Cisco VPN :: ASA 5520 Support For Blackberries?
Jul 18, 2011
Does Cisco ASA 5520 have IPSEC VPN support for Blackberries?
I found the following document:
Supported VPN Platforms, Cisco ASA 5500 Series [URL] The document doesn't say anything about RIM or Blackberries.
The Blackberries have built-in VPN clients where you can select:
Cisco VPN Concentrator 3000 Series
Cisco Secure PIX Firewall VPN
Cisco IOS with Easy VPN Server
The Cisco ASA is not listed there.
Is it possible that using Blackberry with Cisco ASA is not supported?
View 1 Replies
ADVERTISEMENT
Jul 10, 2010
There is a discussion of this going back many months in the previous forum. My initial post there has had over 600 views and I see that an IT administrator with 10 BB has the exact same problem. I have replaced my BB 4 times and all of them behaved the same way with this CISCO WAP4410N:
THE PROBLEM: The 4410 drops the WiFi connection to a Bold 9700 BB (using WAP2). I got an old Motorola about 6 years old out and found it works fine with the BB as does most of the public hot spots. This is an issue with the 4410. An IT Admin has found (an posted in the eariler forum) that for some reason the key change is not accomplished when issued by the 4410 but it works for others. The Admin discovered that if he set the timout on the key change to maximum he only has to restart the 4410s every 10 days.
So I have the 4410 for my 5 computers with which it works fine and beside it the old Motorola for the BB.
When I called support about this I was told that "we don't support connections to Blackberry." I hate to have to sell this thing on Ebay and buy another brand becuase of this. Seems that Cisco would fix it.
View 1 Replies
View Related
Oct 9, 2011
We are looking to deploy an ASA 5520, but I need to know if it is possible for it to work in this environment.
We have colo space, with two IP ranges. They provide two network drops, one from each switch connected to different routers. One in which has 4 usable IP's for management purposes. This address range will be used only for remote access to the ASA and VPN into the management VLAN. The management VLAN will have all internal devices such as the switches, etc. The second range is for the servers, of which will be assigned directly to the hosts and the ASA will need to act as just a firewall. I can do this on IOS, but not sure about the ASA.
I need to answer the following questions:
Does the ASA support dual network drops, and would this be a failover port configuration in order for it to work?A management VLAN with outbound internet access only, and VPN/RA capability. NAT will need to be used I'm guessing. Can we have a DMZ VLAN which has defined ports, say 80, 443 and 25 inbound and outbound. I need the hosts to have the public IP assigned to them with no NAT configuration.
I know there are some advantaged to using NAT, but I really can't use it because the applications behind prefer public IP's being assigned to them.
View 23 Replies
View Related
Feb 27, 2011
Due to a cost savings campaign we are trying to use open source as much as possible. Does the ASA 5520 support a product called 'untangle' ?
View 2 Replies
View Related
Jun 29, 2011
Can the ASA 5520's support dynamic IP for site to site VPN
View 1 Replies
View Related
Feb 16, 2011
can wireless router support up to 100 user including support network printer
View 1 Replies
View Related
Nov 2, 2012
We were using ASA-5520-K9 with ASA-SSM-AIP-20-K9 but recently found some hardware problem in our running ASA. Now cisco want to replace with ASA-5520-K8.
View 1 Replies
View Related
Nov 6, 2011
I have confirmed this with TAC and also been told that a NCS MR2 is going to be coming soon and will have support for the 7.0.220.0 code.
View 3 Replies
View Related
Aug 27, 2012
I need to monitor SCE8000 alarms, but LMS does not support this product. My other Cisco products are managed by LMS. get visibility of SCE8000?
View 1 Replies
View Related
Jan 26, 2012
can we install the ISO LMS 4.1 directly on a UCS platform?What platform UCS is supported?Do you have install experiences you can share?Is the ISO LMS 4.1 a Linux implementation?
View 6 Replies
View Related
Dec 9, 2012
Cisco 2960 Optimization
The current software version is as follows:
System image file is "flash:c2960-lanbase-mz.122-35.SE5/
I WOULD LIKE TO KNOW THE UPGRADE PART TO BE ABLE TO ACCOMMPLISH THE FOLLOWING:
1. Deploy IOS Code containing Crypto ( K9 Image) features and reload the device with the new IOS
2. Generate RSA KEY on the network device + domain name.
3.set limit per MAC@to 4
4.set port to be protected instead of shutdown when limit exceeded
5.enable err disable recovery for link-flap events
6. set up required limits for port security settings preserving current NOD exception
7. i would like to know if i need to upgrade the IOS to achieve this. ?
View 1 Replies
View Related
Sep 19, 2012
I am not very familiar with the NM-8A/S module. There is a requrement to terminate a 2 MB link on 1 port of this module on a 2620 router. According to my limited knowladge about this interface it doesn't support more than 128 kb/s . if I can configure for 2 Mb
View 3 Replies
View Related
Feb 12, 2013
Does cisco 887 support anyconnect vpn access?
View 1 Replies
View Related
Sep 28, 2011
I have a 2651 IOS ver 12.2(8) T5 and I installed an ATM-T1 4T1-IMA WIC, but the router will not recognize it. Do I need a newer IOS or is there a command to have the router recognize this WIC? Currently it is connecvted to our ISP via the serial connection, but they want to go to an ATM protocol for better video performance.
View 6 Replies
View Related
Aug 11, 2012
Does Cisco 861 have EIGRP support?
View 1 Replies
View Related
Mar 24, 2012
I am trying to do Leap and Eap-TLS together. How can I write a policy in ACS that would check for identity before choosing the right profile for the request. ACS 5.2 does not support Native eap-tls. I am assuming I will be using Idenity username for Leap and Predefinied Certificate profile identity for eap-tls.
View 1 Replies
View Related
Jun 3, 2013
I found following spec in 8510 controller data sheet
Interfaces and Indicators
#• 2 x 10 Gigabit Ethernet interfaces
#• Small Form-Factor Pluggable (SFP) options (only Cisco SFPs supported): SFP-10G-SR
#• LED indicators: Network Link, Diagnostics
#• 1x Service Port: 10/100/1000 Mbps Ethernet (RJ-45)
However, I need Long Range SFP, i.e SFP-10G-LR
View 6 Replies
View Related
May 1, 2012
I have WLC 520 with software version 5.2.178. Currently we purchased Cisco AIR-LAP1131G access points and tried to join to WLC 520 but it is not joining. My question is WLC 520 will support 1131G access pont or not.?
View 1 Replies
View Related
Dec 20, 2012
I got a Cisco 870 router. running C870-ADVSECURITYK9-M), Version 12.4(15)T7, does this support two link from different ISP.
View 2 Replies
View Related
Jan 9, 2013
i just came to know Assurance feature license doesn't come for free when upgrading from LMS4.2 or NCS1.1. It has to be purchased. Before buying this license, i would like to know if IPv6 netflow is supported.
View 0 Replies
View Related
Oct 18, 2011
We have 881 routers and are planning on testing out some WAN optimizing hardware, we're told that our router needs to support PBR and WCCP protocols. Will this router handle it?
View 3 Replies
View Related
Aug 16, 2012
I am upgrading from 7.0.116.0 to 7.2.110.0 to support the 3602 APs. Is it a different license to upgrade to 7.2.110.0 or can I directly upgrade to 7.2.110.0 without a new license?We currently have a 5508 base license.
View 1 Replies
View Related
Nov 28, 2012
what is the maximum number of APs supported on Cisco 2504 WLC?According to the Data Sheet it is 75:
[URL]
But according to the config guide it is 50:
[URL]
I believe the correct number is 50, but I just want to be sure.Is this a software limitation?
View 8 Replies
View Related
May 5, 2013
Need config for a 1760 to support AT&T's ADSL 6meg, I would like to compare it to what I have.
View 2 Replies
View Related
Oct 14, 2012
I would like to have a support on AIR-AP1142N-E-K9 configurations.How I can config this AP?
View 1 Replies
View Related
Jul 24, 2011
How many routes support 7206VXR with NPE-G2?
View 2 Replies
View Related
Oct 18, 2012
Does L2TPV3 will support multicast?
View 3 Replies
View Related
Jan 23, 2011
I want to know the number of routes supported by CISCO3825-HSEC/K9(512MB DRAM).
View 2 Replies
View Related
May 7, 2011
I need to implement IPv6 for ASA VPN. According to the ASA_8.4_cli_cfg.pdf , IPv6 is not supported on ASA IPSEC vpn and remote client vpn. I do not have a ASA 8.4, any way to verify on ASA8.4 whether the crypto command support ipv6 address ? If the crypto command do support ipv6 address then probably there is chance it will work.what i mean is eg. crypto map xxx set peer <ipv6 address| ipv4 addres> able to set ipv6 address.
View 4 Replies
View Related
Feb 20, 2013
I have Cisco Prime 4.2 and several 3560X switches. I want to enable energywise on then but after doing the Readiness Assessment they apper like "Hardware not Capable". As far as I know the 3560X do support energywise.
The switches details:
WS-C3560X-48T-S running IOS 15.0(1)SE3 (C3560E-UNIVERSALK9-M).
Does those switches do not support energywise?
View 4 Replies
View Related
Nov 1, 2012
I have question for you how many clients have recommended be hooked on Cisco AIR-AP1242AG-A-K9 simultaneously.
View 2 Replies
View Related
Mar 31, 2013
Can Cisco 3945E support VRF-Lite ?
View 4 Replies
View Related
Feb 3, 2013
For a customer we want to deploy the Cisco ASR 901 and connect them to a E1 unframed connection. However I don't see in the documentation that unframed is described and I was wondering if the Cisco ASR 901 is supporting E1/T1 in unframed mode? [URL]
View 1 Replies
View Related
