Is the feature "event logging" that is present on ACS 4.2 with the option to "send all events to the windows event log" no longer supported in ACS 5.2?
View 1 Repliesi can't configure "logging event spanning-tree" on a specific port under IOS 12.2.(58) SE2 (all other "logging events" are possible), under 12.2 (55) it is possible. Is it now a known bug or a default value?
View 4 Replies View RelatedWhy the IOS on 4500 doesn't support globally, although am running the IOS 12.2,need for logging event link-status global.
View 3 Replies View RelatedMy problem with ASR 1006 as i tried to use the feature IRB ( integrated routing and bridging ) but i find that this feature is not supported i assume it may be a problem with IOS version or may be i made he configuration not in the proper way
so i am asking to try this feature on ASR 1000 series and work with it as I test this feature on other routers and it work just fine.
i want to know of the IOS verstion of cisco switch which support STP,some one told me that this feature is activated by deafalut if it not activated,how to turn on this Feature.i am using cisco 2960 Switch.
View 2 Replies View RelatedWhat is supported in terms of running a mixed feature set in a Cisco 3750 switch stack.We are looking at setting up a stack consisting of 5 x 3750V2 and 2 x 3750G. Due to a requirement for full EIGRP we need the IP Services feature set. Is it a supported configuration to run with 2 or 3 switches running the IP Services feature set as stack masters and the others running IP Base? I understand that if stack master priorities were set these switches with the higher feature set could manage the stack and offer IP Services accross the stack. If we were to lose all of the switches running IP Services the stack would drop back to IP Base.I am looking for guidance as to if this is a supported configuration and not in breach of licensing? Is this likely to cause any problem other than above now and for future IOS releases?
View 2 Replies View RelatedWe have purchased two new Nexus 3548 switches. According to documenation the Nexus 3K does support vPC. When trying to enable the feature I get this:
nexus(config)# feature vpc
Error: vPC feature is not supported
nexus(config)#
We are running software version version 5.0(3)A1(1) and it looks like the latest version is 5.0(3)A1(2) so that's not much of a difference.Am I missing something here?
I make qos on VPN Tunnel, but i make command service-policy output name, it show the error below Traffic Shaping feature is not supported in user defined class of parent level policy.My cisco router 1921, IOS : c1900-universalk9-mz.SPA.150-1.M5.bin
View 1 Replies View RelatedI was searching a lot , but I couldn't find any good example, how to configure DHCP server for our wireless clients on Cisco Autonomous AP. I'm looking for example how to configure Dot 11 radios and BVI interfaces.
I have no problem to configure DHCP server on BVI 1 and VLAN 1 ( native VLAN ) interfaces, but there is a problem with other BVI's and VLANs. Maybe this feature isn't supported? Maybe DHCP server feature is supported to work just with default BVI and native VLAN?
when the supplicant is missing vlan500 is open for port and everything is ok, but when supplicant has wrong configuration something happend and port is always authenticating(every 30s, vlan500 is not assign to this port with bad configuration supplicant) and logs show something like that
Jul 10 10:20:12.362: %AUTHMGR-5-START: Starting 'dot1x' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A3545161E4 Jul 10 10:20:44.365: %AUTHMGR-5-START: Starting 'mab' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A45451DF11 Jul 10 10:20:44.399: %MAB-5-FAIL: Authentication failed for client (001e.3718.7297) on Interface Ga0/1AuditSessionID 0A0EFF5B000004A45451DF11 Jul 10 10:20:44.399: %AUTHMGR-7-RESULT: Authentication result 'no-response' from 'mab' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A45451DF11 Jul 10 10:20:44.399: %AUTHMGR-7-FAILOVER: Failing over from 'mab' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A45451DF11 Jul 10 10:20:44.399: %AUTHMGR-5-START: Starting 'dot1x' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A45451DF11
version - Cisco IOS Software, C3560E Software (C3560E-UNIVERSALK9-M), Version 15.0(1)SE2
port config:
interface GigabitEthernet0/1
switchport access vlan 104
switchport mode access
switchport voice vlan 200
authentication event fail action authorize vlan 500
[code]....
The WAG160N V1 you can change the dns primary default router for the connection "alice adsl 7 mega"? I would like to change it because in widows8, I keep giving every time the system event log, the error: "The computer was not assigned an address from the network (from the DHCP Server) for the Network Card with network address 0xF07D686CB987 . has encountered the following error: 0x79. Your computer will continue to make further attempts to obtain an address " I checked with the ping and the first two dns 85.37.17.15 does not work, while the second works 85.38.28.74. how to configure the DWA140N rev.B2 the property is currently configured as follows: IEEE802.11h = Disable Multimedia / Gaming Environment = Disable Country / region (2.4 GHz) = n. 0 (1-11) Country / region (5 GHz) = n. 0 (36-64, 149-165) Radio on / off = Active Selective Suspend = Disable Selective Suspend idle timeuot in senond = 5 Sensitivity roaming = Disable (options, max, min, average) Ad hoc support 802.11n = Disable
View 3 Replies View RelatedI have an ACS 5.2 VM that went down during an ESX host issue. Since it has no VMWare tools, it didn't migrate to another host very nicely. When the box came up, I had to delete the Virtual nic and re-add it and then set up the IP info again to get the VM communicating on the network.Currently the ACS box is not logging anything. There are no logs visable. What can I do to check why there are no logs visable? Authentication is working because wireless uses are still getting on the wireless network, but there are no logs that show passed or failed attempts.
View 4 Replies View RelatedI have 3 ACS 5.2 servers both here and in the US. On friday night, our building lost power and it came back up early saturday morning. During this, the Wireless controllers dropped their configs and reverted back to point to the old ACS servers again. After fixing this, all wireless works now in my location. But, ACS is not logging my sessions even though i can connect to wireless with phone or laptop. It should log the authentication process if the server is here or in the US, but it is only logging for the other 2 servers. now on a weird note, the VPN for users in this location is authenticationg just fine.
View 2 Replies View RelatedI am looking for the way how to disagle logging of one user. We are using one testing user for checking accesibility of ACS from large number of switches - this checking exhausting logs quite quickly. Is it possible to disable logging of such user?
View 2 Replies View RelatedI am using an ACS 4.2 trial version, and am trying to enable the password aging feature. I am using the ACS internal database for users. I have looked at the user guide, which has clear instructions, but I don't seem to have the ability to set password aging rules. When I go into the Jump To pull down, I am only presented with four options; Access Restrictions, Enable Options, IP Address Assignment and TACACS+. The Password Aging options are not shown.
View 1 Replies View RelatedI am sending TACACS administration logging to a syslog server. When the messages show up on the syslog server, they are 5 hours ahead of the actual time. Time on the ACS is correct - local logging shows the correct time. Time on the syslog server is correct...all other devices/systems sending syslog messages to it are coming through with the correct time. why the ACS syslog messages would be 5 hours ahead?
View 3 Replies View RelatedI have ACS 1120 ACS appliance running ACS version 5.2.0.26.5 ,authenticating VPN users connecting from internet using radius protocol , we have requirement that VPN user account should be disabled by a specific date , Means user ID should be revoked when their contract expire connecting to our data center .
I know this feature is available on ACS version 4.2.,but i could not this feature set on ACS 5.2.0 when user account is created , whether any new sepicfic patch has this feature enabled after acs version 5.2.0.26.5.
With out this feature this set , i cannot ensure ID are revoked automatically ,when specific date come in to end user.
The table referenced in the new 1.1 ISE guide show 12.2(33)SXI6 is the minimum version for support. Does this mean this version or above? Does ISE is tested in newer SXJ streams? We have a massive rollout of SUP720s to do and need to know the most stable version to load in preparation for ISE.
View 1 Replies View RelatedI'm encountering what I think is an issue on logging system on FW ASA 5520 - Asa Version 8.4(2), ASDM version 6.4(5). When I disabled the logging inside a rule from ASDM, or from console with the "log disable" option inside ACL, If I check in ASDM logging real time window I continue to see all the entry related to disabled rules. This is a correct behaviour about ASA logging ? How I can "hide" the entry related to disabled rules (this is what I need for troubleshooting purposes) ?
View 1 Replies View Relatedwhat is the maximum number of AAA clients supported by a single ACS5.3 instance?
View 1 Replies View RelatedSo just recently my Internet has been running a lot slower than normal at different times of the day (completely random, could be fine for hours then just turns slow). I know it's not the Internet itself, since it's only happening on my computer, and none others in the house - and I'm far from capped. I've run AVG, Spybot & Malwarebytes' scans and have found no infections of any kind. I've run TCP Optimizer and used the "reset to windows default settings" feature, which also hasn't worked one bit. I've tried different Ethernet cables and different plugs in the modem and no improvement.
View 8 Replies View RelatedIf it is, can you point me to the correct drivers page as I cannot find it.
View 1 Replies View Relatedwhy Windows Server 2008 is not a supported OS for Cisco Network Assistant?I am currently evaluating switch management solutions for use with Catalyst 2960 and 3750 series switches, and would like to be able to backup and restore configurations, as well as make configuration changes. My management Server is running Server 2008.Is Prime LMS my only option?
View 5 Replies View RelatedI planned to install a LMS 4.0.1 on a VMWare server with Windows 2008 R2 64bits.
Is it supported with the "Windows 2008 R2" patch or do I need to order LMS 4.1 version ?
The WCS haven't have new event since the count of event goes 40000.And, the wcs-3-0.log shows INFO[stspoll] Event Queue seems full.In the FAQ which says:#The WCS keeps the last 40,000 events in the system and clears them up after seven days. An event or alarm can have 1000 bytes on average.shouldn't it clears them up after seven days? how to clean events by manual?
View 0 Replies View Relatedwhy getting temperature event in 3560 switch, and we checked the Network room Temp it's normal around (22).
View 8 Replies View RelatedIn 12.4(24)T4, I don't seem to have the SNMP detector in Advanced Security; however, it is present in Advanced IP Services.Is this a known pre-requisite? I can't seem to find any documentation or guidance from Feature Navigator that this should be the case.
Adv Sec (3845):
(config-applet)#event ?
application Application specific event
cli CLI event
config Configuration policy event
counter Counter event
[code]....
I have a server that is running on 2003 and we are having a few problems and in the event log I am getting id101 with the message whats virtual is not enable and i am not sure what this refers to or how to sort it out.
View 2 Replies View RelatedIs it possible to get the result in th event list in the form of graph, ie. like delay,throughput in the form of graph
View 3 Replies View RelatedCan LMS 4.0 display event directly on Topology Services when error occurs without accessing the other module by clicking right mouse on device? Anyway, I configured the logging command on all device but I cant see any syslogs on Event Monitor > Syslog. It dislays "No Syslogs are available" message.
View 1 Replies View RelatedI want to use an EEM applet on a Cisco IOS 2431 voice gateway running 15.1(2)T to take action upon expiration of a SIP registration (with its sip registrar). I thought that it might be possible to use existing error messages generated by the ios sip application to trigger an EEM applet.Is there a reference that lists all SYSLOG messages that SIP can generates, and their error levels? Can you show me how to turn on syslog messages, so that I can cause a SIP registration expiration on my GW and then see what SYSLOG messages are produced?
I think I understand how to write an applet and its event trigger from a SYSLOG message pattern, but I am having trouble seeing any SIP error messages at all, except if I turn on Debug, which usually produces way too many messages and may impact performance.
how to take the event log of Cisco switch 3560, its argent.
View 1 Replies View RelatedThe client is only interested to have one-WAN(MPLS) and One internet circuit with Dual ASA5510 primary/failover configuration. In the event primary firewall fails, there is no direct WAN/internet connection to failover firewall. I beleived that to mitigate the issue, I needed to add a layer 3 switch , and have each circuit (MPLS/Internet) or (modems/routers) connect to a L3 switch. L3 switch will do the vlan based routing based on the state of firewall. ? am i correct? The client want automatic failover to secondary firewall in the event the actual firewall failed without impacting the day to day business.
View 3 Replies View Related