i have a cisco 2691 and i would like to install NME-16ES-1G-P to set up a Voice Lab environment.Is it possible to have 802.3af PoE support for 2691 using the NME-16ES-1G-P updating the AC power supply? Or does any other solution exist to have 802.3af support on 2691?
View 5 RepliesQuestion for you all regarding a NME-16ES-1G-P installed in a 2811. The NME is running a C3750 image (c3750-ipbase-mz.122-35.SE5.bin). I need to upgrade the IOS and an wondering why the download center is pointing me at C3560 images. I downloaded c3560e-ipbasek9-mz.122-58.SE2.bin and it failed and was stuck in a loop booting and resetting over and over.
View 3 Replies View RelatedI am trying to use the password recovery for an NME-16 and am having trouble. I am unable to look at my files in dir to so I can rename them. I can get the switch to bypass the config and come with the switch: prompt, but can not do anything more. I am trying the password recovery guide, but cant get to the text file to rename. I am using a 2811 router.
View 2 Replies View RelatedWe are getting a replacement NME-16ES module shortly. I don't see a console port on these pups. Once installed - how can we add the configuration from the failed NME-16ES?
View 7 Replies View RelatedAcquired a 3875 Router with a NME-16ES-1G-P switching service module recently. I don't know what the passwords are. I reset the router, and gained access to it, but how do I reset the password on the service module?
View 3 Replies View RelatedI've spent the last two days working on this problem and it is killing me! I know the answer has to be something simple, but despite hours of searching and trying different things, I just can't seem to fix it.Essentially, I am going to be installing a Cisco 2691 and use it as the default gateway for a small business. It will be directly connected to a cable modem with a static IP. The other Ethernet interface is going to connect to a 2950 switch with a couple different VLANs.
The problem I'm having is that I can ping anything external from the router itself. From the clients connected to the 2950, I can ping IPs in other VLANs, and I can ping up to the IP of the external interface, but no pings go beyond that.I've set up NAT overload on the router, and when I do a debug ip nat, I see the pings trying to get through with the proper translations, but I still don't receive ICMP replies back.I set up GNS3 to simulate what I'm trying to accomplish (since it emulates a 2691). Attached is a jpg of the topology -- on the right is the "simulated ISP" with 3 loopback networks and one host on a different subnet. The 2691 has a static route to the "Internet" router, and can ping everything attached to the router, including the host. The host (5.5.5.5) can also ping the outside interface of the 2691 (50.50.50.2).
However, the hosts behind the 2691 can't ping past 50.50.50.2. The 192.168.0.x network can be ignored, because that network won't need to access the Internet. But the 10.10.20.x (VLAN 20) and 10.10.30.x (VLAN 30) networks will need to. In the simulation, the hosts are 10.10.20.5 and 30.5. They can ping each other, their default gateways, and the 2691 outside interface (50.50.50.2) but not the other side, the "Internet" router at 50.50.50.1 or beyond.
[code]....
I have 2691 Router conencted to Internet and it is doing Nat.
This connects to 3550A Switch which has connection to 1811W Router.
I setup VPN between 1811W and 3550A.
3550A has connection to 2691 via ospf.
OSPF is running between 1811w and 3550A.
1811
1811w# sh crypto isakmp sa
IPv4 Crypto ISAKMP SA
[Code]....
I have problem auto connect Easy VPN client to Easy VPN server using saved X auth username/password. The ez vpn client is a Cisco 2691 using IOS 12.4.15T7. The config is as follows:
crypto ipsec client ezvpn EZ
connect auto
[code]....
the router keeps prompting me to manually enter username/password. connectivity will work be established after i manually enter the username/password. But this is not what i desired. I need it to connect automatically.
The Ez vpn server is a 7200 running 12.4.22T. Config as follows:
aaa new-model
aaa authentication login USERAUTHEN local
aaa authorization network GROUPAUTHOR local
[code].....
I have router Cisco 2691 and Cisco 7604 and want to play with AutoQoS Cisco feature. But on both there is no such command But why?
View 1 Replies View RelatedMy 2691 Router has already 2 serial cards WIC-1DSU-T1 installed, When i install the 3rd serial card and reboot the router, it detects the 3rd card installed but 3rd card has no light.
When i do sh ver it shows 3 cards installed.
When i install this 3rd serial card to other Router then light shows on card and it works fine
So i am thinking if 2691 Router only supports 2 serial cards?
I was wondering if i can enable url filtering on my 2691 or 2651XM routers so that if someone visits any website i can see that under router logs. right now i am using kiwi syslog that logs the router activities.
View 3 Replies View RelatedWe're starting to share video across our network and would like to setup multicast to conserve at least some of the bandwidth. We have a broad mix of equipment (A Catalyst 6509-E at the core, a combination for Cisco 2691 & 2811 routers, and a whole lot of Catalyst 3500, 3550, 3560 switches at a hundred locations. Where would I begin? Would I need to define routing for the multicast IP addresses (224.0.0.0)? Would I need to setup interfaces & IP networks where each multicast device is located like I would for a new IP subnet?
View 1 Replies View RelatedOn my 2691 Router i see the buffer leak due to syslog
2691Router# sh buffers leak
Header DataArea Pool Size Link Enc Flags Input Output User
650743C4 F200084 Small 0 0 0 0 None None Init
[Code].....
I have 2691 router with following config
line console 0
login local
password xty
When i remove the login local from the line console i connect to console port and press enter it shows router prompt 2691Router> but i am unable to go to enable mode.If i telnet to router then i put username and pw then it goes straight to enable mode.
vty config is
line vty 0 4
exec-timeout 600 0
logging synchronous
login local
length 500
transport input telnet ssh
escape-character 3
Any reasons why i can not go to enable mode by console?
Here is my Lab Setup: 2691 is BGP nei to R4 router and they are not directly connected. 2691 and R4 are in same AS 6500. 2691 Config---router ospf 1 network 3.3.3.3 0.0.0.0 area 0 . Its advertising its loop back IP to OSPF domain.
router bgp 6500
no synchronization
bgp log-neighbor-changes
neighbor 6.6.6.6 remote-as 6500
neighbor 6.6.6.6 update-source Loopback3
[code]...
R4 Router
router ospf 11
log-adjacency-changes
network 6.6.6.6 0.0.0.0 area 0
[ code].....
We can see that 2691 and R4 are BGP neis and 2691 has 200.1.x.x routes in its route table. My question is why from 2691 router i am unable to ping any route learned by BGP from R4?
2691Router# ping 50.1.1.0 Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 50.1.1.0, timeout is 2 seconds:.....Success rate is 0 percent (0/5)2691Router#ping 200.1.2.0 [ code]...
can wireless router support up to 100 user including support network printer
View 1 Replies View RelatedI have confirmed this with TAC and also been told that a NCS MR2 is going to be coming soon and will have support for the 7.0.220.0 code.
View 3 Replies View RelatedI need to monitor SCE8000 alarms, but LMS does not support this product. My other Cisco products are managed by LMS. get visibility of SCE8000?
View 1 Replies View Relatedcan we install the ISO LMS 4.1 directly on a UCS platform?What platform UCS is supported?Do you have install experiences you can share?Is the ISO LMS 4.1 a Linux implementation?
View 6 Replies View RelatedCisco 2960 Optimization
The current software version is as follows:
System image file is "flash:c2960-lanbase-mz.122-35.SE5/
I WOULD LIKE TO KNOW THE UPGRADE PART TO BE ABLE TO ACCOMMPLISH THE FOLLOWING:
1. Deploy IOS Code containing Crypto ( K9 Image) features and reload the device with the new IOS
2. Generate RSA KEY on the network device + domain name.
3.set limit per MAC@to 4
4.set port to be protected instead of shutdown when limit exceeded
5.enable err disable recovery for link-flap events
6. set up required limits for port security settings preserving current NOD exception
7. i would like to know if i need to upgrade the IOS to achieve this. ?
I am not very familiar with the NM-8A/S module. There is a requrement to terminate a 2 MB link on 1 port of this module on a 2620 router. According to my limited knowladge about this interface it doesn't support more than 128 kb/s . if I can configure for 2 Mb
View 3 Replies View RelatedDoes cisco 887 support anyconnect vpn access?
View 1 Replies View RelatedI have a 2651 IOS ver 12.2(8) T5 and I installed an ATM-T1 4T1-IMA WIC, but the router will not recognize it. Do I need a newer IOS or is there a command to have the router recognize this WIC? Currently it is connecvted to our ISP via the serial connection, but they want to go to an ATM protocol for better video performance.
View 6 Replies View RelatedDoes Cisco 861 have EIGRP support?
View 1 Replies View RelatedI am trying to do Leap and Eap-TLS together. How can I write a policy in ACS that would check for identity before choosing the right profile for the request. ACS 5.2 does not support Native eap-tls. I am assuming I will be using Idenity username for Leap and Predefinied Certificate profile identity for eap-tls.
View 1 Replies View RelatedI found following spec in 8510 controller data sheet
Interfaces and Indicators
#• 2 x 10 Gigabit Ethernet interfaces
#• Small Form-Factor Pluggable (SFP) options (only Cisco SFPs supported): SFP-10G-SR
#• LED indicators: Network Link, Diagnostics
#• 1x Service Port: 10/100/1000 Mbps Ethernet (RJ-45)
However, I need Long Range SFP, i.e SFP-10G-LR
I have WLC 520 with software version 5.2.178. Currently we purchased Cisco AIR-LAP1131G access points and tried to join to WLC 520 but it is not joining. My question is WLC 520 will support 1131G access pont or not.?
View 1 Replies View RelatedI got a Cisco 870 router. running C870-ADVSECURITYK9-M), Version 12.4(15)T7, does this support two link from different ISP.
View 2 Replies View Relatedi just came to know Assurance feature license doesn't come for free when upgrading from LMS4.2 or NCS1.1. It has to be purchased. Before buying this license, i would like to know if IPv6 netflow is supported.
View 0 Replies View RelatedWe have 881 routers and are planning on testing out some WAN optimizing hardware, we're told that our router needs to support PBR and WCCP protocols. Will this router handle it?
View 3 Replies View RelatedI am upgrading from 7.0.116.0 to 7.2.110.0 to support the 3602 APs. Is it a different license to upgrade to 7.2.110.0 or can I directly upgrade to 7.2.110.0 without a new license?We currently have a 5508 base license.
View 1 Replies View Relatedwhat is the maximum number of APs supported on Cisco 2504 WLC?According to the Data Sheet it is 75:
[URL]
But according to the config guide it is 50:
[URL]
I believe the correct number is 50, but I just want to be sure.Is this a software limitation?
Need config for a 1760 to support AT&T's ADSL 6meg, I would like to compare it to what I have.
View 2 Replies View Related