Linksys Wireless Router :: E4200v2 PPTP Server Not Responding
Jan 17, 2013
I setup my Windows 8 desktop for a PPTP VPN server so I can connect my iPhone 5 to it.Using the Cisco Connect Firmware, as I was having internet speed issues with the Smart Wi-Fi Firmware and I wasn't loving the interface of the Smart Wifi Firmware anyway.According to the router the firmware is up to date. All three VPN settings are enabled.PC is set to a static IP internally. 192.168.1.116 to be precise.PPTP port forwarding (1723) is set to the PC's static IP, though I have tried without port forwarding and it didn't work either.If I have my iPhone connected to the wireless network and point it to the internal IP address of the PC, I can connect to the VPN.If I bypass my router and hook my desktop directly to the modem (and point my iPhone to the IP that gets assigned to my desktop from my ISP) I can connect to the VPN.But if I have everything hooked up normally and try to connect to the VPN from my iPhone (using the IP address my ISP assigned to the router), I get a PPTP server not responding error.
View 3 Replies
ADVERTISEMENT
Dec 20, 2012
My ISP dynamicly assigns IP's so I have my New E4200V2 set up as Automatic Configuration DHCP. I want to be ablt to use a specific DNS server rather than the one issues by my ISP.No matter what values are in the Static DNS 1, 2 and 3 the router continues to pull a DNS from my ISp. My POS old D-link 615 was able to utilize a custom DNS server with no issues so surely ther emyst be a way to do the same on the E4200.
View 8 Replies
View Related
Apr 24, 2012
New E4200v2 @ firmware 2.0.36. The FTP server will go offline about once every 24 hours. I can revive it by simply clicking on Save in Storage/Administration or FTP Server. I don't have to change anything, just click Save. How can I keep the FTP running?
"Disk" is a 16gb USB flash memory. Formated FAT32, 1 partition, 6 users besides Admin and Guest, 2 groups besides Admin and Guest.
View 2 Replies
View Related
Mar 25, 2013
Is it possible to change the DLNA Server's name? Cisco49129 just doesn't have a nice ring to it.
View 1 Replies
View Related
Mar 7, 2012
I am trying to allow PPTP traffic through my Linksys WRT320n to a PPTP VPN server on my home network.The Linksys WRT320n is running firmware 1.0.05 build 002Mar 31, 2011.I have created a Port Forwarding rule on the Linksys to allow TCP & UDP port 1723 through to my internal IP of the PPTP VPN server,but everytime I try to connect with a PPTP client from outside of my network I get a connection error on the client.Checking the PPTP VPN servers logs I see the following errors (Please note all IP's have been masked) Mar 2 11:15:07 ap-01 pptpd[5300]: CTRL: Client x.x.x.x control connection startedMar 2 11:15:07 ap-01 pptpd[5300]: CTRL: Starting call (launching pppd, opening GRE)Mar 2 11:15:07 ap-01 pppd[5301]: pppd 2.4.4 started by root, uid 0Mar 2 11:15:37 ap-01 pppd[5301]: Exit.Mar 2 11:15:37 ap-01 pptpd[5300]: GRE: read(fd=8,buffer=41fe30,len=8196) from PTY failed: status = -1 error = Input/output error, usually caused by unexpected termination of pppd, check option syntax and pppd logsMar 2 11:15:37 ap-01 pptpd[5300]: CTRL: PTY read or GRE write failed (pty,gre)=(8,9)Mar 2 11:15:37 ap-01 pptpd[5300]: CTRL: Reaping child PPP[5301]Mar 2 11:15:37 ap-01 pptpd[5300]: CTRL: Client x.x.x.x control connection finished
From looking at the above errors, it seems as if the Linksys isn't forwarding GRE through to my PPTP server.I have tried various settings, including enabling and disabling the PPTP Passthrough option on the Linksysbut still can't get PPTP to work.What is the correct way to get GRE traffic forwarded through the Linksys?
View 4 Replies
View Related
Mar 25, 2012
When I try to stream a movie through the media server or through my computer to my xbox 360 the video will play fine for a couple minutes then it well get choppy and then the sound will not sync with the picture. I have the latest firmware and reset it also. Tried switching channels and changed mtu didn't do anything. tried steaming on 2 different xboxs and its the same thing.
View 3 Replies
View Related
Jan 11, 2012
What new features you would like to have on E4200V2?Here is what I would like to have on it,iTune Server,Torrent Download support,WDS.
View 1 Replies
View Related
Jan 24, 2011
I cannot connect to a PPTP on the outside of my network.We have a RV082, port 1723.It says verifying username and password but then disconnects.The error log says Blocked IP Spoofing.
View 1 Replies
View Related
May 15, 2006
Can I configure a PIX (515), as PPTP client to establish a tunnel with non-Cisco PPTP server ? Can my PIX initiate this type of connection ?Today, I use a PC with PPTP client to establish this and I want replace this with a PIX and I don´t want depends of a PC.
View 5 Replies
View Related
Jun 7, 2012
how i can configure the Cisco RV042 to access PPTP VPN Server (Witopia VPn) or other vpn servers.
View 1 Replies
View Related
May 22, 2012
My internet is hooked via cat6 ethernet cable to my Cisco/linksys E2000 Router.Sometimes the net works fine, and there are no problems. Other times, after 10 minutes or so after booting up, net pages stop loading. The small yellow exclamation mark appears, and every time I run the troubleshooter, the same info comes back to me - DNS server is not responding. Until I restart again the internet wont work, but on occasion things seems to fix themselves and continue working until I shut down.This problem never happened before i moved back home. In my previous apartment we had comcast cable and it ran without a hitch. Since I have been home this DNS problem has persisted, but only on my computer. I run the only windows PC in the house - my family is mac happyThings I have trie - I have tried "netsh winsock reset" in the command prompt, I have run virus and spyware scans several times over, Have reset the modem, router, and the Mac which hosts my 'home network'-come to think of it, I haven't tried reinstalling my LAN driver, but that seems insignificant b/c it has never once had problems.
View 8 Replies
View Related
Mar 20, 2012
Currently i am having a scenario where i have setup RV042 and which is connected to Microsoft Forefront 2010. PPTP works fine only on rv042 subnet but i am not able to access the "internal" network of TMG.RV042 (172.16.1.1) ---> TMG [external] (172.16.1.2) ---> TMG [internal] (192.168.1.1) Is there any way through static route to access the TMG internal network through RV042 pptp server?
View 1 Replies
View Related
Aug 25, 2012
I'm trying to configure 1700 K9 router to act as PPTP client and connect to Microsoft VPN server (in order to enable all clients on LAN to seamlessly access host on remote location). [URL]
I'm using GMS3 to test everything in lab environment. I managed to connect to Microsoft VPN server but the connection drops immediately. Below is debug info from router R1 (router R2 just simulates host on LAN) and configurations for both routers. The only clue I got from debug is that immediately before closing connection there's a message "CCP: Failed to negotiate with peer"...
R1#sh debug
PPP:
PPP detailed event debugging is on
MPPE Packet Details debugging is on
[Code].....
View 2 Replies
View Related
Jun 29, 2012
I think my E4200v2(Firmware Version: 2.0.37 ) should redirect to CCC as this link, is the CCC just could be used in US?
View 4 Replies
View Related
Mar 16, 2012
Recieved this E4200 as a repplacement for a v1 that kept dropping wireless connection. Now after about 1.5 months the router keeps rebooting. Tried resetting, etc...no luck. Calling Cisco now.
View 3 Replies
View Related
Mar 28, 2012
this topic has been discussed under the v1 software and marked as solved yet it has not been. Has anyone attempted with version 2 software and been able to connect after the arp was flushed?
View 6 Replies
View Related
Apr 21, 2012
Just got my new E4200 v2 router. Set up mac filtering for one device and after saving the change the router was refreshing and disconnected all my devices and could not log in to the router wired or wirelessly and had to do a factory reset. Have the latest firmware. Is this a defect in the router?
View 2 Replies
View Related
Dec 23, 2011
I will soon upgrade my wireless network from a WRT610N to an E4200v2. At setup of the router, I assume I'll be able to change the SSID of the E4200v2 and I plan to keep the same SSID as on my old router. With the same SSID as currently seen by the devices on my network
View 4 Replies
View Related
Jun 29, 2012
I have a synology DS411 and a ATV2.DS411 is always downloading from internet,normally the download' bandwidth of DS411 is around 2MB/s.In my old netgear 3800,i just need to active WMM and add a port OQS that the port connection DS411 is low.Then when I watch stream video from internet on my ATV2.I can see the DS411's bandwidth will be reduced automatic.I replaced 3800 with E4200v2 some days before,and I have done the same config ,turn WMM ,set ATV MAC to highest and DS411 MAC to lowest. But when I watch ATV2,DS411's bandwidth seems not be reduced,so I cant get the smooth video Its very bad.
View 9 Replies
View Related
Apr 14, 2011
I have a 2821 ciso router and i want to setup a vpn for my windows domain users , they must to reach the domain from outside. There is posibile to intregrate Active directory auth with pptp running on 2821 router? kind of dialin via radius server(IAS running on windows server 2003).
View 3 Replies
View Related
Feb 29, 2012
We have the Linksys E4200v2 router. We have two servers on our network that we want to access remotely (from outside). We have two Static IPs from our ISP. We currently utilize one of those IPs to access one of the servers-no problem. How can we utilize the second IP to access the second server?
View 3 Replies
View Related
Jan 11, 2013
I have a static IP on the ATA (Linksys PAP-2T) ...the router will only pick it up occasionally...most times it does not. The ATA is on and working (I can call in/out) but I can't see how the router can't find/see it. I have added the ATA to the DHCP reseve list but still nothing. I have the port fowarded for the ATA but when I go to canyouseeme.org it comes up as "Connection timed out"...becuase I think it can't see the ATA behind the Router.
View 1 Replies
View Related
Jan 8, 2012
On the D-Link it was easy, I can see who is connected to which radio.But I can't figure out how to see who is connected to WiFi on hte E4200?I run several access points in my house, and I need to make sure htey are all working.If I can't see who, if any, is connected, I have no idea if WiFi on the E4200 is working.
View 2 Replies
View Related
Dec 14, 2011
V2.0.26.124551 is now available. I did the online upgrade and it took just a couple of minutes including the reboot. The firmware is not available as a download yet for manual install. This firmware is dated 11/14/11 so it doesn't appear to correct the Port 53 issue reported earlier.Release Date: Nov 14, 2011 Firmware version: v2.0.26 (Build 124551) - Support for the WAN L2TP and PPTP protocols
View 1 Replies
View Related
Dec 23, 2011
E4200v2 DMZ does not appear to work correctly?I have two e4200v2 both with latest firmware and it appears to me that the DMZ setting does not work. I continue to have to apply many port forwarding and triggering rules to make needed ports accessible.
View 9 Replies
View Related
Aug 16, 2012
I am wondering what is the optimal way to set-up my E4200v2 and PLWK400 at home? I have several devices (laptops, tablets, phones) that connect on .11g and .11n.
My current set-up:
E4200v2: 5ghz - Wireless-N only (SSID home-n), 2.4ghz - Wireless-B/G only (SSID home-g)
PLWK400: SSID home-ext (separate part of the home)
I am using WPA2 Personal security if that makes a different. One question would it be "better" to have the same SSID for all 3 wireless settings (5ghz, 2.4ghz, and PLWK400)? Would the various devices know which frequency to switch to for best speed and range?
View 6 Replies
View Related
Feb 24, 2013
I tried to upgrade my router firmware to the latest 2.1.39.145204 (downloaded from cisco website) but seems like the upgrade didn't go well. I am unable to open the admin webpage. I can get to the login page on 192.168.1.1, after i enter the admin password the next page doesn't load. It keeps showing 'Waiting' at the center of the page forever.. I have tried to do the 30/30/30 reset to no avail, i tried to do tftp downgrade to older firmware version but the tftp boot doesn't even start. Is there any other way i can either fix the current firmware upgrade or downgrade it to the previous version?
View 9 Replies
View Related
Jan 23, 2012
Where can I download the 2.0.36 firmware?I flashed it through the UI but since the factiry fw is crap I want to try the third party firmware that are available but I want to make sure there is a path back to factory version in case I need to return the product.
View 1 Replies
View Related
Aug 1, 2012
I purchased an e4200v2 to replace my old WRT160n which I have been using for years with no issues. Last night the e4200 crashed on me when I went to reset the router I noticed the CISCO light was blinking very slowly and I had no network connection. I power cycled the router and still no connection so I hit factory reset button. Nothing happened. Did a 30/30/30 reset nothing happened. At this point I have a 34 day old plastic brick on my desk and I'm back to using my old WRT160N. how to unbrick this router?
View 3 Replies
View Related
Jan 31, 2012
No problem setting up the FTP server on the router. It's working perfectly from inside the LAN. But any attempt to access the built-in server from the WAN side is fruitless. I found that if I turn off the IP4 SPI on the router, I can suddenly connect to the built-in ftp server without issue from the Internet. If the SPI option is checked, its a no go.
Is this a bug? I can't imagine that it is intentionally set up such that you have to turn off the firewall in order to use the FTP function externally. At least it isn't mentioned anywhere I can find and it wouldn't seem logical.
View 2 Replies
View Related
Feb 24, 2013
I've had this E4200v2 for a while now, and it's been giving me a headache because even at default wireless setting with the passphrase, it literally won't ever connect from a linksys wireless adapter using the mixed WPA2 Personal or the 'EasyConnect' button feature or the PIN, with both side's fireware updated to the latest. There is no issue connecting to the router as long as the security is off. I've tried other form of encryption to no luck.
View 1 Replies
View Related
Jul 24, 2012
My Linksys E4200v2 router died (no blinking lights when a network cable is attached). Is this a bait and switch?
View 2 Replies
View Related
Feb 11, 2012
I recently changed my wirless router from the E4200 to the E4200v2. As far as I know, I have the same settings on the E4200v2 as I did on the E4200. My PS3 will not connect to my wireless network via the E4200v2. I even retyped in my network information (SSID and password) onto the PS3. Still "no joy." Any issue with the E4200v2 and the PS3?
View 9 Replies
View Related
