The WCS haven't have new event since the count of event goes 40000.And, the wcs-3-0.log shows INFO[stspoll] Event Queue seems full.In the FAQ which says:#The WCS keeps the last 40,000 events in the system and clears them up after seven days. An event or alarm can have 1000 bytes on average.shouldn't it clears them up after seven days? how to clean events by manual?
View 0 Repliesi have issues logging into one of our core switches.its a 6509 switch but i cannot log in remotely.when i try to console in on the console port, i cannot log in instead i get the above error message.I haven't rebooted yet but would it solve the problem as this switch is a production switch.
View 6 Replies View RelatedI'm seeing the alert "CPU Receive Multicast Queue is full on Controller" on the WCS from one of my controllers. This is during peak hours and on a pretty busy WLC. I can't find any related lines in the logfiles. I'm currently running software version 7.0.220.0 on a WISMs.
View 13 Replies View RelatedI'm starting to see an error creep up that I havn't seen since 2003/2004 on my brand new 5508 controllers. I'm recieving the following from my WCS: Receive Multicast Queue is full on Controller and then on the controller itself RX Multicast Queue Full. I understand this used to be due to a large influx of ARP requests or CDP packets on older controllers but, this was supposed to be fixed in an update many years ago.
Has seen this on their 5508's. These were advertised as having the horsepower to handle our user loads which arn't really that high at 300 users at any given time max.
why getting temperature event in 3560 switch, and we checked the Network room Temp it's normal around (22).
View 8 Replies View RelatedIn 12.4(24)T4, I don't seem to have the SNMP detector in Advanced Security; however, it is present in Advanced IP Services.Is this a known pre-requisite? I can't seem to find any documentation or guidance from Feature Navigator that this should be the case.
Adv Sec (3845):
(config-applet)#event ?
application Application specific event
cli CLI event
config Configuration policy event
counter Counter event
[code]....
I have a server that is running on 2003 and we are having a few problems and in the event log I am getting id101 with the message whats virtual is not enable and i am not sure what this refers to or how to sort it out.
View 2 Replies View RelatedIs it possible to get the result in th event list in the form of graph, ie. like delay,throughput in the form of graph
View 3 Replies View RelatedCan LMS 4.0 display event directly on Topology Services when error occurs without accessing the other module by clicking right mouse on device? Anyway, I configured the logging command on all device but I cant see any syslogs on Event Monitor > Syslog. It dislays "No Syslogs are available" message.
View 1 Replies View RelatedI want to use an EEM applet on a Cisco IOS 2431 voice gateway running 15.1(2)T to take action upon expiration of a SIP registration (with its sip registrar). I thought that it might be possible to use existing error messages generated by the ios sip application to trigger an EEM applet.Is there a reference that lists all SYSLOG messages that SIP can generates, and their error levels? Can you show me how to turn on syslog messages, so that I can cause a SIP registration expiration on my GW and then see what SYSLOG messages are produced?
I think I understand how to write an applet and its event trigger from a SYSLOG message pattern, but I am having trouble seeing any SIP error messages at all, except if I turn on Debug, which usually produces way too many messages and may impact performance.
how to take the event log of Cisco switch 3560, its argent.
View 1 Replies View RelatedThe client is only interested to have one-WAN(MPLS) and One internet circuit with Dual ASA5510 primary/failover configuration. In the event primary firewall fails, there is no direct WAN/internet connection to failover firewall. I beleived that to mitigate the issue, I needed to add a layer 3 switch , and have each circuit (MPLS/Internet) or (modems/routers) connect to a L3 switch. L3 switch will do the vlan based routing based on the state of firewall. ? am i correct? The client want automatic failover to secondary firewall in the event the actual firewall failed without impacting the day to day business.
View 3 Replies View RelatedI'm trying to enforce a triggered EEM applet with an ACL rule. Is this even possible? I've been searching for weeks, but the closest thing I can find is using an SNMP evenst, which isn't what I'm looking for. I've looked at the list of event triggers (and I've used resource events before), but I can't find anything that works.
I'm specifically trying to switch packet capture on/off (with a script or EEM applet) on some 2900 series routers. I have 2960s and 2911s.
I've been getting warning messages from the event log of a 1300 series bridge, which is set as an Access Point in the network, states: 'Packet to client (mac address) reached max retries, removing the client'; I'm not sure why the client is removed. Does 'reached max retries' mean that the client has tried to many times to connect to the AP/Bridge?
View 1 Replies View RelatedIs the feature "event logging" that is present on ACS 4.2 with the option to "send all events to the windows event log" no longer supported in ACS 5.2?
View 1 Replies View RelatedIs it possible to automatically shutdown the OUTSIDE interface on a Cisco ASA 5520 in case of intrusion?.
In my opinion if there is an attempt of intrusion, just the device would stop it. If it cannot detect it, how can the device recognize the event and so shutdown the interface?. Am I correct?
i can't configure "logging event spanning-tree" on a specific port under IOS 12.2.(58) SE2 (all other "logging events" are possible), under 12.2 (55) it is possible. Is it now a known bug or a default value?
View 4 Replies View RelatedHigh Utilization event generated for Nexus 7010 shows in LMS 4.0.1. share your input why its generated. We have checked up Nexus, it showed not utilization.
View 2 Replies View RelatedI have EEM configured on cisco 3560 switch. The configuration is below. I want that switch inform me through email when device with particilular IP address become unavailable. I already try to debug this with debug event manager action mail but didn't see any output. [code]
View 2 Replies View RelatedSince we upgrade WLC in version 7.0.230 my PC with atheros card (version client 8.0.140 and driver 9.2.0.419) have brief interruption. In System events we have a lot of events ID 4201 and 1007. I try use Windows Wireless Client and we have not problem but the roaming is not fast. I don't find other client Utility for Atheros.
View 2 Replies View RelatedWhy the IOS on 4500 doesn't support globally, although am running the IOS 12.2,need for logging event link-status global.
View 3 Replies View RelatedI have a (single) client (it is a cisco IOS router) behind a wireless workgroup bridge (cisco1242).The client's IP address is obtained via DHCP from the wired network.Now, when roaming occurs, the Client will never have knowledge about this event,and hence will not renew its IP address until lease expiers. This is not a problem of course when Layer 2 roam occurs, but with Layer 3
roam it will interrupt the traffic.
The cisco's IP Mobile implementation does have this issue addressed in DCCoA scenario: the WGB is configured to send an SNMP trap on its dotradio state change;the cisco mobile router is configured with snmp-server manager to process this trap and start DHCP renew on the Down/Up event. Unfortunately, this works in Mobile IP scenario only because I cannot make it work without the mobile router registered with a home agent.
how to force DHCP renew on a client (cisco IOS router) in such a situation - event scripting, SLA, or ...?
when the supplicant is missing vlan500 is open for port and everything is ok, but when supplicant has wrong configuration something happend and port is always authenticating(every 30s, vlan500 is not assign to this port with bad configuration supplicant) and logs show something like that
Jul 10 10:20:12.362: %AUTHMGR-5-START: Starting 'dot1x' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A3545161E4 Jul 10 10:20:44.365: %AUTHMGR-5-START: Starting 'mab' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A45451DF11 Jul 10 10:20:44.399: %MAB-5-FAIL: Authentication failed for client (001e.3718.7297) on Interface Ga0/1AuditSessionID 0A0EFF5B000004A45451DF11 Jul 10 10:20:44.399: %AUTHMGR-7-RESULT: Authentication result 'no-response' from 'mab' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A45451DF11 Jul 10 10:20:44.399: %AUTHMGR-7-FAILOVER: Failing over from 'mab' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A45451DF11 Jul 10 10:20:44.399: %AUTHMGR-5-START: Starting 'dot1x' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A45451DF11
version - Cisco IOS Software, C3560E Software (C3560E-UNIVERSALK9-M), Version 15.0(1)SE2
port config:
interface GigabitEthernet0/1
switchport access vlan 104
switchport mode access
switchport voice vlan 200
authentication event fail action authorize vlan 500
[code]....
A customer has a wireless PTP bridge using a pair of 1410 bridges. The non-root bridge event log shows the RSSI polling information message indicating the link's signal strength; ie. -42 dBm. It updates every few seconds or so. The root bridge does not show this information in the event log. Both bridges have the event log configuration options set identically, all messages types are enabled. I can't find any reference to this in the documents. Is this by design? I thought that maybe a root bridge if it was set up as a multi-point might be overwhelmed if it was showing/scrolling RSSI from multiple non-roots.
View 3 Replies View RelatedThe WAG160N V1 you can change the dns primary default router for the connection "alice adsl 7 mega"? I would like to change it because in widows8, I keep giving every time the system event log, the error: "The computer was not assigned an address from the network (from the DHCP Server) for the Network Card with network address 0xF07D686CB987 . has encountered the following error: 0x79. Your computer will continue to make further attempts to obtain an address " I checked with the ping and the first two dns 85.37.17.15 does not work, while the second works 85.38.28.74. how to configure the DWA140N rev.B2 the property is currently configured as follows: IEEE802.11h = Disable Multimedia / Gaming Environment = Disable Country / region (2.4 GHz) = n. 0 (1-11) Country / region (5 GHz) = n. 0 (36-64, 149-165) Radio on / off = Active Selective Suspend = Disable Selective Suspend idle timeuot in senond = 5 Sensitivity roaming = Disable (options, max, min, average) Ad hoc support 802.11n = Disable
View 3 Replies View RelatedDisable wrr-queue cos-map on 6509 interface?.I have the following config on one of the interfaces that i would like to remove:
[code]...
I have a 3750X-24T in our production environment that is showing very high number of OQD's in the 'show int sum' output for 4 of the Gigabit interfaces; the interfaces are each in a seperate port channel and there are no OQD's for the relevant port channel and there are no output drops showing in the output for the 'sh int' command for each interface.
The following are the OQD's for the relenvant interfaces
Gi1/1/1: 0
Gi1/1/2: 0
Gi1/1/3: 0
Gi1/1/4: 0
Gi2/1/1: 4252879251
Gi2/1/2: 4251090833
Gi2/1/3: 4251754140
Gi2/1/4: 4294942102
Po1: 0
Po2: 0
Po3: 0
P04: 0
Gi1/1/1 and Gi2/1/2 assigned to Po1, and so on.
IOS version: C3750E-IPBASEK9-M 12.2(58)SE2
I have two goals on my Cisco 3750E -
* Limit bandwidth to match carrier provided bandwidth (10M ethernet port, but only 6M provisioned)
* Prioritize some traffic over others through the use of a priority queue.
I have come up with this design:
access-list 100 remark priority traffic
access-list 100 permit ip 10.1.1.0 0.0.3.255 any
access-list 100 permit ip any 10.1.1.0 0.0.3.255
[Code]....
How do I know? Is there a show command to show priority packets?
Am I right in assigning dscp 46 to this interesting traffic? That way it goes to queue 2?
Am I right in applying the priority-queue out command to the interface?
We also have voice traffic. But I think i can trust it to queue up into the router with trusted dscp
We're testing the reference system shown in the figure below. System Description Four 2960 switches are used for transport;Equipment 1 and Equipment 2 exchange packets for synchronization;To reach synchronization Equipment 1 and 2 must exchange data with a very low jitter. 2960 Configuration details Four our test puprose, we're using 100Mbit/s ports (22 and 23) as trunk.In order to obtain minimum jitter We performed these configurations:We Enabled QoS;We Marked Synchronization packets with CoS 7 and DSCP 63;We marked other kind of traffic inserted in different ports) with CoS 0;We set "trust DSCP" on trunk ports;On the trunk ports we mapped traffic with CoS 7/DSCP 63 (and only this) on output queue 1;We enabled the expedite queue (priority-queue out). QuestionWith these settings we aim at forcing our synchronization packtes to precede other kind of traffic and go from Equipment 1 to Equipment 2 with minimum jitter.Unfortunately we experienced high jitter when both synchronization packets and other traffic are sent through the systems.
View 9 Replies View RelatedI need to trust and prioritize voip traffic on my 6509 core
at the moment I have mls qos trust dscp on the interface
Is this enough? or do I need to enable the priority queue? how do i do this ? as it doesnt accept the priority queue out command like a normal switch
I am working on a QoS design which I hope to test at some point, but at this stage its from the books.My question is how to decide which queue and threshold to use for video traffic, then lower priority traffic.I understand the shaping and sharing commands, its the queuing and threshold bit I'm not clear on.The plan is to use the priority-queue for EF marked voice, this will be policed on ingress to provide an upper limit to EF traffic levels, then my second priority traffic will be video. Which queue will get serviced first once the priority queue is empty, and how do I decide which threshold to allocate my video traffic to? The document ion is not at all clear, I want to prioritse my traffic in the following order:
1 voice, use the priority queue
2 video, this to get serviced ahead of data, after voice.
3 interactive data
4 Bulk data
5 Best effort
So Q1 settings are ignored due to priority queue. Q2 gets 70%, Q3 25% etc.Is it as simple as putting video into Q2 T1, then interactive data into Q2 T2, will Q2T1 get a higher priority over Q2 T2 once the PQ is serviced?
We are facing output queue problems on our ATM interfaces. A lot of output queue errors are been shown as below.
Cisco 2811 -> ATM Link -> <-ATM Link <- Cisco 3945 Routers.
Cisco 2811 Version is 124-15.T9.bin
Cisco 3945 Version is SPA.150-1.M1.bin
Cisco 2811 Output Errors
We currently have a site with a very simple topology that uses a 3750X switch stack for a collapsed core. Everyday, the users have a conference call and experience poor voice quality.Its not bad when users call from several conference phones, but when everyone calls in on individual phones, there is choppy and almost inaudible voice quality experienced. The voice traffic flow would be as follows: Phone <-> 3750 switch <-> Voice GW We have packet captures showing that RTP packet loss is occuring from the phone to the voice gateway, but none from the voice gateway to the phones. We also have drops in the output queues that match drops on the asics. I can reset the counters and they will be clear until the call, and then they increment significantly during the call. The voice gateway and phones are non-Cisco. The switch stack has 6 switches. We are trusting the DSCP settings on the phones. All the queue drops from the phones are usually in queues 0-3, but all drops on the voice gateway is in queue 0. Below are the QoS settings; they are mostly default and we have not changed any queuing, thresholds, or buffers. Should we specify larger buffers and threshold for a designated queue and send EF traffic to that queue?
MySwitch#sh mls qos
QoS is enabled
QoS ip packet dscp rewrite is disabled
Typical Port
GigabitEthernet1/0/4
trust state: trust dscp
[code].....