Cisco VPN :: 857 / EzVPN Sometimes Ping Only In One Direction Or Interface
Jan 14, 2013
I have lots of 857's routers in the field with mostly the latest OS - 12.4(15)T17 making ezVPN connections to a 2951 with 15.1(4)M5.All the 857's have lookback and vlan interfaces similar to :
interface Loopback0
ip address 50.43.8.1 255.255.255.255
ip tcp adjust-mss 1452
end
[code]....
Now lately for some or other reason we have instances where I can ping either the VLAN or the LOOPBACK interface, but not both. Or I have instances where the 2951 can ping all the interfaces on the 857, but the 857 can not ping the 2951. Or I have instances where the 2951 can not ping the 857, but the 857 can ping the 2951.The way I have been fixing this is either to add crypto ipsec client ezvpn SMS_VPN inside to the loopback interface, or if it is there already to remove it. This usually works for a few days, but then suddenly I have to reverse this again. If that does not work then I usually do lots of clear crypt sess and/or clear crypt ipsec client ezvpn on the 857, or clear crypt sess remote 857_ip_address from the 2951 and then suddenly it starts working again.
View 1 Replies
ADVERTISEMENT
Aug 2, 2012
I have a IPSec tunnel that is working in one direction. Below is the router config from the side that can connect to the other side perfectly. I believe the issue is with this router as while I was waiting on delivery for the ASA I had an SRP527W sitting in it's place and had exactly the same problem.On one side I have a 887VA router and the other an ASA5505.The network behind the 887VA can access the remote site perfectly, backup services are traversing the link as are web interfaces for applications. In the other direction I can ping hosts but cannot connect. What else is interesting is if from the remote site I attempt to connect to a particular device that performs a port redirect the remote site browser gets so far as being redirected to port 5000 but then hangs.
I am seeing some very generic packet drop debug notices on the 887va on the NAT-ACL access list but I think this is as it should be as it is dropping the tunnel traffic from the NAT'ing.The config for the router is here, I will post the ASA config when I get to the other site shortly but I am convinced the issues is on this device, all the crypto configurations match.I have looked at the MTU's on each side, the path MTU on both sides is 1492. The asa does say the media MTU is 1500 but I believe that is the ADSL link so shouldnt matter?I even went so far as installing CCP and testing the VPN. It says the tunnel is up. It did state a failure:A ping with data size of this VPN interface MTU size and 'Do not Fragment' bit set to the other end VPN device is failing. This may happen if there is a lesser MTU network which drops the 'Do not fragment' packets. [code]
View 1 Replies
View Related
Mar 14, 2012
We have a VPN using 857 and 877 routers as remote connecting in to a 2800 EZVPN Server.
The VPN is working fine. However, the VPN connections sometimes (after a few hours/days) seem to "freeze". A "show crypt sess" shows the connections as Up/Active, but you can not ping antyhing from remote to server, or visa versa, nor does any traffic flow. I then added a "isakmp keep-alive" on the 2800, which improved the situation a bit, but not as much as I hoped.
On the 877 I then implemented a IP SLA, with Object Tracking and then use a Event Manager to just issue a "clear crypto session" . This solved the problem.
However, what do I do on the 857 ? It does not support Object Tracking or the Event Manager. Is there any other mechanism to monitor and reset these frozen/stale VPN connections automatically ?
View 5 Replies
View Related
Jan 20, 2012
I have setup DMVPN and EAZYVPN on one router. Tunnel interface on Spoke one and Spoke two are up/up and show crypto ISakmp sa shows both tunnels are in idle. However, tunnel to Spoke one(10.10.1.1) keep bouncing on and off(see below). Every 30 sec or so, the tunnel gone back to IKE phase while tunnel for spoke two(5.5.5.1) still leave active. THe configuration on the HUB side is the same for both spoke!! show crypto ipsec sec shows both side has the same life time(IOS default). Could that be an IOS debug on the spoke one?
Hub :
Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 15.1(3)T2, RELEASE SOFTWARE (fc1)
HUB#sh crypto ipsec security-association
Security association lifetime: 4608000 kilobytes/3600 seconds
Spoke one:
Cisco IOS Software, C2600 Software (C2600-ADVSECURITYK9-M), Version 12.4(8), RELEASE SOFTWARE (fc1)
[code]....
View 1 Replies
View Related
Nov 15, 2012
I have 1x Cisco 6509 with Sup2 and MSFC2 and it is running on IOS (c6k222-jk9sv-mz.122-17d.SXB11). I have following policy map :
Policy Map VOIP
Class IP PHONE
priority percent 75
and the following command on each interface: service-policy output VOIP those configuration are working fine on SUP2 with MSFC2 but last week I tried to upgrade the SUP2 to SUP32 on the switch and upgrade the IOS to the latest version (s3223-adventerprisek9-mz.122-33.SXJ4) but when I try to put service-policy output VOIP on each physical interface I am getting the following error:
"Priority command is not supported in output direction for this interface" and when I try to add service-policy output VOIP on a V LAN interface I am getting following error:
MQC features are not supported in output direction for this interface. Will I need to change something after upgrading to SUP32..
View 3 Replies
View Related
Jun 30, 2011
If you have a headsite with multiple EZVPN clients (PIX 501 & 515) connected in a star configuration can you have one remote site connect to another remote site using the intra-interface command and modifying the encryption domain on the EZVPN Server?
View 3 Replies
View Related
Mar 31, 2012
I have a new 3560G to set up a small network for a remote site. I configured the vlan and an SVI as the gateway. The switch is also the DHCP server for the LAN. I configured Gi0/2 as L3 port, connecting to the nearest neighbor. My network runs EIGRP so i advertised the routes into the EIGRP process. The switch forms EIGRP neighbors and learns all routes in the enterprise network. The problems I'm having now are: 1. The switch learns all routes in my enterprise LAN and can ping devices in the enterprise LAN, but I can’t ping any interface on the switch from the enterprise LAN. 2.
View 5 Replies
View Related
May 1, 2012
I have a Cisco ASA 5505 and I have my internal and external interfaces configured but I currently cannot ping from the inside to an IP Address on the outside. I had this setup and working and I have another set of equirement that I am replacing that is working with my service provider so I know it is a configuration issue. When I ping 4.2.2.2 for example I get:
Destination host unreachable
Do I need to add a static route from my inside interface to my outside interfaces?
: Saved
:
ASA Version 8.2(5)
!
hostname pxasa
[Code].....
View 2 Replies
View Related
Dec 11, 2010
I've configured a lot vpn server for 857/1800, etc. But this has never happened.I configured 881 as VPN server using CP.Shared key, local group and local user authetication with split route.Local pool 192.168.100.1-254? I have acl for telnet which allows local pool IPs.I have acl to deny local network to local pool IPs for NAT.I've deleted the whole settings and re-run the wizard. It's still the same thing. I can connect from the VPN Client, but no traffic going through. The problem to me is isakmp with DPD. But why it is dead? Why no response from the server? If it is an error, why connection has no problem.
View 1 Replies
View Related
May 12, 2013
I have a cisco ASR 1002 I have plugged a host into an addressed port and the port comes up however the host cannot ping the router and the router cannot ping the host. Neither can router ping its self. I do the same on a cisco 2800 router and it works fine. What's goin on. Is it the fact that this is a ASR router ?
View 5 Replies
View Related
May 27, 2012
I have configured eigrp routing on cisco 1941 ISR with two interfaces advertised. However i can not ping the router interface on g 0/0 but can ping the device and computers attached to that network. When i ping from the same network i'm able to ping the interface but not from anyway else. i can also ping the other devices on other network from g 0/0 attached hosts. How can i enable ping to this interface so that i start monitoring the network?
Below i have attached the network configurations for the router;
!boot-start-markerboot-end-marker!!enable secret 5 xxxxxxxxxxx!no aaa new-model!no ipv6 cefip source-routeip cef!!!!!multilink bundle-name authenticated!crypto pki token default removal timeout 0!!license udi pid
[Code].....
View 3 Replies
View Related
Sep 19, 2012
I have recently installed an ASA5510 at a site in South Africa to connect via VPN to a site in the UK (ASA5520). The VPN comes up fine with the 5520 in the UK, however, I can not connect to the inside interface over the VPN, but can access it from the internal LAN. All other hosts on the LAN are accessible over the VPN.
The 5510 also has another VPN to another site in SA and the 2nd site cannot ping the interface either.
View 10 Replies
View Related
Feb 3, 2013
I cannot seem to ping from the outside of my 5520 firewall to an inside network. I have a single physical outside interface connected to a Layer 2 switch, with a laptop connected to it. This is on network 10.11.131.0/28. From there, I cannot ping to the inside interface (which is a sub interface on G0/0) with network 10.11.130.0/24/ For some reason, it doesnt work.
Now. I had access-lists in place, but have removed them for testing and it still doesnt work. I have set the security level of inside and outside to 100, and entered the same-security-traffic permit inter-interface command - still no joy. Below is the relevant configuration.
Inside Interface
interface GigabitEthernet0/0.96
description L3 Interface - Informational Zone
vlan 96
[Code].....
View 4 Replies
View Related
Mar 19, 2013
I've had some issues with my 892 router. [code] When match address is set to acl-net12, I can't ping my router on external interface and tunnel is working very bad (15%-20% packet loss).If I change match address from acl-net12 to acl-net12-new then I can ping my router on external interface and vpn si working fine.
I have also an acl (set on external interface) which allow ping but it seems that is not working when acl-net12 is used on crypto map. [code]
View 6 Replies
View Related
Nov 14, 2011
I have a Cisco ASA 5505, the problem is I am not able to ping to outside natted interface (ip: 172.88.188.123 and 124 and 125) from inside network I have looked for ASA documentation through the internet and still got nothing.
the config are:
: Saved
:
ASA Version 8.2(1)
!
[Code].....
View 2 Replies
View Related
Feb 7, 2012
I have one problem doing a ping to a router lan interface, I have 3 routers (2801) connected between each other (separated 1 mile each), the link is established trough microwave signals (connected to the 2801 fast ethernet interfaces), every router has a connection to a LAN. One of them is located at headquarters.Last thursday I replace one of the router with a cisco 2901, i configure the router with the same configuration that was on the 2801, i power up the router and the 2 link were up without problems.One day after the noc called me to tell me that after i replace the router they can't ping the router IP lan interface on the new 2901 (before the replacement the ping was sucessful). I called one user the lan connected to that 2901, and they can do a ping to the router's LAN IP address.
I can ping the 2901 IP wan interfaces, I can ping the LAN users ip address, but i cannot ping the router LAN IP address, from my desktop, and neither the 2 routers 2801 connected to the 2901.I show the configuration on the 2901, I couldn't change it because i didn't have time to do that, but i'll change the configuration to use ipsec tunnels.The configuration as you can see, has a crypto map, but the acl used by the crypto map, only permits the interfaces ip address, so i think that doesn't work, so the traffic doesn't get encrypted, but i don't know if that is the problem why i can't do a ping to the lan interface. [code]
View 5 Replies
View Related
Aug 9, 2012
I'm trying to set up a Guest VLAN for wireless at a client site, and I feel like I'm missing something small in the configuration, since I can't ping any of the VLAN interfaces from my laptop when the address is statically set to something in the 172.20.100.x range.
I've pasted the configs for the ASA 5505 and the 6 switches below for convenience. Near as I can tell, all should be well. The ports are in trunking mode, the "show cdp neighbors" command returns the proper information, VLAN 100 exists on all the switches, etc.
Code:
ASA Version 7.2(4)
!
hostname ASA
domain-name xxxx.local
enable password Cj3LF.ehxXN3xVkxWcxd encrypted
passwd Cj3LF.ehxXN3xVkWcxd encrypted
[Code] ......
View 17 Replies
View Related
Mar 13, 2012
We have configure a L2L vpn between Asa and 1841 router. We are facing this issue.The tunnel is not getting up from the 1841 site never. When we are trying to generate traffic from the ASA site the tunnel is up and we can see decryps and encryps packets.
Router 1841 Config:
crypto isakmp policy 100
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp key * address 213.249.XX.XX
[code].....
View 4 Replies
View Related
Jan 16, 2012
I'm using a couple of ASA5510's since a few years in a few datacenters, and I wonder about the following:
Usually the ASA's are positioned with the connectors facing to the back of the 19" cabinets, so one can easily connect the device to other networking-hardware. In many datacenters nowadays, cold-coridors are used, which results in a forced airflow through the cabinet, which is empowered by the fans in the servers itself. But the ASA's are permanently blowing air in the opposite direction, and are also taking the air from the part of the cabinet where the air is as hot as it gets.
Is it a good practice to open up the ASA and flip the fans 180 degrees to solve this?
View 3 Replies
View Related
May 10, 2011
I have a new ASA 5505 and all is working fine, I can CLI and ASDM into it, but just can't ping the inside interface, do I need to enable a feature to make this work somehow?
View 1 Replies
View Related
Oct 22, 2012
I have been working on figuring out a VPN problem on my companies ASA5510. I was accessing the device via: ASDM, SSH using Putty, and even initially with a console cable (also using Putty) using a computer in the networking closet. All 3 of these access methods worked properly for me.I believe I may have inadvertently changed something as of Friday using ASDM. I am mostly assuming this because, as of yesterday I can no longer connect to the device. I actually cannot even communicate with it (ping the interface I normally use to manage, which I could previously ping). No computer on the same subnet as me is able to ping the interface. The device is still accepting VPN connections, dishing out DHCP addresses and everything else it normally does, but I really need to be able to gain access to it again. I am thinking to reboot the device when there is some downtime, in the hopes that ASDM doesn't save to startup-config and only to running-config.
View 5 Replies
View Related
Aug 4, 2011
I'm currently configuring an ASA5510.I connected a laptop (IP 192.168.96.18/255.255.255.0) to port 0/2 and tried to ping 192.168.100.2 ... impossible to ping outside interface.I resetted the config of the ASA to retest more simple. [code]
View 1 Replies
View Related
Apr 13, 2013
I ran into a very strange icmp ping issue. The network has been working fine other than the issue listed below, L2L VPN works fine and all three data centers can access each other via L2L VPN.I have three ASA5510. [code]
View 5 Replies
View Related
Feb 24, 2013
What would cause an interface to show up/up (looped), but you still can't ping that loop?...It is on a Cisco 7613 with an Enhanced FlexWan (WS-X6582- 2PA), with a Mx Serial PA, 8 ports (73-1580-10) and running IOS ver 12.2(33)SRE2 [code]
View 5 Replies
View Related
Dec 12, 2011
I have an ASA 5505 that I'm trying to set up a guest network on. I've configured an interface as a trunk and allowed the 2 vlans but I'm not getting any layer 3 to it. The switch connected to it is a 3560 and port is configured as a trunk with the same vlans.
I can't ping the ASA inside interface but I see its MAC address in the swtich's table.
[code]....
View 4 Replies
View Related
Apr 4, 2012
The ASA is configured in very simple transparent mode. As desired, traffic can flow in each direction between inside and outside. I can manage the ASA via console and direct connection to the management interface. The problem is that I cannot ping or ssh to the ASA via the inside interface. I need to be able to manage the ASA from any PC on the inside LAN. I suspect I am missing some easy aspect of the configuration but after a lot of hours I'm about at the end of my patience with it. Here is what I believe to be the relevant parts of the config.
ASA Version 8.2(1)
!
firewall transparent
hostname issr1
enable password 2alej83t5cqT0FWd encrypted
passwd 4kleUY438I93.4ljdh encrypted
names
[code]....
View 4 Replies
View Related
Nov 5, 2012
So I have a client with an ASA 5520 running version 9.0 (was on 8.4) that I am trying to get either IPSec or SSL VPN configured on. I got everything setup and tried to connect. However, I couldn't connect to either. I fired up the real time monitoring and didn't see any syslog messages referring to a VPN build up. I also enabled SSH/Telnet on the outside interface and cannot connect to the ASA outside interface. I can ping the outside interface and can ping the internet from the ASA. I did set up a test ACL on the ASA and ran packet tracer on it and the results came back fine.
There is an IPS in the ASA as well, but I disabled the ACL for that and still am having these issues. Part of me wonders if the ISP has something set up to block inbound traffic. This should be a business class connection.
View 5 Replies
View Related
Oct 4, 2011
The is VLAN id setting in some network/LAN interface .... how can I ping this lan/network interface in XP ..any freeware can do it ???
View 1 Replies
View Related
Aug 19, 2012
I have to replace a 1230 with an 1262 AP.
All antennas have to be in the same direction on the AP and I guess when the old 1230 is working well the 1262 will be only better . Attached u see how I plan to mount the new AP versus the old one...
View 7 Replies
View Related
Jun 5, 2012
I'm very new to cisco devices but we recently acquired a catalyst 2911 device for our co-lo cabinet and I am trying to get a site-to-site vpn connection working between the facility and my offices network as well as a remote access VPN for me to use in case I have to fix something while outside of the office.
The office's gateway is 66.119.163.2 and the device is a TZ210 with it's LAN network being 192.168.1.0 /24
The co-los gateway is 204.244.50.254 and the device is an ASR 2911 with it's LAN network being 10.0.10.0 /24
The S2S VPN connection is up between the two locations and the 2911 device and the servers within it's LAN can ping and RDP to the office's machines. The office network can only ping the LAN interface IP on the 2911 which is 10.0.10.1 but not the servers in the network. the site-to-site VPN was set up with the CCP wizard.
How can I allow the 192.168.1.0/24 network to see the 10.0.10.1/24 network and why do I only currently see the gateway?
If need be I can post my running-config file with the preshare keys redacted.
View 8 Replies
View Related
Jan 9, 2013
I just barely put in a Cisco 3925 on our network. I've configured gigabitethernet 0/2 to live on our management VLAN with an IP address of 10.129.0.31/16. I did a "no shut" on the interface. Everything should be ready to allow me to ping and/or SSH to that interface but I can't. It's really weird because I've done this a thousand times (at least on ASAs). I must be missing something. At any rate, the default gateway of the management VLAN is 10.129.0.1. I can ping that from the router. I can also ping that from my laptop (which lives on a completely different VLAN). But I can't ping the router from my laptop or vice versa.
Building configuration...
Current configuration : 1360 bytes
!
! Last configuration change at 19:05:13 UTC Thu Jan 10 2013
!
[Code].....
View 4 Replies
View Related
Feb 2, 2013
From the router I can ping the 2nd router, all its host and all of the 1941w interfaces.
From the 1941w AP i cannot reach the 2nd router or any of its host, but I can reach the interface that is connected to the 2nd router but only one side of it.
Attached are both my router and ap configs. At the moment I am just trying to reach the 2nd router and its host so I can update the AP IOS image but cannot reach the tftp server.
View 5 Replies
View Related
Nov 27, 2012
One of my client has BSNL leased line with LAN IP POOL we configured those on ASA 5510 nad Internet working fine but from cloud we are not getting any response for ping requiest please find running configuration below:
ciscoasa(config)# sh run
: Saved
:
ASA Version 8.2(1)
[Code]....
View 4 Replies
View Related
