Cisco Routers :: RV016 PPTP Server And Block MAC Address
Apr 2, 2013
So if the PPTP server is enabled, and "Block MAC address not on the list" is enabled under the DHCP settings, will the PPTP client get an IP address?Similarly, if the PPTP server is enabled and the range of IP addresses configured on the PPTP server screen is outside the IP range of the router due to a subnet mask (like 255.255.225.248 for example), will the IP still be assigned to the PPTP client? If assigned, will that IP have any connectivity to the LAN?
View 1 Replies
ADVERTISEMENT
Sep 12, 2012
I am having problem when try to connect through VPN from MacOS to my RV016 router.The situation is like this. I can connect to the router,the connection is succesfull, but when I try access resources inside the network it disconnects me.The message is "You are dissconnected by the PPTP Server". I encountered this problem on MacOS Snow Leopard and Lion. I tried to connect from 3 different Apple machines, but the problem is the same.
View 1 Replies
View Related
May 15, 2006
Can I configure a PIX (515), as PPTP client to establish a tunnel with non-Cisco PPTP server ? Can my PIX initiate this type of connection ?Today, I use a PC with PPTP client to establish this and I want replace this with a PIX and I don´t want depends of a PC.
View 5 Replies
View Related
Oct 29, 2012
For the past week, I have tried to setup the PPTP VPN server on the RV180. The setup was straight forward, but I could not log-on no matter what I tried. I decided to call Cisco small business support, and as I was talking to the engineer, it mysteriously started to work. I was puzzled and somewhat embarrassed because I'd hate to admit it was an id10t problem on my part. As I tried a few different configurations, I began to realize there might be a limitation in the RV180 PPTP VPN server with the current firmware (1.0.1.9).
In short, the RV180 PPTP only works with 192.168.xxx.xxx/24 subnet. My setup has 3 vlans: vlan1 in 172.xxx.xxx.xxx/24 subnet, vlan2 192.168.0.xxx/24, and vlan3 10.xxx.xxx.xxx/24. My originally plan was to keep vlan3 isolated by disabling inter-vlan routing, but I needed a way to manage a couple of devices on vlan3 remotely, thus I wanted to setup a VPN in the 10.xxx.xxx.xxx/24 subnet. This turned out to be the reason why it never worked before. Today when I called Cisco support, I assigned the PPTP VPN server a 192.168.0.xxx ip range, and it worked. Later, I tried assigning 172.xxx or 10.xxx ip addresses to the PPTP VPN server, and they both failed to work. I created another test vlan4 with 192.168.2.xxx/24 subnet, and assigned the PPTP VPN server to that vlan, and it worked again.
I'd like to mention that I already configured the 10.xxx.xxx.xxx/24 subnet with a few devices before I replaced my router with RV180, and I don't want to have to change and test the setup of all the devices. Another reason I want to have my VPN server outside the 192.168.xxx.xxx range is that it's way too commonly used by wifi hotspots that it increases the chance of wifi and vpn in the same subnet.
I can test a few more configurations, but I think the results will be the same. Perhaps Cisco should test the RV180 in the lab to confirm what I found.
View 2 Replies
View Related
May 5, 2012
I possess a RV220W (firmware 1.0.3.5) but I can't seem to work with the PPTP server on one VLAN only.
My default VLAN is in 192.168.1.1/24. I created a VLAN ID 10 in 192.168.50.1/24 inter-vlan routing : disabled and Device Management : disabled. (Menu Networking > LAN > VLAN Membership and Multiple VLAN Subnets).
Then I configured a PPTP server on the IP range 192.168.50.200 to 192.168.50.210.
To finish I created my user. (Menu VPN > IPSEC > VPN Users).
The PPTP tunnel is working, but on all my local network and not only the VLAN ID 10.
View 3 Replies
View Related
Jan 6, 2013
We have 3 internet links from different providers connected to configured WAN 1,2,3 in RV016. A remote client needs to connect to a internal VPN Server behind RV016, so we use one-to-one NAT to publish the internal server ip to a Valid IP from WAN3 and setup protocol binding in Multi wan to all trafic (TCP and UDP) from the internal VPN address exits with WAN3.
So, the remote client tries to connect to VPN using this ip Address from WAN3 and sometimes work and sometimes not. It's clear to us that the problem lies in the response from RV016 not coming always from WAN3, because if we disconnect the two other links (WAN1 and 2) Its works flawless.
View 3 Replies
View Related
Sep 11, 2011
We have just acquired a Cisco RV120W Firewall Router and we are experiencing issues with this router. I've read some threads related to port forward issue with RV120W before writing this new topic.
We have 2 locations (site A and site B) connected with a Site to Site VPN (PPTP) running under Windows Server 2008 R2 with TMG 2010. This Site to Site VPN worked very well until we replaced our old router with the RV120W at site B. Since this moment, our engineers are not able to make the site to site VPN work again. The TMG box are located just behind the router.
We have followed some threads about Port Forwarding but it did not solve our issue (others port forwarding rules for RDP for example work). Our RV120W is running the last stable firmware (1.0.2.6) provided by Cisco.
View 1 Replies
View Related
Nov 25, 2012
I have configured PPTP Server on RV042, and created 3 accounts. I am able to connect from Windows PC without any problems.
In the router's logging utility, there doesn't appear to be any log entries indicating either successful or failed attempts to connect to PPTP server. The only access logs I see are for access to the router's configuration utility. Is there a way to view PPTP access in the router system log?
View 4 Replies
View Related
Sep 2, 2012
how can i block local server ip address in WAP321?I set captive portal web page and user accounts for guests but I still can map into my local server once the guest account is log in to CP.
View 1 Replies
View Related
Oct 10, 2011
i just want to ask how can i block all proxy server websites in my router( any brand ) so that no one can access, like facebook i already block it in the router but they still access using proxy server website.
View 2 Replies
View Related
Mar 9, 2012
I am trying to configure a Cisco 871 to act as a PPTP VPN server on my home network. I have referenced Cisco's documentation regarding this which I will include below as well as a copy of my current running configuration and terminal monitor information from when I attempt to establish a connection.
When I attempt to connect from a Windows machine I receive the following error: 'Error 807: The network connection between your computer and the VPN server was interrupted.' 'The remote device won't accept the connection.'When I attempt to connect VIA my mobile, I get 'The server has hung up'.The 871 does detect the incoming connection which can be seen from the terminal monitor output: url...
View 2 Replies
View Related
Oct 30, 2012
Ok, so with my WLC2504 implementation, I use the 4 ports to physically segment my wireless networks. Here is my setup:
Port 1 (Management) - Internal IP so I can manage the WLC from our internal network (Untagged)
Port 2 - Connected to our core stack and tagged with VLAN 14
Port 1 and 2 are both connected to the same core stack
Port 3 - Connected to a RV016 Linksys which is connected to our fiber connection to the outside (Untagged) - External connection for laptops
Port 4 - Connected to a Linksys wireless router (with wireless disabled) (Untagged) - External connection for smartphones
The TAC engineer I talked to just told me that I can only have one untagged interface on the WLC. If they are physically connected to different switches, thus physically segmenting the network, should it matter?
The wireless works just fine. What I am having issues with is getting a client that is hard-wire connected to the RV016 to get a DHCP address from the WLC.
View 9 Replies
View Related
Sep 26, 2012
I tried to configure a 1721 router, but he can't connect in my server. I follow various how-to in the Internet.
View 2 Replies
View Related
Feb 10, 2013
I add a new Cisco ASA 5505 as firewall in of company network. I found the PPTP authentication did not get through to internal Microsoft Server.
ASA Version 8.4(3)!names!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1switchport access vlan 2!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1nameif insidesecurity-level 100ip
[Code]....
View 4 Replies
View Related
May 16, 2011
We have a 1941 router configured with LAN/WAN access. Additionally, we need to allow outside Microsoft RRAS connections to an inside Windows 2003 R2 Server. What commands are required to enable this?
WAN IP: 211.XXX.XXX.XXX
Server IP: 10.XXX.XXX.XXX
We've configured the 1941 router to allow outside RDC/RDP to the server at 10.XXX.XXX.XXX
View 1 Replies
View Related
Feb 4, 2013
I have a RVS4000 router with DHCP enabled and in router mode.
The LAN is 192.168.2.x. The RVS4000 static IP address is 192.168.2.8
The router is not the RVS4000 and is at 192.168.2.1
The RVS4000 dhcp is assigning it's clients a default gateway of 192.168.2.8 instead of what I want 192.168.2.1. How can I get the RVS4000's DHCP server to assign another IP address other than its own as the default gateway to its DHCP clients?
View 2 Replies
View Related
Aug 25, 2012
I'm trying to configure 1700 K9 router to act as PPTP client and connect to Microsoft VPN server (in order to enable all clients on LAN to seamlessly access host on remote location). [URL]
I'm using GMS3 to test everything in lab environment. I managed to connect to Microsoft VPN server but the connection drops immediately. Below is debug info from router R1 (router R2 just simulates host on LAN) and configurations for both routers. The only clue I got from debug is that immediately before closing connection there's a message "CCP: Failed to negotiate with peer"...
R1#sh debug
PPP:
PPP detailed event debugging is on
MPPE Packet Details debugging is on
[Code].....
View 2 Replies
View Related
Apr 26, 2011
we are not able to connect to a outside PPTP vpn server;The scenario is this :Connections are started from inside netwok to a VPN server on the outside zone.
I have add these configs and still not working.policy-map global_policy class inspection_defaultinspect pptp ?i also have a acess-list for it.access-list inside_access_in extended permit tcp object inside-network any eq pptp access-list inside_access_in extended permit gre object inside-network any access-group inside_access_in in interface inside? I am missing something or this is all configs i have to get done ?
View 5 Replies
View Related
May 4, 2013
It took a while of troubleshooting since I've never ran into this problem with my wireless router before. But finally I figured out that my router will not assign the proper DNS server addresses when assigning through DHCP. I upgraded from 2.10.02 and still the same issue.
View 1 Replies
View Related
Jan 17, 2013
I setup my Windows 8 desktop for a PPTP VPN server so I can connect my iPhone 5 to it.Using the Cisco Connect Firmware, as I was having internet speed issues with the Smart Wi-Fi Firmware and I wasn't loving the interface of the Smart Wifi Firmware anyway.According to the router the firmware is up to date. All three VPN settings are enabled.PC is set to a static IP internally. 192.168.1.116 to be precise.PPTP port forwarding (1723) is set to the PC's static IP, though I have tried without port forwarding and it didn't work either.If I have my iPhone connected to the wireless network and point it to the internal IP address of the PC, I can connect to the VPN.If I bypass my router and hook my desktop directly to the modem (and point my iPhone to the IP that gets assigned to my desktop from my ISP) I can connect to the VPN.But if I have everything hooked up normally and try to connect to the VPN from my iPhone (using the IP address my ISP assigned to the router), I get a PPTP server not responding error.
View 3 Replies
View Related
Sep 6, 2011
How many IP address can handle the DHCP server of the RV0xx Series VPN router? can be configured for more than 250 ip addresses? it is posible to configure the router in order to have more than 250 ip address?
View 2 Replies
View Related
Jun 7, 2012
how i can configure the Cisco RV042 to access PPTP VPN Server (Witopia VPn) or other vpn servers.
View 1 Replies
View Related
Apr 14, 2011
I have a 2821 ciso router and i want to setup a vpn for my windows domain users , they must to reach the domain from outside. There is posibile to intregrate Active directory auth with pptp running on 2821 router? kind of dialin via radius server(IAS running on windows server 2003).
View 3 Replies
View Related
Jan 24, 2011
I cannot connect to a PPTP on the outside of my network.We have a RV082, port 1723.It says verifying username and password but then disconnects.The error log says Blocked IP Spoofing.
View 1 Replies
View Related
Mar 7, 2012
I am trying to allow PPTP traffic through my Linksys WRT320n to a PPTP VPN server on my home network.The Linksys WRT320n is running firmware 1.0.05 build 002Mar 31, 2011.I have created a Port Forwarding rule on the Linksys to allow TCP & UDP port 1723 through to my internal IP of the PPTP VPN server,but everytime I try to connect with a PPTP client from outside of my network I get a connection error on the client.Checking the PPTP VPN servers logs I see the following errors (Please note all IP's have been masked) Mar 2 11:15:07 ap-01 pptpd[5300]: CTRL: Client x.x.x.x control connection startedMar 2 11:15:07 ap-01 pptpd[5300]: CTRL: Starting call (launching pppd, opening GRE)Mar 2 11:15:07 ap-01 pppd[5301]: pppd 2.4.4 started by root, uid 0Mar 2 11:15:37 ap-01 pppd[5301]: Exit.Mar 2 11:15:37 ap-01 pptpd[5300]: GRE: read(fd=8,buffer=41fe30,len=8196) from PTY failed: status = -1 error = Input/output error, usually caused by unexpected termination of pppd, check option syntax and pppd logsMar 2 11:15:37 ap-01 pptpd[5300]: CTRL: PTY read or GRE write failed (pty,gre)=(8,9)Mar 2 11:15:37 ap-01 pptpd[5300]: CTRL: Reaping child PPP[5301]Mar 2 11:15:37 ap-01 pptpd[5300]: CTRL: Client x.x.x.x control connection finished
From looking at the above errors, it seems as if the Linksys isn't forwarding GRE through to my PPTP server.I have tried various settings, including enabling and disabling the PPTP Passthrough option on the Linksysbut still can't get PPTP to work.What is the correct way to get GRE traffic forwarded through the Linksys?
View 4 Replies
View Related
Feb 29, 2012
I have just installed and configured a new RVS4000 with VPN (currently running firmware V2.0.0.3), and have enabled the DHCP Server service. I wanted to be able to distribute a search domain in addition to the IP address and DNS Server information (as I have done with other devices that include a DHCP Server), but cannot seem to locate where or how I might do that with the RVS4000.
View 4 Replies
View Related
Mar 28, 2012
I was trying to set a DHCP pool with 127.16.0.0/16 with RV220W, however, RV220W UI can't save it. It displays "IP Address Range -"Step to reproduce: (it is 100% reproducible)
1. login into RV220W admin web
2. Create a VLAN, id 201
3. Go to "Multiple VLAN subnets", select the VLAN, click edit
4. Enter following info:
IP Address: 172.16.0.1
Subnet Mask: 255.255.0.0
DHCP Mode: DHCP Server
Domain Name: Cisco
Starting IP Address: 172.16.2.100
Ending IP Address: 172.16.10.254
Primary DNS Server: 172.16.0.1
Leave rest of settings with default value.
DNS proxy is enabled
5. Press Save button. The UI shows text "IP Address Range -".
Expected result: RV220W shall save the setting and make use of 172.16.0.0 subnet in IP pool. By the way, the error message "IP Address Range -" seems incompleteI tried same setting on netgear FVS318N (very similar settings to RV220W), it accepts 172.16.0.0/16 as DHCP IP pool and works.RV220W has great feature set meets my needs. Its UI is slow and sometime dashboard freezes, which I can live with comparing to features. But DHCP server IP pool can't be class B is huge limitation to me.
View 1 Replies
View Related
Jul 19, 2012
I set up a PPTP VPN with an RV220W recently. It was working flawlessly until a recent power outage and now users are getting the 807 error when attempting to connect. I have PPTP passthrough enabled and TCP/UDP 1723 open. As far as I can tell GRE 47 is open as well. Why it was working and is not working after a power outage?
View 2 Replies
View Related
Jun 22, 2011
I am using a RV016 (192.168.1.2) as a router and DHCP. It automatically assigns its own IP which is 192.168.1.2. I can not set my RV016 to assign a Default Gateway IP of the server. The workstations will connect to internet via this server (192.168.1.1)
View 1 Replies
View Related
Jan 27, 2013
I would like to ask if what is the replacement for RV016? Is there any on the ISR G2 that can be set as a mulit-WAN router? Meaning can handle for more than two WAN connections.
View 2 Replies
View Related
Jan 22, 2010
I have a rv016 that's been in 24x7 operation since I bought it a few years back. It is out of warranty. It is connected to three cable modems on WANs 1-3. Behind it are a bunch of PCs getting IPs via DHCP. There is a gateway to gateway vpn tunnel setup on wan3 to a rv082 at another site. There is a forwarding entry for http to an internal http server. Everything else is pretty much default.
The router is primarily used to aggregate bandwidth for uploading large numbers of photos. The systems behind the router initiate the uploads and the router automatically load balances the outgoing bandwidth.
This was all working fine until just recently. The ISP is Knology who is upgrading each of the 8m/768k cable modems to 25m/5m. They are also moving from DOCSIS 1 to DOCSIS 3. They are currently in the middle of this upgrade and have upgraded the modems to DOCSIS 3 as well as the speeds to 12m/2m. The problem is that the rv016 Network Service Detection, which is set to "Default Gateway" indicates that the modems fail randomly. Usually only one will be failed, but up to two will fail the Network Service Detection simultaneously.
Knology insists that there is nothing wrong with their modems. I have removed a modem from the rv016 when Network Service Detection indicates it is in a failed state and connected it directly to a computer. It will work, but it has a different IP address and default gateway. As soon as I connect it back to the rv016, it works there too, but on the original IP address and gateway. I've only tried this test this twice so far, so it is a bit inconclusive.
Speed tests behind the rv016 are the same as directly connected to one of the cable modems. The router works normally as it has for years. Nothing else is acting funny.
So my question is, is the rv016 failing or is the ISP having problems?
View 17 Replies
View Related
Jul 22, 2012
Problems on RV016 the firmware, Firmware Version : v4.2.1.02 (Jan 18 2012 14:10:55) on port PPPoE mode. It makes the dial, but not Web browsing correctly. The solution was to return the old version of firmware.
View 1 Replies
View Related
Nov 22, 2011
I am trying to upgrade my RV016 from 3.0.2.01-tm to 4.0.4.02. I have not received any messages and the log has nothing. I have left the computer and switch for 2 hours and it never seems to end. (serial no. DF0006200812).
View 1 Replies
View Related
