Configure AP (WAP4410N) To Support Roaming?
Jul 7, 2011How can i configure AP (WAP4410N) to Support Roaming?
View 2 Replies
ADVERTISEMENT
Cisco Routers :: RV180W Add Access Point With Roaming Support?
Oct 20, 2012I have a customer with a RV180w running the latest firmware. We are currently using the router as a router and to provide wireless access. We want to add wireless coverage and I am interested in our options. We have a ethernet backbone which we could use to give the new AP LAN connectivity. Can we buy another RV180W and use it in AP mode and provide roaming wireless connectivty. The client wants a guest and business WLAN so we will use the VLAN feature of the router. How do we configure the new AP? Do we need to use WDS? If we use WDS, can we still use WPA2?
View 6 Replies View RelatedCisco Wireless :: WAP4410N Best Way To Set Up Wireless For Roaming RDP User
Mar 6, 2013I am trying to resolve a wireless issue for a busy medical office I work at; it is an 11,000 sf building with many exam rooms and offices, and 20-30 wireless users. We tried placing three WAP4410N devices around the building on different channels with a shared SSID, so that users would have connectivity anywhere in the building. The medical assistants and doctors connect to their EMR software using laptops connected via RDP and we seem to have an issue with connections dropping briefly when they move throughout the building. The disruption is enough that their RDP connections often become unresponsive and they have to take time to disconnect and reconnect again. The other issue is that the laptops would jump to a stronger signal when, for instance, a nurse walked to the front of the building to get a patient and came close to a different WAP, but then when they came back to the exam area, the device would hang onto that signal as it grew very weak instead of jumping back to the closer WAP.
We've also had issues with the a couple of the devices becoming completely unresponsive but I am hoping the firmware update will fix that. Is there a way to make this work properly with this model of router? How many devices should we need for full coverage? If they just aren't up to this task, what should we be looking at to replace them? From what I have been able to research, what we are looking for is 'seamless roaming' and these devices don't support that. But I was told by a support tech that even the Aironet WAPs will have a few dropped packets going between APs so I would hate to upgrade yet again and still have the problem remain.
Cisco Wireless :: WAP4410N Support For CDP Or LLDP?
Sep 5, 2012Does the WAP4410N access point for Small Businesses support any Discovery Protocol like Cisco Discovery Protocol (CDP) or Link-Layer Discovery Protocol (LLDP), both for sending and receiving frames? I did an extensive search on the manuals and I was unable to find it
View 1 Replies View RelatedCisco Wireless :: Does WAP4410N Support Guest Access?
Sep 13, 2011Does the Linksys AP (WAP4410N) support Wireless Guest access solution?
View 2 Replies View RelatedCisco Wireless :: Can't Configure SSID More Than One In Web UI Of WAP4410N
Oct 12, 2011I can't configure the SSID more than one in the web UI of the WAP4410N. Except I can type the first SSID1, the rest SSID2 - 4 are grey which not allow me to type in anything. ( See attached the screen shot ) My current version is 2.02.1 and I was using IE8 under windows 7.
View 3 Replies View RelatedCisco Wireless :: Configure WAP4410N With Multiple SSIDS
Jan 10, 2012I need to configure a WAP4410N for use on a small, very simple business network. There should be a corporate WLAN and a guest WLAN. The corporate WLAN should allow anyone connectd to it to access resources on the domain.
In front of the WAP is a cable modem/router and a basic Level 2 (web managed) switch. What do i have to do to segregate the corporate and guest networks.
I thought I would add the corporate WLAN to VLAN1 (assuming the default VLAN in the switch is VLAN1). Then I figured I could create the guest WLAN and assign it to VLAN2 which which will be controlled entirely by the 4410N (DHCP, DNS, etc.) Does this sound like the right way of going about things?
Cisco Wireless :: Configure Two AP WAP4410N In Bridge Mode?
Jun 16, 2011I want to configure two AP WAP4410N in Bridge Mode and I don´t find the correct configuraction tips.
View 11 Replies View RelatedCisco Wireless :: WAP4410N / Configure Dhcp Or Client?
Sep 11, 2011WAP4410N / configure dhcp OR dhcp CLIENT?
View 3 Replies View RelatedCisco Wireless :: Setting To Configure Only To Surf Internet Through WAP4410N
Sep 22, 2011I need to configure WAP4410N wireless access point for our company guest and visitors.i need them to only surf internet and not to go to LAN (servers).I think i need to create VLAN for this ? can any one tell me setting for configure only to surf internet thru WAP4410N ?
View 1 Replies View RelatedLinksys Wireless Router :: Does Cisco WAP4410N Wireless-N Access Point Support PPPoE
Feb 21, 2013Does Cisco WAP4410N Wireless-N Access Point support PPPoE ?If yes how can I configure the PPPoE conexion?
View 1 Replies View RelatedCisco Wireless :: Configure Multiple SSID With Multiple VLANs And DHCP Pool WAP4410N
Sep 18, 2012My question is if I can configure 3 ssid, for 3 different VLAN and add the DHCP address from a WAP4410N AP, when you upgrade to the latest version of IOS I can have this functionality?
View 2 Replies View RelatedCisco Wireless :: 802.11 WAP4410N To WAP4410N Backhaul Using N Protocol?
Apr 30, 2011I have the following equipment:
Cisco 871W router
2x WAP 4410N APs running 2.0.3.3
I currently have 1 AP connected to the router via copper. The AP to AP link is over 802.11. I have attached a diagram reflecting the current topology.
The AP-to-AP link will come up utilizing B/G/N mixed mode; however, the connection is basically unusable. About 30% of the traffic is dropped, while the packets that do make it have a consistently volatile latency, anywhere from 15 to 1500 ms. I have had success using G-only and B/G mixed. The link is stable (I have had the best results with B/G). The problem is, I didn't buy the 2nd 4410N to run the G protocol. I would like to connect the APs running either B/G/N (hopefully negotiating to N) or N only. I am wondering if there is a certain configuration I can utilize (perhaps using WDS repeater or bridge versus Wireless Client/Repeater?), or a firmware upgrade set for release that can make this happen for me.
Cisco Routers :: How To Configure SRP547W To Support ANNEX M
Jan 18, 2012How to config SRP547W to support ANNEX M
View 4 Replies View RelatedCisco WAN :: Configure 2821 To Support 4G / LTE Backup Circuit
Apr 17, 2012how to configure the 2nd WAN port to support 4G/LTE connectivity that will serve as the backup circuit to the primary MPLS circuit?
View 2 Replies View RelatedCisco WAN :: 3560 - Configure L3 To Support ISCSi Traffic
Nov 14, 2011I would like to properly configure my L3 to support iSCSi traffic. My L3 acts as an internal router between 4 different sub nets.
I have a iSCSi SAN on my network. A Windows server has Microsoft iSCSi initiators connecting to the SAN.
Cisco WAN :: How To Configure Router 2900 To Support Connection From 2 Firewall
Jun 24, 2012how to configure a router 2900 to support connection from 2 firewall ( Active Standby connections) How can i said the router to send the traffic to the stand by when it go down the active Firewall?I was planning to use a Switch ( layer 2 capacity only) in the middle of the equipments ( between the firewalls and the router) in order to send always the traffic for 1 physical interface from the router side , and manage to route all the internatl traffic to the virtual IP of both Firewalls.Also i dont know yet how to configure a VPN site to site if i have that scheme and some Publics NAT ( Firewall - Switch - Router ), i was planning to configure a NAT in the Router in order to allow the VPN traffic to internal IP of the Firewall but still dont know if it will work.
View 2 Replies View RelatedCisco Switching/Routing :: Configure Nexus 5596 To Support Proper QoS For EF At The Core?
Feb 23, 2012I am deploying a pair of Nexus 5596's with 3750 POE switches in the closets. I'm looking for a best practice as how to configure the Nexus 5596 to support proper QoS for EF at the core.
View 6 Replies View RelatedWAP 4410 N - Wireless Roaming
Apr 21, 2012I have 5 access points (WAP4410N) all connected to a befsr41 8 port/switch router, each AP has it's own SSID. Is it possible to to have one SSID for the entire wireless network so users do not have to change SSID's every time they change locations?
View 11 Replies View RelatedTo Create Roaming Wifi Network
May 1, 2012how to create WiFi network with uninteruptable roaming between Access Points while clients are moving.What hardware is the best here? Are there any manuals about that?
View 2 Replies View RelatedRoaming Network With Multiple WAPs?
Sep 27, 2011Just checking in to ask about setting up a network with multiple WAPs. Right now, I have it set up with two WAPs, and can roam seemlessly between the two. Same security, SSIDs, etc. I have one broadcasting on channel 1, and the other on channel 11.What I wanted to ask is this: in the future, I'd like to add two wireless access to a different network that exists in the same building. So I'd have two more WAPs, broadcasting a different network with a different SSID. I can assign one to channel 6, but the last WAP will not have a non-overlapping channel to use. Is that going to cause interference issues?
View 2 Replies View RelatedWifi Rendered Useless By Roaming?
Mar 2, 2012How can I allow AND prevent connection to wireless networks based on their BSSID(MAC Address), when their SSID(default/custom name) is the same and changing SSID is absolutely NOT an option? Physicaly moving closer to the Preferred Network Wireless Access Point is also absolutely NOT an option. i.e.
Allow connect/reconnect to:
SSID - Linksys
BSSID - AA-AA-AA-AA-AA-AA
and
Prevent connection to:
SSID - Linksys
[code]....
Roaming Wireless Network With Different Brands?
Feb 28, 2012Is it possible to set up a roaming wireless network with wireless access points that are different brands from one another (i.e., D-Link, Cisco, Belkin, etc.)? If so, is there anything special that needs to be configured?
View 2 Replies View RelatedWireless Access Point Roaming?
May 30, 2011But my laptop often times changes access points as I move about in my office to try to optimize the signal strength, which causes the network to stop working and I had to do "ipconfig -renew" to continue using internet. Problem now is that the IT desk told me that the AP's are overloaded.
View 1 Replies View RelatedLinksys Cable / DSL :: Use Two WAG120N As Roaming WLAN?
Jan 31, 2011We have a customer who has a WAG120N as their broadband wireless router, and we've sold them some new equipment, part of which is another WAG120N as our salesperson didn't realise they had one.They have a section of the building which the current WAG120N will not reach. Reading around this forum, it seems that I can give the second WAG120N a different static IP on the LAN and use it to expand the range of the WLAN.If I've read correctly, I need to make all the wireless stuff exactly the same except to use different wireless channels on each router. But what do I do with the DHCP server on the second WAG? Is it fair to say that the clients won't suddenly jump to a different IP because they won't have a cause to request a new one? I read one comment that suggested the second should be configured for DHCP relay, and another which contradicted this. Presumably I just don't configure the ADSL on the second WAG as that will only connect to the LAN.
View 3 Replies View RelatedCisco Wireless :: 5508 - How To Change WLC / Roaming
Jul 21, 2011I have more different client networks with one ssid, when a client is in another network gets an ip it still from the old network.
How can I to the wlc change this so he gets one right address. I have a Cisco WLC 5508 and 1262/1252 Access point
Cisco Wireless :: 5508 Roaming From AP On Same SSID
Feb 12, 2013I have an issue where I have an AP in one room and another in another.When I walk from one room to the other, I lose signal but manages to see the SSID and join.But, I cannot seem to surf the Internet, I have to manually disconnect and reconnect. Normal wireless routers I reconnect seamlessly without any manual disconnect & reconnect.Currently using cisco 5508 and ap2600.
View 8 Replies View RelatedCisco Wireless :: UC540 Roaming Does Not Seem To Work
Mar 1, 2012I currently have a UC540 system with 12x aironet 1130 APs. Seamless roaming does not seem to work, and the recommendation seems to be to introduce a WLAN controller.
View 4 Replies View RelatedCisco Wireless :: Best Configuration To Improve Roaming In WLC 7.3
Apr 22, 2013I´m trying to find the best configuration to improve the roaming in a WLC 7.3I changed the power threshold under the TPC to -67 and in the client roaming I put in custom mode and the minimun RSSI in -78 dBm.but I was wondering if there is a specific configuration to improve the roaming.
View 3 Replies View Related2008r2 Roaming Profile Back To Local
Feb 8, 2012After completing an AD upgrade to 2008r2 I've had my fill of roaming profiles. I want to change all users back so that their profile is on their pc. Of course ideally I'd like this to occur with the user affected as little as possible. Most users are still winxp but some win7 machines too.
View 18 Replies View RelatedCisco :: 5508 Wireless Roaming Config
Apr 7, 2011Currently have a 5508 in the lab and testing 4 AP's with it. Eventually there will be 18 AP's spread thru out different floor in our building.
So far access is working fine using WPA, 802.1x and the client configured to use windows logon credentials..But it doesn't seem to automatically transfer between access points.
Cisco Wireless :: 1242 - Roaming Between APs With No RADIUS
Feb 9, 2011I have 3 Cisco 1242 WAPs that I have deployed at a site that has NO RADIUS/AAA devices. I have given all of them a different channel (1,6,11), but the same SSID and crypto (WPA2-PSK). The issue is when a machine boots up it associates with the closest/strongest AP, but as the device "roams" it does not which to a different AP. It stays associated with the original AP until that signal is gone. Then it quickly associates with the closest AP with no problem.
How do I get the device to associate with the strongest WAP? I have research "fast roaming and WDS" but it seems like you need EAP/LEAP and they do NOT have that at all.
Dell :: Vostro 1500 - USB Adapter For Wi-Fi Roaming
Jan 13, 2012I have a Dell vostro 1500 and want to connect to a wireless network or WiFi roaming what is a recommended usb adapter?
View 1 Replies View Related