffic shaping/policing primarily for P2P traffic. As natively the ASA5550 is only capable of p2p inspection if the traffic is tunneled via port 80 is the AIP-SSM the way forward? We have 2 5550s in active/active failover config. As a side note we are also looking to implement an IDS/IPS system so could this module cover all?Is this module going to provide the desired outcome or is there another module/device out there better suited for this? I would prefer to use the ASA5550s as opposed to implementing another product if only that we can make use of the investment we already made on these devices.
View 1 Replies View RelatedI am testing limit bandwith using my ASA 8.2, i am trying to limit internet access for certains users , i order to save Bandwith for the important things but i can´t get any limitation
My configuration is the following, the acces list is just for my pc in order to test, and the service policy is applied to outside interface (called internet in my case) for incoming traffic
access-list Internet_mpc_1 extended permit ip host 172.16.127.70 any class-map Internet-class-TEST match access-list Internet_mpc_1 policy-map Internet-policy-web class Internet-class-TEST police output 1024000 1500
service-policy Internet-policy-web interface Internet
With show service policy i can´t see any activity on the policy , but if i do a similar configuration for inside interface outgoing traffic i can see packets allowed and dropped
I have an ASA 5520 with the below config
Gi0/0: outside (Internet)
Gi0/1: inside (Internal users)
Gi0/2: DMZ (web servers, ftp, Mail etc..)
I have a SMTP relay deployed on the DMZ for mailing. I have also a mail servers installed in the internal lan,
I want to allow trafic from dmz to reach internal lan, and i want normally also allow stmp relay from dmz to reach Internet.
How can i block trafic from DMZ to reach Internal Lan (instead of smtp) if the to allow trafic from dmz to internet i must put ANY in the policy?
For allowing trafic from DMZ to reach Internet, the policy must be DMZ -----> ANY ----->Services., this policy means DMZ can implicity reach Internal Lan?
I have a simple setup where I have a 2911 router with three interfaces, Inside, Outside and a second "Inside" interface which is labelled as a DMZ. The Zone Firewall applied to the "DMZ" is actually Inside (until I can work through problems). I need to be able to access a device on the DMZ via its external IP so I have designed NAT to use IP Nat Enable commands. This is now working for me fine. However, since utilising IP Nat Enable, my zone firewall now denies return TCP / UDP traffic and consequently I no longer have any internet access. Looking at the syslog messages, the reason for this is that the router is denying these return flows not because they are matching the outside-to-inside policy, but rather they are matching the outside-to-SELF policy. The router seems the detect that the internet traffic is being returned to SELF, when in reality the NAT rule should pick this up and forward it to inside. I can understand why this is happening, because I am NATting all private / inside traffic behind the external IP of the router, which is assigned to the Gi0/0 interface. [code]
View 1 Replies View Relatedif y need to enable VPN IPSec through the firewall. y just need to need to allow the port 4500?
View 2 Replies View Relatedi want to set WRVS4400N Route all traffic through, it function as same as sonicwall Route All.
View 1 Replies View RelatedI have lots of PPPoE users that get Virtual Access interfaces created upon login based on a virtual template. I need to traffic shape them. I know how to get it to work on an individual basis, because the policing within a service policy works fine. As soon as i change it to shaping it leaves things wide open.I really dont care how it gets done, I just need to be able to specify a speed to be traffic shaped and apply that to a virtual template. I need to limit speeds on the download and upload, i understand that the upload i will use the policing, but the download i need it to smooth out the flow and be traffic shaped, not policed.
Here is my Policies and classes:
***
policy-map CHILD class class-default bandwidth 1650policy-map PARENT class class-default shape average 1650000 service-policy CHILD****
Here is my Virtual Template:
****
interface Virtual-Template8 description pppoe-auth-FTTH ip unnumbered FastEthernet0/0 ip access-group subs-in-FTTH in ip mtu 1493 timeout absolute 6120 0 peer default ip address pool FTTH-POOL ppp authentication pap pppoe-auth ppp authorization pppoe-auth ppp timeout idle 84600 service-policy output PARENT
[code]....
The results i am getting is unrestrcited throughput, i am seeing about 40mb of throughput when the target is to limit to 1.65MB. As you can see from the output the PARENT class is seeing 279116 packets, but the shaper only saw 59. In all the examples i see on the internet these two numbers should be the same. Why is the shaper not acting on all the traffic crossing that class/policy?
Hardware/IOS:
Cisco IOS Software, 7200 Software (C7200-IK9SU2-M), Version 12.4(12), RELEASE SOFTWARE (fc1)
i want to set WRVS4400N Route all traffic through
it function as same as sonicwall Route All
[URL]
I have a sge2000p to install with a uc520. I have all data traffic passing ok but voice will not work. Phones to not get ip etc.
View 4 Replies View RelatedHow to enable the VPN-3DES-AES and another ASA Box.Mate's license (VPN-3DES-AES Enabled) is not compatible with my license (VPN-3DES-AES Disabled). Failover will be disabled.The license on secondary is not compatible for secondary ASA for the failover. [code]
View 2 Replies View RelatedMay I know how to configure for remote accessing ASA 5525 via ssh?I have issued the following commands
ssh 10.60.0.0 255.255.0.0 outside
ssh 10.60.0.0 255.255.0.0 dmz
ssh 10.60.0.0 255.255.0.0 inside
ssh timeout 5
but I am not able to access ASA via ssh. Do I need to add any other command
my windows is no longer connecting to the internet.i I ran a diagnostic and it said to check firewall settings for the http port(80), https prt(443) and the ftp port(21). I haven't change anything in my settings and dont know why all of sudden i hvae to check firewall settings.
View 1 Replies View RelatedI have a pair of brand new 5520s I am in the middle of commission. After carving out all the DMZs etc I needed I realized that I really neede another physical NIC, not just another VLAN off a configured nic. [code]I am running 8.3(2). How can I turn these "Not used" interfaces into useable ones?
View 2 Replies View RelatedI'm replacing a new ASA 5505 due to a corrupted flash. On the original unit, I had the ability to SSH into the device using TeraTerm with no problems. While configuring the new device, I entered commands to enable SSH into the unit.
View 5 Replies View RelatedWe would like to enable our HelpDesk and Network team the ability to connect to Laptops using our ASA 5510 VPN device using Secure VNC application. Not sure if this is possible or how to enable this option.
View 5 Replies View RelatedWe recently purchases the Cisco ASA 5505 to get familiar with it, possibly buying more appliances for our branch offices. However, since the appliance is installed, our SIP telephones no longer register with our SIP service provider.
The SIP phones are all on 10.0.1.0/24 while the SIP provider is external via the outside network. I copied our configuration below. how to enable SIP for all 10.0.1.0/24 hosts and ports 5060, 5160, 5260, 5360?
gcxfw# show running-config
: Saved
:
ASA Version 8.4(3)
[Code].....
I have just erased an ASA and upgraded the firmware and then added an IP. How can I enable the ASDM as I can't get on it, here is the config:
ASA Version 8.4(3)
!
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
dns-guard
[code]....
I was asked to enable netflow in an ASA Firewall for Orion/Solarwinds server monitoration. Firewall is a 5550, with 4G RAM, and no extra modules but SSM-4GE. This firewall has 5 DMZ segments and ans specific segment for internet traffic.There are segments as unique subinterfaces in physical interfaces. Other segments as individual subinterfaces in the same physical interface (but individual VLANs)Usually firewall CPU flows between 30% to 40%. Rarely to 50%.
1 - How dangerous or risky could be implement netflow in this firewall?...This firewall is very critical for the customer. My concern is regrading CPU, traffic generated, memory, etc
2 - In a month, firewall will be migrated from 8.2 software version to 8.4 software version. Is there any incompatibility in some commands?...Would be recommended to perform netflow configuration after software upgrade?
3 - How could it be implemented for Orion monitoring, regarding each individual sub-interface (and so, each VLAN assigned)?I there any recommendation regarding configuration, best practices?
how do i enable port forwarding on the CLI for ASA 5510. outside subnet is 192.168.1.0/27. when i try to ping another IP with that range i can't access.
View 37 Replies View RelatedI am trying to enable access to use RealVNC on our Cisco ASA 5505 without using VPN. RealVNC uses port 5900. Users should be able to vnc to 99.23.119.78 and reach our internal server 192.168.1.4. So far they are receiving connection refused.
View 5 Replies View RelatedI've done this in the past for specific host entries with no problem, but I can't figure out how to do this for an entire subnet. I need something along the lines of the following:
access-list OKC2DAL extended permit ip 192.168.1.0 255.255.255.0 192.168.107.0 255.255.255.0
static (inside,outside) 192.168.99.0 access-list OKC2DAL netmask 255.255.255.0
I see netmask as an option, but the ASA states "invalid option netmask." The ASA is running 8.2(2). OKC-PIX(config)# static (inside,outside) 192.168.99.0 access-l OKC2DAL ?
configure mode commands/options:
<0-65535> The maximum number of simultaneous tcp connections the local IP
hosts are to allow, default is 0 which means unlimited
connections. Idle connections are closed after the time
specified by the timeout conn command
[code].....
I have a problem with an ASA5510 (8.0.4) firewall in South Africa (I'm in the UK).It's a replacement firewall that I am trying to configure remotely through a serial device with an internet facing connection, but the enable password is not working.I can connect to the device OK, type 'en' and when propted for the password whatever I use (blank, cisco, Cisco etc.) I get an 'invalid password' message.
View 2 Replies View RelatedI have configured dhcpd in an ASA 5505 and every thing is working. I am testing it to give me a warning when the address pool is about to be finished or it is empty. But don't konw how to do it. if I run the "debug dhcpd packet", i get that the address pool is empty.
View 3 Replies View RelatedWhat is Anti Spoofing in ASA 5505. Can I enable it on ASA 5505. If yes , port will be inside or Outside. ? or both ?
View 1 Replies View RelatedI get the following message when appling "DHCPD ENABLE INSIDE"
DHCP: Interface 'INSIDE' is currently configured as CLIENT and cannot be changed to a SERVER by a SERVER feature
This is an ASA 5505 Running 8.2.
how to enable inspect http on ASA 5510, so that URL information populate in the syslogs?
View 2 Replies View RelatedWe are runing PIX 535 with software version 8.02. In ASDM, I see anti-spoofing is diable in all interfaces. If I enable it, is there any negative effect? Can I enable it in DMZ, inside, and outside interfaces?
View 2 Replies View Relatedmy 1841 router can't resolve dns after enable ios firewall, I try to ping google.com from router's console fail, but dns resolution is fine from lan side.
my partial config---------------------------------
!
ip name-server 8.8.8.8
[Code].....
We are using the newest release of AD Agent (1.0.0.32.1, built 598). The ASA Firewalls 5520 are having the software release 8.4(3)8 installed.When somebody tries to connect thru the Identity based firewalls from a citrix published desktop environment (PDI) the connection is not possible. Checking the ip-of-user mapping on the firewalls (show user-identity ip-of-user USERNAME) mostly doesn't show the mapping of the USERNAME and the PDI the user is logged in. The user-of-ip mapping of the PDIs IP-address shows mostly other users, which then are used to authenticate the acces thru the firewalls.
What is interesting, that on the AD Agent using "adacfg.exe cache list | find /i "USERNAME"" i can't see the PDIs IP-address neither because it is mapped to another user.Is Citrix Published Desktop environment supported to connect thru Identity based Firewalls? How AD Agent, Domain Controllers and Firewalls are working together? On the firewalls with "show user-identity ad-agent we see, the following:
-Authentication Port: udp/1645
-Accounting Port: udp/1646
-ASA Listening Port: udp/3799
Why Cisco does use 1645 and 1646 and not 1812 and 1813?The Listening Port is used for what purpose? we tried the AD Agent modes full- download and on-demand with the same effect.