I have 2 firewalls in my network: ASA 5505 and PIX 506E. Both firewalls's internal network is in the 192.168.0.0/24 subnet but their external addresses are different of course. The inside IP for ASA 5505 is 192.168.0.254/24 whereas the PIX is 192.168.0.1/24. I've successfully configured VPN on the ASA 5505. I'm able to VPN to the ASA and can ping / access hosts that have the 192.168.0.254 as their gateways.However, I'm unable to ping/access hosts behind the PIX. What do I need to do in order to allow access to the network behind the PIX after I VPN to the ASA? Also, I'm unable to ping 192.168.0.254 after I VPN to the ASA.
I seem to be having an issue with my PIX configuration. I can ping the VPN client from the the internal network, but can cannot access any resources from the vpn client. [code]
I need to replace an ageing PIX 506e with an ASA 5505.The current setup looks like this: The PIX is used for site-to-site VPN connection via the WAN 2 link. The WAN 1 link is used for general Internet connectivity.I don't have access to the Draytek Router as it is supported by a 3rd party, but I believe it uses static routing to direct the relevant traffic to/from the PIX.
When I replace the PIX with the ASA, the inside i/f connection experiences dropouts - but no errors show in the logs.The only significant difference I can see in the config is that the ASA utilises VLans for the inside & outside interface configs - I used the PIX-to-ASA Migration tool to make the initial configuration on the ASA.In tests, if I only connect the inside i/f of the ASA, pings from the LAN are stable. Once I connect the outside i/f, pings timeout approx 80% of the time.
How to configure SSH access on my PIX 506e. I would like to use local authentication with no AAA server. Also I would like to have telnet disabled completely.
I am trying to give a vendor VPN access so that they can remotely monitor and diagnose their installed heating and cooling equipment. I dont know where to start and I apologize in advance for my ignorance. I am technically savvy but i have no Cisco knowledge base.
I have a problem with PIX 506E that meets the version 6.1, and in an simple computer network equipment seems to behave in strange ways because some web sites do not open or very open slow thereby its operation impracticable. On the other hand other web sites open normally.
Querying the web site of the Cisco, I found several documents discussing the same problem but in a later version ( 7.0 ), not in this version 6.1.
I've tried removing the pix from the network , not the error occurred, again insert pix however tested only with a machine, without the rest of the network and the problem persists
i want my ASA 5505 8.2(5) to access my proxy server on remote lan through VPN my VPN is OK, all PCs of local network can access to remote network.but ASA on local network can't access to remote network.i think it's a NAT problem but ....
local network 192.168.157.0/24 local IP ASA 192.168.157.1 remote netword 10.28.0.0 /16 remote proxy 10.28.1.26 my conf
Cisco ASA 5505 Cisco Adaptive Security Appliance Software Version 7.2(4) Device Manager Version 5.2(4)
I have and vpn tunnel between a pix network (192.168.200.0/24) and an asa network (192.168.100.0/24); it's been running fine for awhile now but this morning i've come in an i can not access anything on the pix network, (mail, file & web servers). Each attempt to access results in a SYN timeout.
6 Nov 30 2012 14:24:01 302014 192.168.200.9 192.168.100.115 Teardown TCP connection 6014 for outside:192.168.200.9/135 to inside:192.168.100.115/51240 duration 0:00:30 bytes 0 SYN Timeout
i have a problem with my asa 5505 Remote VPN Connection with local network access , the VPn is working fine and connected , but the problem is i can't reach my inside network connection of 192.168.30.x , here is my configuration
I have two ASA5505 with a site to site VPN.One of the ASA is connected to the internal network 192.168.150.0.The other one is connected to 192.168.151.0.
I have also configured IPSec Cisco client VPN to the one which is plugged to 192.168.150.0.
I would like to know if it is possible for a client connected with the Cisco VPN to access the network 192.168.151.0 through the site to site VPN.
What I got is a 5505 ASA firewall and I'm connected to it via VPN. I'm pulling an 192.168.169.x address because that's what we set their company's internet LAN to. Which is what we want. What I can't do while I'm VPN'd in is ping from the internet network to the DMZ, and the same when I try and ping from the DMZ to the internal network.
The DMZ is on a 196.0.0.x network.The internet network is 192.168.169.x network.
I don't need them to have internet access on the DMZ I just want to be able to access it from the internal network. What is going on is we need them to be able to VPN into the DMZ and access their equipment. At this point it would just make me happy to be able to ping from the internal network to the DMZ and I can figure it out from there I've setup rules and applied them and when I wasn't having success I referred back to defaults. Right now the rules are set at default, any thing in and anything out, on both internal and DMZ. I'm using a VPN client and going through Cisco ASDM Launcher to setup the rules and static routes, I haven't done anything with the command line. All the research I've done everyone does it command line, I find it easier to do it GUI. This is my first time working with an ASA firewall.
I´m tring to configure ASA 5505 with VPN Cleint, to access a remote network over a L2L with another ASA 5505, but no sucess. Is there any special feature to this work?
I have a Cisco ASA 5505, with basic 50 license, that is connected directly to the Cable Modem with a public IP. I have VPN configured and active on the Outside interface. When we connect, we connect just fine with no errors, but we are not able to access any resources on the remote network.
ASA IOS version 8.2(5) Remote Network IP: 10.0.0.0/24 VPN IP Pool: 192.168.102.10 - 25
What should i do on my Cisco ASA 5505 firewall to grant access to my network systems to access internet via gateway. I use ASDM to configure the firewall.
I have one user who is unable to Access Remote Network resources when connected to the VPN on his home network. VPN shows connected and he is given a remote IP from the VPN Pool, but he cannot ping any IP on our network. When connected using Sprint Wi-Fi card he is able to connect and access remote network from the same laptop. Maybe there is some network overlap that I am missing.
see attached firewall config (zzz... being firewall public IP) and remote user route table. ASA 5505 VPN Client 5.0.07.0290
I've setup my VPN on the cisco ASA 5505 which works perfectly, users from outside can access my internal LAN. Now what i want, Is to create another VPN Tunnel group with another set of IP in which i want to allow them access to one server inside our LAN. See below details of network. [code]
We have configured a Cisco ASA 5505 with AnyConnect access. This works great. However, these users cannot seem to ping devices on the private network. We have configured all devices on the network with a 10.10.10.0/24 address space. The inside interface of the ASA i 10.10.10.1/24 and the VPN return addresses are 10.10.10.50 - 10.10.10.65/24.They users can utilize SSH and Oracle or MySQL calls but cannot seem to ping. Obviously, I am over looking something.
When I start a VPN-session my server looses internet access. The server is host for a few virtual machines and they have internet access.using 5505 and asa is version 8.4(2). [code]
I have a 5505 between a vendor router & my company network, vendor is not able to access devices on internal network. I am also not able to access the firewall via asdm
I am using two firewalls to connect two different offices. Firewall 5510 is running ASDM 6.3 and 5505 is running ASDM 6.2, Problem is that even after connecting two sites, i am unable to ping remote network from either side. I am mentioned static route as tunneled.
it is possible to enable Xauth on pix. I have read multiple threads about using the following cmds:
username test123password testing privilege 2 aaa-server LOCAL protocol local crypto map mycrypto client authentication LOCAL
However the f/w wont let me add the crypto map cmd, just comes back with the following:
PIX(config)# c.rypto map mycryptomap client authenication LOCAL Usage: [ show ] crypto { ca | dynamic-map | ipsec | isakmp | map | sa } ... show crypto engine [verify] [ show | clear ] crypto interface [counters]
I also tried the following, but they dont work and I am not sure if they are meant for Xauth since I was under the impression that it had to be enabled globally.
PIX(config)# vpngroup test authentication-server LOCAL Protocol "local" is not supported for authentication of remote users of a h/w client PIX(config)# vpngroup test user-authentication
There is a PIX 506E and ASA5510, with different connection to service provider. Problem is Apple remote users can't access resources protected by the PIX506E. Apple users can access resources protected by ASA5510. Physically the PIX and ASA are in close proximity with no physical connections. Is it possible for Apple users to authenticate with the ASA and the traffic get routed to and get authenticated by the PIX, inorder to access resources?Due to bandwidth restrictions, a DMZ on the ASA will not be created at this time inorder to consolodate firewalls. Currently 2 x T1 is the connection between ASA and ISP; 1 T1 connects PIX to ISP.
I have a PIX506E that was resently reset and it has version PIX Version 7.1(2) . It either uses some different commands or I am not using them correctly. [code]
So i got a Cisco PIX 506e from a friend and want to set it up for a VPN. Though i cant download the PDM (PIX Device Manager) since i dont have a Contract or something like that. So i cant set it up.
I am new to the PIX firewall. And recently implemented the PIX 506e in my network. I wants to know how we can monitor the system that is generating the more traffic on Network through Firewall.
I am trying to add a username to the local database for remote VPN connection but always i get this error when I add,Encrypted password is of incorrect lengthUsername addition failed.
I just got a PIX 506e from a friend that was not longer using it. I'm trying to get started with the configuration page. I've reset it to factory defaults, rebooted and connected up ethernet. I can ping the device at 192.168.1.1 and access it via console. I browse the site https://192.168.1.1/startup.html, get the invalid ssl certification, get a login prompt (user/pass) and as the document says I leave it blank. As soon as I hit ok it goes to the 404 error Page Not found.
What is the easiest way to restore my config? I backed it up yesterday with my tftp server. Today I made some changes and messed some things up and need to restore the config from yesterday.
I'm getting an error message on my 506E that is saying not enough flash space to install the new version 8 software. I did a clear flashfs command and then tried again but get the same error. Do the PIX 506E can be upgraded from version 6 to version 8? I am trying to install pix804-28.bin.
I trying to do password reset on a 506e that I got with the current password unknown. I've gone to the Cisco URL for the reset: [code]
I am using the correct bin file as I checked with my pix version. Also I CANNOT ping the firewall from a PCor system on the network, but CAN ping everthing from the PIX.I've tried using interface 1 but no go. Also I've checked the TFTP software (Solarwinds) is running fine and I've unblocked it in XP's firewall.
So I have a Cisco PIX 506e that I've modified a bit, but am quite happy w/ when it comes to performance and configuration (I can actually set up the VPN server w/o too much thought.) I also have a Mikrotik Routerboard 750, I'm no longer using it as my router due to a few config issues I had plus the fact I had to hard code my internet gateway's arp address into the device due to some issues.
What I am wanting to do, which I'm sure is possible and easily accomplished (I just don't have the time right now to try it) is set the routerboard up behind my pix and have it function as an ipv6 router, while the pix handles my ipv4 duties. I've already set up the routerboard w/ an ipv6 tunnel broker when I had it running as my router, I am just curious if it will work in a similar fashion when configured behind an ipv4 device.
I like to set up a pix and router for this network for a small buss, but I need to know what type of cable do I need to set this connection to work straight through or a cross over cable? also I need a subgestion if a nat would work better on the pix or leave it on the router?
