Cisco VPN :: RVS4000 As VPN Switch Server?
May 26, 2013
In the past a used an RVS4000 as a VPN server for my company, but since I recently moved my company to China I would like to use it for a different purpose if it's possible. What I would like to do is the following:
Use an ADSL router to create a LAN networkConnect my RVS4000 to the ADLS router and use it as a switch instead of a routerUse the RVS4000 to connect to a VPN server abroad over L2TP or PPTP . This would allow me to enjoy the best of 2 worlds:
Enjoy the full broadband speed of the LAN network created by the ADSL router for normal internet useHave a separate wired connection permanently connected to VPN giving access to company email etc... My question is: Is this actually possible?
Can the RVS4000 be used as a switch?When used as a switch, can the RVS4000 still be used a 'VPN receiver'? I'm possible trying to do the impossible, because I would have to have the ADSL router have to act as a DHCP server and disable DHCP on my RVS4000 in which case it is probably impossible to have the RVS4000 act as an L2TP/PPTP VPN receiver.
View 1 Replies
ADVERTISEMENT
Sep 6, 2012
I have a RVS4000 with client VPNs setup and have created all 5 users......trouble I run into is that when one of the users attempts to connect to the VPN from a second device (ie the sixth device to connect to the VPN), the connection does not establish....cannot ping remote server (using QuickVPN). In looking at the logs, the device that isn't working is getting a different IP (172.16 vs 192.168). I know I'm limited to 5 users, but am I limited to 5 devices as well?
View 2 Replies
View Related
Feb 16, 2013
There are 5 VLAN's and all can communicate through all the different subnets, but VLAN5 can not communicate to the RVS 4000.
VLAN Smart Port set to switch and router - this is not working What Smart Port configuration should be set up to talk to the LAN port on a RVS4000?
VPN is set up and connected, but when trying to connect to the client can not connect to remote networks.
View 1 Replies
View Related
May 3, 2012
I have problem with RVS4000 fw 1.3.3.5. When you switch the status of IPS function (turn on or turn off), firewall rules don´t work from that moment until you restart the router!
View 2 Replies
View Related
Feb 29, 2012
I have just installed and configured a new RVS4000 with VPN (currently running firmware V2.0.0.3), and have enabled the DHCP Server service. I wanted to be able to distribute a search domain in addition to the IP address and DNS Server information (as I have done with other devices that include a DHCP Server), but cannot seem to locate where or how I might do that with the RVS4000.
View 4 Replies
View Related
Apr 3, 2012
I would like to set up "IP SLA" between L3 switch(supports many "IP SLA" versions like "UDP Echo Operation", "TCP Connect Operation", "UDP Based VoIP Operation", "ICMP Echo Operation", "FTP Operation" etc) and GNU/Linux server. Are there any "IP SLA" test types which are supported only between two Cisco devices?
View 1 Replies
View Related
Apr 4, 2012
I'm pondering this new client's topology. He has: (internet) >> router >> switch >> Windows server with a VPN enabled.
Right now I access his network remotely by just RDP directly into the server with a public IP address.Now doesn't this mean that I'm already sailing through his router and switch? Doesn't that mean that all (broadcast, routing, etc) communication hitting this IP is sucking CPU cycles and bandwidth on his router, switch, and server? Wouldn't it be best if he had his VPN endpoint set on his gateway?
View 1 Replies
View Related
Apr 28, 2011
when we use switch as dhcp server and we want to configure a DHCP relay on other subnet that is not connected to this switch, what is the DHCP server ip address for configuration of DHCP relay? Should we use vlan1 ip?
View 2 Replies
View Related
Apr 3, 2011
I have connected two servers to my network. Both servers are running Win 2008 R2 and I have connected as follows.Connected 3Com switch to 2Wire router using Ethernet straight cable. Then connected server to 3Com switch.All lights on switch are green, but still unable to connect to internet.When I connect server to router, internet is working, but not through switch.
View 1 Replies
View Related
Mar 7, 2013
I have some unused 10G NIC's and want to see if there's a way to install them into a computer and turn that PC into a switch. I need to run Windows based software for driver support of the NIC's, such as Server 2012. This is a picture of what I am hoping to accomplish:
[PC1] -----10G------[PC2]------10G------< Hardware Switch >
| | | | |
1G 1G 1G 1G 1G
| | | | |
[PC3][PC4][PC5]......
As you can see in the simplified picture above, I have a real switch which has a single 10G link that is connected to PC2. I would like to add the 10G cards to PC2 so that I can create a "switch" of 10G ports on PC2 which I can then hook up other clients (such as PC1 in the above picture).
PC2 needs to provide network access and internet access to PC1 (and other PC's connected to PC2 - not pictured).
The rest of the clients on the network are connected to the regular gigabit ethernet ports of the hardware switch (including my router which is 192.168.1.1).
I looked into Windows Internet Sharing, but for that to work, I need to connect the router to PC2 above and for other considerations not described above, it is not physically possible for me to do that.
Is there software I can run on PC2 that will turn all the NIC ports of PC2 into a "switch"?
View 7 Replies
View Related
Jul 21, 2011
pxe server ip address is 10.10.10.20 which is connected to switch port fa0/9 and client is connected to switchport fa0/7.i have only 3 devices altogether. below is running config of switch. wen i boot the client from the server, it display error message as: "proxy dhcp were offered. none dhcp were received. exiting broadcom pxe."
Switch#sh run
Building configuration...
Current configuration : 2710 bytes
!
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption[code].....
View 1 Replies
View Related
Sep 9, 2012
How about supporting an scp server on the switch? Makes life much easier for collecting configs and pushing OS upgrades.
View 1 Replies
View Related
Feb 23, 2012
I am sutdying at uni and in a few months, I will be moving into a house, with my current flatmates. We will be buying a fibre optic line.Ideally,what I want to do, is split the connections evenly,depending on how many people are online current, rather than having mass downloads of everyone at the same time, when other will only get a small speed while browsing or gaming,or streaming,etc.So, basically, what I want to do is split the connection at anyone time evenly,so if there are 5 people connected and our connection speed is 50MB then each will get 10MB. And if 2 people are connected, then the speed will be 25MB each, and so on.
I am wondering what is the cheapest way of doing this? I am very computer illerate,I know how to use unix systems.I even own my own server, but I'm not so clued up in this area of networking.I believe it's something to do with a switch, and which switches support this? (I've heard it's something to do with full-duplex / half duplex).
- I will probably set up a domain system, where everyone has to login to the main server to access the internet. (I know vaguely how to do that) - is there some software that I can put on the server which will distribute connection speeds automatically.
View 6 Replies
View Related
Apr 8, 2013
I'm due to replace a stack of 2 x 3750 switches very soon with 2 x 3750Gs. These 2 current switches are the VTP server for a small domain. I have put the config on the new switches switches and I made it a server and used the same VTP domain and password etc and got the VLAN info ported over.Now I did this a while back and noticed the switches are in transparent mode with a revision number of 0, I need to set this back to server and swap the switches out but the revision will be lower than the client switches (around rev 200), what do I need to do?
View 7 Replies
View Related
Jan 23, 2012
Have you ever found the problem that if I set two tacacs server in my N7K and the primary tacacs server fail, won't switch over to another tacacs server.
View 1 Replies
View Related
Apr 13, 2011
I can authenticate between our MDS 9216i switch and RSA radius server but my role does not come across. The logged in user is a network-operator not admin. In the AV Pair i have defined shell:role*network-admin but it doesnt seem to come across
View 4 Replies
View Related
Jan 8, 2012
I have a 1250 AP connected to an Switch Cisco 3750. We have a SSID(v lan 1 - native) which get an IP Address from our DHCP Server(located in a Windows 2003 server). I added a new SSID in VLAN 2 and I would like no to use the DHCP Server but to make the AP get an IP Address from the pool I created in the own AP (ip dhcp pool Guest) but every time I try to connect the new v lan, it doesn't get an ip address.
Follow the settings of the AP.
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[Code]...
View 10 Replies
View Related
Apr 17, 2013
I want to replace an existing 3560 Switch with another switch of the same exact model and IOS. However, this switch that needs to be replaced is the VTP Server of my LAN at this location. When I replace the switch I will just use the same exact running config but I'm concerned about the vlan.dat file. Do I need to copy that file over to the new replacement switch and if so, what is the best way to do that?
View 5 Replies
View Related
Sep 28, 2011
Just installed a RV042 with dual wan connections. Would like to make the WAN 2 (new cable modem as well) the primary connection over WAN1 (DSL), however whenever I switch from WAN1 to WAN2 in Smark Link set up, our email server will not send mail out, even though nothing is blocking the connection.
View 0 Replies
View Related
Sep 11, 2011
just want to confirm if I could use the 2x 10GE uplink ports of a cisco 2960 to connect to my Server directly?
View 17 Replies
View Related
May 27, 2010
I have a 3750 switch stack running version 12.2(53)SE2 IPBASEK9-M. I have dot1x configured on the switch and have a Windows 7 PC connected with 802.1x configured on the interface. I see the EAPoL start message from the PC, but I don't see any RADIUS packets from the switch to the RADIUS server. I have a simple dot1x config just to try to get it working prior to adding additional features such as guest-vlan...
Config and debug file attached.
I don't know if the ip dhcp snooping and arp inspection configuration is causing an issue with this or not. I see the EAPoL packet received on the switch as seen in the debug attachment, but I still never see the RADIUS packet. I did set both to trust on the interface but still the same outcome. I can't disable it since it is a production switch with a test interface.
View 5 Replies
View Related
Apr 26, 2012
I'm attempting to configure a Catalyst 3560-X Switch to act as a DHCP Server. There is documentation that supports this feature. Below is my config procedure however after the completed procedue no IPs are handed out to clients. [code]
View 1 Replies
View Related
Aug 13, 2012
'm able to setup my 3750e switch to login through a radius server with my company user id and password but would like to be able to set it up that when I log in it drops me on the enable prompt. Right now I have to type >en.Then the enable password.
View 1 Replies
View Related
Jul 15, 2012
My Name is senthil i need to configure new hp sever with Nexus 5548 how to config.. server side everything finished just i need only
Config tips for Nexus 5k for New server
View 2 Replies
View Related
Apr 22, 2012
I have a switch(6500) with 2 vlans(2 SUBNETS) and from the other side of my network i have 2 terminal servers.
I want to have a VIP in my 6500 switch which i have the 2 vlans and when the first vlan(network) try to connect to the VIP
my switch will forward to first terminal.When the second vlan try to connect to VIP the switch will forward to second terminal.
I'd like the switch to decide in wich terminal server will forwared the packet based on source network.
I am not sure how i can do this???I use VIP with SLB???I use NAT???PBR?
View 4 Replies
View Related
Feb 8, 2013
How to configure SF300 48port switch as DHCP Server or not.
My Configuration as below
I have 8 vlan configure in SF300 (SVI with ip address) isit possible to configure dhcp server and how i can apply access-list to restrict with other vlans.
View 6 Replies
View Related
Aug 23, 2011
How to configure SF300 48port switch as DHCP Server or not.
My Configuration as below
I have 8 vlan configure in SF300 (SVI with ip address)isit possible to configure dhcp server and how i can apply access-list to restrict with other vlans.
View 1 Replies
View Related
Feb 24, 2013
I have a Netgear DG470N gigabit modem and I am streaming 1080P films from a 2TB networked hard drive onto a LG 42inch Smart TV viat wired ethernet. Sometimes the films crash and the TV cannot reopen the network folder with the film in until a reset is done on the modem. Is there a high speed gigabit switch that I can use to improve this or should I get some media controlling software?
View 3 Replies
View Related
Feb 11, 2012
With out using any server, will DHCP be configured in cisco 2950/2960 switch?I man cisco it self should work as a dhcp server also.
View 10 Replies
View Related
Apr 29, 2013
I am trying to copy IOS from my TFTP server which is on my laptop to cisco 2960 switch
I am able to ping to switch from my laptop, connectivity is fine, tftp server is running
Current Image on Switch --> C2960-LANBASE-MZ.122-25.SEE3.bin --> trying to upgrade to --> c2960-lanbasek9-mz.122-53.SE2
I am getting below error when trying to upgarde IOS:
2960-SW#copy tftp: flash:
Address or name of remote host []? 10.1.x.x
Source filename []? c2960-lanbasek9-mz.122-53.SE2
[Code].....
View 6 Replies
View Related
Jun 24, 2012
I need to configure a Cisco 2960 switch as a DHCP server. The current IP address will be on a different seed than the DHCP addresses. i.e.
Switch IP = 10.1.2.3, GW = 10.1.2.1, Subnet = 255.255.255.0
DHCP addresses would be 192.168.1.1 - 200, GW=???? (10.1.2.3?) and subnet would be 255.255.255.0
View 1 Replies
View Related
Jun 24, 2012
I'm trying to connect Switch 3560 to NTP Server based on Linux, the NTP is working fine but the switch is sync with the Server:
address ref clock st when poll reach delay offset disp
*~10.0.0.70 208.53.158.34 3 42 64 377 1.7 -2.49 0.1
* master (synced), # master (unsynced), + selected, - candidate, ~ configured
Clock is synchronized, stratum 4, reference is 10.0.0.70
nominal freq is 119.2092 Hz, actual freq is 119.2093 Hz, precision is 2**18
[code].....
But server has on time and the Switch another. I test this NTP with CUCM and is working fine, the issue is with ther server?
View 9 Replies
View Related
Apr 16, 2013
I have installed a switch (3560) that was from another site and changed all it's config and hostname etc and it is now live, however the syslog messages still see the old hostname, what could be causing this?
View 3 Replies
View Related
