i have a linksys x3000 router, is there anyway of getting into the routers control panel to see the previous webpages that have been viewed over the wifi connection?
View 3 Repliesfirst connect to configuration page is very slow
Second issue: after updating to FW 1.0.4 any web pages doesn't accept any passwords. I can not login to some sites. After reset to Factory defaults I can not configure router - password for ISP doesnt accepted and saved... so internet doesn't work. After rolling back FW all configuret and works fine
when i enter 2 Access Restrictions & add put some data After a period of time Control Panel crashes
View 6 Replies View RelatedI've bought X3000 modem recently & the only issue is pops up for me is wifi signal is too low. I've got 2 routers with me. My old linksys router WAG200G has got no issues with wifi signal. I kept both routers at the same place & compared with same standard channel yet what astonishing me that WAG200G has got more stability than X3000 regardless inspite changing to wireless -N. Is there a way to solve it. Btw, I tried all the standard channels yet it doesn't make any difference.
Firmware Version: v1.0.01.
The X3000 functions as a router/gateway between the ADSL network, its wireless network (WPA2) and its wired network. After a cold start, factory reset and restore of the config file everything works fine. I have interconnection between all three parts of my network. However after ± 24 hour there is no connection possible anymore from the wired to the wireless network and vice versa. A normal power off - power on will not work. The only thing that works is running the factory reset procedure as discribed above. I changed the MTU to manual 1400 as was suggested on this forum, but that does not work. Apart from this issue, ADSL is hicks sometimes. From my ISP I heard that at certain times my router issues ten's of DHCP requests within one minute, while the connection (modem) remains perfect. I have the impression that after such a DHCP request storm to my ISP, the interconnection between my X3000 wireless network and my X3000 wired network is lost.
View 4 Replies View Relatedi have a Linksys x3000 DSL modem/router. I need to set up an Annex B DSL connection. Is it possible to chance the modem to Annex B using firmware?
View 9 Replies View RelatedGot a Vodafone SureSignal (VSS) to work with a Linksys router/modem ? My X3000 is to replace a Belkin N1 which had an intermittent fault. My VSS worked fine with the Belkin and required no additional setup, however since connecting to my X3000 is just will not connect.I have tried to manually forward all ports as suggested just in case but no matter what I try it refuses to sync and connect through the VPN tunnel. This is a link to the vodafone setup guide: SureSignal setup,Just for sanity sake I have reconnected my old Belkin and it then connects again in a couple of minutes, so it is definitely a setup issue with my X3000.s this is getting very frustrating and I cannot believe a VSS cannot work with the leading brand of router.
View 3 Replies View RelatedMy Cisco X3000 keeps loosing the internet connection after 1 day and will only reconnect if the device is rebooted. Pressing the Internet connect button in the Status page does nothing.Even when the Internet connection is lost, the wireless network is working 100% and all the devices on the network stays connected and are accessible.The router has been updated to the latest Firmware available from Cisco v1.0.03 build 001 Jun 11,2012
View 9 Replies View RelatedWhen I first installed my wireless router a few years ago, I did it with my old computer which has Windows XP as its operating system. It is on this computer that the Linksys "admin control panel" is installed, which allows me see what computers are connected through the router, see what the settings of the router are, etc. I recently purchased a new computer which has Windows 7 as the operating system. As I transfer programs and documents from my old computer to my new computer, I have run into the problem of how to transfer the Linksys "admin control panel" from my old computer to my new computer. The original installation CD for Linksys won't work with Windows 7 so I don't even have that as a starting point. I tried going to the web-based admin site, but can't access it from either computer.
View 8 Replies View RelatedI've just upgraded my home wireless from an NetComm NB5540 + modem to a LinkSys X3000.Internet access works fine for all devices, but some wireless devices can't "see" my Win7 desktop system that's on a wired connections to the router. Galaxy Note phone (running ICS 4.0.4) can discover and connect to file shares on my desktop system without any problems.Asus Transformer Prime tablet (running JellyBean 4.1.1) can see the router on the local network, but can't see my desktop. Even if I manually type in the IP address it can't connect to itLikewise my old WinXP laptop can see the router but can't see or connect to any other devices.
I tried connecting the NetComm router with just Wifi configured to one of the ethernet ports on the X3000, so I've got two Wifi networks running in parallel. If I connect to this second WiFi network with any of the above devices then they can all discover and connect to my desktop system on the wired connection to the X3000.
I can not get to my control panel. I have tried 192.168.1.1 and 192.168.0.1,. I do have it flashed with DD-wrt. I can access the internet with it, the lights look correct, I don,t believe it is bricked. I have tried hard reset and soft reset.
View 5 Replies View RelatedI just installed Windows XP Professional on my Toshiba-X205 laptop and I am having a problem getting the OS to detect my NIC. I can not remember how to go into the control panel and configure settings so the OS will detect my wireless network or should i say i can not get my OS to detect my NIC so i can to connect to my wireless network. I think i may need to install the device driver for the NIC but i don't remember which driver i need for the NIC of my laptop and i can not find it on the Toshiba website, not supported anymore.
View 1 Replies View RelatedI set a password and everything on my n300's Netgear Genie, but every time I go to routerlogin or 10.0.0.1, it just shows me the full control panel and never prompts me to log in. Isn't security a bit too lax over there? I even click log out and it says i logged out, then I re-visit and I'm always automatically logged in.
View 3 Replies View RelatedHere is the setup: A US Robotics USR-9108 router is connected to an ADSL modem via ethernet cable. The modem, upon connecting with the ISP, provides a gateway address of 192.168.1.1 to the router. End-users including me connect to the internet through the router via WiFi and are assigned the IP 192.168.1.2...192.168.1.255.
When disconnected from the modem, I can access the control panel via 192.168.3.1 but once the ethernet cable is plugged in I cannot access the above-mentioned IP; connecting to 192.168.1.1 opens up the modem's control panel. Any possible way to access the router control panel while it is connected to the internet?
I am holding a DPC 3925 Cable Modem to connect to the internet. The wireless is great and all but i need something more.I need to connect another 8 cat6a cables to it to complete my home network. should i use a switch or patch panel or something?And not all 8 cable will be on wired. One or two connections are needed to extend the range of the wifi. What device can i use?I've got a ps3, NAS and media box that probably need the network connections to the main DPC 3925 Cable Modem.
View 1 Replies View Relatedproblems with laptop, one of which is i am unable to get wireless connection again, no network connections are appearing in control panel?
View 5 Replies View Relatedjust i purchase cisco access point and I tried to access control panel to setup wireless security but the page i issued not display 192.168.1.245, there is any wayes to connet device web base ??
View 4 Replies View RelatedI'm having trouble connecting via ethernet to my WAG200G. Everything was working fine a week ago but now, nothing.The problem is only occurring with one computer and I've tried the troubleshooting guide on the website to no avail.When I connect the ethernet cable from my computer to the modem/router, I don't get a light on the front panel on any of the ports. I've changed cables, ports, disabled ZoneAlarm and firewalls and nothing comes up. I've checked the ethernet connection from the computer to another computer and it's working fine.
On a different computer, I have no trouble connecting to the ports and can confirm that 1-4 are working and the lights come up.
I have wag320n router (FM ver. 1.00.08), some webpages (for example [URL]) don't load, but several load (for example yandex.ru). By changing MTU value on my PC I can solve this problem and this sites will load properly. But can't do this on my mobile devices (for example smartphone, PSP) and I have to set MTU value on each computer, connected to my network. So I want to find out, how solve this problem on the "level" of the router.
View 8 Replies View RelatedGot 300 Mbps with Linksys X3000 in real life?I haven't seen it working at 300 Mbps since I've bought it, so I wonder whether it is truly possible. The maximum speed I've seen was 130 Mbps.
View 7 Replies View RelatedLog enabled using [URL] , config saved, modem power cycled...... no in and out log after internet use.
View 1 Replies View RelatedI'm currently researching in buying a new modem/router that must have the PPPoA support for the ISP, i'm wondering if the X3000 is compatible with the DD-WRT firmware? or in this case any other firmware that has a top notch QoS, We have a troll in the house that downloads too many torrents and would like to limit his bandwidth .
View 1 Replies View RelatedRegion : Others
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :
I am struggling to get a printer added through the print server. The printer is set up in the TP-Link USB Printer Controller and selected as the auto-connect printer. I can scan through the server, but can't add the printer in control panel or see it as a option when printing. The printer is a Samsung SCX-340F.
Over the passed couple of weeks I have experienced issues trying to connect to the internet via the LAN Ports. My main PC and a Xbox cannot connect to the internet even though 3 laptops have no problems using the Wifi connectivity.I have had two live chats with Cisco engineers and the first resolution was to perform a firmware upgrade which did solve the issue for a day or two. I think it was more to do with reset the modem/router rather than the firmware upgrade. The second session ended with the eingineer advising me to take the equipment back to PC and seek a replacement simply because Ciso have nothing in writing relating to this problem.
View 6 Replies View RelatedI just bought a Linksys X3000 to work with my ADSL connection (provider is Singtel from Singapore). I managed to use Cisco connection application to logon and setup the router OK, yesterday. I even connected my PC to the router by LAN, and also a few devices wirelessly.At the end of the day, I switched off everything... but next morning, when I booted up the router, I found that all my devices cannot access internet. Upon checking the server (192.168.1.1), I found that it does not have a IP from Singtel, although on the router the internet symbol (globe sign) is lighted up.I rebooted the router twice, getting the same results (note: I waited for a long time each time, until the globe was lighted up).I disconnected the X3000, and reconnected my Netgear DGN2000. It worked (and retrieved an IP address from Singtel). I then disconnected the Netgear and reconnected X3000. To my surprise, this time X3000 got the IP address and then internet is working again.
View 9 Replies View Relatedregarding Current Time Not Available. I loose internet connecting for hte last 5 weeks, My ISP is good. Bit I have noticed Current Time Not Available and when this happens my internet looses connection. but does state still connected. Using v1.0.03 build 001 Jun 11,2012 can we set manually the time?
View 9 Replies View RelatedX3000 why not download firmware Ver.1.0.04?
View 3 Replies View RelatedFollowing the chat with the technical support of CISCO.In few words, the LINKSYS X3000 is the only router in the world that can't shows the DSL line parameters ( SNR and LINE ATTENIATION ) so you can't evaluate the line quality without using another router.... INCREDIBLE!!!!Let's see how long it will be before the firmware update!Me: simple question: is rather embarrassing but I can't find the SNR value (Adsl status) in the Linksys X3000 interface. Same for the Line Attenuation values. These are the standard DSL information and they are essential to evaluate the DSL line quality.Unfortunately, you are right, these parameters are not available on the Gateway (X3000) Setup page.Me:It's unbelievable I use routers for my work and this is the first product that can't shows the DSL line parameters...The only parameters available under DSL Connection Subta are Status, Downstream Rate and Upstream Rate.Me:Do you think it's serious? The price of this product and the target to which it is oriented suggest a more professional approach.I agree, but as of now, this is how it is however, you need to keep an eye on future updates for the device that might include these paraters/features.Me:Please could you send a notification to the DEVELOP TEAM to quickly update this product FIRMWARE and close the gap that separates it from other products in the same category?
View 9 Replies View RelatedAt this moment we have a Linksys x3000 configured as modem on a ADSL connection (PPPoA)From our monitoring server we send ICMP packets to see if the connection is alive (or not).The problem is when we disable the ipV4 SP1 firewall and do not tick the: "Filter Anonymous Internet Requests" , we still receive connection timeout's from outside hosts. Is this a bug? And if not; how can we enable ping from outside networks?We really want to enable ping because of the monitoring software.The firmware is the latest version: 1.0.0.1
View 7 Replies View RelatedThe Linksys EA4500 router is designed to be added to an existing network as an additional access point. See the following description:
Setting your Linksys Wi-Fi or Smart Wi-Fi Router to Bridge Mode is applicable when you want to:• Connect two (2) routers with the capability of sharing the network resources • Use the router as an additional access point on an existing network • Connect the router to a modem/router from your Internet Service Provider (ISP) • Disable the router functionalities to work with third party devices
http:[url].....
Unfortunately the Linksys X3000 DSL modem router is not compatible to the bridge mode, since the internal switch fails if a MAC address of a wireless device switches between the X3000 internal access point and the access point of the EA4500 router. In the faulty state, no local network resources (print server, NAS, ...) are accessible anymore.
I recently changed my wireless ADSL router to an X3000. One of the main reasons for doing so was its ability to share a disk drive on the network without having to have a computer powered on to host the drive. This has been working OK for a month or two, but now the drive keeps "disappearing".
What I mean is that when a computer tries to access it over the network, it gets a message that the network name cannot be found. If I then log into the router, under the Storage section, there are no drive details showing. I have rebooted the router, and sometimes this restores the situation, sometimes not. Sometimes I have to unplug and replug the USB cable, then do a reboot. The USB drive is a 500GB Western Digital FreeAgent Desktop drive. There is nothing wrong with the drive - if I connect it directly to a computer it all works fine. Typically it drops off overnight. We can be accessing the drive OK on a couple of laptops in the evening, then next morning, "network name not found". The router and the drive remain powered on all the time.
As I said it has worked OK for a month or two, now it appears flakey and very unreliable. This router takes a very long time to reboot, so having to do it often is painful.
I tried to set my x3000 (firmware 1.0.03) to wake up on internet my pc. This is my configuration:IP lan 192.168.1.10 (fixed on pc and reserved in DHCP)Firewall: forward port 9 from WAN to LAN IP.I can't set broadcast IP (192.168. 1. 255) from web interface.I also tried this solutions but without success: url...
View 9 Replies View RelatedI am using the x3000 as a modem and router, and I managed to set up the device yesterday through the web interface (192.168.1.1).However, after less than 24 hours of continuous usage, I cannot access the interface for some odd reason. I tried using the disk that came with the device but the software reports as if I am not connected to the router. I tried pinging 192.168.1.1 and I get >1 ms so that confirms the device is active and responsive.
View 1 Replies View Related