Cisco Routers :: SRP547W - LAN Configuration For Connecting To BT Infinity Line?
May 8, 2013We've just purchased an SRP547W that we'd like to connect to our BT Infinity line. What the WAN configuration should be?
View 5 Replies
ADVERTISEMENT
Cisco Routers :: SRP547W IP Phone Access To Line Number Via Wi-Fi Voice Vlan?
Mar 19, 2013The SRP547W supports creating both Wifi Voice and Data vlans.Can I configure a Wifi IP Phone to connect to the SRP547W Voice Wifi Vlan and have the SRP associate it with Line 1 (in lieu of a standard phone connected to the Line 1 FXO port - without additional hardware)?
View 1 Replies View RelatedRouters / Switches :: Connecting 30 PCs To A T1 Line And 1 Workgroup
Feb 7, 2011I have a building with 30+ pc's, printers and cameras. I do not have a "server" setup, however I want them to be connected to the T1 line comming into the building for internet as well as file sharing, etc.Currently, I have the T1 line connecting to as Linksys E3000 wireless router. From there I have a cable connected to the wireless router (it has 4 ports also) and then going to a Netgear FS524 (24 Port 10/100 MBPS Fast Ethernet Switch) via port number 24. I then have another CAT5 cable connected to a port on this switch, extending to a D-Link DES-1024D (another 24 Port, 10/100 switch)I then have the 30+ CAT5 cable coming into all three of said devices... No then, I get Internet connection on all units, the problem is that I cannot see all of the devices.
View 2 Replies View RelatedConnecting 2 Routers Through One Phone Line On Different Sockets
Aug 4, 2011I've seen loads of people connecting 2 routers, but they're usually connecting the routers together (as in connecting 1 router to another, which is connected to both the internet and the PC) to boost the performance of the current router, or connect more devices. What seems to be hard to find is what I want to do.
The situation is, I have a Sky Broadband Router (a specialised Sagem router from Sky Broadband ISP) in the back room of my house, and it's wireless range can't reach the front room of my house (where I want to use my wireless laptop). Moving the router is not an option, so I purchased a Belkin 300N Router and plugged it into another phone socket at the front of the house (the phone line was originally just at the front of the house, but was extended to another socket at the back of the house, the one the Sky Router is connected to).
The router is working, but seems to be clashing with the Sky Router, it can't connect unless I turn the Sky Router off, and the Sky router always overrides the Belkin one. I've seen some posts about syncing routers when they're connected, but these aren't, they're just on the same phone line, how to stop them clashing?
I got told if I changed the IP address of the Belkin Router to one similar to the Sky one, and disabled DCHP it would work, but this just messed the Belkin Router up and I had to give it a factory reset!
Belkin Routers :: Does The F9K1113 Work With BT Infinity
Apr 1, 2013Does the F9K1113 work with BT Infinity? I have tried to get this to work but I cannot
View 2 Replies View RelatedRouters / Switches :: Connecting DSL Modem Router To RJ45 Line?
Oct 29, 2012I just got a DSL Modem router (DSL 2750U) which has DSL input for internetconnectivity.My internet service provider provides RJ45 Cable which needs LAN input socket on a router for internet connectivity. How do I connect?
View 4 Replies View RelatedCisco Routers :: SRP547W Wi-Fi Drop Out
Apr 2, 2012i see that the wifi on the SRP Freezes. If i am connected via lan, i can still surf the net or connect to another access point on the network and surf. But the wiress devides connected to the SRP loose connectivity even though it shows that the wifi connection is connected. I am running on the latest firmware. this problem has started occcuring only recently
View 3 Replies View RelatedCisco Routers :: SRP547W - Multiple WAN IPs?
Mar 18, 2012There are a few discussions on this topic but nothing I can find indicated definativley shows that this can be done with this model.I have an ADSL service that came with 1 IP address and then we later purchased an additional 4 IPs (2 usable) for the same service.On our network we have SBS2011 and also a dedicated web server. What I would like to do is forward HTTPS to the web server on our inital IP and then forward https for OWA to one of the IPs on the additional set.Our initial IP is xxx.yyy.104.112 which I would like to forward port 443 to 192.168.0.12 - web server
The additional IPs are :
aaa.bbb.30.24 (Gateway Address)
aaa.bbb.30.25
aaa.bbb.30.26 - I would like to forward this to 192.168.0.2 - SBS box
aaa.bbb.30.27
I have tried as suggested in other thread setting up a software DMZ that sends public IP aaa.bbb.30.26 to 192.168.0.12. The xxx.yyy.104.112 to 192.168.0.12 works with a port 443 forward fine.
When I do this I cant connect from outside. If I change the port forward on 443 to go to 192.168.0.2 I can get to the SBS box from outside using the aaa.bbb.30.26 address .I have also tried creating a subinterface for the aaa.bbb.30.24 addresses and this also doesnot seem to work. Just I am basically asking for confirmation that this can be done with this model, I have put in the latest firmware.
Cisco Routers :: How To Administer SRP547W Over IPSec VPN
Sep 5, 2012I've got a network of SRP547Ws connected with site to site IPSec VPNs. But I can't get to the administrator loging page of the remote SRP547s over the VPN. Is there a setting or method I need to use ?
I have looked at the remote administration settings but this appears to be for adminsitration over the WAN interface rather the the IPSec VPN
Cisco Routers :: To Use Compatible 3G / 4G USB Modem Via SRP547W
May 29, 2012Currently, I have setup a demo lab with the UC320W + IP Phones and OnPlus Network Agent all connected to a SG300-28P. I have just obtained an SRP547W because I wanted to use the 3G/4G internet connection via the router as my demo lab is an isolated network.Now, I tried to a couple of 3G modem (UMG181) and 4G Telstra modem (MF821) on the SRP547W but none of these work. I had a look at the compatibility tableI guess those modem models are not listed there. However, when I went on say the Optus website to scout for a more compatible model, none of them hit it right on the mark. The matrix says it can support E180 (while Optus has the E188), E353 (while Optus has the E353). I have already wasted my money on getting the earlier stated 3G/4G Modems and I ain't going to take a chance again.
View 1 Replies View RelatedCisco Routers :: USB Modems Support For SRP547W
Aug 9, 2011What is the current list of supported USB modems for the SRP547W router?
View 1 Replies View RelatedCisco Routers :: How To Configure SRP547W To Support ANNEX M
Jan 18, 2012How to config SRP547W to support ANNEX M
View 4 Replies View RelatedCisco Routers :: Voip With SRP547W And SPA303 Phones?
Oct 28, 2012I have an SRP547W hooked up as the office router with the standard office phones connected via the telephone ports at the back of the unit using 2 SIP lines as well as the PSTN by dialling hash first. We have just added a new staff member and bought an SPA303 with the intention of connecting it through registered SIP lines on the SRP547W, and hopefully have the facility to use the PSTN line when the SIP lines are busy.
The problem is, it connects to VLAN100 and gets its IP address and initializes fine however no lines show as configured and it can't make or receive calls. What do I need to configure on the SPA303 to tell it to use the SRP547W as its SIP Server/Proxy (not sure of the terminology).
Cisco Routers :: SRP547W Multi Static Public Ip?
Sep 25, 2011my Networks contain three devices (BPX, DVR, PC) need to fixed IP, do you router supports the Cisco SRP547W Static Public ip.
View 1 Replies View RelatedCisco Routers :: How To Disable DHCP Server On SRP547W
May 24, 2012I've purchased a router SRP547W and I would disable DHCP server. On the control panel I can't see anything about disabling this function. I don't need dhcp server on router and I don't need dhcp relay. My firmware version is 1.2.4_003.
View 4 Replies View RelatedCisco Routers :: SRP547W - How To Use Multiple WAN IPs For Port Forwarding
Sep 10, 2011We've run into some difficulty trying to take advantage of multiple WAN IPs in conjunction with the SRP547
What we're trying to acheive is the ability to port forward from our distinct public IPs to different internal servers. Looking at the options under Port Forwarding it looks like we can only configure forwards at the "WAN interface" level, but our problem is that we can't work out how to set up separate interfaces for each of our Public IPs...
Our ISP provides us with a fully managed NTU/router with a single "Internet" ethernet port, which we can use by statically configuring IPs on our end. For this configuration this port has been directly patched to the WAN ethernet port on the SRP547W.
We have been allocated a 255.255.255.248 (/29) subnet, giving us 5 usable IPs after the ISP's gateway address is taken into account, like so:
a.b.c.208 Network Address (/29 subnet)
a.b.c.209 ISP Gateway
a.b.c.210 IP1
[Code].....
I should mention at this point that we're running on firmware version 1.02.01 (023).
Is there a CLI or other method of configuration that might work if the web interface won't?
Cisco Routers :: SRP547W Dropping ADSL Every Minute
Feb 22, 2012We installed one of these devices as our gateway a couple of weeks ago, flashed the firmware to 1.2.4(003) and it worked perfectly until this morning where it keeps resetting the ADSL every minute and losing the web interface to the unit.
The log endlessly reports this:
Feb 24 11:26:00 SRP547W cron.info cron[8779]: (root) CMD (/sbin/check_gn)
Feb 24 11:26:00 SRP547W cron.info cron[8781]: (root) CMD (/sbin/check_ps)
[Code].....
Cisco Routers :: SRP547W - Selecting NAT IP From Static Range
Feb 18, 2012I have a SRP547W which I'm trying to replicate a configuration I had on an old Cisco 847 that recently died.
My ISP has allocated me a /29. The DSL configuration means that the IP address on the PPP session is assigned randomly. I have a mix of internal devices on a private IP range and a few devices with publically accessible addresses. All of the devices on the internal network need to be NATted to a public IP from the range allocated to me.
I can see that I can use the software or hardware DMZ to set up the servers, but I can't see any way to configure the external NAT address.
Cisco Routers :: SRP547W Cannot Create Advanced Firewall Rules
Feb 27, 2012I have a SRP547W that I have configured the following way:
LAN 192.168.15.1/24 VLAN1
LAN 10.10.10.1/24 VLAN10
LAN 10.10.2.1/24 VLAN100
PPPOE ADSL
Software DMZ going to 10.10.10.x and another to 10.10.2.x - this is working OK
I now want to use the Advanced Firewall features to block all ports except those that I need as the software DMZ forwards everything. When I try to create the rules I get "the values are invalid" message no matter what I try.
I want to create explicit allow rules, followed by a deny all rule for each of the IP addresses used for the software DMZ
Have I got the Subnet Mask Correct for the Destination IP? Or should it be 255.255.255.0? It doesnt make a difference either way
Policy DetailsNameValueSource IP Address0.0.0.0Source Subnet Mask0.0.0.0Destination IP Address10.10.10.xDestination Subnet Mask255.255.255.254ProtocolAnySource PortAnyDestination Port443ActionPermitScheduleEverydayTimes24 Hours
Cisco Routers :: Multiple Fixed IP Addresses On PPPoE With SRP547W
Mar 27, 2011 I have an ADSL connection and have configured the PPPoE subinterface on WAN1 (ADSL) this connection has a static IP, and I know that the ISP gives that to me through DHCP however I have 4 or 5 additional IP addresses also provided to me on that same link, and they are not given to me via DHCP.
How do I configure this router to have multiple fixed IP addresses on a PPPoE interface?
I also need to port forward some ports for each of the IP's but I assume this will be easy after i have the IP addresses setup.
Cisco Routers :: Router On A Stick VLAN With SRP547w And SG200
Aug 14, 2012As per the title, I just require 3 to 4 VLANS with inter-VLAN communication enabled.
In the past I have used this router with each port of the internal switch set to a different VLAN, with each in turn hooked up to an unmanaged switch. This has work fine for me but I want to dip my toe in the world of .1q VLANS and gain some added flexibility and neatness.
Cisco Routers :: SRP547W - Can't Ping External Side Of ADSL Interface
Mar 2, 2013I have installed a couple of SRP547W's and can't ping the external side of the ADSL interface.
Is there an option to turn on "respond to ping" and also are you able to forward to a internal IP?
Cisco Routers :: Srp547w Restarts When Edit Security In Wireless Table?
Feb 13, 2013I have recently purchases a Cisco srp547w for my organisation. It is working fine with one SSID enabled. I have configured everything with no problems using the Web interface. However, whenever I click the Edit button, in the Security column, in the Wireless Table under Basic Wireless Settings I get a pop up message which says :"Some values have been changed. The router must restart the wireless module to take effect.Please wait several seconds" I have tried this using 3 different browsers and get the same behaviour in each browser.
View 1 Replies View RelatedCisco Routers :: SRP547w - Change Default IP And Create Additional Users
May 12, 2013Ive changed the IP address of a laptop to connect to the router with IP 192.168.15.1 but now want to change the router IP address from the defaul to another subnet, so that it is accessable with other workstations on the LAN, but I could not readily find the option to set the Ip address on the router.
I'm signed in with user admin.
I also wanted to add addiontal users. The help indicates there is a User List Add Entry option but from the Administration bar, the left hand menu option shows User Management & User Privileges options. On User Management, it is possible to change the 2 default user names, but I wanted to leve them and create new ones.
Cisco Routers :: SRP547W Multiple IPSec Policies Through Single IKE Policy
Apr 7, 2012I am trying to create a VPN between an SRP547W and a Cisco IOS router, in this case a UC540.I am running firmware 1.2.4 (003) Jan 11 2012. Now I can do this with an SRP527W and many other routers successfully. Including other IOS routers 1801, 1941 etc.
The issue I have is on the SRP547W I cannot create more than one IPSec Policy through a single IKE policy. I require this to route multiple v lans to our remote site. When I try to add an additional IPSec Policy I am give the error "IKE policy has been used by other IPSec policy"
This is possible to do on the SRP527W with latest firmware. I have tried rolling back to earlier firmware but instead I am given an error about overlap. Latest release note for this firmware suggest this issue was already resolved.
Connecting To Another PC Via Command Line?
Apr 14, 2011My grandma has a PC with Windows XP, she uses it only for Skype calls. can go in to her PC using command line from my PC? What commands should I use and what modifications to do on my grandma's PC? Should I ask permission from grandma's ISP (which is the same as mine)?
View 3 Replies View RelatedCisco :: 2911 Connecting To A Leased Line?
Aug 3, 2012I have a cisco 2911 set up at one of my sites and it is configured with sub-interfaces as this provides a default gateway to each of the offices.I have just had a 100mb leased line put in and i have a couple of questions regarding the config.let me start by telling you how it is set up .I have 3 HP Procurve switches connected together then that connects to the Cisco and the Cisco connects to a Zywall
HP Switches > Cisco 2911 > Zywall > Internet
We are wanting to remove the Zywall and connect the Cisco to the Leased line box
HP Switches > Cisco 2911 > Leased Line > Internet
The config of the cisco is
G0/0 - is up but no cable connected as this holds the sub-interfaces
G0/1 - Connects the Zywall - 192.168.1.1 (this has firewall rules to forward traffic through)
G0/2 - Leased Line
The way i have configured the sub interfaces is with its own DHCP pool and default router, some of the offices have there own ADSL router and hold there own Internet connection and the default gateway for that is 192.168.xxx.253 and the offices that use the Cisco use default gateway of 192.168.xxx.254
Now my question is how would I move everyone onto the Leased line and get rid of the Zywall ? Would it be as simple as giving the leased line an address and put in a static route to forward all traffic through that connection ? Or am i missing a trick or 2.
Connecting Two Modem With One Phone Line?
Jan 31, 2013that possible to connect one telephone line with two modem (both are wireles)if possible then how?
View 1 Replies View RelatedCisco Routers :: SRP547W Site-to-site VPN With L2TP Over ADSL
Oct 25, 2011I'm installing a new SRP547W for a client and am having trouble setting up a site-to-site vpn. They are using the WAN1 ADSL interface for their internet connection. When I add a sub interface to it I am unable to see the 'Connection Type' drop down like I can see on a WAN2 ethernet sub interface. I have followed the instructions on page 29 provided here: how I can get a a site to site vpn set up on this router using either PPTP or L2TP over the ADSL interface.
View 1 Replies View RelatedConnecting Cisco Linksys Router To RCT Line Interactive UPS?
Aug 9, 2012I just bought a new Cisco Linksys router and RCT Line interactive UPS i just want to connect my router to the UPS the UPS has ports for line in and line out but my router only has a line in. What do i do i thought about connecting the line in directly to the UPS and the line out from the UPS to the router only using telephone cables there is no power cable from the router thats going to be attached to the UPS.
View 1 Replies View RelatedConfiguration Of Internet Leased Line?
Dec 28, 2011I got following IP address from BSNL to configure Internet leased line.OFC cable was terminated at our premises. it has to connect Ethernet port.Say eg.Wan IP : 192.168.1.6 255.255.255.252Public address pool : 172.168.10.6 to 12if i configure one address on Ethernet port1 as nat outside 192.168.1.6 255.255.255.252.the ip address given for wan & pool are different.Then how can i configure pool and how to configure nat inside eg 185.168.10.1 to 255the above ip are not actual ips just given for example.
View 6 Replies View RelatedCisco VPN :: 3000 - How To Get Running Configuration Through Command Line
Jul 13, 2011command to get running config of Cisco VPN 3000 concentrator.
View 3 Replies View RelatedCisco WAN :: 2621 / 3600 / 5505 - Work With BT Infinity
Mar 20, 2012We have an existing Cisco 2621 XM router with an ADSL interface connected to BT Broadband. Basic layout below:
Internet------ADSL on Cisco 2621 ------ Pix 506e ---- 3600 switch with inter VLAN routing to multiple VLANS
There are 5 static IP addresses. The internal FE port on the 2621 has one external assigned to it. The outside int of the PIX has another external IP assigned from the 5. The other 3 are NATd through to internal IPs via the PIX to internal servers etc.
The ADSL is being upgraded to BT Infinity. This new service comes with a separate VDSL modem and a separate BT router. Ideally I want to ignore the BT router and use the Cisco 2621 as it has 2 FE ports and I suspect I could do something using PPPOE.
So New layout would look like
Internet ----- BT VDSL modem------ Cisco 2621 ----- Pix 506e ---- 3600 switch with interVLAN routing to multiple VLANS
I think it is a bit strange the way it is setup as 2 static IPs cant be used. There is an opportunity to use a ASA 5505 which may become available.