I found following spec in 8510 controller data sheet
Interfaces and Indicators
#• 2 x 10 Gigabit Ethernet interfaces
#• Small Form-Factor Pluggable (SFP) options (only Cisco SFPs supported): SFP-10G-SR
#• LED indicators: Network Link, Diagnostics
#• 1x Service Port: 10/100/1000 Mbps Ethernet (RJ-45)
However, I need Long Range SFP, i.e SFP-10G-LR
We have 3 or 4 older sites that connect back to our central site using ATM over 2 T1s. This connection is for both voice and data. Equipment is a 3640 router and 8510 switch. These are our last sites on ATM, and we'd like to move them away from ATM as soon as we can.
Looking at the Cisco documentation, it looks like we could use 3925s at the central site and at each of the remote locations, with VWIC3 cards (we're using VWIC first generation cards now in the 3640s), and use the drop and insert capability to handle voice and data. I had done some setups like this at a previous job... it's been a couple of years, but hopefully I still got the concept. If I've got this correct, what do we need for the connection to the phone system?
Have been struggling with a connectivity issue following a recent power surge from a storm. A BVI from Cisco Catalyst 3600 cannot communicate with our local network.
We have several satellite connections which connect to us via ADSL. From these satellite offices I can talk to the Cisco 3600 we have here at our central office (BVI 10.60.112.1). There is a connection from the ATM port on the Cisco 3600 which goes to an ATM port on a Cisco Catalyst 8510 and there is an Ethernet connection from that 8510 to the core switch on our local network (Catalyst 6509).
Since I can talk to the 3600 without issue, I believe that the issue is the 8510 config.
There are only two ports in use on the 8510.The ATM port on the 3600 is connected to the 8510's ATM0/0/1.The 8510's ATM1/0/0 (622MM) is connected to our local network's core.There is activity on both ports of the 8510, but from the local network I cannot see 10.60.112.1 and from the 3600 I cannot see the core.
The 8510 config looks pretty default, like some things were "lost" during the surge (we had backups of the 3600 and not the 8510). The config goes as follows for the 8500:
[code]....
I have a Cisco 8510msr that is connected back to back with a 7206vxr across a 155Meg connection.I receive lots of Output drops on the 7206vxr interface facing the atm switch. When I do the following command:-
kwdair9#sh atm int atm 1/0Interface ATM1/0:AAL enabled: AAL5 , Maximum VCs: 4096, Current VCCs: 27 Maximum Transmit Channels: 0Max. Datagram Size: 4528PLIM Type: SONET - 155000Kbps, TX clocking: LINECell-payload scrambling: ONsts-stream scrambling: ON797522 input, 881483 output, 203946630 IN fast, 223768062 OUT fast, 0 out dropVBR-NRT : 110288 Avail bw = 44712 <====
I only have 44megConfig. is ACTIVEkwdair9# I only get 44Meg of the available 155Meg.There is no QOS on the router and the only commands I can find that vaguely see that refer to QOS are on the ATM switch:-
atm address 47.0091.8100.0000.0007.0d87.b201.0007.0d87.b201.00atm router pnnino aesa embedded-number left-justifiednode 1 level 56 lowest redistribute atm-static?why this is acting like a DS3 link and not a 155Meg link?
can wireless router support up to 100 user including support network printer
View 1 Replies View RelatedI have confirmed this with TAC and also been told that a NCS MR2 is going to be coming soon and will have support for the 7.0.220.0 code.
View 3 Replies View RelatedI need to monitor SCE8000 alarms, but LMS does not support this product. My other Cisco products are managed by LMS. get visibility of SCE8000?
View 1 Replies View Relatedcan we install the ISO LMS 4.1 directly on a UCS platform?What platform UCS is supported?Do you have install experiences you can share?Is the ISO LMS 4.1 a Linux implementation?
View 6 Replies View RelatedCisco 2960 Optimization
The current software version is as follows:
System image file is "flash:c2960-lanbase-mz.122-35.SE5/
I WOULD LIKE TO KNOW THE UPGRADE PART TO BE ABLE TO ACCOMMPLISH THE FOLLOWING:
1. Deploy IOS Code containing Crypto ( K9 Image) features and reload the device with the new IOS
2. Generate RSA KEY on the network device + domain name.
3.set limit per MAC@to 4
4.set port to be protected instead of shutdown when limit exceeded
5.enable err disable recovery for link-flap events
6. set up required limits for port security settings preserving current NOD exception
7. i would like to know if i need to upgrade the IOS to achieve this. ?
I am not very familiar with the NM-8A/S module. There is a requrement to terminate a 2 MB link on 1 port of this module on a 2620 router. According to my limited knowladge about this interface it doesn't support more than 128 kb/s . if I can configure for 2 Mb
View 3 Replies View RelatedDoes cisco 887 support anyconnect vpn access?
View 1 Replies View RelatedI have a 2651 IOS ver 12.2(8) T5 and I installed an ATM-T1 4T1-IMA WIC, but the router will not recognize it. Do I need a newer IOS or is there a command to have the router recognize this WIC? Currently it is connecvted to our ISP via the serial connection, but they want to go to an ATM protocol for better video performance.
View 6 Replies View RelatedDoes Cisco 861 have EIGRP support?
View 1 Replies View RelatedI am trying to do Leap and Eap-TLS together. How can I write a policy in ACS that would check for identity before choosing the right profile for the request. ACS 5.2 does not support Native eap-tls. I am assuming I will be using Idenity username for Leap and Predefinied Certificate profile identity for eap-tls.
View 1 Replies View RelatedI have WLC 520 with software version 5.2.178. Currently we purchased Cisco AIR-LAP1131G access points and tried to join to WLC 520 but it is not joining. My question is WLC 520 will support 1131G access pont or not.?
View 1 Replies View RelatedI got a Cisco 870 router. running C870-ADVSECURITYK9-M), Version 12.4(15)T7, does this support two link from different ISP.
View 2 Replies View Relatedi just came to know Assurance feature license doesn't come for free when upgrading from LMS4.2 or NCS1.1. It has to be purchased. Before buying this license, i would like to know if IPv6 netflow is supported.
View 0 Replies View RelatedWe have 881 routers and are planning on testing out some WAN optimizing hardware, we're told that our router needs to support PBR and WCCP protocols. Will this router handle it?
View 3 Replies View RelatedI am upgrading from 7.0.116.0 to 7.2.110.0 to support the 3602 APs. Is it a different license to upgrade to 7.2.110.0 or can I directly upgrade to 7.2.110.0 without a new license?We currently have a 5508 base license.
View 1 Replies View Relatedwhat is the maximum number of APs supported on Cisco 2504 WLC?According to the Data Sheet it is 75:
[URL]
But according to the config guide it is 50:
[URL]
I believe the correct number is 50, but I just want to be sure.Is this a software limitation?
Need config for a 1760 to support AT&T's ADSL 6meg, I would like to compare it to what I have.
View 2 Replies View RelatedI would like to have a support on AIR-AP1142N-E-K9 configurations.How I can config this AP?
View 1 Replies View RelatedHow many routes support 7206VXR with NPE-G2?
View 2 Replies View RelatedDoes L2TPV3 will support multicast?
View 3 Replies View RelatedI want to know the number of routes supported by CISCO3825-HSEC/K9(512MB DRAM).
View 2 Replies View RelatedI need to implement IPv6 for ASA VPN. According to the ASA_8.4_cli_cfg.pdf , IPv6 is not supported on ASA IPSEC vpn and remote client vpn. I do not have a ASA 8.4, any way to verify on ASA8.4 whether the crypto command support ipv6 address ? If the crypto command do support ipv6 address then probably there is chance it will work.what i mean is eg. crypto map xxx set peer <ipv6 address| ipv4 addres> able to set ipv6 address.
View 4 Replies View RelatedI have Cisco Prime 4.2 and several 3560X switches. I want to enable energywise on then but after doing the Readiness Assessment they apper like "Hardware not Capable". As far as I know the 3560X do support energywise.
The switches details:
WS-C3560X-48T-S running IOS 15.0(1)SE3 (C3560E-UNIVERSALK9-M).
Does those switches do not support energywise?
Does Cisco ASA 5520 have IPSEC VPN support for Blackberries?
I found the following document:
Supported VPN Platforms, Cisco ASA 5500 Series [URL] The document doesn't say anything about RIM or Blackberries.
The Blackberries have built-in VPN clients where you can select:
Cisco VPN Concentrator 3000 Series
Cisco Secure PIX Firewall VPN
Cisco IOS with Easy VPN Server
The Cisco ASA is not listed there.
Is it possible that using Blackberry with Cisco ASA is not supported?
I have question for you how many clients have recommended be hooked on Cisco AIR-AP1242AG-A-K9 simultaneously.
View 2 Replies View RelatedCan Cisco 3945E support VRF-Lite ?
View 4 Replies View RelatedFor a customer we want to deploy the Cisco ASR 901 and connect them to a E1 unframed connection. However I don't see in the documentation that unframed is described and I was wondering if the Cisco ASR 901 is supporting E1/T1 in unframed mode? [URL]
View 1 Replies View RelatedI've done some tests and it seems that a 7201 supports GETVPN without a VAM, but in the design guide it states that this is needed.Is this needed as the 7201 documentation states that it performs IPSEC encryption in hardware without a VAM.
View 3 Replies View RelatedAny plans to support REP on the 6500 series?We have Sup 720 with MSFC3.
View 1 Replies View Related