Linksys Cable / DSL :: X3000 Works With Annex B Connection?
Sep 26, 2011i have a Linksys x3000 DSL modem/router. I need to set up an Annex B DSL connection. Is it possible to chance the modem to Annex B using firmware?
View 9 Replies
ADVERTISEMENT
Linksys Cable / DSL :: Connection Between X3000 And Vodafone SureSignal
Jan 22, 2012Got a Vodafone SureSignal (VSS) to work with a Linksys router/modem ? My X3000 is to replace a Belkin N1 which had an intermittent fault. My VSS worked fine with the Belkin and required no additional setup, however since connecting to my X3000 is just will not connect.I have tried to manually forward all ports as suggested just in case but no matter what I try it refuses to sync and connect through the VPN tunnel. This is a link to the vodafone setup guide: SureSignal setup,Just for sanity sake I have reconnected my old Belkin and it then connects again in a couple of minutes, so it is definitely a setup issue with my X3000.s this is getting very frustrating and I cannot believe a VSS cannot work with the leading brand of router.
View 3 Replies View RelatedLinksys Cable / DSL :: Cisco X3000 Keeps Loosing Internet Connection?
Sep 19, 2012My Cisco X3000 keeps loosing the internet connection after 1 day and will only reconnect if the device is rebooted. Pressing the Internet connect button in the Status page does nothing.Even when the Internet connection is lost, the wireless network is working 100% and all the devices on the network stays connected and are accessible.The router has been updated to the latest Firmware available from Cisco v1.0.03 build 001 Jun 11,2012
View 9 Replies View RelatedLinksys Cable / DSL :: WAG200G Change From Annex B To A
Mar 4, 2007Possible using a firmware upgrade to change the wag200g from annex B to annex A?T
View 6 Replies View RelatedLinksys Cable / DSL :: WAG160N Which Version Annex A Or B
Nov 15, 2011I havce a WAG160N that is still on firmware version V1.00.16 andf I want to update it to the latest version. I have seen on url...WAG160N that there is two versions to download - Annex A and Annex B under version 2.0.
View 3 Replies View RelatedLinksys Cable / Dsl :: X3000 - Check Control Panel To See Webpages Viewed On Wifi Connection
Apr 6, 2013i have a linksys x3000 router, is there anyway of getting into the routers control panel to see the previous webpages that have been viewed over the wifi connection?
View 3 Replies View RelatedLinksys Cable / DSL :: WAG160N Annex A V.1 - Reboot Device To Let Mac Map
Apr 1, 2013As you can see in the subject that is my configuation, i always need to reboot the device to let my mac map the nas on finder
after the reboot nas is mapped.
The second problem is that i need to reboot the device if i want to use Remote App on my iphone to remote control itunes again after rebooting romote app on iphone connects to iTunes.
Linksys Cable / DSL :: X2000 Version 1 Annex A Firmware Not Downloadable
Nov 6, 2012I tried to download the new firmware version (2.0.04) for Linksys x2000 hw version 1 Annex A: error 404 page not found.Same issue with 2 different machines on different internet connections.
View 3 Replies View RelatedLinksys Cable / DSL :: Switch AM200 Adsl Modem To Annex B Mode?
Dec 6, 2006how to switch AM200 adsl modem to AnnexB mode, in Slovakia working only AnnexB
View 2 Replies View RelatedLinksys Cable / DSL :: Get 300 Mbps With X3000?
Aug 8, 2012Got 300 Mbps with Linksys X3000 in real life?I haven't seen it working at 300 Mbps since I've bought it, so I wonder whether it is truly possible. The maximum speed I've seen was 130 Mbps.
View 7 Replies View RelatedLinksys Cable / DSL :: X3000 Log Is Not Working?
Oct 1, 2012Log enabled using [URL] , config saved, modem power cycled...... no in and out log after internet use.
View 1 Replies View RelatedLinksys Cable / DSL :: X3000 With DD-WRT Support?
Apr 14, 2013I'm currently researching in buying a new modem/router that must have the PPPoA support for the ISP, i'm wondering if the X3000 is compatible with the DD-WRT firmware? or in this case any other firmware that has a top notch QoS, We have a troll in the house that downloads too many torrents and would like to limit his bandwidth .
View 1 Replies View RelatedLinksys Cable / DSL :: X3000 Internet Access Via LAN?
Nov 11, 2012Over the passed couple of weeks I have experienced issues trying to connect to the internet via the LAN Ports. My main PC and a Xbox cannot connect to the internet even though 3 laptops have no problems using the Wifi connectivity.I have had two live chats with Cisco engineers and the first resolution was to perform a firmware upgrade which did solve the issue for a day or two. I think it was more to do with reset the modem/router rather than the firmware upgrade. The second session ended with the eingineer advising me to take the equipment back to PC and seek a replacement simply because Ciso have nothing in writing relating to this problem.
View 6 Replies View RelatedLinksys Cable / DSL :: X3000 Cannot Connect To ADSL
Dec 12, 2011I just bought a Linksys X3000 to work with my ADSL connection (provider is Singtel from Singapore). I managed to use Cisco connection application to logon and setup the router OK, yesterday. I even connected my PC to the router by LAN, and also a few devices wirelessly.At the end of the day, I switched off everything... but next morning, when I booted up the router, I found that all my devices cannot access internet. Upon checking the server (192.168.1.1), I found that it does not have a IP from Singtel, although on the router the internet symbol (globe sign) is lighted up.I rebooted the router twice, getting the same results (note: I waited for a long time each time, until the globe was lighted up).I disconnected the X3000, and reconnected my Netgear DGN2000. It worked (and retrieved an IP address from Singtel). I then disconnected the Netgear and reconnected X3000. To my surprise, this time X3000 got the IP address and then internet is working again.
View 9 Replies View RelatedLinksys Cable / DSL :: Current Time Not Available X3000?
Oct 13, 2012regarding Current Time Not Available. I loose internet connecting for hte last 5 weeks, My ISP is good. Bit I have noticed Current Time Not Available and when this happens my internet looses connection. but does state still connected. Using v1.0.03 build 001 Jun 11,2012 can we set manually the time?
View 9 Replies View RelatedLinksys Cable / DSL :: X3000 Why Not Download Firmware Ver.1.0.04
Dec 20, 2012X3000 why not download firmware Ver.1.0.04?
View 3 Replies View RelatedLinksys Cable / DSL :: X3000 Missing DSL Parameters
May 4, 2012Following the chat with the technical support of CISCO.In few words, the LINKSYS X3000 is the only router in the world that can't shows the DSL line parameters ( SNR and LINE ATTENIATION ) so you can't evaluate the line quality without using another router.... INCREDIBLE!!!!Let's see how long it will be before the firmware update!Me: simple question: is rather embarrassing but I can't find the SNR value (Adsl status) in the Linksys X3000 interface. Same for the Line Attenuation values. These are the standard DSL information and they are essential to evaluate the DSL line quality.Unfortunately, you are right, these parameters are not available on the Gateway (X3000) Setup page.Me:It's unbelievable I use routers for my work and this is the first product that can't shows the DSL line parameters...The only parameters available under DSL Connection Subta are Status, Downstream Rate and Upstream Rate.Me:Do you think it's serious? The price of this product and the target to which it is oriented suggest a more professional approach.I agree, but as of now, this is how it is however, you need to keep an eye on future updates for the device that might include these paraters/features.Me:Please could you send a notification to the DEVELOP TEAM to quickly update this product FIRMWARE and close the gap that separates it from other products in the same category?
View 9 Replies View RelatedLinksys Cable / DSL :: ICMP Packets From Outside X3000
Apr 18, 2012At this moment we have a Linksys x3000 configured as modem on a ADSL connection (PPPoA)From our monitoring server we send ICMP packets to see if the connection is alive (or not).The problem is when we disable the ipV4 SP1 firewall and do not tick the: "Filter Anonymous Internet Requests" , we still receive connection timeout's from outside hosts. Is this a bug? And if not; how can we enable ping from outside networks?We really want to enable ping because of the monitoring software.The firmware is the latest version: 1.0.0.1
View 7 Replies View RelatedLinksys Cable / DSL :: X3000 Not Compatible With EA4500?
Apr 28, 2013The Linksys EA4500 router is designed to be added to an existing network as an additional access point. See the following description:
Setting your Linksys Wi-Fi or Smart Wi-Fi Router to Bridge Mode is applicable when you want to:• Connect two (2) routers with the capability of sharing the network resources • Use the router as an additional access point on an existing network • Connect the router to a modem/router from your Internet Service Provider (ISP) • Disable the router functionalities to work with third party devices
http:[url].....
Unfortunately the Linksys X3000 DSL modem router is not compatible to the bridge mode, since the internal switch fails if a MAC address of a wireless device switches between the X3000 internal access point and the access point of the EA4500 router. In the faulty state, no local network resources (print server, NAS, ...) are accessible anymore.
Linksys Cable / DSL :: USB Drive Keeps Dropping Off X3000
May 11, 2012I recently changed my wireless ADSL router to an X3000. One of the main reasons for doing so was its ability to share a disk drive on the network without having to have a computer powered on to host the drive. This has been working OK for a month or two, but now the drive keeps "disappearing".
What I mean is that when a computer tries to access it over the network, it gets a message that the network name cannot be found. If I then log into the router, under the Storage section, there are no drive details showing. I have rebooted the router, and sometimes this restores the situation, sometimes not. Sometimes I have to unplug and replug the USB cable, then do a reboot. The USB drive is a 500GB Western Digital FreeAgent Desktop drive. There is nothing wrong with the drive - if I connect it directly to a computer it all works fine. Typically it drops off overnight. We can be accessing the drive OK on a couple of laptops in the evening, then next morning, "network name not found". The router and the drive remain powered on all the time.
As I said it has worked OK for a month or two, now it appears flakey and very unreliable. This router takes a very long time to reboot, so having to do it often is painful.
Linksys Cable / DSL :: X3000 Can't Set Broadcast IP From Web Interface
Oct 17, 2012I tried to set my x3000 (firmware 1.0.03) to wake up on internet my pc. This is my configuration:IP lan 192.168.1.10 (fixed on pc and reserved in DHCP)Firewall: forward port 9 from WAN to LAN IP.I can't set broadcast IP (192.168. 1. 255) from web interface.I also tried this solutions but without success: url...
View 9 Replies View RelatedLinksys Cable / DSL :: X3000 - Can't Access Web Interface
Apr 21, 2012I am using the x3000 as a modem and router, and I managed to set up the device yesterday through the web interface (192.168.1.1).However, after less than 24 hours of continuous usage, I cannot access the interface for some odd reason. I tried using the disk that came with the device but the software reports as if I am not connected to the router. I tried pinging 192.168.1.1 and I get >1 ms so that confirms the device is active and responsive.
View 1 Replies View RelatedLinksys Cable / DSL :: What Chipset Is Installed In X3000
Sep 26, 2012What chipset is installed inside linksys X3000 router? I tried, but i can't find this:/
View 2 Replies View RelatedLinksys Cable / DSL :: X3000 - Able To Ping IPs But Not Hostnames
Oct 3, 2012We have a brand new Linksys X3000, with the latest firmware installed. It does not recognise the hostnames of devices on our network. We have added a few hostnames, using 'manually add client'. My first question is why would it not recognise hostnames (a variety of devices, e.g. phones, apple time machine, linux PCs)?
The next problem is that that we are successfully able to ping IP addresses, but when we ping hostnames, results are inconsistent. e.g. currently I have my laptop and a time machine connected by wire directly to the router. I can ping the time machine by IP. The first time I ping by hostname, it works, but immediately after that I ping again and it says 'unknown host'. Why would it suddently forget about a device it is clearly connected to? Have we got some sort of default security setting I don't know about?
Linksys Cable / Dsl :: X3000 Wifi Getting Low Signal
Nov 27, 2012I've bought X3000 modem recently & the only issue is pops up for me is wifi signal is too low. I've got 2 routers with me. My old linksys router WAG200G has got no issues with wifi signal. I kept both routers at the same place & compared with same standard channel yet what astonishing me that WAG200G has got more stability than X3000 regardless inspite changing to wireless -N. Is there a way to solve it. Btw, I tried all the standard channels yet it doesn't make any difference.
Firmware Version: v1.0.01.
Linksys Cable / DSL :: X3000 Is Not Compatible With EA4500?
Feb 14, 2013The Linksys EA4500 router is designed to be added to an existing network as an additional access point. See the following description:Setting your Linksys Wi-Fi or Smart Wi-Fi Router to Bridge Mode is applicable when you want to:• Connect two (2) routers with the capability of sharing the network resources • Use the router as an additional access point on an existing network • Connect the router to a modem/router from your Internet Service Provider (ISP) • Disable the router functionalities to work with third party devices [URL]Unfortunately the Linksys X3000 DSL modem router is not compatible to the bridge mode, since the internal switch fails if a MAC address of a wireless device switches between the X3000 internal access point and the access point of the EA4500 router. In the faulty state, no local network resources (print server, NAS, ...) are accessible anymore.
View 6 Replies View RelatedLinksys Cable / DSL :: How To Connect Fiber Box To X3000
Apr 2, 2013 I have X3000 home gateway and very happy with this device. Use it now as ADSL modem/wifi router. Everything works fine but there is something I do not understand about this device.It has 4 LAN ports and a Cable port. Suppose, I am upgraing from a copper service to fibre. Fibre providers comes and installs their fibre box which is kind of a "modem" for fibre technology. how do I connect fibre box to X3000? Do I use Cable port or a LAN port?
As far as I understand the 4 LAN ports work as switch ports (work at OSI level 2, provide access strictly within same subnet, all devices connected to these ports share the same default gateway), and Cable port gets a different IP address via DHCP or another protocol from the fibre box, or directly from ISP (if we have PPPoE or IPoE service as an example). And there would be no point in plugging WAN link into a LAN port as X3000 would not be able to communicate to the gateway on the other end of the cable.
Linksys Cable / DSL :: X3000 ADSL Line Down
Nov 21, 2012I have ADSL router Linksys X3000, but I have an issue with it. I have configured it properly (based on internet provider's manual), repeatedly checked it, but router still says that ADSL line is down. I have also another router from Zyxel and it works perfect with same wire and configuration, so I guess the line is fine.
PPP generic driver version 2.4.2 79 PPP Deflate Compression module registered 88 PPP BSD Compression module registered 84 PPPoL2TP kernel driver, V1.0 75 ccp_autowan_sm_thread=> Starts in Unconfigured mode, detecting state! 125 ->
[Code]....
Linksys Cable / DSL :: X3000 Used As A Router Behind A VDSL Modem
Nov 10, 2012I desperately try to set up the X3000 as a router behind a vDSL modem. When I choose connection through Ethernet and then PPPoE, it never keep the credentials after reboot in spite of having saved the data before.
View 6 Replies View RelatedLinksys Cable / DSL :: Updating X3000 Modem Router
Jul 8, 2012I recently purchased two x3000 devices.Both shipped with the 1.0.01 firmware installed.Upgraded one device in one location to the 1.0.03.001 release without issue.A day later i'm not trying from a second location to perform the same action.I've downloaded the FW_X3000_1.0.03.001.bin firmware from the Cisco downloads for the device and receive a pop up 'The image file is incorrect'.I've downloaded hte image twice and it appears to be correct in size. I'm following the same process that worked without issue the day previously.
View 3 Replies View RelatedLinksys Cable / DSL :: Possible To Have Multi PVC For IP TV In X3000 Adsl Router?
Aug 28, 2012Is it possible to have multi PVC for IP TV in x3000 adsl router ?
View 1 Replies View RelatedLinksys Cable / DSL :: Add X3000 To SingTel 2 Wire 5012NV?
Nov 19, 2011I'm looking to add the X3000 to my SingTel 2Wire 5012NV to be able to increase the wireless speed to 100Mbps and also an extender RE1000 to cover some blind spots int he house. How to configure the 5012NV into a bridge so this will work for me without loosing the connection from the 5012NV to the mioTV setup box and phone line.
View 1 Replies View RelatedLinksys Cable / DSL :: X3000 Requires Daily Restart?
Feb 3, 2012I have a Linksys X3000 router. While it is running, connection latency will gradually increase over about a day until eventually it just stops working at all and I have to power it off and back on again.
Ping times to a local website slowly increase from 30ms immediately after restarting the router, to about 100ms about an hour before it will need to be restarted, then rapidly increase to over 1 second before it drops out completely. When this happens, no connections through the router will work, I cannot even ping it or connect to its configuration web page.
I upgraded the firmware to see if that would work but it didn't. I have had the exact same problems with the 1.0.0 and 1.0.01 versions.
Can I get it replaced? And in the mean time, is there some way to make the router automatically restart at a scheduled time?