Cisco :: AP 1042 - DHCP Server Feature Supported To Work With Default BVI And Native VLAN
Jun 2, 2012
I was searching a lot , but I couldn't find any good example, how to configure DHCP server for our wireless clients on Cisco Autonomous AP. I'm looking for example how to configure Dot 11 radios and BVI interfaces.
I have no problem to configure DHCP server on BVI 1 and VLAN 1 ( native VLAN ) interfaces, but there is a problem with other BVI's and VLANs. Maybe this feature isn't supported? Maybe DHCP server feature is supported to work just with default BVI and native VLAN?
View 4 Replies
ADVERTISEMENT
Jun 22, 2011
So just recently my Internet has been running a lot slower than normal at different times of the day (completely random, could be fine for hours then just turns slow). I know it's not the Internet itself, since it's only happening on my computer, and none others in the house - and I'm far from capped. I've run AVG, Spybot & Malwarebytes' scans and have found no infections of any kind. I've run TCP Optimizer and used the "reset to windows default settings" feature, which also hasn't worked one bit. I've tried different Ethernet cables and different plugs in the modem and no improvement.
View 8 Replies
View Related
Apr 25, 2013
I got a new 1042 AP and connected it to the network. I have a 2504 contrller with 6 AP's already on it. I thought I could just plu in the new AP and it would show up in the AP group. Instead it shows up as a rouge AP. How do i get the new AP to show up in the default group?
View 24 Replies
View Related
Sep 9, 2011
My problem with ASR 1006 as i tried to use the feature IRB ( integrated routing and bridging ) but i find that this feature is not supported i assume it may be a problem with IOS version or may be i made he configuration not in the proper way
so i am asking to try this feature on ASR 1000 series and work with it as I test this feature on other routers and it work just fine.
View 1 Replies
View Related
Sep 20, 2012
My network topology is as follows:
Internet <-> Residential Gateway (RG) from ISP (OEM: Pace) [192.168.1.254/255.255.255.0] <-> RV180 [192.168.1.253/255.255.255.0] <-> SG500 switch [192.168.1.250/255.255.255.0] <-> rest of network.
I know this is a cascading LAN-to-LAN arrangement. The cable from the RG to the RV180 is from a LAN port on the RG to a LAN (not WAN) port on the RV180.
I eventually want to segment my network into a few VLANs from the RV180 down. I am aware most people would recommend DHCP on the "primary" router, but the RG is non-VLAN aware, so I figure I need to handle the DHCP off the RV180. At the same time, I have also opted not to do a LAN-to-WAN cascade because I want to retain the ability to configure the RG from the rest of the network and not have to cart a computer over to the RG to do it.
On the RG, I've disabled DHCP, and placed 192.168.1.253 in the DMZ.
On the RV180, I've enabled DHCP and put it in Router mode.
The issue is that I do not have any Internet connectivity. If I allow the computers in the network to receive IP addresses over DHCP, the default gateway that is communicated is 192.168.1.253, which is the RV180. If I configure static IPv4 information on my computers to point to 192.168.1.254, I am able to connect outside, as you would expect.
How can I get the RV180 to pass out DHCP IP addresses, but point to 192.168.1.254 as the default gateway? I thought the solution might be to create a default route (or something). I went to the static routes tab but it wouldn't let me enter 0.0.0.0 as a destination IP to route through 192.168.1.254.
Further down the line, is it possible for both the RG and the RV180 to connect directly to the SG500, along with the other nodes in my network? That way the RV180 only serves to maintain the VLANs and pass out IP addresses via DHCP, instead of having it be the choke through which everything goes through on the way out?
View 1 Replies
View Related
Dec 12, 2012
I have a Windows 7 64 bit computer that is connected to the internet through an ethernet cable to a 2-wire modem. Other computers at my home are connected wirelessly but I am not. I do have a NetGear print server and connect wirelessly with it to a printer. I am suddenly getting the notification "Native WiFi Default Profile Connected" even though I have been running the computer for a year without ever seeing this.
Is the wireless USB connection over-riding my ethernet connection? and is it possible to revert to having the ethernet connection be dominant? I prefer the ethernet connection for speed.
View 7 Replies
View Related
Oct 3, 2012
I have a RV042 router. The problem that I am having with it is that the DHCP is giving out the wrong Default Gateway and DNS Server. There is no option to change the DHCP server IP on any of the settings pages on the router. I am begining to think that there might not be a way to do it. I see that there is an option for the DNS under the DHCP page but the Public IP that is being handed out is not the one on that page. I also have 2 WAN connections hooked up as well a DSL link and a Cable link (the cable link is the primary one).
The following information is provided in an effort to resolve this issue:
IP of Router 10.0.0.2
IP of DHCP Server (the one that is being handed out):10.0.0.1
IP of DNS (the one that is being handed out): 10.0.0.11
What I want to it be.
IP of Router: 10.0.0.2
IP of DHCP 10.0.0.2
IP of DNS 10.0.0.2
View 3 Replies
View Related
Jan 5, 2013
what NATIVE VLAN is . What are the benifits of using this and when do we use this.
View 1 Replies
View Related
Dec 19, 2012
i want to know of the IOS verstion of cisco switch which support STP,some one told me that this feature is activated by deafalut if it not activated,how to turn on this Feature.i am using cisco 2960 Switch.
View 2 Replies
View Related
Nov 30, 2011
Is the feature "event logging" that is present on ACS 4.2 with the option to "send all events to the windows event log" no longer supported in ACS 5.2?
View 1 Replies
View Related
Jun 21, 2011
What is supported in terms of running a mixed feature set in a Cisco 3750 switch stack.We are looking at setting up a stack consisting of 5 x 3750V2 and 2 x 3750G. Due to a requirement for full EIGRP we need the IP Services feature set. Is it a supported configuration to run with 2 or 3 switches running the IP Services feature set as stack masters and the others running IP Base? I understand that if stack master priorities were set these switches with the higher feature set could manage the stack and offer IP Services accross the stack. If we were to lose all of the switches running IP Services the stack would drop back to IP Base.I am looking for guidance as to if this is a supported configuration and not in breach of licensing? Is this likely to cause any problem other than above now and for future IOS releases?
View 2 Replies
View Related
Jan 27, 2013
We have purchased two new Nexus 3548 switches. According to documenation the Nexus 3K does support vPC. When trying to enable the feature I get this:
nexus(config)# feature vpc
Error: vPC feature is not supported
nexus(config)#
We are running software version version 5.0(3)A1(1) and it looks like the latest version is 5.0(3)A1(2) so that's not much of a difference.Am I missing something here?
View 4 Replies
View Related
Aug 1, 2011
I have the following problem in LMS 4.0. I see a lot of CDP syslog messages about Native Vlan Mismatch, but the LMS doesn't report it in the disrepancy report. Why?? The similar problem is with TRUNK VLAN Mismatch. The customer doesn't use VTP in his network. All switches are in the VTP transparent mode.
View 1 Replies
View Related
Oct 29, 2011
I make qos on VPN Tunnel, but i make command service-policy output name, it show the error below Traffic Shaping feature is not supported in user defined class of parent level policy.My cisco router 1921, IOS : c1900-universalk9-mz.SPA.150-1.M5.bin
View 1 Replies
View Related
Apr 2, 2013
I have a 2811 Router (config below) with VPN configured. I can connect through the VPN and access devices on the native VLAN but I can't access the 10.77.5.0 (VLAN 5) network (I don't care to access the 10.77.10.0 - VLAN 10 network). This issue has been plagueing me for quite a while. I believe it's a NAT or ACL issue. VPN client IP pool is 192.168.77.1 - 192.168.77.10. [code]
View 4 Replies
View Related
Feb 19, 2013
In our network environment, we have a 2960 switch sitting behind our router. Off of this we have a lot of external connections, like our external DNS, firewall, and VPN concentrators. I've configured a VLAN other than the default, moved everything into it and then shut VLAN 1. In this hardening guide it says that your native VLAN should be something other than the user VLAN, but if I am not using any trunk links, wouldn't I not really have a native VLAN? I attempted to make the link to our firewall a trunk link and then set the native VLAN to something else.
View 5 Replies
View Related
Sep 16, 2011
Is PVID the same thing as "native vlan"? Can the native VLAN be changed on a SA520? Currently I believe it to be 1, I'd like to change the native VLAN to 10.
I have a scenario where I have a prexisting production LAN of 192.168.1.0/24 . It's a small organization (a church), but they purchased 3 Aironet 1130ag units. They want to have a "private" WLAN that is part of 192.168.1.0/24 , and a guest WLAN of a different subnet (I chose 192.168.20.0/24) . The two should never meet. There will likely never be a guest computer connected via ethernet. Guest computers would always have to connect wirelessly.
I left VLAN 1 on the SA520 192.168.75.0/24 subnet as default.I created a VLAN 10 , 192.168.1.0/24 subnet, and I created a VLAN 20, 192.168.20.0/24 subnet.Ports 1-3 of the SA520 are members of VLAN 1, 10, and 20 (cannot remove membership of VLAN1, which is pretty annoying).
Both are secured by WPA, and when I connect, the proper DHCP subnet passes from the firewall through to the wireless client, for each respective SSID.Ultimately, I'd like the SBS 2003 server to handle DHCP for VLAN 10, and have the SA520 handle DHCP for VLAN 20, but i'll take what I can get.
The original production LAN is connected via an unmanged switch.I'd like to trunk the unmanaged switch to Port 4 on the SA520. However, since the PVID (native vlan?) of SA520 is 1, and I cannot make Port 4 on the SA520 ony a member of VLAN 10, then anything traffic coming from the unanaged switch will automatically be tagged with VLAN1, correct? Thus causing the already existing production network to start receiving DHCP from the firewall in the 192.168.75.0/24 range.
View 1 Replies
View Related
Jan 11, 2012
Just trying to figure out how LAP manage clients in a h-reap setup.Have a setup with native vlan on 144 (switch and AP) and ssid tagging in other vlan... Got this on switch:
Jan 12 10:31:43.121: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 0811.9695.9b04 on port FastEthernet0/42.
Jan 12 10:31:43.121: %PORT_SECURITY-2-PSECURE_VIOLATION_VLAN: Security violation on port FastEthernet0/42 due to MAC address 0811.9695.9b04 on VLAN 144
Jan 12 10:37:42.770: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 0811.9695.9b04 on port FastEthernet0/42.
Jan 12 10:37:42.770: %PORT_SECURITY-2-PSECURE_VIOLATION_VLAN: Security violation on port FastEthernet0/42 due to MAC address 0811.9695.9b04 on VLAN 144
Wonder why clients MAC is seen on native vlan (and ofcourse also on taged vlan) ...?
View 4 Replies
View Related
Jan 28, 2013
I am going to creat VLANs very 1st time therefore for test purpose I have following simple scnerio.I have created 2 VLANs , VLAN2 and VLAN3 on Cisco Catalyst 2960 series switch. Ports 1-12 is assigned to VLAN2 and Ports 13-24 are assiged to VLAN3. Now I have configured DHCP on Microsoft Server 2003 defining 2 scopes with following configurations.
Scope 1 for VLAN 2--- Range is 172.16.0.17 to 172.16.0.30 with subnet mask=255.255.255.240 . Server IP address 172.16.0.17
( Note: Address 172.16.0.17 is excluded from dhcp server Scope 1 and give to the MS server itself)
Scope 2 for VLAN 3----Range is 172.16.0.33 to 172.16.0.46 with subnet mask=255.255.255.240 .
Now in Cisco 2960 series switches, under Vlan 2 and Vlan 3, I have following configurations...
interface Vlan2
ip address 172.16.0.30 255.255.255.240
ip helper-address 172.16.0.17
interface Vlan3
ip address 172.16.0.46 255.255.255.240
ip helper-address 172.16.0.17
Now the problem is when i connect a client computer to any port from 1-12, It gets correct IP address from Scope 1 but when I connect a computer to any port from 13-24, it does not get the ip address.
Further I want to do inter VLAN comunication as well for that purpose i Have an ISR 2900 series router. What further configuration i will have to do on router for inter vlan communication.
View 3 Replies
View Related
Feb 11, 2012
With out using any server, will DHCP be configured in cisco 2950/2960 switch?I man cisco it self should work as a dhcp server also.
View 10 Replies
View Related
May 25, 2012
1 week ago, I got a call from a client that reported a network outage, the client told me that, 3 switch has crashed he try to console but it just hang. I ask him, did you change something? he said he didn't change anything, he just pluged a nortelswitch to the cisco switch number 9, but that switch doesn't crash like the others (3,4,8). I check the uptime, and yes the switch never been powered off..
the topology look like this
____ 6500 ____
/ / |
1 2 3 4 5 ...... 9
the vlan is end to end vlan, so vlan span between all those switches. transparant. this is collapsed topology, core and distribution is the 6500 itself all of the 1-9 access switch are in the same rack, with no loopguard, and bpdu guard configured. and connected to the core using etherchannel. the problem is there is no log available to start the troubleshooting/investigation.
View 3 Replies
View Related
Jun 15, 2013
SG-300 52 native VLAN blocking network packets
View 3 Replies
View Related
Dec 22, 2012
I am having trouble after creating a management vlan (99) on a 3550 switch.I have configured the vlan (99) and given it an IP (192.168.1.100) and a default gateway (my router address - 192.168.1.99).I can ping to the switch from a PC and vice versa. The management VLAN IP is fine but now I cannot ping to the router from either the PC or the switch.It seems that just by adding VLAN 99 with it's own IP address has now prevented pings from the switch/ PC to the router ?Due to the fact that I have created a new switch management VLAN with an IP, does this mean I have set up the router as a 'router on a stick' scenario ? [code]
View 4 Replies
View Related
Jan 4, 2012
We are trying to setup a new configuration with 2960S as access switchs and a 4507 as a core switch.I want to protect the management IP VLAN of the swich using vrf on the 4507 so we :
SHUT VLAN 1 on every switch (2960 + 4507)
CREATE A NEW VLAN 289 (management vlan) -> IP network : 10.32.126.192/26
L3 VLAN on every switch
VLAN 289 in the VRF XXX on the 4507
create tunk between the switch and the 4507 :
switch mode trunk allowed vlan 200-230
sw trunk native vlan 289
so with this configuration on the 2960 the vlan 289 is UP/DOWN and UP/UP on the 4507 I can access to the 4507 using the IP in the VLAN 289 but i cannot access to the 2960 behind the 4507 CDP connectivity is ok?
View 14 Replies
View Related
Oct 7, 2012
I am migrating an existing LAN from 3550 to 3750X-12S. In the existing configuation, I´ve got some trunks with native VLAN <> 1. The native VLAN is also used for user data transport. With IOS 15.0(1)SE3 on 3750X I recognized, that per default behavior PVST is not active for a VLAN defined as native, even if the corresponding trunk is up and trunking. My current workaround is to add a "switchport access vlan" command on the trunk even this one never should become an access port. With this statement only the switch is activating the PVST for the native VLAN. For all other vlans PVST works as exspected. [code]
View 6 Replies
View Related
Mar 5, 2012
On my new E4200v2, after I tried to move beyond the disappointment of Cisco removing Internet Access Policy entirely, I decided to give the stripped down Parental Controls a try.
Sadly, I didn't have any luck doing what I needed to do... block my Tivo's from accessing Youtube.
I enabled Parental Controls, Added the Target Devices (my Tivo's did show up), and added "Youtube.com" as blocked site #1. Saved. Entered the parental password when prompted. Even rebooted the router.
But Youtube wasn't blocked. So I added to the target list a non-Tivo device (a Macbook) for a reality check, and rebooted the router again... still no luck. Youtube still not blocked.
So then I started to wonder if their Parental Control depends somehow on the local DHCP server & Client list. Because my E4200 has DHCP Server = OFF (I have always used a Windows Server for DHCP).
I tried to call Linksys support to get this working, but after 45 mins, including escalation to senior engineer, they really were pretty useless (no real familiariarity with my problem) then they disconnected my call!
View 7 Replies
View Related
Jun 6, 2012
I have several closets with Cisco 3560 on the edge that I'd like to change the vlan that's used for the management vlan on each. In the core I have a Cisco 6509 with Sup720's.
I'd like to do this by changing the native vlan on the trunk port on the core 6509 interface that connects to the 3560. and leave the management vlan on the 3560 as vlan 1.
Seems trivial but what I tried didn't work and I didn't have the window to troubleshoot. I'll paste the simplified configs for the interfaces below
!
6509 configs:
!
interface Vlan50ip address 172.16.50.2 255.255.255.0!interface FastEthernet
[Code]....
View 5 Replies
View Related
Dec 13, 2012
We have a problem with CDP packets on sent by our Cisco 6509's. Unlike our other Cisco switches (4948G, 5020, etc.), the 6509 tags administrative traffic on the native vlan. As a result the CDP packets are sent with an 802.1Q header with a tag of 1. The other switches send the CDP packets untagged on the native vlan. This causes problems because we have non-Cisco devices in our lab that also receive and send CDP, but they do not process the packets that are tagged by the 6509. They see the packets from the 4948 and 5020 just fine.
How can I disable the administrative native vlan tagging on the 6509? Here is the current setup:
nwkdev-6509-1#show vlan dot1q tag native
dot1q native vlan tagging is disabled globally
nwkdev-6509-1#show interfaces gigabitEthernet 1/9/1 switchport
[Code].....
View 13 Replies
View Related
Jan 22, 2013
I have just configured up a sg500 with a lacp trunk to an upstream switch.
I am getting native vlan mismatch on the individual ports of the lacp team.
24-Jan-2013 12:54:48 %CDP-W-NATIVE_VLAN_MISMATCH: Native VLAN mismatch detected on interface gi1/1/24.
24-Jan-2013 12:57:35 %CDP-W-NATIVE_VLAN_MISMATCH: Native VLAN mismatch detected on interface gi1/1/48.
[Code].....
View 1 Replies
View Related
Jan 14, 2013
I've been experimenting with the 'vlan dot1q tag native' command on a switch and it seems as though tagging the native vlan breaks vty access to my access point.With the 'vlan dot1q tag native' commnand applied, I lose management connectivity to the AP with 'no vlan dot1q tag native' applied, connectivity is restored. Why is this? Is it safe to say that one can access the AP via vty lines using ONLY untagged packets?
SWITCH
Model: WS-C3560G-24PS
Code: c3560-advipservicesk9-mz.122-46.SE
--Abbreviated CONF
vlan dot1q tag native
[code]....
View 14 Replies
View Related
Jan 23, 2013
I've been given the task to clean-up our network config, and have walked into a disaster zone.We have a 4510R on site with everyone using the default VLAN, VLAN 1.I have created 4 new VLANS, VLAN100, VLAN150, VLAN200, VLAN250 I have assigned interface addresses to each VLAN and configured Inter VLAN routing.I can route to and from each new vlan with no problem, i.e VLAN250>VLAN100 VlAN100>VLAN200 etc but I can't route to VLAN 1(Default VLAN) from any of them, I can ping the interface on VLAN 1 from any VLAN , but any hosts are unreachable. On the flip side , from VLAN 1 I can route to all of the VLANS.
View 3 Replies
View Related
Mar 14, 2012
How do I find the default throughput supported by the Router 3925E?I need a router that supports 400Mbps line 3900.The 3925E supports? If so, you need to upgrade or add a EHWIC? If so, what can I addto support that throughput?
View 6 Replies
View Related
Jan 8, 2013
We implemented WLC 5508 software version 7.3, with 8 Aironet devices, most of them are AIR-LAP1131AG-E-K9, and two AIR-LAP1242AG-E-K9.I could really have benefits of VLAN select feature, but I noticed that it's not working like it should. Two interfaces are in Interface group, but from 45 clients only few of them has IP address from one subnet, others have from second sub.I see requirements for this to work is 32 MB of flash on LWAP devices..I only have 16 MB.. upgrade of flash on devices or something ?
View 12 Replies
View Related
