Cisco Routers :: SRP547W Dropping ADSL Every Minute
Feb 22, 2012
We installed one of these devices as our gateway a couple of weeks ago, flashed the firmware to 1.2.4(003) and it worked perfectly until this morning where it keeps resetting the ADSL every minute and losing the web interface to the unit.
The log endlessly reports this:
Feb 24 11:26:00 SRP547W cron.info cron[8779]: (root) CMD (/sbin/check_gn)
Feb 24 11:26:00 SRP547W cron.info cron[8781]: (root) CMD (/sbin/check_ps)
[Code].....
View 17 Replies
ADVERTISEMENT
Mar 2, 2013
I have installed a couple of SRP547W's and can't ping the external side of the ADSL interface.
Is there an option to turn on "respond to ping" and also are you able to forward to a internal IP?
View 3 Replies
View Related
Oct 25, 2011
I'm installing a new SRP547W for a client and am having trouble setting up a site-to-site vpn. They are using the WAN1 ADSL interface for their internet connection. When I add a sub interface to it I am unable to see the 'Connection Type' drop down like I can see on a WAN2 ethernet sub interface. I have followed the instructions on page 29 provided here: how I can get a a site to site vpn set up on this router using either PPTP or L2TP over the ADSL interface.
View 1 Replies
View Related
Feb 7, 2011
I've got a ADSL Sweex Modem, connected to a D-Link Wireless Router,The modem is connected to our telephone line, we have other phones connected to other "telejack" too. The router is connected to a computer with wire, and another computer wireless.Every now and then we get random disconnect. Sometimes we can go several months without a single disconnect,whilst sometimes it happens as often as every 3 minute. This is the log:
[code]....
View 14 Replies
View Related
Nov 30, 2011
I'm using the 802.11 Mode Mixed, with WPA (Both WPA-WPA2).
I'm new but I recently bought a new D-Link DIR-615 router. After getting everything setup manually due to the cd install not working properly. I was walked through the manual setup with D-Link Tech Sup. Now everything is working fine, but when I go to open mushclient and log into one of my mushes to rp, I will connect just fine, but after a min or so the connection drops on the client itself.
Now before this D-Link, I had a Netgear router and Lynksys Routers, ran the install software and everything. Things worked, I was able to login to my mushes and not worry about getting disconnected from them. But now with his router, I feel because I didn't install the software, that something wasn't setup properly and I have to reconnect to the mush every few minutes. Now the internet doesn't drop, I'm still online, still able to surf, able to play on my Xbox 360 and connect online with my laptop. But this one program, the connection drops constantly. Now If I just connect using just my modem, I can stay connected until the mush times out due to me being idle for say about 8mins. But if I'm chatting with someone in Mushclient, the connection drops and I have to reconnect.
View 2 Replies
View Related
Mar 22, 2012
I just brought home an older desktop and my wireless connection seems to disconnect about every 30 seconds to a minute, then reconnects.
The only other devices that we are using wirelessly are our phones, which we never notice a problem with. When it is connected, the signal stength is excellent. It just keeps dropping. Speed 72.0 mbps.
I am using a Linksys E-1200 wireless N router, and a Belkin N150 USB adapter.
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows XP Professional, Service Pack 3, 32 bit
Processor: Intel(R) Pentium(R) 4 CPU 2.80GHz, x86 Family 15 Model 4 Stepping 1
[Code].....
View 14 Replies
View Related
Apr 12, 2012
I've recently purchased the EA3500 dual band wireless-N router to replace my old and somewhat tired WRT54GS. The old router worked, I just decided to upgrade to wireless-N since all of my devices are now capable.My ISP is Comcast and I use a Motorola SB 6120 cable modem. After an extremely easy setup of the new router last week, I experienced one full day of glorious speedier network and internet traffic. However, roughly 24 hours after installation I started experiencing intermittetent internet connectivity issues. As in - the cable modem is accessible for 2 minutes and then can't be found for 2 minutes, repeat forever.
After multiple different troubleshooting steps, including rebooting both the modem and the router together, separately, and releasing and renewing the router's IP Address through the router's admin page, I finally ended up resetting the router back to factory defaults and letting Windows 7 guide me through the re-installation rather than using the provided "easy setup" CD from Cisco.
This seemed to have worked, but 2 days later, my "every 2 minutes" issue returned.
Something important to note here is that all of my devices - both wired and wireless - are able to communicate with each other without issue. For example - while I have no access to the cable modem, I am able to stream music from a wired desktop through a wireless laptop to a wireless receiver connected to my TV. I am also able to access the router's admin tools during my connectivity issues.
View 1 Replies
View Related
Apr 2, 2012
i see that the wifi on the SRP Freezes. If i am connected via lan, i can still surf the net or connect to another access point on the network and surf. But the wiress devides connected to the SRP loose connectivity even though it shows that the wifi connection is connected. I am running on the latest firmware. this problem has started occcuring only recently
View 3 Replies
View Related
Mar 18, 2012
There are a few discussions on this topic but nothing I can find indicated definativley shows that this can be done with this model.I have an ADSL service that came with 1 IP address and then we later purchased an additional 4 IPs (2 usable) for the same service.On our network we have SBS2011 and also a dedicated web server. What I would like to do is forward HTTPS to the web server on our inital IP and then forward https for OWA to one of the IPs on the additional set.Our initial IP is xxx.yyy.104.112 which I would like to forward port 443 to 192.168.0.12 - web server
The additional IPs are :
aaa.bbb.30.24 (Gateway Address)
aaa.bbb.30.25
aaa.bbb.30.26 - I would like to forward this to 192.168.0.2 - SBS box
aaa.bbb.30.27
I have tried as suggested in other thread setting up a software DMZ that sends public IP aaa.bbb.30.26 to 192.168.0.12. The xxx.yyy.104.112 to 192.168.0.12 works with a port 443 forward fine.
When I do this I cant connect from outside. If I change the port forward on 443 to go to 192.168.0.2 I can get to the SBS box from outside using the aaa.bbb.30.26 address .I have also tried creating a subinterface for the aaa.bbb.30.24 addresses and this also doesnot seem to work. Just I am basically asking for confirmation that this can be done with this model, I have put in the latest firmware.
View 3 Replies
View Related
Sep 5, 2012
I've got a network of SRP547Ws connected with site to site IPSec VPNs. But I can't get to the administrator loging page of the remote SRP547s over the VPN. Is there a setting or method I need to use ?
I have looked at the remote administration settings but this appears to be for adminsitration over the WAN interface rather the the IPSec VPN
View 2 Replies
View Related
May 29, 2012
Currently, I have setup a demo lab with the UC320W + IP Phones and OnPlus Network Agent all connected to a SG300-28P. I have just obtained an SRP547W because I wanted to use the 3G/4G internet connection via the router as my demo lab is an isolated network.Now, I tried to a couple of 3G modem (UMG181) and 4G Telstra modem (MF821) on the SRP547W but none of these work. I had a look at the compatibility tableI guess those modem models are not listed there. However, when I went on say the Optus website to scout for a more compatible model, none of them hit it right on the mark. The matrix says it can support E180 (while Optus has the E188), E353 (while Optus has the E353). I have already wasted my money on getting the earlier stated 3G/4G Modems and I ain't going to take a chance again.
View 1 Replies
View Related
Aug 9, 2011
What is the current list of supported USB modems for the SRP547W router?
View 1 Replies
View Related
Nov 14, 2012
i purchases cisco rv 082. i set MTU vale at 1500.i use public IP for WAN and just using one WAN.
View 4 Replies
View Related
Jan 18, 2012
How to config SRP547W to support ANNEX M
View 4 Replies
View Related
Oct 28, 2012
I have an SRP547W hooked up as the office router with the standard office phones connected via the telephone ports at the back of the unit using 2 SIP lines as well as the PSTN by dialling hash first. We have just added a new staff member and bought an SPA303 with the intention of connecting it through registered SIP lines on the SRP547W, and hopefully have the facility to use the PSTN line when the SIP lines are busy.
The problem is, it connects to VLAN100 and gets its IP address and initializes fine however no lines show as configured and it can't make or receive calls. What do I need to configure on the SPA303 to tell it to use the SRP547W as its SIP Server/Proxy (not sure of the terminology).
View 4 Replies
View Related
Sep 25, 2011
my Networks contain three devices (BPX, DVR, PC) need to fixed IP, do you router supports the Cisco SRP547W Static Public ip.
View 1 Replies
View Related
May 24, 2012
I've purchased a router SRP547W and I would disable DHCP server. On the control panel I can't see anything about disabling this function. I don't need dhcp server on router and I don't need dhcp relay. My firmware version is 1.2.4_003.
View 4 Replies
View Related
Sep 10, 2011
We've run into some difficulty trying to take advantage of multiple WAN IPs in conjunction with the SRP547
What we're trying to acheive is the ability to port forward from our distinct public IPs to different internal servers. Looking at the options under Port Forwarding it looks like we can only configure forwards at the "WAN interface" level, but our problem is that we can't work out how to set up separate interfaces for each of our Public IPs...
Our ISP provides us with a fully managed NTU/router with a single "Internet" ethernet port, which we can use by statically configuring IPs on our end. For this configuration this port has been directly patched to the WAN ethernet port on the SRP547W.
We have been allocated a 255.255.255.248 (/29) subnet, giving us 5 usable IPs after the ISP's gateway address is taken into account, like so:
a.b.c.208 Network Address (/29 subnet)
a.b.c.209 ISP Gateway
a.b.c.210 IP1
[Code].....
I should mention at this point that we're running on firmware version 1.02.01 (023).
Is there a CLI or other method of configuration that might work if the web interface won't?
View 2 Replies
View Related
Feb 18, 2012
I have a SRP547W which I'm trying to replicate a configuration I had on an old Cisco 847 that recently died.
My ISP has allocated me a /29. The DSL configuration means that the IP address on the PPP session is assigned randomly. I have a mix of internal devices on a private IP range and a few devices with publically accessible addresses. All of the devices on the internal network need to be NATted to a public IP from the range allocated to me.
I can see that I can use the software or hardware DMZ to set up the servers, but I can't see any way to configure the external NAT address.
View 1 Replies
View Related
May 8, 2013
We've just purchased an SRP547W that we'd like to connect to our BT Infinity line. What the WAN configuration should be?
View 5 Replies
View Related
Feb 27, 2012
I have a SRP547W that I have configured the following way:
LAN 192.168.15.1/24 VLAN1
LAN 10.10.10.1/24 VLAN10
LAN 10.10.2.1/24 VLAN100
PPPOE ADSL
Software DMZ going to 10.10.10.x and another to 10.10.2.x - this is working OK
I now want to use the Advanced Firewall features to block all ports except those that I need as the software DMZ forwards everything. When I try to create the rules I get "the values are invalid" message no matter what I try.
I want to create explicit allow rules, followed by a deny all rule for each of the IP addresses used for the software DMZ
Have I got the Subnet Mask Correct for the Destination IP? Or should it be 255.255.255.0? It doesnt make a difference either way
Policy DetailsNameValueSource IP Address0.0.0.0Source Subnet Mask0.0.0.0Destination IP Address10.10.10.xDestination Subnet Mask255.255.255.254ProtocolAnySource PortAnyDestination Port443ActionPermitScheduleEverydayTimes24 Hours
View 6 Replies
View Related
Mar 27, 2011
I have an ADSL connection and have configured the PPPoE subinterface on WAN1 (ADSL) this connection has a static IP, and I know that the ISP gives that to me through DHCP however I have 4 or 5 additional IP addresses also provided to me on that same link, and they are not given to me via DHCP.
How do I configure this router to have multiple fixed IP addresses on a PPPoE interface?
I also need to port forward some ports for each of the IP's but I assume this will be easy after i have the IP addresses setup.
View 4 Replies
View Related
Aug 14, 2012
As per the title, I just require 3 to 4 VLANS with inter-VLAN communication enabled.
In the past I have used this router with each port of the internal switch set to a different VLAN, with each in turn hooked up to an unmanaged switch. This has work fine for me but I want to dip my toe in the world of .1q VLANS and gain some added flexibility and neatness.
View 3 Replies
View Related
Feb 13, 2013
I have recently purchases a Cisco srp547w for my organisation. It is working fine with one SSID enabled. I have configured everything with no problems using the Web interface. However, whenever I click the Edit button, in the Security column, in the Wireless Table under Basic Wireless Settings I get a pop up message which says :"Some values have been changed. The router must restart the wireless module to take effect.Please wait several seconds" I have tried this using 3 different browsers and get the same behaviour in each browser.
View 1 Replies
View Related
May 12, 2013
Ive changed the IP address of a laptop to connect to the router with IP 192.168.15.1 but now want to change the router IP address from the defaul to another subnet, so that it is accessable with other workstations on the LAN, but I could not readily find the option to set the Ip address on the router.
I'm signed in with user admin.
I also wanted to add addiontal users. The help indicates there is a User List Add Entry option but from the Administration bar, the left hand menu option shows User Management & User Privileges options. On User Management, it is possible to change the 2 default user names, but I wanted to leve them and create new ones.
View 2 Replies
View Related
Apr 7, 2012
I am trying to create a VPN between an SRP547W and a Cisco IOS router, in this case a UC540.I am running firmware 1.2.4 (003) Jan 11 2012. Now I can do this with an SRP527W and many other routers successfully. Including other IOS routers 1801, 1941 etc.
The issue I have is on the SRP547W I cannot create more than one IPSec Policy through a single IKE policy. I require this to route multiple v lans to our remote site. When I try to add an additional IPSec Policy I am give the error "IKE policy has been used by other IPSec policy"
This is possible to do on the SRP527W with latest firmware. I have tried rolling back to earlier firmware but instead I am given an error about overlap. Latest release note for this firmware suggest this issue was already resolved.
View 7 Replies
View Related
Jul 2, 2012
We have an ADSL2+ line from a WIC in a 1841, everything has been fine for the last few years and then the last few months the connection going down. When checking the interfaces the ATM0/0/0 is up up and the same for the dialer interface we are using, they are both up/up, but this still needs a reload of the router to be functional again, shutting the interfaces does not bring the connection back up.
I am not an expert on ADSL lines, I have never really had a problem with anything previously. The router was running Netflow to a network monitor wondering if this or logging was causing an issue with entries in the buffer??
Here is an output of show dsl int, would change the firmware, it has been fine all this time before though we are running IOS 12.4(24)T1 advseck9-m, as far as I can seen from our ISP the config for ADSL is all correct. [Code]
View 4 Replies
View Related
Mar 2, 2012
I have been having a weird connection issue for a week or so.The problem is at the first time i boot up my modem it simply cant connect.DSL Line LED keeps blinking- handshaking and training as it says in modem config page.After maybe 5 minutes or 2 hours, totally random.It picks up the connection, i can use it for hours until it randomly drops down once again.Ive contacted my ISP and they came over two times, they state the line quality is not suitable for my connection speed and it will be solved if i drop down my connection speed.Doing that is a painful process cause there is no other speed/quota package suitable for me, so i wanted to ask you people about it before i take action.
My modem is a Dynalink RTA1320 and i tried with another modem, tried mine in a friends house.Plus i went to the place where the cable enters my house and tried over there too, it didnt work as it should pick up in about 20 seconds.Here are stats my modem shows in the config page.[CODE]
View 4 Replies
View Related
Mar 19, 2013
The SRP547W supports creating both Wifi Voice and Data vlans.Can I configure a Wifi IP Phone to connect to the SRP547W Voice Wifi Vlan and have the SRP associate it with Line 1 (in lieu of a standard phone connected to the Line 1 FXO port - without additional hardware)?
View 1 Replies
View Related
Jul 6, 2012
Recently, i bought a LinkSys WAG120N ANNEX-A to replace my old speedstrem4200. Well everything was fine, but after 2 days of it installed, it started to drop my ADSL connection.
Sometimes, it remain connected for 4-5 hours, then drop, or sometimes, it drop every 30min-1hour.I tried upgrading the firmware to 1.00.16, but no luck, it still drop the connection.I have 3 computer plugged to the router via cable(wired) plus 1 netbook(wireless) and 1 ipod (wireless).Sometimes, when 1 computer is turned off, it seem to make the ADSL connection drop when the LAN light turn off. I noticed everytime it drop the ADSL connection, in the logs, i get this:
Mon, 2010-11-08 22:24:57 - Terminating on signal 15. Mon, 2010-11-08 22:24:57 - Enter: tdb_store. Mon, 2010-11-08 22:24:57 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_store. Mon, 2010-11-08 22:24:57 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_store. Mon, 2010-11-08 22:24:57 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_update. Mon, 2010-11-08 22:24:57 - Couldn't increase MTU to 1500. Mon, 2010-11-08 22:24:57 - Couldn't increase MRU to 1500 Mon, 2010-11-08 22:24:57 - LCP down. Mon, 2010-11-08 22:24:58 - Modem hangup Mon, 2010-11-08 22:24:58 - Connection terminated. Mon, 2010-11-08 22:24:58 - Connect time 215.0 minutes. Mon, 2010-11-08 22:24:58 - Sent 50496235 bytes, received 212267122 bytes. Mon, 2010-11-08 22:24:58 - Enter: tdb_store. Mon, 2010-11-08 22:24:58 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:58 - Enter: tdb_update. Mon, 2010-11-08 22:24:58 - Doing disconnect Mon, 2010-11-08 22:24:58 - Exit.
I tried changing the MTU settings in the router to 1492 (my ISP default) but didnt work.
Tried changing the MTU to 1492 on every computer and still got the same problem.For now im using the WAG120N in bridge mode, and still using my old speedstream4200 as ADSL modem.
View 5 Replies
View Related
Jan 11, 2010
I have bought a WAG320 & ever since I've had it the ADSL line keeps dropping every few hours. The LAN network is fine & I have 7 computers connected to the router wirelessly. When I press the re-set button on the back of the router everything is fine for a few hours then it starts doing it again?
View 9 Replies
View Related
Feb 7, 2013
I have a Netgear DG834G v3 ADSL router which I have had since early-2007.
When I work from home I connect to office networks on a Win7 machine via a Rackspace-provided VPN using Cisco System VPN Client 5. It works well, except for one issue that is costing me time every working day.
I get intermittently disconnected from the VPN, without any warning or apparent reason.
Since I bought the router 5-6 years ago I have had no need to update firmware, so other than ISP configuration I have had no need to change the router at all and I can say it's worked well for me.
What would be the reason for my VPN connection dropping? Is this an ISP issue (my ISP is Carphone Warehouse/TalkTalk) that I have to take up with them or is it more likely a hardware problem with my router or a VPN configuration issue?
My instincts are to not look into VPN config at the moment as I know a colleague who uses the same VPN through a different router and ISP can stay connected for hours, even overnight.
View 1 Replies
View Related
May 12, 2011
at our office we've recently upgrade from a old consumer-grade linksys wag200g modem/router/ap to the Cisco SRP527w. The Cisco is suffering from very frequent ADSL disconnections. These disconnections happens when there is some traffic to the internet and they seem to don't affect the LAN routing: on the weekends there are no disconnections at all while during the working hours there may be disconnections every FEW MINUTES making this router unusable. Often these disconnections force us to do a full reboot of the router.
Firmare version is SRP520W-1.1.19, the latest. ADSL line is a 6Mbps/640kbps. Noise margin is about 11dB for downstream and 20dB for upstream.
No voice line is used and therefore they are both disabled. 2 wireless network are active. The old linksys was (and is) working correctly, no adsl disconnections at all. Never.
View 40 Replies
View Related
