Cisco Routers :: SRP547w - Change Default IP And Create Additional Users
May 12, 2013
Ive changed the IP address of a laptop to connect to the router with IP 192.168.15.1 but now want to change the router IP address from the defaul to another subnet, so that it is accessable with other workstations on the LAN, but I could not readily find the option to set the Ip address on the router.
I'm signed in with user admin.
I also wanted to add addiontal users. The help indicates there is a User List Add Entry option but from the Administration bar, the left hand menu option shows User Management & User Privileges options. On User Management, it is possible to change the 2 default user names, but I wanted to leve them and create new ones.
I have a SRP547W that I have configured the following way:
LAN 192.168.15.1/24 VLAN1 LAN 10.10.10.1/24 VLAN10 LAN 10.10.2.1/24 VLAN100 PPPOE ADSL Software DMZ going to 10.10.10.x and another to 10.10.2.x - this is working OK
I now want to use the Advanced Firewall features to block all ports except those that I need as the software DMZ forwards everything. When I try to create the rules I get "the values are invalid" message no matter what I try.
I want to create explicit allow rules, followed by a deny all rule for each of the IP addresses used for the software DMZ
Have I got the Subnet Mask Correct for the Destination IP? Or should it be 255.255.255.0? It doesnt make a difference either way
Policy DetailsNameValueSource IP Address0.0.0.0Source Subnet Mask0.0.0.0Destination IP Address10.10.10.xDestination Subnet Mask255.255.255.254ProtocolAnySource PortAnyDestination Port443ActionPermitScheduleEverydayTimes24 Hours
I am currently setting up a 2800 Series router, and prefer a username/password type authentication rather than a single enable password. To do this, I did:
This basically does what I want - when I connect to the router through console, it immediately asks me for a username and password. The thing is - as soon as I provide the right credentials, it takes me to USER EXEC mode (the default command mode). Is it possible to change that so that after entering the credentials, I go right into privileged exec mode?
Bonus question: As it is now, I just have no enable password, so when I login with my credentials, I issue "enable" to enter privileged exec mode without it prompting for an additional password. Is it safe to do it this way - having no enable password but requiring a username and password for login?
i see that the wifi on the SRP Freezes. If i am connected via lan, i can still surf the net or connect to another access point on the network and surf. But the wiress devides connected to the SRP loose connectivity even though it shows that the wifi connection is connected. I am running on the latest firmware. this problem has started occcuring only recently
There are a few discussions on this topic but nothing I can find indicated definativley shows that this can be done with this model.I have an ADSL service that came with 1 IP address and then we later purchased an additional 4 IPs (2 usable) for the same service.On our network we have SBS2011 and also a dedicated web server. What I would like to do is forward HTTPS to the web server on our inital IP and then forward https for OWA to one of the IPs on the additional set.Our initial IP is xxx.yyy.104.112 which I would like to forward port 443 to 192.168.0.12 - web server
The additional IPs are :
aaa.bbb.30.24 (Gateway Address) aaa.bbb.30.25 aaa.bbb.30.26 - I would like to forward this to 192.168.0.2 - SBS box aaa.bbb.30.27
I have tried as suggested in other thread setting up a software DMZ that sends public IP aaa.bbb.30.26 to 192.168.0.12. The xxx.yyy.104.112 to 192.168.0.12 works with a port 443 forward fine.
When I do this I cant connect from outside. If I change the port forward on 443 to go to 192.168.0.2 I can get to the SBS box from outside using the aaa.bbb.30.26 address .I have also tried creating a subinterface for the aaa.bbb.30.24 addresses and this also doesnot seem to work. Just I am basically asking for confirmation that this can be done with this model, I have put in the latest firmware.
I've got a network of SRP547Ws connected with site to site IPSec VPNs. But I can't get to the administrator loging page of the remote SRP547s over the VPN. Is there a setting or method I need to use ?
I have looked at the remote administration settings but this appears to be for adminsitration over the WAN interface rather the the IPSec VPN
Currently, I have setup a demo lab with the UC320W + IP Phones and OnPlus Network Agent all connected to a SG300-28P. I have just obtained an SRP547W because I wanted to use the 3G/4G internet connection via the router as my demo lab is an isolated network.Now, I tried to a couple of 3G modem (UMG181) and 4G Telstra modem (MF821) on the SRP547W but none of these work. I had a look at the compatibility tableI guess those modem models are not listed there. However, when I went on say the Optus website to scout for a more compatible model, none of them hit it right on the mark. The matrix says it can support E180 (while Optus has the E188), E353 (while Optus has the E353). I have already wasted my money on getting the earlier stated 3G/4G Modems and I ain't going to take a chance again.
I have an SRP547W hooked up as the office router with the standard office phones connected via the telephone ports at the back of the unit using 2 SIP lines as well as the PSTN by dialling hash first. We have just added a new staff member and bought an SPA303 with the intention of connecting it through registered SIP lines on the SRP547W, and hopefully have the facility to use the PSTN line when the SIP lines are busy.
The problem is, it connects to VLAN100 and gets its IP address and initializes fine however no lines show as configured and it can't make or receive calls. What do I need to configure on the SPA303 to tell it to use the SRP547W as its SIP Server/Proxy (not sure of the terminology).
I've purchased a router SRP547W and I would disable DHCP server. On the control panel I can't see anything about disabling this function. I don't need dhcp server on router and I don't need dhcp relay. My firmware version is 1.2.4_003.
We've run into some difficulty trying to take advantage of multiple WAN IPs in conjunction with the SRP547
What we're trying to acheive is the ability to port forward from our distinct public IPs to different internal servers. Looking at the options under Port Forwarding it looks like we can only configure forwards at the "WAN interface" level, but our problem is that we can't work out how to set up separate interfaces for each of our Public IPs...
Our ISP provides us with a fully managed NTU/router with a single "Internet" ethernet port, which we can use by statically configuring IPs on our end. For this configuration this port has been directly patched to the WAN ethernet port on the SRP547W.
We have been allocated a 255.255.255.248 (/29) subnet, giving us 5 usable IPs after the ISP's gateway address is taken into account, like so: a.b.c.208 Network Address (/29 subnet) a.b.c.209 ISP Gateway a.b.c.210 IP1
[Code].....
I should mention at this point that we're running on firmware version 1.02.01 (023).
Is there a CLI or other method of configuration that might work if the web interface won't?
We installed one of these devices as our gateway a couple of weeks ago, flashed the firmware to 1.2.4(003) and it worked perfectly until this morning where it keeps resetting the ADSL every minute and losing the web interface to the unit.
The log endlessly reports this: Feb 24 11:26:00 SRP547W cron.info cron[8779]: (root) CMD (/sbin/check_gn) Feb 24 11:26:00 SRP547W cron.info cron[8781]: (root) CMD (/sbin/check_ps)
I have a SRP547W which I'm trying to replicate a configuration I had on an old Cisco 847 that recently died.
My ISP has allocated me a /29. The DSL configuration means that the IP address on the PPP session is assigned randomly. I have a mix of internal devices on a private IP range and a few devices with publically accessible addresses. All of the devices on the internal network need to be NATted to a public IP from the range allocated to me.
I can see that I can use the software or hardware DMZ to set up the servers, but I can't see any way to configure the external NAT address.
I'm at the point of setting up admin access for engineers needing to have insight into the operations and status of our ACS 5.3 systems. any way to create a Dashboard that can be applied to all admin user accounts? (perhaps a custom role?)I've been able to customize the dashboard for my own account to show what is most relevant, but am unable to figure out how to apply this layout and setup to all other users.
Basically, I have a number of folks that need to see this data, but that I can't exactly count on to setup their own dashboards to show the important details. If there were some way to build a tab/dashboard/portlet, etc (whatver it may be) and have it apply to all users, that would save me TONS of work so that I don't have to login to each person's account and set things up for them.For example, I want to have all users see a tab/dashboard that shows the applet "Live Authentications", but with the protocol already configured to display TACACS vs the default which is RADIUS.
I have an ADSL connection and have configured the PPPoE subinterface on WAN1 (ADSL) this connection has a static IP, and I know that the ISP gives that to me through DHCP however I have 4 or 5 additional IP addresses also provided to me on that same link, and they are not given to me via DHCP.
How do I configure this router to have multiple fixed IP addresses on a PPPoE interface?
I also need to port forward some ports for each of the IP's but I assume this will be easy after i have the IP addresses setup.
As per the title, I just require 3 to 4 VLANS with inter-VLAN communication enabled.
In the past I have used this router with each port of the internal switch set to a different VLAN, with each in turn hooked up to an unmanaged switch. This has work fine for me but I want to dip my toe in the world of .1q VLANS and gain some added flexibility and neatness.
I have recently purchases a Cisco srp547w for my organisation. It is working fine with one SSID enabled. I have configured everything with no problems using the Web interface. However, whenever I click the Edit button, in the Security column, in the Wireless Table under Basic Wireless Settings I get a pop up message which says :"Some values have been changed. The router must restart the wireless module to take effect.Please wait several seconds" I have tried this using 3 different browsers and get the same behaviour in each browser.
I am trying to create a VPN between an SRP547W and a Cisco IOS router, in this case a UC540.I am running firmware 1.2.4 (003) Jan 11 2012. Now I can do this with an SRP527W and many other routers successfully. Including other IOS routers 1801, 1941 etc.
The issue I have is on the SRP547W I cannot create more than one IPSec Policy through a single IKE policy. I require this to route multiple v lans to our remote site. When I try to add an additional IPSec Policy I am give the error "IKE policy has been used by other IPSec policy"
This is possible to do on the SRP527W with latest firmware. I have tried rolling back to earlier firmware but instead I am given an error about overlap. Latest release note for this firmware suggest this issue was already resolved.
The SRP547W supports creating both Wifi Voice and Data vlans.Can I configure a Wifi IP Phone to connect to the SRP547W Voice Wifi Vlan and have the SRP associate it with Line 1 (in lieu of a standard phone connected to the Line 1 FXO port - without additional hardware)?
I would like to create a website to allow users to legally watch videos in streaming but I am struggling in understanding what the related cost would be from a storage and transfer stand point.
We have Cisco Cat4503 series L3 Switch and Cisco L2 2560 Series Switches, some of the users want to have a dynamic VLAN membership, and connecting with the network as mobile users,
can it possible and create dynamic VLAN for specific group of users.
when I click 'Create...' under Access Policies > Default Network Access > Authorization, and then press the 'OK' button, it says 'Please configure at least 1 condition.' However I have no way to configure conditions as the 'Conditions' text is just bold text and not a link or any sort of configurable area. If I go to 'Customize' on the bottom right and add conditions to the right list box, I still have no options when I press Create. Also, the 'green light' next to Default Network Access is grey with a line through it. This is the most cryptic system I have ever used
I have a RV042 with two ADSL services on it, that is a nice simple thing for this unit. The problem that I am having though is that one of the ADSL services also has a /29 attached to it.
How do you go about configuring this additional sub net? On a previous unit I have had to create IP aliases, and could then port forward and NAT without too many issues, but it doesn't appear that the RV unit seems to work the same way.
I have an rv220w router with one SSID and the product says I can add up to 4 additional wireless ssid ie the router is protected with wpa but we have guests that would like to connect to the internet while working in our building . I would like to add a guest SSID with wep security that I could give Clients. The problem I run into is every time I add the Guest ssid the wireless printers that are attached to the routers' main ssid quit working. I noticed that when the rounter was orginally set up the main SSID has IP addresses from 100 to 255 allocated. Do I need to limit the IP addresses in the Main SSID to a smaller number so that the Guest SSID can use the remaining addresses.
So far we add any router in the existing network simply by disabling DHCP server, and adding LAN ip for that. We don't add WAN detail at all in the additional routers. And plug one cable from main network to the LAN port of the additional routers.So we basically use that additional routers only as a access point for WIFI.But what I wonder is if it's possible for me to use the additional routers with the same feature as of the main routers i.e. Enabling DHCP server so that it too can give its own DHCP ip address.
For access by external users on our network use all Cisco VPN Client, we have a VPN3000 Concentrator and a Cisco ACS 2.6 for authentication.We wanted to upgrade to the latest release of ACS 4, x .... you can set a password expiration for VPN Client? Or make sure that the remote user can change password?
I'm trying to change the default name on my Sky router but when I try a pop up from Windows security is asking for my username and password which I don't have as I never set one up in the first place! is this the default password from Sky, Admin- Sky that I need to use?
I have noticed that under the Device Change Audit list under the configuration dashboard. LMS lists the wrong user for the last change. For example. User ABC performed a change on a switch yesterday but switch shows user XYZ has performed the change.
e.g.
SwitchA
! Last configuration change at 16:27:06 AEST Mon Aug 15 2011 by ABC
User XYZ then performs changes on switchB, switchC. These show up correctly. but the change on switchA shows user XYZ instead of ABC.
User XYZ has never logged into the switchA in question.
