Cisco Routers :: RVS4000 Distribute A Search Domain In Addition To IP Address / DNS Server Information
Feb 29, 2012
I have just installed and configured a new RVS4000 with VPN (currently running firmware V2.0.0.3), and have enabled the DHCP Server service. I wanted to be able to distribute a search domain in addition to the IP address and DNS Server information (as I have done with other devices that include a DHCP Server), but cannot seem to locate where or how I might do that with the RVS4000.
View 4 Replies
ADVERTISEMENT
Feb 10, 2011
I am having trouble adding a computer to the Domain Controller. I have a cable modem running into a di-524 router. The router has DHCP and DNS relay disabled. I set the LAN IP Address of the router to 192.168.2.1. The router is connected to a switch with 10 pc's and a server running 2003. The server has an IP Address of 192.168.2.2. I setup a DHCP server inside 2003 with a scope of 192.168.2.100-192.168.2.199. Under scope options the router is set to 192.168.2.1 and DNS Servers is set to 192.168.2.2 (the ip address of the domain controller). When I try to add the computer it cannot contact the domain controller. Is there something wrong with my DHCP config or DNS?
View 3 Replies
View Related
Oct 25, 2012
I have a n750 and I did the firmware update on the router and I have it check for firmware updates when I log in and i keep getting this message: "Cannot connect to the firmware information server,please double check the WAN connection." I have access to the internet.
View 14 Replies
View Related
Nov 25, 2012
I have configured PPTP Server on RV042, and created 3 accounts. I am able to connect from Windows PC without any problems.
In the router's logging utility, there doesn't appear to be any log entries indicating either successful or failed attempts to connect to PPTP server. The only access logs I see are for access to the router's configuration utility. Is there a way to view PPTP access in the router system log?
View 4 Replies
View Related
Aug 1, 2012
I just tried replacing a cheap domestic router/switch with an RVS4000 V2 on our work network. This has a WAN connection to a cable modem for internet access via a dynamic IP address.
When I first connected the RVS4000 it got a WAN ip address via DHCP of 192.168.100.11. This is the type of IP address we get when there is an upstream problem with our ISPs cable network, and sure enough we had no internet access. The RVS4000 was set to use DHCP on the WAN interface. So I logged a support call with our ISP but they said there were no problems at their end.
I then swapped the RVS4000 out for the original router. This worked fine and got a WAN DHCP address of 77.xxx.yyy.zzz as it should. Swapped back to the RVS4000 and back to the same problem of getting a 192.168... address.
So, I downloaded the latest firmware from Cisco, which was V2.0.3.2 and flashed the RVS4000.
I then tried again connecting the RVS4000 to the cable modem but this time it would not get any WAN DHCP address at all. On the Status/Gateway page of the web interface it said that the WAN interface was down. However, on the front panel there was a yellow light indicating a live connection on the internet port.
View 1 Replies
View Related
Jun 6, 2011
I have purchased a domain name through a registrar. I currently have a hyper v lab set up at home with a domain controller/dns server and am thinking of starting a web server on either Apache or IIS on a different virtual machine. I want to point my domain name to my home web server.What do I do I have to do at my domain name registrar? I have to point a type of dns record to my home server's public IP and maybe vice versa.I have a static IP at home. Do I have to create some DNS records pointing from my domain name registrar to my server at home using my PUBLIC ip address? If possible please provide specifics on which records I should point to my home server PUBLIC ip address and if any DNS changes need to be made within my domain. Also if any records on my home domain (windows ad domain setup)
I seem to be able to find a lot of info on Apache and IIS but not a whole lot of info on how your web domain name registrar relates to your own web server . I'm not really interested on IIS or Apache specifics but more interested in the fundamentals of how a domain name registrar (GoDaddy, or any other registrar/host) needs to be pointed to your web server and vice versa. I know a lot of people on forums tend to point to links or tell me to go to google but I find it hard to learn that way.
View 3 Replies
View Related
Dec 27, 2012
I read somewhere that the security log could be set to display web address vs dns address. How do i adjust this?
View 1 Replies
View Related
Aug 16, 2011
RVS4000 router doesnt give out an IP address to a client connecting with QVPN v1.303 (or v1.4..- tried that too), connection seems good, router logs the connection and tracks its duration etc but client side does not get an IP from the RVS4000 side -keeps local LAN ip + there is no access to the remote shares etc. RVS 4000 has DHCP enabled. Client side subnet is different to the VPN side. VPN users are setup correctly (Router logs the user as connected) . Port 443 is not setup in port forwarding. (posted in LAN Routing & Switching 2 days ago but I got no response so I thought Id try here !)
View 3 Replies
View Related
Nov 29, 2011
Basically I have a group of static public IPs and I need one of them to point to an internal server IP address. This is for the RVS4000 router.
View 3 Replies
View Related
Dec 28, 2012
I have a Belkin Play N600 as my primary and have an older Belkin G+MiMO that I'd like to connect as an access point only. Any step by step instructions of how to accomplish this?
View 1 Replies
View Related
May 4, 2010
I have a DIR-601 and I'm trying to play the IOQuake3 game Urban Terror (UT). Every time I try to get a list of servers the DIR-601 stops and reboots.What is that? Flood protection? Something else?
View 4 Replies
View Related
Feb 28, 2011
Is it possible to assign public IP address as Router's local IP address (RVL200, RVS4000)?
View 1 Replies
View Related
Jan 17, 2013
Why the below configuration does not work? BGP exchanges routes without a problem all the time the distribute list is removed from the config. When I apply the distribute list it blocks all routes, not just those intended in the prefix list.
[CODE]....
View 2 Replies
View Related
Feb 3, 2011
A site identifies its user through IP address and cookies. My question is about IP address. Does a IP address contain information information about your geographic region? What do those digits in IP address mean? Some websites could tell where the user is located, how?
View 1 Replies
View Related
Feb 21, 2013
Im sitting with a few cisco sf-300 24 switches and i'm trying to get the Mac-addresses the switch have learned from each computer connected to the switch.
View 2 Replies
View Related
Jan 10, 2013
i've been using a VPN to connect to my home network from elsewhere for a few months. It's set up as follows:
PPTP
Maximum Strength Encryption
EAP-MSCHAP-v2 Authentication
Now I find out that MSCHAPv2 authentication has been broken and is no longer considered secure (even by Microsoft), so I want to change the protocol I'm using to make it secure.
However, I've spent 3 hours now researching this and I cannot for the life of me figure out how to use a better protocol on my Windows Server 2012 home server. I've tried setting up PEAP authentication (still PPTP) a la Microsoft's recommendation document, but it requires a certificate. I've created a self-signed certificate but it seems I can't issue certificates (via this method) without being a member of a domain, so I'm stuck. I can't even get started with L2TP since I can't find the option for it.
My question is this: Is there a way to setup a secure VPN server using Windows Server 2012 without a domain? If so, how do I do this?
View 1 Replies
View Related
Apr 2, 2013
So if the PPTP server is enabled, and "Block MAC address not on the list" is enabled under the DHCP settings, will the PPTP client get an IP address?Similarly, if the PPTP server is enabled and the range of IP addresses configured on the PPTP server screen is outside the IP range of the router due to a subnet mask (like 255.255.225.248 for example), will the IP still be assigned to the PPTP client? If assigned, will that IP have any connectivity to the LAN?
View 1 Replies
View Related
Feb 4, 2013
I have a RVS4000 router with DHCP enabled and in router mode.
The LAN is 192.168.2.x. The RVS4000 static IP address is 192.168.2.8
The router is not the RVS4000 and is at 192.168.2.1
The RVS4000 dhcp is assigning it's clients a default gateway of 192.168.2.8 instead of what I want 192.168.2.1. How can I get the RVS4000's DHCP server to assign another IP address other than its own as the default gateway to its DHCP clients?
View 2 Replies
View Related
May 4, 2013
It took a while of troubleshooting since I've never ran into this problem with my wireless router before. But finally I figured out that my router will not assign the proper DNS server addresses when assigning through DHCP. I upgraded from 2.10.02 and still the same issue.
View 1 Replies
View Related
Sep 6, 2011
How many IP address can handle the DHCP server of the RV0xx Series VPN router? can be configured for more than 250 ip addresses? it is posible to configure the router in order to have more than 250 ip address?
View 2 Replies
View Related
May 5, 2013
I'm trying to view the logs from a Cisco 857W router to a workstation running the Kiwi Syslog server. what I've done is the following:
Config term
Logging on
Logging source-interface BVI1
Logging Facility Local7 (or any other facility you want to allocate for this router.)
Logging [IP Address or Hostname of machine running Kiwi Syslog Server]
End
I see noting on the syslog server. Although I can see the log information on the router Also is there a command to stop the logging from generating or is this on by default.
View 1 Replies
View Related
Mar 17, 2011
I am using 2 vpn-routers RVS4000, to interconnect 2 hybrid telephone IP-PBX. After configuring the VPN the head offices are not seen in network. The VPN is active in windows.
IP-PBX works correctly in te same LAN. I understand that the problem is that I do not find how to indicate the router to send de UDP packets to the correct IP thought the VPN.
View 1 Replies
View Related
Mar 28, 2012
I was trying to set a DHCP pool with 127.16.0.0/16 with RV220W, however, RV220W UI can't save it. It displays "IP Address Range -"Step to reproduce: (it is 100% reproducible)
1. login into RV220W admin web
2. Create a VLAN, id 201
3. Go to "Multiple VLAN subnets", select the VLAN, click edit
4. Enter following info:
IP Address: 172.16.0.1
Subnet Mask: 255.255.0.0
DHCP Mode: DHCP Server
Domain Name: Cisco
Starting IP Address: 172.16.2.100
Ending IP Address: 172.16.10.254
Primary DNS Server: 172.16.0.1
Leave rest of settings with default value.
DNS proxy is enabled
5. Press Save button. The UI shows text "IP Address Range -".
Expected result: RV220W shall save the setting and make use of 172.16.0.0 subnet in IP pool. By the way, the error message "IP Address Range -" seems incompleteI tried same setting on netgear FVS318N (very similar settings to RV220W), it accepts 172.16.0.0/16 as DHCP IP pool and works.RV220W has great feature set meets my needs. Its UI is slow and sometime dashboard freezes, which I can live with comparing to features. But DHCP server IP pool can't be class B is huge limitation to me.
View 1 Replies
View Related
Sep 11, 2011
I have 2 internet connections in my office one via Verizon Fios and another one via the local cable company. On the fios connection I have an RV042 VPN router and on the Cable company connection I have an rvs4000 router, I would like to know if there is a way I can connect the 2 so I can share a printer I have on one of the 2 networks from the other network without using the VPN feature, like via an ethernet cable connected between the 2 and some kind of static route maybe?
View 6 Replies
View Related
Jan 28, 2012
I have a couple of domains and servers. I want to forward my domains to my local IP's. Currently, my domains only forward to my WAN ip and then handled by ports. The problem is that I have a lot of the same applications using the same ports.
How do hosting companies do [URL[ For more clarification, This is kind of what I want to do - Domain.com --> 76.xx.xxx.xx --> 192.168.1.xxx ^My domain^ ^My WAN IP^ ^My LAN IP^
Do I need a DNS server? Do I need a proxy server?
View 9 Replies
View Related
May 26, 2013
In the past a used an RVS4000 as a VPN server for my company, but since I recently moved my company to China I would like to use it for a different purpose if it's possible. What I would like to do is the following:
Use an ADSL router to create a LAN networkConnect my RVS4000 to the ADLS router and use it as a switch instead of a routerUse the RVS4000 to connect to a VPN server abroad over L2TP or PPTP . This would allow me to enjoy the best of 2 worlds:
Enjoy the full broadband speed of the LAN network created by the ADSL router for normal internet useHave a separate wired connection permanently connected to VPN giving access to company email etc... My question is: Is this actually possible?
Can the RVS4000 be used as a switch?When used as a switch, can the RVS4000 still be used a 'VPN receiver'? I'm possible trying to do the impossible, because I would have to have the ADSL router have to act as a DHCP server and disable DHCP on my RVS4000 in which case it is probably impossible to have the RVS4000 act as an L2TP/PPTP VPN receiver.
View 1 Replies
View Related
Aug 9, 2011
RVS4000 router doesnt give out an IP address to a client connecting with QVPN v1.303, connection seems good, router logs the connection and tracks its duration etc but client side does not get an IP from the RVS4000 side -keeps local LAN ip + there is no access to the remote shares etc. RVS 4000 has DHCP enabled. Client side subnet is different to the VPN side. VPN users are setup correctly (Router logs the user as connected) . Port 443 is not setup in port forwarding.
View 3 Replies
View Related
Jan 8, 2012
How do you forward a domain to a sub-net address? I know how to forward to my network address, but I have not been able to find any documentation on the internet on how to forward to a LAN address.
View 2 Replies
View Related
Jan 4, 2013
I can find ip address of any website from domains by using simple command [URL] in command prompt.I wonder how I can find the domain names from ip addresses.For e.g. I would like to know the domain names of ip - 207.232.22.200
View 7 Replies
View Related
Nov 8, 2012
I have a 891 router setup as the local DNS server and external lookups from connected devices (and the router cli) work fine. I'm having problems getting internal host lookups working though.
this is relevent part of the config, router ip address is 192.168.100.9:
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.100.1
[Code]....
If I put rearswitch. (i.e. add a single full stop at the end of the hostname) it resolves fine. The same behaviour happens with other hosts defined with the ip host command. Is it possible to use local hostnames without a domain name or full stop?
View 1 Replies
View Related
Oct 10, 2012
I just wanted to know that can I install LMS 4.0 on a domain server.
View 1 Replies
View Related
Jul 24, 2011
how do I pass from domain server , my network in our compant have ISA server and they close some website like face book , how can I pass over ISA server and use my websites?
View 3 Replies
View Related
May 22, 2012
I do not have wireless internet access and I get the message "There may be a problem with your Domain Name Server (DNS) configuration" when I try to diagnose the problem.I am on the internet by bypassing the router and having a wired connection from the modem to the computer right now. The problem started when I tried to get a second computer to work with the wireless connection (so with the computer I'm on right now, wireless worked a few days ago). [code]
View 9 Replies
View Related
