Configure Dsl Port Forwarding
Sep 25, 2012To configure DSL port forwarding,I want to configure as remote desktop.
View 3 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Configure Port Forwarding On 887
Aug 11, 2012I need to configure the port forwarding on Cisco 887 to forward port 22 on Public IP to a LAN IP port 2200. I don't know anything on Cisco router at all, beside telnet to the cisco and quit . Any step by step command.
View 9 Replies View RelatedCisco Firewall :: ASA 5505 Can't Configure Port Forwarding
May 20, 2012I have ASA 5505 with 8.4(2)8 software for one of my branch offices and I can't configure port forwarding.It seems to be very simple, but it's not working. I use my ASA as a gateway to the internet for users in office and for site-to-site IPSec VPN to HQ. I have pppoe-enabled outside interface, but ISP gives me static routable ip address. I have server behind my firewall and I should "publish" to the WAN some of its' tcp and udp ports, but I see that no packets forwarded through ASA. I tried to configure PAT as stated in official "Cisco Security Appliance Configuration Guide" through CLI and ASDM.[code]
View 4 Replies View RelatedCisco Switches :: To Configure Port Forwarding On SG300-20
Sep 17, 2011I have a Cisco SG300-20. I have read the documentation and cannot seem to locate the instructions for port forwarding. I need to forward TCP port 8088 to IP address 192.168.14.110 on the switch.
View 5 Replies View RelatedLinksys Wireless Router :: Configure Port Forwarding On Cisco 887?
Aug 12, 2012I need to configure the port forwarding on Cisco 887 to forward port 22 on Public IP to a LAN IP port 2200. I don't know anything on Cisco router at all, beside telnet to the cisco and quit.
View 1 Replies View RelatedCisco Firewall :: ASA5505 - How To Configure Port Forwarding For All Devices
Apr 18, 2012How to configure this setup.I have an ASA5505 with dual wan failover, FiOS (eth0) & Cable (eth1). how to configure the port forwarding for all my devices so it doesn't matter what external interface the traffic is coming from. For example, I need web traffic on port 80 forwarded to 192.168.1.150 regardless of whether it is coming through eth0 or eth1.
View 2 Replies View RelatedCisco WAN :: 877 Configure Port Forwarding To Remote Server Over Tunnel?
Jun 28, 2012Can this scenario be done one the cisco 877 router? I have VPN Ipsec up and runing on both site. How can to configure the port forwarding to the remote server over the tunnel? url...
View 16 Replies View RelatedCisco Routers :: RV042 V3 And SBS 2003 RWW - Why To Configure For Port Forwarding
Sep 14, 2011I have tried replacing a loaner RV082 V2 with an RV042 V3 router with firmware 4.0.4.02. All worked well, including the site to site VPN. However, in spite of the fact that I have ports 443 and 4125 forwarded to the server (192.168.2.10), we are unable to connect via RWW. There is no such problem with the RV082. What is different with the way we configure these V3 routers for port forwarding?
View 2 Replies View RelatedCisco Firewall :: ASA5505 Configure Port Forwarding To Multiple Internal IP Addresses
Jun 21, 2012ASA 5505 Firmware 8.3(4), ADSM 6.4(2).I have a public IP address of 168.87.3.4.I need to forward ports (5060, 5080, etc.) to one internal address. (192168.1.1).I need to foward different ports (10020-10080) to a different internal address (192.168.1.2) Everything I read tells me how to do this in a 1 to 1 static NAT.
View 1 Replies View RelatedCisco Switching/Routing :: 881W - IOS Port Forwarding Commands For Port Forwarding
Apr 7, 2013I am trying to open up port 32400 on my 881w Cisco router but I have not had any success I need to configure manual port-forward to enable my Plex Media server.
View 1 Replies View RelatedCisco Routers :: RV042G - Port Forwarding To 2 Different Destinations Based On Incoming Wan Port
Apr 22, 2013how to: port forwarding to 2 different destinations based on incoming WAN port
The default HTTP service works fine: TCP80/80-> 192.168.0.55
I have a couple of IP security camera's I'd like to be able to access remotely that also listen on port 80. I tried TCP & UDP 8009/8009-> 192.168.0.9 without any luck. Not sure how to handle the port redirects on the RV042G? Seems simple and was on the Symantec, could be user training :-)
I was able to do port redirect with the Symantec Firewall I'm replacing.
TP-Link ADSL2+ Wireless :: TD-8970 Port Forwarding To A Different Internal Port
Mar 7, 2013Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n
ISP : Virgin Media
Is there any way of forwarding an external port to a different internal port on the TD-8970 ?I saw a question posed on an Australian forum implying that it might be provided in a later firmware release.Our TD- 8970 has replaced a previous NetGear WAG 320N which had this facility, and is useful to provide access to multiple machines without having to modify each individually to use a different port.
Cisco Firewall :: Change Default SSH Port On ASA 5505 (port Forwarding)
Dec 2, 2011So here is my network.
ASA5505--->Cisco1841--->Cat2960
Code
ASA asa831-k8.bin
Cisco 1841 c1841-adventerprisek9-mz.151-4.M2.bin
Cat 2960 c2960-lanbasek9-mz.122-55.SE1.bin
and here is my dilemma.
I can SSH from the internet to my ASA on default port 22, directly to my public IP. I can SSH from the internet to my Cisco 1841 on port 2001. I can not however, SSH to my Cat 2960. From what i can tell, on the Cat2960 i can't change the default port 22 for SSH to different port, just like i did on the Cisco 1841. I looked to see if I can change the default port for SSH on he ASA, it does not look like this is an option.
The bottom line is that i want to be able to SSH to all three devices from the internet. I only have one public IP. As of now, what i can do is only SSH to the ASA on default port 22 directly to the public IP and Cisco 1841 on port 2001. It appears that changing the default SSH port on Cat 2960 is not an option. It also appears that I can't change the default SSH port on the ASA, if i could, i would and then i should be able to SSH to the Cat 2960 on port 22. No matter what i did on the ASA, it always listens on port 22 for SSH connections.
show asp table socket
TCP 001f549f <<pub IP>>:22 0.0.0.0:* LISTEN
how do i make it listen on different port?
Here is relevent config for SSH for cisco 1841 (port forwarding)
ON ASA
object network ROUTER
host 10.10.1.1
[Code].....
Cisco Routers :: RV042G Port Forwarding From Public Port To Internal IP?
Oct 11, 2012Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23 ?
First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80
D-Link DIR-655 :: Subsonic Port Forwarding / Get Machine - Port From Outside / Internet
Feb 16, 2011I am having an issue opening a port (4040) on the 655 for my Fedora-based subsonic server. Inside the LAN, I can see the device from other peer machines, so I am confident the port is open and listening. However, I can't seem to get to the machine-port from outside/internet.
I have tried Virtual Server and Port Forwarding with single port. The server has a stactic IP which I've included in the DHCP range and outside the range. I have a DSL connection (AT&T), modem only. I have updated firmware. I have exhausted the Subsonic community's knowledge, everything points to the router, but all the settings seem correct. What am I missing? Is if possible there is a defect in the router? (don't laugh). Is there a way to trace a request to that port to see where it is hanging?
(yes, I've STFA, but don't know what else to do).
Cisco :: Not Enough Port Fields In Port Forwarding For Linksys E4200
Jul 16, 2011I have always used netgear routers in the past. After a series of issues regarding configurations not working correctly I invested in what appeared to be a semi pro router, the cisco linksys e4200.
I have a centralized server which I use to access a mass of different services such as mail, dns, VPN, FTP, Kerberos, http and many more. While I am not a massive networking ****, this server setup is like my garage project. To access these services externally to my LAN as far as I understand I would need to configure port forwarding for each service to my server. Unfortunately the control panel for the linksys E4200 only offers about 15 custom port fields for forwarding, and some documentation I have read shows that with it's basic install my server could be using up to 60 ports at once.
Is this router just not suitable for this sort of network. If so I will be very disappointed because I have spent a quarter of the price on netgear routers with more control than this.
Cisco Routers :: SRP541W Set Up Port Forwarding From External Port
Apr 13, 2013I've set up port forwarding from an external port (9000) to an internal port (80) on our SRP541W, and for some reason, it's not working externally. If I access the public address from within the internal network, it works properly.
View 6 Replies View RelatedHome Network :: Port Forwarding Not Access Port
Jul 31, 2011I want to create a Counter Strike Server and need to open some ports for that.The Problem: I cannot seem to open the ports for gaming.The Modem Setup: My Firewall is disabled.My guess is that, this is the area with the problem. I guess my modem is not forwarding onwards.The Problem: I tried checking my ports with websites like URL etc.It cannot access my port.
View 1 Replies View RelatedPort Forwarding Port 80 Blocks Internet For Everyone Else?
Aug 7, 2011I have a DSL-524B from D-Link. My problem is, whenever I Port Forward port 80 to my comp's IP to host a web server, all the other computers connected to the router are unable to access the Internet. So, I set up no-ip to use port 8080, but, this exposes my ip and even when masking, if you look at the HTML code, you get the ip.I need to know how to open up port 80 without restricting Internet access to only my comp, or any other work around.
View 7 Replies View RelatedCisco WAN :: 857 ADSL Possibility To Configure Fast Ethernet Port As WAN Port
Apr 4, 2012I have a Cisco 857 router which i used for Internet connection with RJ11 connectior (ADSL0 POTS) but now the ISP has changed the internet link with PPOE type and the ONT connection is RJ45 , Is there a possibility to configure one os the Fast Ethernet ports as WAN port for internet.
View 2 Replies View RelatedDI-524 / Port Forwarding With ATT DSL?
Nov 10, 2012I was at a friend's office today trying to get the IP cameras working but forwarding the ports seems not to work with his current modem from ATT (a Westwell F90 or something). Would the workaround for this be purchasing a third party modem instead that supports port forwarding and stop leasing the Westwell F90 from ATT?
edit: the modem is hooked up to a DI-524 from D-Link and i already forwarded different ports to see if it was specifically port 80, 1024 etc
Cisco :: How To Configure A Trunk Port As Network Port
Feb 27, 2012What is network port ? I want to configure a trunk port as network port, so that the trunk port becomes the network port for all the VLAN associated to the port.
View 18 Replies View RelatedWay To Get Port Forwarding In Server
Oct 21, 2011[code]...
How do i setup port forwarding in server 2008?? I have heard numerous ways of doing this through windows firewall, NAT and setting up static routes. Not of which i can get working.
Port Forwarding In A Cisco PIX 501
Apr 1, 2012I finally got my Cisco Pix 501 working on my network and everything is working great! However, I do host game servers on occasion and I have a 24/7 FTP server up and as of now, I can't connect to it because the PIX is blocking the ports!I have zero experience with Cisco, so I need step-by-step instructions on what commands to enter to get this thing working!
View 5 Replies View RelatedCisco :: ASA 8.4 And Port Forwarding
Mar 12, 2011I am very confused now. I got my 5505 for home (basic) and loaded up 8.4(1) fresh. From the inside interface I can reach the internet no problem but I am having issues trying to get my port forwarding to work with torrent. inside host is 10.100.130.5 port is 26883, I have been trying to configure this forever.
View 9 Replies View RelatedPort Forwarding Not Working
Jul 7, 2012I am trying to make a server in the game Halo combat evolved for the PC, but i need to forward 3 ports, ports: 80, 2302, and 2303, i did them all, but it still says they are all still closed, when I scan them or they say, its times out.I have a D-Link router.
View 5 Replies View RelatedStatic IP For Port Forwarding?
May 25, 2012I need to set a static IP for port forwarding so my clients can connect directly to my server. I kept losing people because my IP address would change every week. I use version MI424WR router and know my Mac address but do not know which IP address I should set it to.
View 6 Replies View RelatedDLink DIR-601 - ICS And Port Forwarding
Nov 18, 2011I have a computer connected through wifi to the internet.I then turn on the computer into ICS mode and connect that to my PS3/Xbox.I'm trying to get an OPEN NAT type but just can't seem to get it working.I've read a few different pages and have tried some things but it's never worked.I've heard of bridging connections and the sort but I'm not familiar with it. I just want to get an OPEN NAT on my PS3/Xbox.
View 10 Replies View RelatedPort Forwarding On A Cisco PIX 501?
Apr 1, 2012I finally got my Cisco Pix 501 working on my network and everything is working great! However, I do host game servers on occasion and I have a 24/7 FTP server up and as of now, I can't connect to it because the PIX is blocking the ports!
View 12 Replies View RelatedPort Forwarding On BT Home Hub 2.0?
Feb 14, 2011I have Infinity so don't know if that's an issue in my situation. I know I'm being "throttled" by BT when doing P2P downloads so limit this to off peak periods.I have made the recommended tweaks to Utorrent to speed things up and finished off today by port forwarding. I tried to follow the tut I was using to the letter but the download became even slower!! You have to enter the port number in the Hub settings but I wasn't sure whether it was a single number xyz or a range 0-xyz or even xyz-xyz. I really hope I'm making sense.I also wasn't sure whether it's TCP or one of the other options I should have selected. I'm currently on Infinity getting 37.4 Mbps download and 1.7 Mbps upload.
View 8 Replies View RelatedCisco VPN :: VPN Port Forwarding On 877?
Apr 6, 2011We have the above router for a small business and I want to configure VPN to port forward to the server so it can handle the VPN traffic through Routing and Remote Access.I have configured port forwarding on SMTP, RWW and other protocols successfully but VPN will not work.Within the built in web interface on the Cisco it advised that if I want to configure VPN I need to use Cisco Config Pro. I have had a look through this software but it looked to only support the router as the VPN gateway rather than port forwarding to a server.
View 9 Replies View RelatedCisco LAN :: 871 - NAT Port Forwarding
Jul 10, 2007I have recently purchased a Cisco 871 router. In the GUI from the installed software, I have been able to configure which ports are forwarded to a specified IP address within my local area network. This seems to output a configuration line like this:
ip nat inside source static tcp 192.168.1.123 1000 interface Dialer0 1000
However, I can only do this one port at a time. Is there a function or command that I can use to specify a range of ports? For example, I would like to forward tcp ports 1000-2300 to the IP address 192.168.1.123
Cisco :: Port Forwarding On 5505?
Sep 2, 2012I have the following configuration in my ASA 5505 and I'm having problems connecting with other players on my XBox.
I think my problem is that I need to forward ports tcp:3074, udp:3074, and udp:88 to my xbox which is at 192.168.2.50 (vlan 3 below).