Cisco Routers :: How To Configure SRP547W To Support ANNEX M
Jan 18, 2012How to config SRP547W to support ANNEX M
View 4 Replies
ADVERTISEMENT
Cisco Routers :: USB Modems Support For SRP547W
Aug 9, 2011What is the current list of supported USB modems for the SRP547W router?
View 1 Replies View RelatedCisco Routers :: How To Change SRP 526W From Annex B To A
Sep 12, 2011some knows if is it possible to change the Annex from B to A in e SRP 526W model? Maybe using a firmware change/upgrade.
View 2 Replies View RelatedCisco Routers :: SRP547W Wi-Fi Drop Out
Apr 2, 2012i see that the wifi on the SRP Freezes. If i am connected via lan, i can still surf the net or connect to another access point on the network and surf. But the wiress devides connected to the SRP loose connectivity even though it shows that the wifi connection is connected. I am running on the latest firmware. this problem has started occcuring only recently
View 3 Replies View RelatedCisco Routers :: SRP547W - Multiple WAN IPs?
Mar 18, 2012There are a few discussions on this topic but nothing I can find indicated definativley shows that this can be done with this model.I have an ADSL service that came with 1 IP address and then we later purchased an additional 4 IPs (2 usable) for the same service.On our network we have SBS2011 and also a dedicated web server. What I would like to do is forward HTTPS to the web server on our inital IP and then forward https for OWA to one of the IPs on the additional set.Our initial IP is xxx.yyy.104.112 which I would like to forward port 443 to 192.168.0.12 - web server
The additional IPs are :
aaa.bbb.30.24 (Gateway Address)
aaa.bbb.30.25
aaa.bbb.30.26 - I would like to forward this to 192.168.0.2 - SBS box
aaa.bbb.30.27
I have tried as suggested in other thread setting up a software DMZ that sends public IP aaa.bbb.30.26 to 192.168.0.12. The xxx.yyy.104.112 to 192.168.0.12 works with a port 443 forward fine.
When I do this I cant connect from outside. If I change the port forward on 443 to go to 192.168.0.2 I can get to the SBS box from outside using the aaa.bbb.30.26 address .I have also tried creating a subinterface for the aaa.bbb.30.24 addresses and this also doesnot seem to work. Just I am basically asking for confirmation that this can be done with this model, I have put in the latest firmware.
Cisco Routers :: How To Administer SRP547W Over IPSec VPN
Sep 5, 2012I've got a network of SRP547Ws connected with site to site IPSec VPNs. But I can't get to the administrator loging page of the remote SRP547s over the VPN. Is there a setting or method I need to use ?
I have looked at the remote administration settings but this appears to be for adminsitration over the WAN interface rather the the IPSec VPN
Cisco Routers :: To Use Compatible 3G / 4G USB Modem Via SRP547W
May 29, 2012Currently, I have setup a demo lab with the UC320W + IP Phones and OnPlus Network Agent all connected to a SG300-28P. I have just obtained an SRP547W because I wanted to use the 3G/4G internet connection via the router as my demo lab is an isolated network.Now, I tried to a couple of 3G modem (UMG181) and 4G Telstra modem (MF821) on the SRP547W but none of these work. I had a look at the compatibility tableI guess those modem models are not listed there. However, when I went on say the Optus website to scout for a more compatible model, none of them hit it right on the mark. The matrix says it can support E180 (while Optus has the E188), E353 (while Optus has the E353). I have already wasted my money on getting the earlier stated 3G/4G Modems and I ain't going to take a chance again.
View 1 Replies View RelatedCisco Routers :: Voip With SRP547W And SPA303 Phones?
Oct 28, 2012I have an SRP547W hooked up as the office router with the standard office phones connected via the telephone ports at the back of the unit using 2 SIP lines as well as the PSTN by dialling hash first. We have just added a new staff member and bought an SPA303 with the intention of connecting it through registered SIP lines on the SRP547W, and hopefully have the facility to use the PSTN line when the SIP lines are busy.
The problem is, it connects to VLAN100 and gets its IP address and initializes fine however no lines show as configured and it can't make or receive calls. What do I need to configure on the SPA303 to tell it to use the SRP547W as its SIP Server/Proxy (not sure of the terminology).
Cisco Routers :: SRP547W Multi Static Public Ip?
Sep 25, 2011my Networks contain three devices (BPX, DVR, PC) need to fixed IP, do you router supports the Cisco SRP547W Static Public ip.
View 1 Replies View RelatedCisco Routers :: How To Disable DHCP Server On SRP547W
May 24, 2012I've purchased a router SRP547W and I would disable DHCP server. On the control panel I can't see anything about disabling this function. I don't need dhcp server on router and I don't need dhcp relay. My firmware version is 1.2.4_003.
View 4 Replies View RelatedCisco Routers :: SRP547W - How To Use Multiple WAN IPs For Port Forwarding
Sep 10, 2011We've run into some difficulty trying to take advantage of multiple WAN IPs in conjunction with the SRP547
What we're trying to acheive is the ability to port forward from our distinct public IPs to different internal servers. Looking at the options under Port Forwarding it looks like we can only configure forwards at the "WAN interface" level, but our problem is that we can't work out how to set up separate interfaces for each of our Public IPs...
Our ISP provides us with a fully managed NTU/router with a single "Internet" ethernet port, which we can use by statically configuring IPs on our end. For this configuration this port has been directly patched to the WAN ethernet port on the SRP547W.
We have been allocated a 255.255.255.248 (/29) subnet, giving us 5 usable IPs after the ISP's gateway address is taken into account, like so:
a.b.c.208 Network Address (/29 subnet)
a.b.c.209 ISP Gateway
a.b.c.210 IP1
[Code].....
I should mention at this point that we're running on firmware version 1.02.01 (023).
Is there a CLI or other method of configuration that might work if the web interface won't?
Cisco Routers :: SRP547W Dropping ADSL Every Minute
Feb 22, 2012We installed one of these devices as our gateway a couple of weeks ago, flashed the firmware to 1.2.4(003) and it worked perfectly until this morning where it keeps resetting the ADSL every minute and losing the web interface to the unit.
The log endlessly reports this:
Feb 24 11:26:00 SRP547W cron.info cron[8779]: (root) CMD (/sbin/check_gn)
Feb 24 11:26:00 SRP547W cron.info cron[8781]: (root) CMD (/sbin/check_ps)
[Code].....
Cisco Routers :: SRP547W - Selecting NAT IP From Static Range
Feb 18, 2012I have a SRP547W which I'm trying to replicate a configuration I had on an old Cisco 847 that recently died.
My ISP has allocated me a /29. The DSL configuration means that the IP address on the PPP session is assigned randomly. I have a mix of internal devices on a private IP range and a few devices with publically accessible addresses. All of the devices on the internal network need to be NATted to a public IP from the range allocated to me.
I can see that I can use the software or hardware DMZ to set up the servers, but I can't see any way to configure the external NAT address.
Cisco Routers :: SRP547W - LAN Configuration For Connecting To BT Infinity Line?
May 8, 2013We've just purchased an SRP547W that we'd like to connect to our BT Infinity line. What the WAN configuration should be?
View 5 Replies View RelatedCisco Routers :: SRP547W Cannot Create Advanced Firewall Rules
Feb 27, 2012I have a SRP547W that I have configured the following way:
LAN 192.168.15.1/24 VLAN1
LAN 10.10.10.1/24 VLAN10
LAN 10.10.2.1/24 VLAN100
PPPOE ADSL
Software DMZ going to 10.10.10.x and another to 10.10.2.x - this is working OK
I now want to use the Advanced Firewall features to block all ports except those that I need as the software DMZ forwards everything. When I try to create the rules I get "the values are invalid" message no matter what I try.
I want to create explicit allow rules, followed by a deny all rule for each of the IP addresses used for the software DMZ
Have I got the Subnet Mask Correct for the Destination IP? Or should it be 255.255.255.0? It doesnt make a difference either way
Policy DetailsNameValueSource IP Address0.0.0.0Source Subnet Mask0.0.0.0Destination IP Address10.10.10.xDestination Subnet Mask255.255.255.254ProtocolAnySource PortAnyDestination Port443ActionPermitScheduleEverydayTimes24 Hours
Cisco Routers :: Multiple Fixed IP Addresses On PPPoE With SRP547W
Mar 27, 2011 I have an ADSL connection and have configured the PPPoE subinterface on WAN1 (ADSL) this connection has a static IP, and I know that the ISP gives that to me through DHCP however I have 4 or 5 additional IP addresses also provided to me on that same link, and they are not given to me via DHCP.
How do I configure this router to have multiple fixed IP addresses on a PPPoE interface?
I also need to port forward some ports for each of the IP's but I assume this will be easy after i have the IP addresses setup.
Cisco Routers :: Router On A Stick VLAN With SRP547w And SG200
Aug 14, 2012As per the title, I just require 3 to 4 VLANS with inter-VLAN communication enabled.
In the past I have used this router with each port of the internal switch set to a different VLAN, with each in turn hooked up to an unmanaged switch. This has work fine for me but I want to dip my toe in the world of .1q VLANS and gain some added flexibility and neatness.
Cisco Routers :: SRP547W - Can't Ping External Side Of ADSL Interface
Mar 2, 2013I have installed a couple of SRP547W's and can't ping the external side of the ADSL interface.
Is there an option to turn on "respond to ping" and also are you able to forward to a internal IP?
Cisco Routers :: Srp547w Restarts When Edit Security In Wireless Table?
Feb 13, 2013I have recently purchases a Cisco srp547w for my organisation. It is working fine with one SSID enabled. I have configured everything with no problems using the Web interface. However, whenever I click the Edit button, in the Security column, in the Wireless Table under Basic Wireless Settings I get a pop up message which says :"Some values have been changed. The router must restart the wireless module to take effect.Please wait several seconds" I have tried this using 3 different browsers and get the same behaviour in each browser.
View 1 Replies View RelatedCisco Routers :: SRP547w - Change Default IP And Create Additional Users
May 12, 2013Ive changed the IP address of a laptop to connect to the router with IP 192.168.15.1 but now want to change the router IP address from the defaul to another subnet, so that it is accessable with other workstations on the LAN, but I could not readily find the option to set the Ip address on the router.
I'm signed in with user admin.
I also wanted to add addiontal users. The help indicates there is a User List Add Entry option but from the Administration bar, the left hand menu option shows User Management & User Privileges options. On User Management, it is possible to change the 2 default user names, but I wanted to leve them and create new ones.
Cisco Routers :: SRP547W Multiple IPSec Policies Through Single IKE Policy
Apr 7, 2012I am trying to create a VPN between an SRP547W and a Cisco IOS router, in this case a UC540.I am running firmware 1.2.4 (003) Jan 11 2012. Now I can do this with an SRP527W and many other routers successfully. Including other IOS routers 1801, 1941 etc.
The issue I have is on the SRP547W I cannot create more than one IPSec Policy through a single IKE policy. I require this to route multiple v lans to our remote site. When I try to add an additional IPSec Policy I am give the error "IKE policy has been used by other IPSec policy"
This is possible to do on the SRP527W with latest firmware. I have tried rolling back to earlier firmware but instead I am given an error about overlap. Latest release note for this firmware suggest this issue was already resolved.
Cisco Routers :: SRP547W IP Phone Access To Line Number Via Wi-Fi Voice Vlan?
Mar 19, 2013The SRP547W supports creating both Wifi Voice and Data vlans.Can I configure a Wifi IP Phone to connect to the SRP547W Voice Wifi Vlan and have the SRP associate it with Line 1 (in lieu of a standard phone connected to the Line 1 FXO port - without additional hardware)?
View 1 Replies View RelatedCisco Routers :: SRP547W Site-to-site VPN With L2TP Over ADSL
Oct 25, 2011I'm installing a new SRP547W for a client and am having trouble setting up a site-to-site vpn. They are using the WAN1 ADSL interface for their internet connection. When I add a sub interface to it I am unable to see the 'Connection Type' drop down like I can see on a WAN2 ethernet sub interface. I have followed the instructions on page 29 provided here: how I can get a a site to site vpn set up on this router using either PPTP or L2TP over the ADSL interface.
View 1 Replies View RelatedCisco WAN :: 886VA Gets No Link With Annex-J
Mar 2, 2013i used a Cisco 886VA with Annex-B service in Germany. Now the provider has changed the DSLAM port to Annex-J but the router does not get any connection anymore.
As per Cisco homepage [URL] the router should support Annex-J in table 7:
Cisco 886VA: Optimized for Annex B; also compatible with Annex J
How to bring up the router with Annex-J service?? Is there something special i have to configure? Do i have to buy Cisco 886VA-J???
Software i have tested:
==========================================
c880data-universalk9-mz.151-4.M4.bin
c880data-universalk9-mz.153-1.T.bin
[Code].....
Linksys Cable / DSL :: WAG200G Change From Annex B To A
Mar 4, 2007Possible using a firmware upgrade to change the wag200g from annex B to annex A?T
View 6 Replies View RelatedLinksys Cable / DSL :: WAG160N Which Version Annex A Or B
Nov 15, 2011I havce a WAG160N that is still on firmware version V1.00.16 andf I want to update it to the latest version. I have seen on url...WAG160N that there is two versions to download - Annex A and Annex B under version 2.0.
View 3 Replies View RelatedLinksys Cable / DSL :: WAG160N Annex A V.1 - Reboot Device To Let Mac Map
Apr 1, 2013As you can see in the subject that is my configuation, i always need to reboot the device to let my mac map the nas on finder
after the reboot nas is mapped.
The second problem is that i need to reboot the device if i want to use Remote App on my iphone to remote control itunes again after rebooting romote app on iphone connects to iTunes.
Linksys Cable / DSL :: X3000 Works With Annex B Connection?
Sep 26, 2011i have a Linksys x3000 DSL modem/router. I need to set up an Annex B DSL connection. Is it possible to chance the modem to Annex B using firmware?
View 9 Replies View RelatedConfigure AP (WAP4410N) To Support Roaming?
Jul 7, 2011How can i configure AP (WAP4410N) to Support Roaming?
View 2 Replies View RelatedLinksys Cable / DSL :: X2000 Version 1 Annex A Firmware Not Downloadable
Nov 6, 2012I tried to download the new firmware version (2.0.04) for Linksys x2000 hw version 1 Annex A: error 404 page not found.Same issue with 2 different machines on different internet connections.
View 3 Replies View RelatedCisco WAN :: Configure 2821 To Support 4G / LTE Backup Circuit
Apr 17, 2012how to configure the 2nd WAN port to support 4G/LTE connectivity that will serve as the backup circuit to the primary MPLS circuit?
View 2 Replies View RelatedCisco WAN :: 3560 - Configure L3 To Support ISCSi Traffic
Nov 14, 2011I would like to properly configure my L3 to support iSCSi traffic. My L3 acts as an internal router between 4 different sub nets.
I have a iSCSi SAN on my network. A Windows server has Microsoft iSCSi initiators connecting to the SAN.
Linksys Cable / DSL :: Switch AM200 Adsl Modem To Annex B Mode?
Dec 6, 2006how to switch AM200 adsl modem to AnnexB mode, in Slovakia working only AnnexB
View 2 Replies View Related