Cisco :: 3845 / EEM / SNMP Event Detector Not Available
Dec 16, 2011
In 12.4(24)T4, I don't seem to have the SNMP detector in Advanced Security; however, it is present in Advanced IP Services.Is this a known pre-requisite? I can't seem to find any documentation or guidance from Feature Navigator that this should be the case.
Adv Sec (3845):
(config-applet)#event ?
application Application specific event
cli CLI event
config Configuration policy event
counter Counter event
[code]....
View 2 Replies
ADVERTISEMENT
Sep 10, 2012
I have a problem with SNMP. I using Cisco 3845 in distribution layer. >600 subinterfaces. When my managment system send response - the cpu Utilization on cisco3845 near 100%. I want to prohibited my Cisco answer on response about interface status.
View 2 Replies
View Related
Jan 2, 2013
I'm attempting to set up a detector that fires when an application is seen. I've set up the flow monitor
2951-HQ#sho flow monitor AppWatch cache
Cache type: Normal
Cache size: 4096
[code]....
I'm runnig c2951-universalk9-mz.SPA.152-3.T2.bin
View 3 Replies
View Related
Mar 9, 2009
If you deploy a Cisco 1242 a/b/g access point as a rogue detector, can this be used for 802.11n wired detection as well.i.e Will the controller send the MAC addresses of the 802.11n clients and APs. url...
View 8 Replies
View Related
Dec 14, 2012
I'm using a 2504 controller. I dont have WCS.My questions are about the best way to configure a Rogue Detector AP.
In my lab environment I setup the WLC with 2 APs. One AP was in local mode, and I put the other in Rogue Detector mode.The Rogue Detector AP was connected to a trunk port on my switch. But the AP needed to get its IP address from the DHCP server running on the WLC. So I set the native vlan of the trunk port to be the vlan on which the WLC management interface resides. If the trunk port was not configured with a native vlan, the AP couldn't get an address through DHCP, nor could the AP communicate with the WLC. This makes sense because untagged traffic on the trunk port will be delivered to the native vlan. So I take it that the AP doesn't know how to tag frames.Everything looked like it was working ok.
So I connected an autonomous AP (to be used as the rogue), and associated a wireless client to it. Sure enough it showed up on the WLC as a rogue AP, but it didn't say that it was connected on the wire. From the rogue client I was able to successfully ping the management interface of the WLC.
But the WLC never actually reported the rogue AP as being connected to the wired network.So my questions are:
1. What is the correct configuration for the trunk port? Should it not be configured with a native vlan? If not, then I'm assuming the rogue detector AP will have to have a static IP address defined, and it would have to be told which vlan it's supposed to use to communicate with the WLC.
2. Assuming there is a rogue client associated with the rogue AP, how long should it reasonably take before it is determined that the rogue AP is connected to the wired network? I know this depends on if the rogue client is actually generating traffic, but in my lab environment I had the rogue client pinging the management interface of the WLC and still wasn't being picked up as an on-the-wire rogue.
View 4 Replies
View Related
May 28, 2012
(5508 WLC, 1142N APs).I understand if I enable the AP mode to Rogue Detector from the details page of the AP, the AP stops accepting requests and is now looking for rogue items on the wired network. Is this the same when I enable Rogue Location Discovery Protocol? Will I lose the wireless functionality of all of my APs on the controller?
Next question, when I look at the Rogue Summary on the Monitoring page I see three Adhoc Rogue devices. When I select the Detail link only one shows. I remember the other two were HP mutifuction devices with WIFI enabled but I cannot retrieve that information anymore.
View 9 Replies
View Related
Dec 10, 2012
Is there any physical or technical diferrences between PWR-3845 AC/2 and PWR-3845 AC? We are trying to order replacement parts and wondering if PWR-3845 AC is for one power supply and AC/2 means you get two with one order?
View 1 Replies
View Related
Dec 7, 2012
Is there any physical or technical diferrences between PWR-3845 AC/2 and PWR-3845 AC? We are trying to order replacement parts and if PWR-3845 AC is for one power supply and AC/2 means you get two with one order.
View 1 Replies
View Related
Jul 21, 2011
I am testing rogue on wire using 5508 WLC and , I have a dedicated AP configured as rogue detector and configured the switch port where the Rogue detector is connected as trunk. I have plugged in an autonomous AP with open authentication to the same switch so that it can act as a rogue. On the WLC, I can see that Autonomous AP as rogue on Wire. But along with that I am seeing another AP as rogue on wire, even though i have plugged in only one Autonomous AP to the switch.
View 3 Replies
View Related
Nov 8, 2011
The WCS haven't have new event since the count of event goes 40000.And, the wcs-3-0.log shows INFO[stspoll] Event Queue seems full.In the FAQ which says:#The WCS keeps the last 40,000 events in the system and clears them up after seven days. An event or alarm can have 1000 bytes on average.shouldn't it clears them up after seven days? how to clean events by manual?
View 0 Replies
View Related
Mar 9, 2013
why getting temperature event in 3560 switch, and we checked the Network room Temp it's normal around (22).
View 8 Replies
View Related
May 25, 2011
I have a server that is running on 2003 and we are having a few problems and in the event log I am getting id101 with the message whats virtual is not enable and i am not sure what this refers to or how to sort it out.
View 2 Replies
View Related
Dec 13, 2012
Is it possible to get the result in th event list in the form of graph, ie. like delay,throughput in the form of graph
View 3 Replies
View Related
Oct 24, 2011
Can LMS 4.0 display event directly on Topology Services when error occurs without accessing the other module by clicking right mouse on device? Anyway, I configured the logging command on all device but I cant see any syslogs on Event Monitor > Syslog. It dislays "No Syslogs are available" message.
View 1 Replies
View Related
Jul 27, 2011
I want to use an EEM applet on a Cisco IOS 2431 voice gateway running 15.1(2)T to take action upon expiration of a SIP registration (with its sip registrar). I thought that it might be possible to use existing error messages generated by the ios sip application to trigger an EEM applet.Is there a reference that lists all SYSLOG messages that SIP can generates, and their error levels? Can you show me how to turn on syslog messages, so that I can cause a SIP registration expiration on my GW and then see what SYSLOG messages are produced?
I think I understand how to write an applet and its event trigger from a SYSLOG message pattern, but I am having trouble seeing any SIP error messages at all, except if I turn on Debug, which usually produces way too many messages and may impact performance.
View 1 Replies
View Related
Feb 26, 2012
how to take the event log of Cisco switch 3560, its argent.
View 1 Replies
View Related
Jun 6, 2011
The client is only interested to have one-WAN(MPLS) and One internet circuit with Dual ASA5510 primary/failover configuration. In the event primary firewall fails, there is no direct WAN/internet connection to failover firewall. I beleived that to mitigate the issue, I needed to add a layer 3 switch , and have each circuit (MPLS/Internet) or (modems/routers) connect to a L3 switch. L3 switch will do the vlan based routing based on the state of firewall. ? am i correct? The client want automatic failover to secondary firewall in the event the actual firewall failed without impacting the day to day business.
View 3 Replies
View Related
Apr 4, 2013
I'm trying to enforce a triggered EEM applet with an ACL rule. Is this even possible? I've been searching for weeks, but the closest thing I can find is using an SNMP evenst, which isn't what I'm looking for. I've looked at the list of event triggers (and I've used resource events before), but I can't find anything that works.
I'm specifically trying to switch packet capture on/off (with a script or EEM applet) on some 2900 series routers. I have 2960s and 2911s.
View 3 Replies
View Related
Sep 14, 2011
I've been getting warning messages from the event log of a 1300 series bridge, which is set as an Access Point in the network, states: 'Packet to client (mac address) reached max retries, removing the client'; I'm not sure why the client is removed. Does 'reached max retries' mean that the client has tried to many times to connect to the AP/Bridge?
View 1 Replies
View Related
Nov 30, 2011
Is the feature "event logging" that is present on ACS 4.2 with the option to "send all events to the windows event log" no longer supported in ACS 5.2?
View 1 Replies
View Related
May 8, 2012
Is it possible to automatically shutdown the OUTSIDE interface on a Cisco ASA 5520 in case of intrusion?.
In my opinion if there is an attempt of intrusion, just the device would stop it. If it cannot detect it, how can the device recognize the event and so shutdown the interface?. Am I correct?
View 1 Replies
View Related
Oct 20, 2011
i can't configure "logging event spanning-tree" on a specific port under IOS 12.2.(58) SE2 (all other "logging events" are possible), under 12.2 (55) it is possible. Is it now a known bug or a default value?
View 4 Replies
View Related
Jul 25, 2011
High Utilization event generated for Nexus 7010 shows in LMS 4.0.1. share your input why its generated. We have checked up Nexus, it showed not utilization.
View 2 Replies
View Related
Jul 12, 2012
I have EEM configured on cisco 3560 switch. The configuration is below. I want that switch inform me through email when device with particilular IP address become unavailable. I already try to debug this with debug event manager action mail but didn't see any output. [code]
View 2 Replies
View Related
Mar 17, 2013
Since we upgrade WLC in version 7.0.230 my PC with atheros card (version client 8.0.140 and driver 9.2.0.419) have brief interruption. In System events we have a lot of events ID 4201 and 1007. I try use Windows Wireless Client and we have not problem but the roaming is not fast. I don't find other client Utility for Atheros.
View 2 Replies
View Related
Feb 21, 2012
Why the IOS on 4500 doesn't support globally, although am running the IOS 12.2,need for logging event link-status global.
View 3 Replies
View Related
Aug 24, 2011
I have a (single) client (it is a cisco IOS router) behind a wireless workgroup bridge (cisco1242).The client's IP address is obtained via DHCP from the wired network.Now, when roaming occurs, the Client will never have knowledge about this event,and hence will not renew its IP address until lease expiers. This is not a problem of course when Layer 2 roam occurs, but with Layer 3
roam it will interrupt the traffic.
The cisco's IP Mobile implementation does have this issue addressed in DCCoA scenario: the WGB is configured to send an SNMP trap on its dotradio state change;the cisco mobile router is configured with snmp-server manager to process this trap and start DHCP renew on the Down/Up event. Unfortunately, this works in Mobile IP scenario only because I cannot make it work without the mobile router registered with a home agent.
how to force DHCP renew on a client (cisco IOS router) in such a situation - event scripting, SLA, or ...?
View 5 Replies
View Related
Jul 15, 2012
when the supplicant is missing vlan500 is open for port and everything is ok, but when supplicant has wrong configuration something happend and port is always authenticating(every 30s, vlan500 is not assign to this port with bad configuration supplicant) and logs show something like that
Jul 10 10:20:12.362: %AUTHMGR-5-START: Starting 'dot1x' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A3545161E4 Jul 10 10:20:44.365: %AUTHMGR-5-START: Starting 'mab' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A45451DF11 Jul 10 10:20:44.399: %MAB-5-FAIL: Authentication failed for client (001e.3718.7297) on Interface Ga0/1AuditSessionID 0A0EFF5B000004A45451DF11 Jul 10 10:20:44.399: %AUTHMGR-7-RESULT: Authentication result 'no-response' from 'mab' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A45451DF11 Jul 10 10:20:44.399: %AUTHMGR-7-FAILOVER: Failing over from 'mab' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A45451DF11 Jul 10 10:20:44.399: %AUTHMGR-5-START: Starting 'dot1x' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A45451DF11
version - Cisco IOS Software, C3560E Software (C3560E-UNIVERSALK9-M), Version 15.0(1)SE2
port config:
interface GigabitEthernet0/1
switchport access vlan 104
switchport mode access
switchport voice vlan 200
authentication event fail action authorize vlan 500
[code]....
View 3 Replies
View Related
Apr 18, 2013
A customer has a wireless PTP bridge using a pair of 1410 bridges. The non-root bridge event log shows the RSSI polling information message indicating the link's signal strength; ie. -42 dBm. It updates every few seconds or so. The root bridge does not show this information in the event log. Both bridges have the event log configuration options set identically, all messages types are enabled. I can't find any reference to this in the documents. Is this by design? I thought that maybe a root bridge if it was set up as a multi-point might be overwhelmed if it was showing/scrolling RSSI from multiple non-roots.
View 3 Replies
View Related
Nov 24, 2012
The WAG160N V1 you can change the dns primary default router for the connection "alice adsl 7 mega"? I would like to change it because in widows8, I keep giving every time the system event log, the error: "The computer was not assigned an address from the network (from the DHCP Server) for the Network Card with network address 0xF07D686CB987 . has encountered the following error: 0x79. Your computer will continue to make further attempts to obtain an address " I checked with the ping and the first two dns 85.37.17.15 does not work, while the second works 85.38.28.74. how to configure the DWA140N rev.B2 the property is currently configured as follows: IEEE802.11h = Disable Multimedia / Gaming Environment = Disable Country / region (2.4 GHz) = n. 0 (1-11) Country / region (5 GHz) = n. 0 (36-64, 149-165) Radio on / off = Active Selective Suspend = Disable Selective Suspend idle timeuot in senond = 5 Sensitivity roaming = Disable (options, max, min, average) Ad hoc support 802.11n = Disable
View 3 Replies
View Related
Mar 10, 2013
I have cisco 3845 on my network now its working fine.Now one of my client is asking to they want to connect their network through my router ethernet interface.
now my doubt is 3845 router will support two different gateways.
how can i route their network they have bring new router.
View 2 Replies
View Related
Mar 7, 2013
I have 2 x Cisco 3845 each one with a DS3 circuit, both running c3845-spservicesk9-mz.124-15.T3. In each of them I have one pvc provided by my carrier and I received the following info to configure:
vc-class atm ATM
vbr-nrt 44096 44096 1
oam-pvc manage
oam retry 3 10 1
encapsulation aal5mux ip
That worked fine for the first one with the NM-ATM-DS3, however, using NM-1A-T3/E3, it seems that I'm restricted up to 40700 kbps PCR/SCR:
router(config-vc-class)#vbr-nrt ?
I tried to look for some reference but couldn't find... Is there a way I can have a full DS3 with this card?
View 8 Replies
View Related
Jun 28, 2011
We have 3845 Router which is using for only Internet connectivity with one ISP(X) Customer has only one Vlan, Public AS number, and Public IP pool.Scenario:User--> L2Access-SW--> L3 (6500) SW--> Firewall (5520) --> IPS--> 3845Router.Now we have another ASR Router, which also has Internet connectivity from another ISP(Y).Now the issue is we would like to use both ISP in active/active scenario.
View 1 Replies
View Related
