Cisco VPN :: 2691 - EzVPN With XAuth Auto Connect
Nov 17, 2008
I have problem auto connect Easy VPN client to Easy VPN server using saved X auth username/password. The ez vpn client is a Cisco 2691 using IOS 12.4.15T7. The config is as follows:
crypto ipsec client ezvpn EZ
connect auto
[code]....
the router keeps prompting me to manually enter username/password. connectivity will work be established after i manually enter the username/password. But this is not what i desired. I need it to connect automatically.
The Ez vpn server is a 7200 running 12.4.22T. Config as follows:
aaa new-model
aaa authentication login USERAUTHEN local
aaa authorization network GROUPAUTHOR local
[code].....
View 7 Replies
ADVERTISEMENT
Feb 20, 2012
it is possible to enable Xauth on pix. I have read multiple threads about using the following cmds:
username test123password testing privilege 2
aaa-server LOCAL protocol local
crypto map mycrypto client authentication LOCAL
However the f/w wont let me add the crypto map cmd, just comes back with the following:
PIX(config)# c.rypto map mycryptomap client authenication LOCAL
Usage: [ show ] crypto { ca | dynamic-map | ipsec | isakmp | map | sa } ...
show crypto engine [verify]
[ show | clear ] crypto interface [counters]
I also tried the following, but they dont work and I am not sure if they are meant for Xauth since I was under the impression that it had to be enabled globally.
PIX(config)# vpngroup test authentication-server LOCAL
Protocol "local" is not supported for authentication of remote users of a h/w client
PIX(config)# vpngroup test user-authentication
[code]....
View 3 Replies
View Related
Jul 1, 2006
how to disable XAuth for Remote VPN users on the ASA 5510 running 7.2(1)?
HPMFIRE(config)# tunnel-group vpn3000 general-attributes
HPMFIRE(config-tunnel-general)# authen
HPMFIRE(config-tunnel-general)# authentication-server-group none
ERROR: The authentication-server-group none command has been deprecated.
The isakmp command in the ipsec-attributes should be used instead.
--[code]....
I couldn't find anything under isakmp to disable it.
View 2 Replies
View Related
Dec 18, 2010
I've gotten a dir-600 and have been trying to configure it so that it won't auto connect to the internet. Some people in my network prefers to manually connect to the internet from their pppoe dial-up on their PC. I've tried changing it to static or dynamic ip in the LAN config, but everyone connected to the router from LAN couldn't dial out as well. changing it to ap allowed everyone (including wireless) solved the problem. but doing so, i am not able to access the router. the default ip's don't work, nor could i find the ip of the router on the network.
so what i want to do is reset it to factory settings and just use it as a hub/switch w/ wireless. don't want to use it to connect to the net automatically.
View 2 Replies
View Related
Sep 15, 2011
i have a cisco 2691 and i would like to install NME-16ES-1G-P to set up a Voice Lab environment.Is it possible to have 802.3af PoE support for 2691 using the NME-16ES-1G-P updating the AC power supply? Or does any other solution exist to have 802.3af support on 2691?
View 5 Replies
View Related
Aug 23, 2011
I'm renting a basement at the moment and I am trying to get my desktop to connect to their wireless network. My laptop is fine but the desktop just keeps restarting itself when its attempting to connect. This didn't happen before I moved. When it finishes restarting there's a popup asking to send a error report to Windows. Since I have no internet that won't I clicked the details of the error message this is what I see.[CODE]
View 2 Replies
View Related
Dec 25, 2012
About six months ago I replaced my old router (some generic 802.11b/g router I got for free with a rebate years ago and which lasted a few years) with a Dir-601 after the old router started intermittently cutting out. Setup of the Dir-601 was straightforward enough and I have WEP enabled. Both my Macbook and my wife's Macbook can connect fine if we choose the router from the drop-down wireless network list, and the router has been consistently reliable in maintaining a connection as long as the OS is running.
HOWEVER, neither computer will remember the wi-fi network and won't auto-connect when waking up from sleep or after a restart. Our iPhone and Android smartphones remember the network just fine and auto-connect every time, zero issues. I've gone through all the typical Mac troubleshooting steps, deleting saved network connections and re-establishing new ones. Never solves the problem. We always have to go to the wireless network menu and manually select the wifi connection to connect to.
It's not the Macbooks. Firstly, both macbooks have the same issue, and they're each running different MacOS versions, so there's no version-specific issue that can be at play here. Secondly, neither macbook had this issue with any previous wifi router. Thirdly, anywhere else we take our macbooks where we've set up a wifi connection, they remember it and auto-connect without us having to manually select the network. The only network where we have to manually select the network every time is the one set up with the Dir-601. In fact, we're at my inlaws for the holidays and our Macbooks have been auto-connecting to their router each and every time.Is there a setting I'm not seeing on the Dir-601 admin page?
View 3 Replies
View Related
Oct 24, 2012
I've spent the last two days working on this problem and it is killing me! I know the answer has to be something simple, but despite hours of searching and trying different things, I just can't seem to fix it.Essentially, I am going to be installing a Cisco 2691 and use it as the default gateway for a small business. It will be directly connected to a cable modem with a static IP. The other Ethernet interface is going to connect to a 2950 switch with a couple different VLANs.
The problem I'm having is that I can ping anything external from the router itself. From the clients connected to the 2950, I can ping IPs in other VLANs, and I can ping up to the IP of the external interface, but no pings go beyond that.I've set up NAT overload on the router, and when I do a debug ip nat, I see the pings trying to get through with the proper translations, but I still don't receive ICMP replies back.I set up GNS3 to simulate what I'm trying to accomplish (since it emulates a 2691). Attached is a jpg of the topology -- on the right is the "simulated ISP" with 3 loopback networks and one host on a different subnet. The 2691 has a static route to the "Internet" router, and can ping everything attached to the router, including the host. The host (5.5.5.5) can also ping the outside interface of the 2691 (50.50.50.2).
However, the hosts behind the 2691 can't ping past 50.50.50.2. The 192.168.0.x network can be ignored, because that network won't need to access the Internet. But the 10.10.20.x (VLAN 20) and 10.10.30.x (VLAN 30) networks will need to. In the simulation, the hosts are 10.10.20.5 and 30.5. They can ping each other, their default gateways, and the 2691 outside interface (50.50.50.2) but not the other side, the "Internet" router at 50.50.50.1 or beyond.
[code]....
View 4 Replies
View Related
Jul 1, 2012
I am working on a Compaq cq50 which I have re-formatted running Vista Home Premium.It connects fine with my LAN, and also connects wireless when I push the wireless switch...however it won't connect wireless automatically when I boot..I always have to push the button.I don't think that is normal.I went to services and stopped the auto wlan and then deleted the existing profile and then re-established the wlan services and account..
View 4 Replies
View Related
Apr 14, 2013
I set up a DIR-655 router for a friend 4 years ago and it's worked reliably with all of their equipment since. They have wireless printers, iMacs, pc laptops and iPhone 4S's, all connecting without any problems. Recently, they got an iPhone5 and it will not connect to their home wireless automatically, they have to re-enter the password each time. They've tested their iPhone 5 on other networks and they do not have to re-enter the password. Apple and ATT are blaming the router. I do not live near them and I'm going to have to facilitate them remotely. At this point, I believe their router is configured with WPA2, but I can't be sure. Which configuration will work with the iPhone 5, as well as their other, older, devices that have worked for 4 years
View 1 Replies
View Related
Mar 24, 2013
Just installed N600 Play router. All computers and phone connect fine, but computers won't auto connect after reboot or sleep. With old router this worked fine.
View 4 Replies
View Related
Dec 14, 2012
I have 2691 Router conencted to Internet and it is doing Nat.
This connects to 3550A Switch which has connection to 1811W Router.
I setup VPN between 1811W and 3550A.
3550A has connection to 2691 via ospf.
OSPF is running between 1811w and 3550A.
1811
1811w# sh crypto isakmp sa
IPv4 Crypto ISAKMP SA
[Code]....
View 7 Replies
View Related
Jan 13, 2012
I have verified that I am set to auto connect however my wireless does not do so upon start. I have to do so manually each time I use my computer. This is a new problem since installing the newest driver update because I could not connect at all or randomly. The update fixed the connection problem and I no longer have dropped connections and wifi connection back to normal. HOWEVER it has left my auto connect nonfunctional.
View 7 Replies
View Related
Aug 16, 2012
I have a Dell E6420 running WIN7 32bit. It is running the Dell broadband utility. I am trying to find a way to keep the users from selecting auto-connect in settings>config. I am looking for a registry key or something that can be done from the admin side to stop this.
View 3 Replies
View Related
May 21, 2013
I have router Cisco 2691 and Cisco 7604 and want to play with AutoQoS Cisco feature. But on both there is no such command But why?
View 1 Replies
View Related
Dec 20, 2011
My 2691 Router has already 2 serial cards WIC-1DSU-T1 installed, When i install the 3rd serial card and reboot the router, it detects the 3rd card installed but 3rd card has no light.
When i do sh ver it shows 3 cards installed.
When i install this 3rd serial card to other Router then light shows on card and it works fine
So i am thinking if 2691 Router only supports 2 serial cards?
View 3 Replies
View Related
Nov 22, 2011
I was wondering if i can enable url filtering on my 2691 or 2651XM routers so that if someone visits any website i can see that under router logs. right now i am using kiwi syslog that logs the router activities.
View 3 Replies
View Related
Sep 5, 2012
We're starting to share video across our network and would like to setup multicast to conserve at least some of the bandwidth. We have a broad mix of equipment (A Catalyst 6509-E at the core, a combination for Cisco 2691 & 2811 routers, and a whole lot of Catalyst 3500, 3550, 3560 switches at a hundred locations. Where would I begin? Would I need to define routing for the multicast IP addresses (224.0.0.0)? Would I need to setup interfaces & IP networks where each multicast device is located like I would for a new IP subnet?
View 1 Replies
View Related
Dec 3, 2011
On my 2691 Router i see the buffer leak due to syslog
2691Router# sh buffers leak
Header DataArea Pool Size Link Enc Flags Input Output User
650743C4 F200084 Small 0 0 0 0 None None Init
[Code].....
View 17 Replies
View Related
May 10, 2012
I have 2691 router with following config
line console 0
login local
password xty
When i remove the login local from the line console i connect to console port and press enter it shows router prompt 2691Router> but i am unable to go to enable mode.If i telnet to router then i put username and pw then it goes straight to enable mode.
vty config is
line vty 0 4
exec-timeout 600 0
logging synchronous
login local
length 500
transport input telnet ssh
escape-character 3
Any reasons why i can not go to enable mode by console?
View 3 Replies
View Related
Apr 6, 2012
Here is my Lab Setup: 2691 is BGP nei to R4 router and they are not directly connected. 2691 and R4 are in same AS 6500. 2691 Config---router ospf 1 network 3.3.3.3 0.0.0.0 area 0 . Its advertising its loop back IP to OSPF domain.
router bgp 6500
no synchronization
bgp log-neighbor-changes
neighbor 6.6.6.6 remote-as 6500
neighbor 6.6.6.6 update-source Loopback3
[code]...
R4 Router
router ospf 11
log-adjacency-changes
network 6.6.6.6 0.0.0.0 area 0
[ code].....
We can see that 2691 and R4 are BGP neis and 2691 has 200.1.x.x routes in its route table. My question is why from 2691 router i am unable to ping any route learned by BGP from R4?
2691Router# ping 50.1.1.0 Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 50.1.1.0, timeout is 2 seconds:.....Success rate is 0 percent (0/5)2691Router#ping 200.1.2.0 [ code]...
View 12 Replies
View Related
Jul 24, 2012
I try to set up EZVPN server. I cannot get any response from server.
View 1 Replies
View Related
Aug 23, 2011
I'm trying to configure a router 7606S with SPA-IPSEC-2G for EzVPN.I was reading some examples in SPa and 7606 documentation but with the current configuration in our router I don't know how to do it.
The router has the SPA installed in slot 3, interfaces G3/0/0 and G3/0/1. The router has the interface G2/0/0 connected to our provider, and we have the interfaces connected directly to network; ie: not vlans, no trunks, ports configured as IP ports conected directly to network.Where can I find an EzVPN example configuration ?
View 2 Replies
View Related
Nov 1, 2012
I'm having trouble configuring with EZVPN on ASA5510. EZVPN uses the local LAN as the source IP, now since the EZVPN is configured on the ASA, it will use its local port 2.2.2.1 as the source local LAN. The actual local network is behind a firewall and i need the tunnel to extend to the 10.10.10.10 network. Is there a way to extend the tunnel to use the 10.10.10.10 as the source LAN? How to do it via the GUI?
View 3 Replies
View Related
Nov 24, 2011
Cisco ASA 5505 50-User Bundle includes 8-port Fast Ethernet switch, 10 IPsec VPN peers, 2 Premium VPN peers, 3DES/AES license
ASA5505-50-BUN-K9. Cisco ASA 5505 Unlimited-User Bundle includes 8-port Fast Ethernet switch, 10 IPsec VPN peers, 2 Premium VPN peers, 3DES/AES license ASA5505-UL-BUN-K9
I think they will support ezvpn, just need confirm .
View 1 Replies
View Related
Mar 31, 2011
I am having an issue get an EZVPN working between a 2811 server and a SR520 client. The symptoms are the SR520 makes multiple connection attempts to the 2811. It appears that sometimes these connections are successful and the SR520 is assigned an IP address but then the tunnel will be dropped and a new session will be started. I've attached scrubed configs for both the 2811 and the SR520. One other note, when connecting to the 2811 with a software VPN client, there are no problems, so I think the problem is with the SR520. On the other hand, the SR520 wasn't having any problems until we switched our VPN server from a UC520 to the 2811.
View 3 Replies
View Related
Jul 10, 2011
I have a 3825 configured as an EZVPN server with 881 routers as clients. One issue I am seeing is that sessions don't seem to time out, such as when a peer's public IP changes. Show crypto ISAKMP peer shows the same host (using device certificates for authentication) with multiple public IPs establishing sessions. I have ISAKMP keepalives configured on the router.
View 2 Replies
View Related
Mar 29, 2011
Our company has a handful of sites that use the EasyVPN technology.On my remote router (Cisco1841) - I add the crypto inside to the FA0/0 and the Loopback0 interface.On the other end my Cisco ASA 5580 - 8.41 code - I have RRI enabled and the tunnel comes up fine.However I only see the static route from the fa0/0 interface on the remote router. I can not figure why I can not see the Loopback0 address?Wondering if this is a limitation or feature not enabled.
I added multiple interfaces on the Cisco 1800 and can see the networks.I run "show crypto ipsec sa" on the Cisco ASA and see the spi encaps/decaps for the loopback, but the SH ROUTE does not show the static route being injected.
View 3 Replies
View Related
Jan 14, 2013
I have lots of 857's routers in the field with mostly the latest OS - 12.4(15)T17 making ezVPN connections to a 2951 with 15.1(4)M5.All the 857's have lookback and vlan interfaces similar to :
interface Loopback0
ip address 50.43.8.1 255.255.255.255
ip tcp adjust-mss 1452
end
[code]....
Now lately for some or other reason we have instances where I can ping either the VLAN or the LOOPBACK interface, but not both. Or I have instances where the 2951 can ping all the interfaces on the 857, but the 857 can not ping the 2951. Or I have instances where the 2951 can not ping the 857, but the 857 can ping the 2951.The way I have been fixing this is either to add crypto ipsec client ezvpn SMS_VPN inside to the loopback interface, or if it is there already to remove it. This usually works for a few days, but then suddenly I have to reverse this again. If that does not work then I usually do lots of clear crypt sess and/or clear crypt ipsec client ezvpn on the 857, or clear crypt sess remote 857_ip_address from the 2951 and then suddenly it starts working again.
View 1 Replies
View Related
Mar 14, 2012
We have a VPN using 857 and 877 routers as remote connecting in to a 2800 EZVPN Server.
The VPN is working fine. However, the VPN connections sometimes (after a few hours/days) seem to "freeze". A "show crypt sess" shows the connections as Up/Active, but you can not ping antyhing from remote to server, or visa versa, nor does any traffic flow. I then added a "isakmp keep-alive" on the 2800, which improved the situation a bit, but not as much as I hoped.
On the 877 I then implemented a IP SLA, with Object Tracking and then use a Event Manager to just issue a "clear crypto session" . This solved the problem.
However, what do I do on the 857 ? It does not support Object Tracking or the Event Manager. Is there any other mechanism to monitor and reset these frozen/stale VPN connections automatically ?
View 5 Replies
View Related
Feb 2, 2012
I try to configure a simple EzVPN infrastructure:
EzVPN Server (CISCO2811, hostname cme) < -- > EzVPN Remote (ASA5505, hostname ezvpn-asa) < -- > Client
Attached you find both configuration of the EzVPN server and remote. The tunnel is getting up and if I ping from the ASA to the Router, I see the packets getting encrypted:
ezvpn-asa# ping 172.16.100.1
...
ezvpn-asa# show crypto ipsec sa
interface: outside
Crypto map tag: _vpnc_cm, seq num: 10, local addr: 172.16.100.2
[code]....
If I connect a client with IP address 192.168.1.2 to the interface eth0/1 and do a ping to the cme, I don't see any packets getting encrypted. I don't have any idea about VPN, I just need it for a wireless lab environment. What do I have to configure on the ASA, so the inside traffic is encrypted?
View 2 Replies
View Related
Apr 2, 2013
configured 2 EzVPN groups using a 2811 router, i am trying to do this but is not working i have another VPN working thru EzVPN but if i try to configure another group for another EzVPN client is not working and the problem is that the debug crypto isakmp say that Apr 3 08:45:25.802: ISAKMP:(1309): phase 2 SA policy not acceptable!
How is that possible? in my understand the EzVPN server will inject the the IKE (phase 1) and IPSec (Phase 2) parameters for the client and that's they dont need to negotiate nothing, is important to say that the EzVPN client is an ASA5505 with onlu DES encryption enabled, 3DES and AES are not available due to licensing reasons.
View 4 Replies
View Related
Feb 16, 2011
I'm trying to advertise the branch LAN subnets via OSPF back to our core.I can create the OSPF adjacency and the ASA is learning routes fine. However it does not appear to be pushing the branch LAN subnets to the connected router. show ospf database reveals they're not in the OSPF database.Here is my routing config, the branches are 10.114.0.0 /16.As an aside, why I need the statics below, they appear to be necessary to reach my LAN subnets behind the EZVPN spoke sites. I would have thought the ASA would learn it automatically as I'm running network-extension mode on the spokes. [code]
View 1 Replies
View Related
