Cisco Routers :: Change A Pix 506e For Rv042 / Good Or Bad Move?
Dec 14, 2011
i'm looking to change my pix 506e for an rv042,is it a bad move or a good move ? is the rv042 much better than the 506e? i want to change to an rv042 because it's easier to manage! 506e is currently doing this :
-firewall for a web hosting company (7 servers)
-2 vpn tunnel
-one-to-one nat.
performance side : is the rv042 much better than the 506e? should i pick up an rv082 or an rv016 ? are they much better than the rv042 ?
View 2 Replies
ADVERTISEMENT
Mar 27, 2013
I have an RV042 that I have configured to send alert logs to a comcast email address. Recently comcast changed their SMTP port from 25 to 465. I can't find where to change the port settings in the RV042 to send the router logs via port 465.
View 1 Replies
View Related
Nov 4, 2012
We will be moving to a new data center in the very near future and with them our WAN IP addresses will be changing. Any best course of action for changing the IP addresses throughout the firewall configuration? Would it be possible/suggested to export the running-config, make the neccessary changes, then import the config? I am familiar with the ASA 5510 only so far as changes are required. It is not something I work with on a regular basis.
View 5 Replies
View Related
Apr 26, 2012
I am considering the RV180 as a wired router replacement to my current wireless and I can not find any user reviews, comments or ratings. I live in an area with a very poor wireless reception for our Sprint Cell phones (Still under contract) and I have a Sprint Airave which boosts the wireless signal for the cell phones. The Airave transmits on a 2.4Ghz band and it is stepping on my Internet wireless signal causing poor reception thought my 2-story house.
Due to this problem, I am considering installing a business class network with a router, PoE switch, and a strong Access Point. My house is pre-wired for with CAT5 wiring. I have looked at the EnGenuis EAP-350 Access Point (800Mw and 29dBm gain and PoE), The RV180 Gigabit Router, and the Cisco SD208P 8-port gigabit switch with 4 port PoE support for the Access Point. The switch will be located in a wall junction box so I need a switch with minimal ventilation requirements. Is the RV180 and SD208P the right choice to integrate in my network?
My experience with Linksys and Cisco products have been Great so I would like to stay with Cisco. I have looked at a competitors router (Netgear FVS318G-100) but the user reviews were very poor. I am not sure if I need a managed switch or not, as I will have one primary laptop running during the day and up to 3 other computes(2 laptops & 1 desktop), a wireless tablet (android), and a Xbox (wired connection) for the family (of course not all running at the same time).
View 1 Replies
View Related
Jan 24, 2013
I have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
View 2 Replies
View Related
Aug 22, 2012
I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?
View 5 Replies
View Related
Nov 28, 2011
What are procedures to deactivate di-604+di-704 routers+make the repeaters,connecting each of them,in a wired fashion,to my Belkin wireless N router?
View 1 Replies
View Related
Feb 20, 2012
it is possible to enable Xauth on pix. I have read multiple threads about using the following cmds:
username test123password testing privilege 2
aaa-server LOCAL protocol local
crypto map mycrypto client authentication LOCAL
However the f/w wont let me add the crypto map cmd, just comes back with the following:
PIX(config)# c.rypto map mycryptomap client authenication LOCAL
Usage: [ show ] crypto { ca | dynamic-map | ipsec | isakmp | map | sa } ...
show crypto engine [verify]
[ show | clear ] crypto interface [counters]
I also tried the following, but they dont work and I am not sure if they are meant for Xauth since I was under the impression that it had to be enabled globally.
PIX(config)# vpngroup test authentication-server LOCAL
Protocol "local" is not supported for authentication of remote users of a h/w client
PIX(config)# vpngroup test user-authentication
[code]....
View 3 Replies
View Related
Feb 27, 2012
I have two Internet connections-
1-DSL Modem (WAN1-Internet Port)
2-Cable Modem-Comcast (WAN2-DMZ/Internet Port)
I connected the DSL (WAN1-Internet) port in and the Cisco RV042 was able to get an IP automatically. I tested the connection and it works just fine. Then I connect the Cable Modem-Comcast (WAN2-DMZ/Internet Port) in and I have the RV042 automatically optain IP address. But it just says 0.0.0.0. I've tried release/renew and that does nothing. Also, when I connect the 2nd Internet connection the Internet goes down. The only way it goes back up is when I disable under the PORT MANAGMENT setting.
All the settings have been kept to the default.How can I get the router to obtain an IP address from the Cable Modem-Comcast (WAN2 DMZ/Internet Port).
View 5 Replies
View Related
Mar 6, 2012
We have an Cisco RV042. We need to setup a VPN with a business partner who is already using our current IP scheme on another VPN with another client. They have asked us to NAT our IP's from 192.168.25.x to 192.168.245.x
I can't seem to figure this out on this router. I have done it on a Sonicwall and Watchguard, but can't seem to get it to work on the RV042.
I have setup the VPN and the One-To-One NAT. The tunnel will connect (using the 245.x IP as our local IP on the VPN setup), but no traffic will pass through.
View 1 Replies
View Related
Mar 4, 2011
How to configure SSH access on my PIX 506e. I would like to use local authentication with no AAA server. Also I would like to have telnet disabled completely.
View 3 Replies
View Related
Oct 28, 2012
I seem to be having an issue with my PIX configuration. I can ping the VPN client from the the internal network, but can cannot access any resources from the vpn client. [code]
View 4 Replies
View Related
Mar 17, 2013
There is a PIX 506E and ASA5510, with different connection to service provider. Problem is Apple remote users can't access resources protected by the PIX506E. Apple users can access resources protected by ASA5510. Physically the PIX and ASA are in close proximity with no physical connections. Is it possible for Apple users to authenticate with the ASA and the traffic get routed to and get authenticated by the PIX, inorder to access resources?Due to bandwidth restrictions, a DMZ on the ASA will not be created at this time inorder to consolodate firewalls. Currently 2 x T1 is the connection between ASA and ISP; 1 T1 connects PIX to ISP.
View 1 Replies
View Related
Nov 19, 2012
I have a PIX506E that was resently reset and it has version PIX Version 7.1(2) . It either uses some different commands or I am not using them correctly. [code]
View 2 Replies
View Related
May 4, 2013
So i got a Cisco PIX 506e from a friend and want to set it up for a VPN. Though i cant download the PDM (PIX Device Manager) since i dont have a Contract or something like that. So i cant set it up.
View 1 Replies
View Related
Jul 7, 2011
I have 2 firewalls in my network: ASA 5505 and PIX 506E. Both firewalls's internal network is in the 192.168.0.0/24 subnet but their external addresses are different of course. The inside IP for ASA 5505 is 192.168.0.254/24 whereas the PIX is 192.168.0.1/24. I've successfully configured VPN on the ASA 5505. I'm able to VPN to the ASA and can ping / access hosts that have the 192.168.0.254 as their gateways.However, I'm unable to ping/access hosts behind the PIX. What do I need to do in order to allow access to the network behind the PIX after I VPN to the ASA? Also, I'm unable to ping 192.168.0.254 after I VPN to the ASA.
View 5 Replies
View Related
Apr 29, 2012
I need to replace an ageing PIX 506e with an ASA 5505.The current setup looks like this: The PIX is used for site-to-site VPN connection via the WAN 2 link. The WAN 1 link is used for general Internet connectivity.I don't have access to the Draytek Router as it is supported by a 3rd party, but I believe it uses static routing to direct the relevant traffic to/from the PIX.
When I replace the PIX with the ASA, the inside i/f connection experiences dropouts - but no errors show in the logs.The only significant difference I can see in the config is that the ASA utilises VLans for the inside & outside interface configs - I used the PIX-to-ASA Migration tool to make the initial configuration on the ASA.In tests, if I only connect the inside i/f of the ASA, pings from the LAN are stable. Once I connect the outside i/f, pings timeout approx 80% of the time.
View 2 Replies
View Related
Jan 10, 2011
I am new to the PIX firewall. And recently implemented the PIX 506e in my network. I wants to know how we can monitor the system that is generating the more traffic on Network through Firewall.
View 4 Replies
View Related
Mar 5, 2011
I am trying to add a username to the local database for remote VPN connection but always i get this error when I add,Encrypted password is of incorrect lengthUsername addition failed.
View 1 Replies
View Related
Apr 2, 2012
I am trying to give a vendor VPN access so that they can remotely monitor and diagnose their installed heating and cooling equipment. I dont know where to start and I apologize in advance for my ignorance. I am technically savvy but i have no Cisco knowledge base.
It is a PIX 506e firewall with PIX v6.3.
View 1 Replies
View Related
Mar 11, 2013
I just got a PIX 506e from a friend that was not longer using it. I'm trying to get started with the configuration page. I've reset it to factory defaults, rebooted and connected up ethernet. I can ping the device at 192.168.1.1 and access it via console. I browse the site https://192.168.1.1/startup.html, get the invalid ssl certification, get a login prompt (user/pass) and as the document says I leave it blank. As soon as I hit ok it goes to the 404 error Page Not found.
View 4 Replies
View Related
Mar 22, 2011
What is the easiest way to restore my config? I backed it up yesterday with my tftp server. Today I made some changes and messed some things up and need to restore the config from yesterday.
View 1 Replies
View Related
May 20, 2012
i was planed to make a vpn over rv042 so i get the rv042 connected behind a thosmon 456(configured as a bridge) and 1 static ip ... and i configured the vpn and worked great ...but due to some circumstance i get a package of 6 ips insted of the old ip , so when i try to configure the router with the ISP they but the wan ip 10.232.x.x and told me that an internal ip from there lan ... and give me the 6 ip of 196.x.x.x to use as 1 for internal interface for the rv042 and 5 for the pc's,now the vpn not working anymore...notice: when try to configure the vpn tunnle in the local securty setting i mark the ip only and the ip that abear is the wan ip 10.232.x.x but i can't ping that ip beside i can ping the internal ip of the router 196.x.x.50does rv042 can support static and virtual ip inside the lan |! can i configure the thomson as pppoe and use one static ip from 196.x.x.x as wan ip for it ... and use anther 196.x.x.x ip for the rv042 to get access from outside and connect the lan to the rv042 with internal ip 192.168.x.x ...so i can access the vpn from outside .....and can connect the device i need to use static ip to the thomson ...
View 0 Replies
View Related
Sep 23, 2011
Firmware v4.0.4.02 has a nasty bug in the VPN section. If you switch to "IP by DNS Resolved" (yes, it says "Resolved" instead of "Resolution". Gotta love all the Engrish in the RV042!), it will automatically populate the field with "@yourdomain.com". This will cause the VPN to not lookup the proper IP address. Simply deleting the atmark after it populates will fix the problem.
Let's see what happens when we validate a Cisco RV042 webpage:
Errors found while checking this document as HTML 4.01 Transitional!
Result: 353 Errors, 1 warning(s)
Don't even get me started on the horrible Javascript...
View 0 Replies
View Related
Apr 24, 2013
i am trying to make a simple Site to SiteVPN between two offices, one has Cisco ASA and one has RV042 router.when traffic initiated from ASA side, i keep getting this message in Debug and tunnel wont come up
.
[IKEv1]: Group = A.A.A.139, IP = A.A.A.139, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.Apr 26 00:15:53 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
whereas if traffic initiated from RV042 side, i keep getting this message in debug and tunnel wont come up.
Apr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, Oakley proposal is acceptableApr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, IKE SA Proposal # 1, Transform # 0 acceptable Matches global IKE entry # 6Apr 26 00:43:44 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, Freeing previously allocated memory for authorization-dn-attributesApr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, PHASE 1 COMPLETEDApr 26 00:43:45 [IKEv1]: IP =RV.RV.RV.139, Keep-alive type for this connection: DPDApr 26 00:43:45 [IKEv1 DEBUG]: Group =
[code].....
View 1 Replies
View Related
Sep 27, 2012
Apparently one of my two ISPs,CenturyLink, supports 6rd connections to IPv6.
This is supported natively on my Q1000 ActionTec modem, however my modem is in "transparent bridging" mode, so that the RV042 v3 can be the only router.
how to configure the RV042 to operate in this manner.
Per the CenturyLink FAQ: the IPv6 address space is:
2602::0 /24
Most importantly, can I do this WITHOUT buying a new modem.
View 2 Replies
View Related
Aug 28, 2011
I have a RV042 router (Ser#: NKS10462300, HW V3) running Firmware version v4.0.2.08-tm (Jan 14 2011 22:08:38) set up as a gateway. Right after it boots I am able to long into its web interface but shortly after that if I try to log into it I go through a very log time out while the web page is waiting the router to respond and then eventually IE comes back and says it 'cannot display the web [age'.
View 30 Replies
View Related
Jan 14, 2013
I have a Cisco RV042 VPN Router and I have added a group vpn, but when I am trying to connect I got an error that the remote vpn server isn't responding.
Here's my log:
2013/01/15 12:24:53 [STATUS]OS Version: Windows 7
2013/01/15 12:24:53 [STATUS]Windows Firewall Domain Profile Settings: ON
2013/01/15 12:24:53 [STATUS]Windows Firewall Private Profile Settings: OFF
2013/01/15 12:24:53 [STATUS]Windows Firewall Private Profile Settings: OFF
2013/01/15 12:24:53 [STATUS]One network interface detected with IP address MY HOME IP
[code]....
If I am trying to connect the status of the vpn user in the remote interface is "online".I have deactived my firewall at home and at the server for testing purposes.
View 2 Replies
View Related
Apr 19, 2012
I am looking to configure RV042 for VPN access to local machines and Win 2008 server. The story: Had issues with remote printers being created for clients logging into old Linksys RV042 with Linksys VPN software. First Tech exposed server without security, and it had to be removed as it was being attacked, but did not fix printing issue. 2nd tech could not get VPN to work after 1st tech. 3rd tech, 4hours, and I got that the router is a piece of ... So I'm out over 1000, and not able to have a simple router set up. The present situation. New RV042 with firmware V4.1.1.01, using Cisco VPN client 5.0.07.0410, most XP 32 bit machines coming into network, one 64 bit win 7. My clients have been unable to access their data for too long.
View 3 Replies
View Related
Feb 6, 2012
Is there any documentation out there on a step-by-step instructions on setting up a vpn on a RV042 router?
View 1 Replies
View Related
Apr 30, 2012
I'm trying to set up 2 subnet with two RV042 routers. One router will act as a gateway and both WAN ports will be used by two different isp connection. The first router (gateway) LAN IP will be 192.168.0.1/24. I would also like to set up another router behind the gateway with with separate subnet 192.168.1.X/24. And I would like clients on the 192.168.1.x subnet to use the internet through the gateway router and clients on the 192.168.0.x subnet to access resources on the 192.168.1.x subnet. Am I able to do this with two RV042?
View 6 Replies
View Related
Sep 2, 2012
The issue is when I am using PPTP the router seems to die, not every time but I would say about once a week now. I am the only PPTP user, simply using RDP. A few hours into an RDP session the PPTP connection drops and cannot be re-established, or quickvpn, nothing. Routing still works (somewhat, high latency) locally.
When I've checked the logs both times I see:
TimeEvent-TypeMessageSep 3 17:07:56 2012KernelOut of memory: Killed process 14354 (pppd). Sep 3 17:07:56 2012KernelOut of Memory: Kill process 14354 (pppd) score 177 and children. Sep 3 17:07:56 2012KernelOut of memory: Killed process 14367 (sh). Sep 3 17:07:56 2012KernelOut of Memory: Kill process 14354 (pppd) score 234 and children. Sep 3 16:46:41 2012KernelOut of memory: Killed process 14330 (pppd). Sep 3 16:46:41 2012KernelOut of Memory: Kill process 14329 (pptpctrl) score 134 and children. Sep 3 16:46:41 2012KernelOut of memory: Killed process 14324 (pppd). Sep 3 16:46:41 2012KernelOut of Memory: Kill process 14324 (pppd) score 177 and children. Sep 3 16:46:40 2012KernelOut of memory: Killed process 14328 (sh). Sep 3 16:46:40 2012KernelOut of Memory: Kill process 14324 (pppd) score 234 and children. Sep 3 15:36:15 2012KernelOut of memory: Killed process 14187 (pppd). Sep 3
[code]....
View 3 Replies
View Related
Nov 11, 2012
I have an RV042 connected via VPN to the office (to a LinkSys DFL-700). Sometimes the VPN is dropped and never activates again. In this state, if I try to connect to the WEB interface, I can log in, but the router hangs at the login screen. I have to power recycle the router to make it work again.
Updated to latest firmware 4.2.1.02 for V3 hardware. The funny thing is that services from the WEB routed through to local IP adresses on the lan is still accessible. I have setup PPPT VPN on the router, and that also fails to work.
Is there, as a workaround, any possibility to access the routers reset page or access via TELNET to reset the router? This migth be useful, when I'm out. (I have a backup solution to access the local network at home).
View 3 Replies
View Related
