Cisco :: EZVPN Cannot Get Any Response From Server
Jul 24, 2012I try to set up EZVPN server. I cannot get any response from server.
View 1 Replies
ADVERTISEMENT
Cisco WAN :: 857 EZVPN - Cannot Ping Anything From Remote To Server
Mar 14, 2012We have a VPN using 857 and 877 routers as remote connecting in to a 2800 EZVPN Server.
The VPN is working fine. However, the VPN connections sometimes (after a few hours/days) seem to "freeze". A "show crypt sess" shows the connections as Up/Active, but you can not ping antyhing from remote to server, or visa versa, nor does any traffic flow. I then added a "isakmp keep-alive" on the 2800, which improved the situation a bit, but not as much as I hoped.
On the 877 I then implemented a IP SLA, with Object Tracking and then use a Event Manager to just issue a "clear crypto session" . This solved the problem.
However, what do I do on the 857 ? It does not support Object Tracking or the Event Manager. Is there any other mechanism to monitor and reset these frozen/stale VPN connections automatically ?
Cisco VPN :: EZVPN On Client Offices 2901 Server
Dec 3, 2011I have the following problem on configuring ezvpn for the following situation: 3 different locations - 1 HQ with 2901 server and 2 offices with 861 clients.
Clients connects to HQ, I do traffic between HQ and offices but I cannot ping between offices (ping from 192.168.1.0/24 to 192.168.2.0/24 and vice versa.
The configs:
aaa new-model
!
!
aaa authentication login default local
aaa authentication login vpn_xauth_1 local
[Code]....
Cisco VPN :: Does ASA5505 EzVPN Support Reactive Primary Vpn Server Feature
Nov 24, 2011i am going to configure asa5505 as the azvpn client . and configre primay and secondary vpn server in the list.i find some feature that is support by ios ROUTER ezvpn, not sure it will be support on ASA ezVPN???
will the ezvpn fall back to the primary vpn server , if primary back on line, on ASA? The Reactivate Primary Peer feature allows a default primary peer to be defined. The default primary peer (a server) is one that is considered better than other peers for reasons such as lower cost, shorter distance, or more bandwidth. With this feature configured, if Easy VPN fails over during Phase 1 SA negotiations from the primary peer to the next peer in its backup list, and if the primary peer is again available, the connections with the backup peer are torn down and the connection is again made with the primary peer.
Cisco VPN :: 501 Intra-interface Command And Modifying Encryption Domain On EZVPN Server
Jun 30, 2011If you have a headsite with multiple EZVPN clients (PIX 501 & 515) connected in a star configuration can you have one remote site connect to another remote site using the intra-interface command and modifying the encryption domain on the EZVPN Server?
View 3 Replies View RelatedCisco AAA/Identity/Nac :: ACS 4.2 No Authoritative Response From Any Server
Nov 1, 2010I'm having issue with tacacs server(ACS 4.2), did the following test from the router:
Router1#test aaa group tacacs+ cisco cisco legacyAttempting authentication test to server-group tacacs+ using tacacs+No authoritative response from any server.I can ping the ACS server from this router though.
Cisco VPN :: ACE-4710s To Setup Sticky Entries On Server Response Only
Aug 22, 2012I've been using my pair of ACE-4710s for quite some time and have usually stuck to the Class C Subnet sticky settings, as that's what we migrated from in Windows NLB. In one instance of load balancing I'm trying to create an L4 inspection policy that looks for a certain payload (much like a http header) and would like to persist on this. The problem is that the client portion of the conversation starts with a 'SessionID' of 0, and the server responds with a unique 'SessionID'. If I setup the sticky policy with 'Enable Sticky For Response', I get entries populated in the sticky database, but they all go to the same server as there is a sticky session setup for the SessionID = 0. Is there a way to setup sticky entries on server response only? Currently using ACE DM v4(1.0).
View 10 Replies View RelatedPing Test Failed / DHCP Server But No Response
Jan 28, 2013I connects to the wireless box and has full signal but an exclamation mark is present.I have run some tests and the IPv4 and IPv6 say they have no internet access.I also run a full test and everything passed except the ping test which failed and it said: no response:default gateway response: dhcp server it suggested disabling security firewall but i'm not sure if that's the correct thing to do or even how to do that!
View 7 Replies View RelatedCisco AAA/Identity/Nac :: ACS 5.1 - Can't Contact AD Server Slow TACACS Auth Response
Sep 28, 2011Running ACS 5.1 appliance, and am seeing slow repsonse on TACACS authentications due to the ACS trying to reach overseas AD servers and failing. Is there any way to configure a /etc/host/ file locally on the ACS in order to force the appliance to use specific AD servers for authentication? As I understand the process currently, the ACS appliance will query the top-level domain and get a list of all the AD servers in DNS. In my case, this would include the AD servers overseas that we do not want to use.
View 1 Replies View RelatedCisco VPN :: ASA 5520 - Communicate To EzVPN Client Side Internal IP From Server Side
Mar 13, 2013i configured cisco asa 5520 as cisco ezvpn server and cisco 891 as ezvpn client .the configurtion is working fine.i am using client mode on the ezvpn client side.but my quesion is , is it possible to communicate to ezvpn client side internal ip from the ezvpn server side?and one more thing what is the benefit of network extension mode on the client side and how it will work what are possible changes need to do in the server and the client side.
View 4 Replies View RelatedLinksys Wireless Router :: WRT54GS - Unable To Get Response From Server For Flash
Nov 9, 2011I am trying to recover a WRT54GS v1 router from a bad flash. The power light is blinking and would not accept pings. Since I figured it was already hopeless, I attempted shorting pin 15 and 16 which cause it to start receiveing pings. My problem is it won't accept the tftp flash, I've tried both cmd prompt and auto upgrade utility. Upgrade utility says "Unable to get response from the server" however it is still accepting pings. Cmd prompt TFTP says it can't read from local file. I am using windows XP. Code...
View 3 Replies View RelatedCisco VPN :: EzVPN In 7606S With SPA-IPSEC2-2G?
Aug 23, 2011I'm trying to configure a router 7606S with SPA-IPSEC-2G for EzVPN.I was reading some examples in SPa and 7606 documentation but with the current configuration in our router I don't know how to do it.
The router has the SPA installed in slot 3, interfaces G3/0/0 and G3/0/1. The router has the interface G2/0/0 connected to our provider, and we have the interfaces connected directly to network; ie: not vlans, no trunks, ports configured as IP ports conected directly to network.Where can I find an EzVPN example configuration ?
Cisco VPN :: ASA 5510 - Configuring With EzVPN?
Nov 1, 2012I'm having trouble configuring with EZVPN on ASA5510. EZVPN uses the local LAN as the source IP, now since the EZVPN is configured on the ASA, it will use its local port 2.2.2.1 as the source local LAN. The actual local network is behind a firewall and i need the tunnel to extend to the 10.10.10.10 network. Is there a way to extend the tunnel to use the 10.10.10.10 as the source LAN? How to do it via the GUI?
View 3 Replies View RelatedCisco VPN :: ASA5505 - EzVPN Support
Nov 24, 2011Cisco ASA 5505 50-User Bundle includes 8-port Fast Ethernet switch, 10 IPsec VPN peers, 2 Premium VPN peers, 3DES/AES license
ASA5505-50-BUN-K9. Cisco ASA 5505 Unlimited-User Bundle includes 8-port Fast Ethernet switch, 10 IPsec VPN peers, 2 Premium VPN peers, 3DES/AES license ASA5505-UL-BUN-K9
I think they will support ezvpn, just need confirm .
Cisco VPN :: EZVPN Between 2811 And SR520 Flapping
Mar 31, 2011I am having an issue get an EZVPN working between a 2811 server and a SR520 client. The symptoms are the SR520 makes multiple connection attempts to the 2811. It appears that sometimes these connections are successful and the SR520 is assigned an IP address but then the tunnel will be dropped and a new session will be started. I've attached scrubed configs for both the 2811 and the SR520. One other note, when connecting to the 2811 with a software VPN client, there are no problems, so I think the problem is with the SR520. On the other hand, the SR520 wasn't having any problems until we switched our VPN server from a UC520 to the 2811.
View 3 Replies View RelatedCisco VPN :: 3825 IOS EZVPN Client Timeout
Jul 10, 2011I have a 3825 configured as an EZVPN server with 881 routers as clients. One issue I am seeing is that sessions don't seem to time out, such as when a peer's public IP changes. Show crypto ISAKMP peer shows the same host (using device certificates for authentication) with multiple public IPs establishing sessions. I have ISAKMP keepalives configured on the router.
View 2 Replies View RelatedCisco VPN :: 5580 EZVPN Using RRI And NEM With Fa0/0 And Loop Back0
Mar 29, 2011Our company has a handful of sites that use the EasyVPN technology.On my remote router (Cisco1841) - I add the crypto inside to the FA0/0 and the Loopback0 interface.On the other end my Cisco ASA 5580 - 8.41 code - I have RRI enabled and the tunnel comes up fine.However I only see the static route from the fa0/0 interface on the remote router. I can not figure why I can not see the Loopback0 address?Wondering if this is a limitation or feature not enabled.
I added multiple interfaces on the Cisco 1800 and can see the networks.I run "show crypto ipsec sa" on the Cisco ASA and see the spi encaps/decaps for the loopback, but the SH ROUTE does not show the static route being injected.
Cisco VPN :: 857 / EzVPN Sometimes Ping Only In One Direction Or Interface
Jan 14, 2013I have lots of 857's routers in the field with mostly the latest OS - 12.4(15)T17 making ezVPN connections to a 2951 with 15.1(4)M5.All the 857's have lookback and vlan interfaces similar to :
interface Loopback0
ip address 50.43.8.1 255.255.255.255
ip tcp adjust-mss 1452
end
[code]....
Now lately for some or other reason we have instances where I can ping either the VLAN or the LOOPBACK interface, but not both. Or I have instances where the 2951 can ping all the interfaces on the 857, but the 857 can not ping the 2951. Or I have instances where the 2951 can not ping the 857, but the 857 can ping the 2951.The way I have been fixing this is either to add crypto ipsec client ezvpn SMS_VPN inside to the loopback interface, or if it is there already to remove it. This usually works for a few days, but then suddenly I have to reverse this again. If that does not work then I usually do lots of clear crypt sess and/or clear crypt ipsec client ezvpn on the 857, or clear crypt sess remote 857_ip_address from the 2951 and then suddenly it starts working again.
Cisco VPN :: Client Behind EzVPN Remote (ASA 5505)?
Feb 2, 2012I try to configure a simple EzVPN infrastructure:
EzVPN Server (CISCO2811, hostname cme) < -- > EzVPN Remote (ASA5505, hostname ezvpn-asa) < -- > Client
Attached you find both configuration of the EzVPN server and remote. The tunnel is getting up and if I ping from the ASA to the Router, I see the packets getting encrypted:
ezvpn-asa# ping 172.16.100.1
...
ezvpn-asa# show crypto ipsec sa
interface: outside
Crypto map tag: _vpnc_cm, seq num: 10, local addr: 172.16.100.2
[code]....
If I connect a client with IP address 192.168.1.2 to the interface eth0/1 and do a ping to the cme, I don't see any packets getting encrypted. I don't have any idea about VPN, I just need it for a wireless lab environment. What do I have to configure on the ASA, so the inside traffic is encrypted?
Cisco VPN :: Configure 2 EzVPN Groups On 2811?
Apr 2, 2013configured 2 EzVPN groups using a 2811 router, i am trying to do this but is not working i have another VPN working thru EzVPN but if i try to configure another group for another EzVPN client is not working and the problem is that the debug crypto isakmp say that Apr 3 08:45:25.802: ISAKMP:(1309): phase 2 SA policy not acceptable!
How is that possible? in my understand the EzVPN server will inject the the IKE (phase 1) and IPSec (Phase 2) parameters for the client and that's they dont need to negotiate nothing, is important to say that the EzVPN client is an ASA5505 with onlu DES encryption enabled, 3DES and AES are not available due to licensing reasons.
Cisco :: Get ASA To Advertise EZVPN Connected Networks Via OSPF
Feb 16, 2011I'm trying to advertise the branch LAN subnets via OSPF back to our core.I can create the OSPF adjacency and the ASA is learning routes fine. However it does not appear to be pushing the branch LAN subnets to the connected router. show ospf database reveals they're not in the OSPF database.Here is my routing config, the branches are 10.114.0.0 /16.As an aside, why I need the statics below, they appear to be necessary to reach my LAN subnets behind the EZVPN spoke sites. I would have thought the ASA would learn it automatically as I'm running network-extension mode on the spokes. [code]
View 1 Replies View RelatedCisco VPN :: Cannot Access Remote LAN On EZVPN With DVTI 1841
Mar 18, 2011 configured Ezvpn Server/client with client mode configuration on IOS router with ver advipservicesk9-mz.124-15.T3.bin of ISR 1841 routers. Only my main issue is that once the tunnel is up I cant access the server side local LAN. However I could each site my icmp traffic is encrypt or decrypt but not both at the same time. However I can ping from the server to the client ip address which is assigned by the pool (int loopback10000)
Also once the tunnel is up I could also see there's static route towards the client side via virtual-access interface and also static route on client side. I have already configure SPLIT ACL on server side allowing the required network access.Attached is the configuration of both server and client with all required show output.
Cisco Firewall :: ASA 5505 8.4.4 Stops Using EzVPN After Configuration
Sep 24, 2012I've got some ASA5505 which run as EzVPN clients in NEM, connecting to a ASA5510 as head-end. The ASAs are configured with a CSM and AUS. But whenever they are getting a new configuration through the AUS they stop trying to establish an EzVPN connection to the head-end. After a "reload" they run with the new configuration and establish the tunnel as expected.
View 1 Replies View RelatedCisco VPN :: 2911 Remote Office With Dual ISP And EZVPN
Aug 9, 2011I am attempting to get a solid setup for a remote office we have going up and I am running into little issues that I cant seem to get around.
Basically, we have a remote office that will have dual ISPs, one hard wired circuit from a local carrier and the other will be a Verizon 4G router that plugs in via Ethernet and hands out DHCP to my Cisco router.The Cisco router is a 2911 with IP SLA configured. I have it setup to ping my DC out one interface and if that fails, it removes the default route and injects a new default route from the other ISP,
The problem I am having is with the VPN. I figured using EZVPN would be the only solution because the Verizon 4G only supports DHCP so I have to be able to connect from a dynamic remote host. The other caveat is that failover needs to be seamless as we have no person onsite that can troubleshoot. Its fine if it takes a few minutes, but the VPN just needs to come back up on its own without any intervention.
I attempted to setup two different EZVPN crypto maps on the router but realized you can only have one inside cryptomap per interface, which would cause a problem with the internal network. I thought I could just create subinterfaces off the router to have two inside interfaces to work with but that wouldnt have supported because they would now be on different subnets.
I decided that adding an ASA5505 behind the router may be the simplest solution. Use the router only for the purpose of handling routing between the two ISPs and performing NAT out the interfaces. Then use the ASA to do EZVPN from. This works well but there are some issues I am trying to work through.
First, when the ISP fails over to the backup, the NAT translations have to timeout before things start working again. For a constant ping, this is fine, I have the timers set down to 15 seconds for NAT timeouts and after 15 seconds the ping picks right back up again. However, this breaks the EZVPN. The ASA keeps trying to bring up the ISAKMP nearly every second, which keeps resetting the countdown on the NAT timeout for the remote EZVPN server. Because of this, the VPN will never come up until I manually clear the NAT translations on the router. So my first question is this; is there a way to adjust the timer that the VPN uses to try to bring the tunnel up? I tried the crypto isakmp keepalive command but that didnt work, it looks like it doesnt work with EZVPN.
The second issue is really with the IP SLA and is only an issue because of the first issue I mentioned. When the router first comes up after a reboot, both the primary and secondary interfaces come up. However, since the primary default route is only injected into the routing table once IP SLA is up and can reach its destination, the secondary route gets injected initially and the VPN comes up over the secondary ISP. In a few seconds, the primary default route is injected, changes the path and because of the NAT translation, breaks the tunnel and never comes up again because of the first issue with the VPN tunnel renewing the NAT translation continuously.
I could easily go out and purchase a $100 Linksys router that will do the failover and clear its NATs and everything, but I need better reliability out of the hardware than that. There has got to be a way to do this on a Cisco device since consumer level equipment can.
Cisco VPN :: 2800 - EzVPN And DmVPN On Same Router / Interface
Jan 20, 2012I have setup DMVPN and EAZYVPN on one router. Tunnel interface on Spoke one and Spoke two are up/up and show crypto ISakmp sa shows both tunnels are in idle. However, tunnel to Spoke one(10.10.1.1) keep bouncing on and off(see below). Every 30 sec or so, the tunnel gone back to IKE phase while tunnel for spoke two(5.5.5.1) still leave active. THe configuration on the HUB side is the same for both spoke!! show crypto ipsec sec shows both side has the same life time(IOS default). Could that be an IOS debug on the spoke one?
Hub :
Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 15.1(3)T2, RELEASE SOFTWARE (fc1)
HUB#sh crypto ipsec security-association
Security association lifetime: 4608000 kilobytes/3600 seconds
Spoke one:
Cisco IOS Software, C2600 Software (C2600-ADVSECURITYK9-M), Version 12.4(8), RELEASE SOFTWARE (fc1)
[code]....
Cisco VPN :: ASA 5520 - Traffic Not Routing Between Remotes Using EzVPN With NEM
Jun 27, 2012I have ezVPN configured on an ASA 5520 for my server with 5505s as my clients at several remote sites. The tunnels come up no problem and I can hit everything I need to on both sides of the tunnel, but I'm not able to get to another remote network from a remote network. The traffic goes out the tunnel on the 5505 but on the 5520 all I see is a bunch of scrolling tear down messages.
[code]....
Cisco VPN :: 2691 - EzVPN With XAuth Auto Connect
Nov 17, 2008I have problem auto connect Easy VPN client to Easy VPN server using saved X auth username/password. The ez vpn client is a Cisco 2691 using IOS 12.4.15T7. The config is as follows:
crypto ipsec client ezvpn EZ
connect auto
[code]....
the router keeps prompting me to manually enter username/password. connectivity will work be established after i manually enter the username/password. But this is not what i desired. I need it to connect automatically.
The Ez vpn server is a 7200 running 12.4.22T. Config as follows:
aaa new-model
aaa authentication login USERAUTHEN local
aaa authorization network GROUPAUTHOR local
[code].....
Cisco Firewall :: ASA5510 - Routing From EzVPN Client To Non-LAN Zone
Feb 24, 2013I got a Problem with Routing on a ASA5510.
I have ezVPN Clients connected to the ASA5510. Those Clients are assigned an IP from 192.168.236.0/24 Pool.
I have a Router of a contractor connected to a dedicated ASA Interface called IBIZA with IP Net 10.100.10.0/24 and the Router itself with the IP 10.100.10.1. Behind that Router is another private Network which I need to reach from the ezVPN Clients.
The Connection from the ezVPN Clients to the "LAN" Interface/Network on the ASA works fine, but I cannot reach either the Contractor Router (10.100.10.1) nor the Network behind that.
From the LAN Network (on the LAN Interface) I can reach both the Contractor Router and the Network behind.
When I use the Packet Tracer Tool from the ASDM it tells me that the Traffic goes through but ends on the LAN Interface. But it should end on the IBIZA Interface or am I wrong here ?
What do I need to tell the ASA to route the Traffic from the ezVPN Client to the Contractor Router and back ? I have set up the ezVPN Connection as full-tunnel so all Traffic goes through the VPN Tunnel. That shouldn´t be the Problem.
No Response From External IP?
Aug 21, 2012I use Comcast, and am trying to set up an FTP server that I can access from outside my home network. I need the external IP address for that to work, and I have gotten this IP address from IPChicken. I can ping it from the internal network just fine, but when I'm connected to a different network (I've tried two), I get no response, using both the IP address and the associated host name. Of course, I also cannot log into FTP.
I spoke with Comcast support, and their advice was to enable MAC filtering and add the external IP address to it..
Cisco Wireless :: Can't Get Response From AP1232AGs
Sep 2, 2010We purchased 4 AP1232AG access points, intending to use 1 as a router and the other 3 as repeaters. We've spent the past week running power to the repeater locations, installing poles and NEMA boxes, lightning arrestors and 12db antennas. That part went very smoothly.
Now I'm trying to access the APs for the first time and get no response. Cisco states that all the units are set to 10.0.0.1 and that I need to use a console cable from my com port to the console port of the AP. Did that. It also states to use a telnet session to assign an IP, using the setup recommended.
The APs will not respond whether I try a telent, serial or web session. The router center light on all the units is blinking green, which according to Cisco means they are set to the factory 10.0.0.1 and that the radios are disabled. Since it's occurring with all of the routers, I've definitely realized that the problem is operator error. I don't have enough experience to determine where my mistake is being made. I used Indigo to try and reach the routers and the Cisco IPSU as well with no success. I've even tried pinging the router's IP and get no response.
I feel certain that I'm simply overlooking some fundamental and basic task to reach the routers to configure them, but I've been to every technical document on the Cisco site regarding the access and configuration of these routers. I simply can't see my error and it seems like the more I read the bulletins, the less clear it becomes. I'm now stuck.
Cisco :: WLC4400 Http No Response
May 26, 2012My WLC 4400 have run the os 4.2.207.54, my ap type is AP1020.And client user authentication by web-auth.Sometimes my user complain cannot login web authentication, because he connot open the web login page.And I try to monitor the WLC by SNMP, I see the http no response.
View 1 Replies View RelatedCisco Firewall :: No Response From ASA5510
Apr 24, 2012We have an ASA5510 and I am getting absolutely no response from the console port. Not even a blip when I turn it on. If I leave the compact flash in the internal bay, I get Green Power, Amber Status, Amber Active and Green VPN when I start it up. The Flash LED flashes Green twice then goes out. If I move the compact flash to the external bay, all of the other lights remain the same as described above but the Flash LED goes to steady Green. How ever, there is still no response whatsoever from the console port. Have replaced the DIMM but that had no effect. This is a four (4) slot ASA5510 and I have just the one DIMM in slot P13 as described on a post I found. The power supply fan comes on as well as the two (2) fans that cool the heatsink. The other two (2) fans on the expansion module side do not come on.
View 1 Replies View RelatedCisco Router / Ping Not Working - No Response?
Mar 20, 2013I have the following LAN setup: I am trying to ping the Wireless Access point (10.60.1.1) from the Cisco Router (172.16.88.21) but I am not getting responces. I can however ping 10.60.1.1 from server (172.16.88.36). Tracert from the server shows that it is going through the Rotuer and Firewall.
View 8 Replies View Related
