Cisco Firewall :: Testing 5515x At Home - No Internet Route
Apr 15, 2013im new to cisco asa and the model is 5515x with license plus. below is my config at home,
ciscoasa#
ciscoasa# sh run
: Saved
[Code]......
ADVERTISEMENT
Cisco Firewall :: 5515x Apply On Firewall / Switches To Make Implementation Successful
Apr 22, 2013I will be implementing a new firewall (cisco asa 5515x) on my existing 3750x (server switches) and my 2960s (user switches). What should I need to apply on my firewall and swtiches to make the implementation successfull. I will put my 3750x as my DMZ and my 2960s as my inside. The 3750x have multiple subnet and also the 2960s.which features and technologies i need to know on those 3 products. my 3750x and 2960s don't have any ACL defined and most common features are vlan, switchport, trunking, spanning-tree, stacking, vtp.how my asa knows that my 3750x/2960s have multiple vlans. my current connection right now on 3750x and 2960s is just through 6 ports i assigned as one trunk, below is my config [code]
my 2960s vlans are almost the same with my 3750x except vlan 160, 170, 192. but of course when i put this in asa, i have to segragate vlan for 3750x (192, 100, 110,160, 170) and 2960s (130, 150). for my 2960s connection to the asa and since this will have big bandwidth, i will use 3 ports on my asa (and trunk it) connecting to my 2960s and i will use 2 ports on my asa (and trunk it) connecting to my 3750x. the one internet ports and my one management ports on my asa will stay like that.
Cisco Firewall :: ASA 5515X - Config Loss After Primary Firewall Reloaded
Sep 23, 2012I have a strange issue which happened to me last weekend with two ASA 5515X on version 8.6(1)2. There was a planned power shutdown which only affected the primary firewall. Failover was configured and running successfully. The configuration was also saved after every change made. After power was shut and primary firewall went off the secondary took over like it should but unfortunately all configuration was gone. We immediately powered on the primary again but also this one lost the configuration.
While reconfiguring the firewall we ran into another problem. The devices won't pair although it was the correct configuration. After three times removing and adding the same failover configuration the devices accepted the failover and worked together again.
I went through the bug toolkit and white papers regarding ASA 5515x and this particular version but were not able to find anything.
Cisco Switching/Routing :: 2900 - Testing Home Connection Qos VPN Phone?
Jan 18, 2012I have asked to test an VPN phone for home Users. I have a BT adsl broadband at home which is going into a cisco 2900 switch. Port One is connect to the computer port 3 is connected to the Avaya VPN phone this work's. The quality is not very good, so the question is could I have qos on Port 3 which is connected to the phone?
View 4 Replies View RelatedHome Network :: Getting A Wireless Router Emulator For Software Testing?
May 29, 2011I have developing a utility which lets a user do the following :-
1)Identify the internet gateway device / router using uPnP
2)Check for the portmappings present in the gateway
3)Add / remove a port mapping from the gateway device
4)some other functions like loopback interface testing etc
Now , I need a router simulator (or any other way )which supports the following to test my work uPnP+ NAT +can be configured using SOAP XML messages although this is not a requisite as I am using Microsoft's SDK for uPnP ?Host 3 (or may be 4 is the RAM allows) virtual machines , connect them into a subnetwork using this software and then testing for the above requirements .
Cisco Firewall :: Upgrade From 8.2 To 8.6 For New ASA 5515X
Sep 19, 2012My customer has a rather complex configuration on an ASA 5510 running version 8.2.
They are migrating to new ASA 5515X models which of course only version support 8.6
How can i convert the configuration from 8.2 to 8.6 since the new ASA's do not support the earlier versions?
The X series seems to be a great option for new deployments but what about replacements of existing older models?
Cisco Firewall :: ASA 5515X 8.6 IOS For NAT Control
Feb 21, 2013I am in a process of replacing the Cisco ASA 5510 with 7.3 OS with a new Cisco ASA 5515X with 8.6OS. In the existing Cisco ASA 5510, we have configured 'no nat-control' for which the traffic from all sub-interfaces were flowing to the lower security interfaces without any NAT command. Just access-lists were configured. Now how do i acheive the same in the Cisco ASA 5515X with 8.6? I do not find any 'no nat-control' command available for it.
View 3 Replies View RelatedCisco Firewall :: ASA 5515X Max Contexts In HA Mode
Jun 4, 2013What is the maximum number of contexts a pair of 5515Xs in HA mode can support?
I know each 5515X can have a max of 5 contexts, but does that mean in HA mode a pair can support 10 with license pooling?
Cisco Firewall :: ASA 5515X - How To Block Traffic Of P2P
Jan 28, 2013I'm using ASA 5515X my concern is I was not able to block the traffic of P2P such as BitTorrent etc. I was also view some technotes on how to use webfilter without using Websense or Smartfilter tools and lucky I'm able to block certain websites. how to block the traffic of P2P?
View 2 Replies View RelatedCisco Firewall :: Upgrade From ASA-5510 SSM20 To ASA-5515X?
Dec 25, 2012I need to upgrade to firewall which supports Active/Standby configuration.I am currently using a ASA-5510,SSM-20 8.2(5).Will the configuration file from the ASA-5510 work on the 5515X?
View 1 Replies View RelatedCisco Firewall :: Remote Desktop Connection To ASA 5515x
Feb 5, 2013I have ASA 5515x and it has already Internet Connection since my firewall is not "production". So right now I'm trying to configure a Remote Session just for a test and eventually I was not able to connect from it. I followed the instructions from technotes but still Remote Connection dropped. Here's my sample configuration on my firewall, btw I also configured a service policy rule and ACL just to make sure if I can able to access the Server inside my network but Session also dropped.
nat (inside,outside) source static 1.1.1.1 2.2.2.1
access-list 110 extended permit tcp host 3.3.3.1 host 2.2.2.1 eq 3389
CiscoASA(config)#class-map rdpmss
[Code].....
Cisco Firewall :: Management Interface In Cluster ASA 5515x?
Jan 6, 2013I have a misanderstand about management interface configuration in cluster. So I have a cluster asa 5515X with management interface. i Would like to be able to connect to any of the member of my cluster on management interface, so i would like to fix a different ip on management interface on each of my node ip 92 and 91. I think it is the only way to make asa firmware update to access local flash on each node.
my config
interface GigabitEthernet0/1
channel-group 1 mode active
no nameif
[Code].....
Cisco Firewall :: Ports To Be Opened Up For Hosted Voice Access On ASA 5515X
Sep 23, 2012I have a customer who is going to host a VOICE services like providing SIP services to its customers. What specific ports required to be opened up for this on ASA 5515X. I would rate it ASAP.
View 3 Replies View RelatedCisco Firewall :: New ASA 5515X Generation Support PBR Or Not / ISPs Links Redundancy
Jun 9, 2013I need to know if the cisco ASA next generation specially ASA 5515X support PBR or no ?how to implement it? Also if i have many internet connections and i need to dedicate 2 ISP’s ADSL internet lines to certain service (such as mail) if the 1st fail, so the 2nd line come up to make redundancy with it ----------- Is this available on cisco ASA next generation.
View 1 Replies View RelatedCisco Firewall :: Maximum Number Of 1-1 Static Nat Entries On ASA 5515X Or 5525X?
Aug 7, 2012I have a FWSM cluster that I exceeded the maximum number of static nat entries on. i migrated the connectivity off to a pair of PIX 535's that seem to be handling the adderess translation needs. however the number of NAT entries being required is increasing and being the PIX series wal EOL'd several years back..I need to replace them.. The static 1-1 nat entries cannot be summarized into network as the hosts that are being nat'd are scattered all over various micro subnets in the all 3 rfc1918 ipv4 address ranges and they are being manged directly by snmp and SNMP-trap and other services that prohibit the use of many-to-one nat. Is there a mknown maximum number of static 1-1 nat entries that can be defined on the ASA 5515-x, 5525=x and higher ASA firewalls? Say I wanted to be able to grow to 2500 or more static 1-1 nat entries. I am currently running 2010 1-1 static host nats currently.
View 1 Replies View RelatedCisco Firewall :: Route To Internet Through Old PIX515 Firewall
Jun 10, 2012We have a wifi network for guests, that we route to internet through an old PIX515 Firewall. We recently tuned the timers to lower values in order to "save" on resources and publix address usage.
The timers we use are:
-timeout xlate 0:30:00
-timeout conn 0:30:00 half-closed 0:05:00 udp 0:02:00 icmp 0:00:02
Through verifying the new timers, we noticed at some xlate connections (TCP PAT) that are idle for ever!!In the connection table, I cannot find an idle connection for longer than 1h....
Cisco Firewall :: ASA 5540 Want To Ping Across Inside To Outside For Testing
Sep 27, 2012ASA 5540 8.2 (5)I have tried many combinations of command line syntax suggested in this forum but none are providing success so far.
I want to ping from the Inside Interface across to the Outside Interface and visa versa.I have tried various ACLs as well as "inspect icmp" in the config, etc still no go.
I can ping each interface from the console command line but cannot ping across each interface. [code]
Cisco Firewall :: ASA 5520 8.4 Failover Interface Testing?
Jan 3, 2012From ASA 5520 we tested the interface failover it not working even the interface are getting monitor .
primary is active.
Manually we shut the outside interface of the primary device configuration is getting reflecting in secondary as outside interface shut. Interface failover not happen.
ii All the interface are getting monitor when we gave command sh failover. even though when we shut outside interface failove not happening.
how to do the interface failover in ASA 8.4 version.
Cisco Firewall :: 5510 Trace-route / Antispoofing On Not Default Route
Jun 24, 2011I've enabled antispoof on all interfaces on asa 5510.If you start a traceroute to a network on the default route, everything works, since replies comes to an interface with route 0.0.0.0/0 defined.If you start a tracer route to a network that is NOT on the default route (let's assume coporate MPLS), you only get response from first carrier router, the other are discarded because of anti spoof violation.
I have ICMP inspection and icmp-error inspection enabled.
Cisco VPN :: ASA5505 Firewall - Route Internet Via External?
Feb 6, 2013I would hereby like to inform if it is possible to configure the Cisco ASA5505 firewall to route internet via an external VPN, while a laptop and smartphone connect to the firewall via Cisco AnyConnect VPN.
The configuration would result into: Laptop on public internet -> Cisco ASA5505 VPN -> External VPN (Unix server) -> internet.
Cisco Routers :: Configure SR520 To Route Internet VLAN To Firewall
Jan 20, 2012My operations manager says "Could you go on-site and configure a new clients new internet connection?" I make the arrangements and go on-site. As I'm working with the providers tech he says "Do you have a sub-interface confgured for a dot1q VLAN id of 1057?", I say "What?". Anyway my firewall is not capable of dot1q VLAN, so he says "Do you have a Cisco router that can provide the trunking?", I say "Yes, I tink so but not with me". The question is can I use an SR520 between my firewall and the provider demarc to route the VLAN he is talking about? My initial discovery says yes but I am not quite sure of the details on how to achieve this on the SR520.
View 2 Replies View RelatedHome Network :: How To Route All Traffic Only Via VPN
Aug 21, 2011I am using OPEN VPN in order to connect to a Canadian VPN server.I want ALL internet traffic to ONLY use the VPN connection and no traffic shall pass through my local ISP under any circumstance.In the event the VPN disconnects, I DO NOT want any internet traffic automatically sent via my LOCAL ISP connection. Can I simply disable my LAN network adapter in windows AFTER the vpn is connected? (since vpn uses its own TAP adapter?)
View 2 Replies View RelatedHome Network :: Cisco 877W - Create Route Or New Link(s)?
Mar 22, 2011I have the above router on 10.10.10.1 which I'm quite familiar with but I need reaching a VM residing on one of my internal MAC's. My cisco route table is as follows:
Gateway of last resort is 93.97.20.1 to network 0.0.0.0
93.0.0.0/21 is subnetted, 1 subnets
C 93.97.16.0 is directly connected, ATM0.1
10.0.0.0/24 is subnetted, 1 subnets
C 10.10.10.0 is directly connected, BVI1
S* 0.0.0.0/0 [1/0] via 93.97.20.1
The internal physical machine that contains the VM is 10.10.10.9 whose routing table is:
Routing tables
Internet:
Destination Gateway Flags Refs Use Netif Expire
default 10.10.10.1 UGSc 6 8 en0
10.10.10/24 link#4 UCS 5 0 en0
10.10.10.1 0:1b:2b:cc:7:8a UHLWI 7 1248 en0 284
10.10.10.9 127.0.0.1 UHS 0 86171 lo0
10.10.10.11 0:23:54:2a:6:d3 UHLWI 0 234 en0 150
10.10.10.30 0:9:34:28:60:2e UHLWI 0 25 en0 857
10.10.10.111 0:1d:ec:2:2d:2d UHLWI 1 1599 en0 721
10.10.10.255 link#4 UHLWbI 2 18609 en0
10.37.129/24 link#8 UC 2 0 vnic1
10.37.129.2 0:1c:42:0:0:9 UHLWI 1 2 lo0
10.37.129.255 link#8 UHLWbI 2 14046 vnic1
10.211.55/24 link#7 UC 2 0 vnic0
10.211.55.2 0:1c:42:0:0:8 UHLWI 0 2 lo0
10.211.55.255 link#7 UHLWbI 2 14046 vnic0
127 127.0.0.1 UCS 0 0 lo0
127.0.0.1 127.0.0.1 UH 5 214223 lo0
169.254 link#4 UCS 0 0 en0
The VM has a static IP of 10.211.55.5 and can obviously ping out to the rest of my lan but as of yet my router and other machines on the 10.10.10/24 subnet cannot reach the VM. I sort of presume this is a simple task of adding some kind of static route on my router and then all other machine will know how to get to the VM. So what do I need to do as I have about 40 or so customers already connected of whom I do not wish to suddenly halt their access due to my inexperienced attempts to create this route or new link(s)
Home Network :: Create A Manual Route Into Laptop
Jun 6, 2012My laptop have 2 NIC attach it, the cable NIC and Wireless NIC, the cable one connect to my lab network environment and the Wireless connect to office network environment (connect to internet) which both have differen segments [code] when my Wireless was turn off my pc can ping to all segment on my lab network environment, but if the wireless was turn on, i cant ping to others segment but only my laptop segment and i still could surfing to the internet without any problem.then i tried to add a new route from my laptop using "route add x.x.x.x mask x.x.x.x (gateway)" in command line and after that i can ping back to all segment in my lab network environment eventhough my wireless was onwhy i have to create a manual route into my laptop so that i can have connection between my laptop and my lab environment in the condition my wireless turn on ??
View 8 Replies View RelatedHome Network :: How To Connect And Prioritize Different Networks To Wifi Route
Oct 11, 2012I work in a small village in Africa and Interent access is often very unreliableTherefore I have 3 different ways of accessing the Interent from my home.The cheapest is Wifi from a local provider, but that doesn't always work. More expensive and still often unreliable is a 3G access. Then, when WiFi and 3G don't work I still can access the Internet via a Inmarsat BGAN satellite terminal, but that is very expensive.What I'd like do is to connect several computers to the same WiFi, 3G, BGAN Satellite Interent (all Ethernet) access via a home WiFi network.Now the questions I have:- can I just connect everything to a switch and then to the Wan-port of a wireless router?- how do the prioritisation works? When there is 3G available, I dont want to access the Internet via the BGAN, bacause that's too expensive?
View 2 Replies View RelatedHome Network :: Multi - WAN Router / Client Choosing Default Route
Jun 21, 2012is it possible for a client to choose a WAN to use when being routed through a Multi-WAN router? Something that could be configured as default route in linux or default gateway in winxp ?Or is this decision totally up to the router itself ? [code] Could now a client on the subnet 192.168.0.0/24 choose 1.1.1.1 as a default route for example? And if not, could this be possible if the router hat some secondary internal IPs for both WAN interfaces.
View 3 Replies View RelatedHome Network :: Use Internet Of Workplace From Home Via Dial-up Connection?
Oct 3, 2011I have ADSL modem in my workplace that is connected to a switch and other workplace computers are connected to this switch so the ADSL internet is shared in LAN network.(in each of computer I set default Gateway to ip of modem .....)I want to dial my workplace from home and then use of workplace internet or connect to workplace LAN.(such as VPN or Port Forwarding or I don't know...)
View 11 Replies View RelatedCisco Firewall :: Removing Route-map From Pix 525
Nov 1, 2012I have pix firewall 525, configured with ospf process. We are also performing route filetering in ospf process using route-map. Now we want to remove this route-map from ospf process. Any step-by-step process for removing route map as per below list. How to remove route-map without having any impact as per above configuration.
View 1 Replies View RelatedCisco Firewall :: Route Tagging On ASA 8.4?
Mar 16, 2012how to tag static routes on ASA. I have static routes that I want to redistribute into EIGRP on ASA. I can't find any tag option when defining a static route or under set command in route map... am I overlooking something?
View 1 Replies View RelatedCisco Firewall :: Trying To Get ASA5505 To Route
Nov 14, 2012customer's WAN solution, instead of buying routers, purchasing department bought ASA's (don't even get me started!). So I have 5 ASA 5505's for the branch offices and one 5510 for the Head Office. I am trying to get them to behave like routers and pass the traffic across. I set up a lab with a 5505 and the 5510 using an ethernet cable for both Outside interfaces since the WAN links are going to be MetroEthernet Layer 2 anyway.
I tried static routes, dynamic routing, I followed examples from other persons who did it and it doesn't work. I attached the configs here to show I have the default routes, specific static routes pointing the traffic out, any any rules configured as well. I cannot ping from the internal lan of the 5505 to the internal lan of the 5510.
Cisco Firewall :: ASA5510 / Default Route With Different AD Value?
Nov 14, 2011Will ASA5510 support default route failover mechanism by giving two different AD value in the route outside command?
View 1 Replies View RelatedCisco Firewall :: Route To Same Interface On ASA 5510?
Sep 14, 2011I would like to route traffic that are coming in and going out to the same interface on ASA. I am using inside interface with security-level 100. In this URL, [URL], ASA is able to do that.
View 5 Replies View RelatedCisco Firewall :: NAT Route For Remote VPN On ASA 5510
Nov 15, 2011I have configured a remote access VPN on my Firewall ASA5510. Everything worked fine and I can successfully connect through the VPN. The problem is I cannot ping or connect to any of my internal network resources. I tried to add a new NAT route from outside to my internal servers using the defined pool but due to a new ASA version there are many changed I see in the NAT routes
View 37 Replies View Related