Cisco VPN :: 861 Easy VPN Software Client Unable To Access Few Networks
Feb 19, 2013
I have access to network 10.3.1.0 /24 but I am not able to access 10.3.2.0/24 and other networks behind the Easy VPN server.I am using a software client to connect to the server.I have configured split tunnel to the network 10.3.0.0 /16 and it shows up in the route details too. I can ping 10.3.1.0 network but not 10.3.2.0 and so on.The Easy VPN server is configured on Cisco 861 with VPN module. [code]
Just setup a Cisco 2821 acting as the easy vpn server. All good, however, the easy vpn client, say for example doing a speedtest, is REALLY slow.
For example, both the client and server have 100M / 5M connections and doing some local speed tests thru the isp, on the client side we are seeing 4M/2M? We have very few vpn clients right now, so I can't see the Cisco 2821 being overloaded.
I have tried messing with the mtu, adjust-mss settings on the wan port on the 2821, but, no real changes?
I am supporting a small cluster of AP541N WAPs and would like to know if there is an easy way to manually disconnect an associated client (recognized by MAC address) from the Associated Clients screen in the Access Point Configuration Utility Status view. That type of feature might come in handy with unruly bandwidth hogs down the road.
Is it possible with ASAVPNSERVER 5520 and an EasyVPN 5505 Client to have the client do split tunnel to a single public IP address? Both devices are on 8.2(5) 33. Could you possible provide sample config for split tunnel?
I'm currently using DynDNS for my Dynamic DNS Provider with the RVS4000, but I'm looking at upgrading to the RV180 and switching my Dynamic DNS provider over to DNS Made Easy since I can get all my DNS hosting under one roof. Does the RV180 support DNS Made Easy in its Dynamic DNS client? If not, could it be added in a firmware update?
I just bought a WRT54GL which is working perfectly. I needed it to extend my home network for my kids (I have not a very fast internet connection and my kids are eating all of it... With the WRT54GL I can choose how much they can have. So my own network has a netgear modem and a netgear wifi access point which is in this network : 192.168.0.x.
This network is not blocked in any way (just password protected). For my kids network, the WRT54GL gives addresses in this network : 192.168.1.x and is limited in speed. Everything is perfect, I have internet connection on both of my network, There is just the problem that I cannot access my printers, my servers, my computers.... that are on the 192.168.0.x network from 192.168.1.x. Is there a solution ? I already tried to force the WRT54GL to go to 192.168.0.x network but no more connection. Should I "bridge" the two networks ? How can I do it ?
A user with Easy VPN client connects to a 876 ISR (router A). This router also has a site-to-site VPN to another 876 ISR (router B). What I want to achieve is that the user dials in to router A and can access the network on the remote end of the site-to-site tunnel (router B) In diagram:
user (192.168.18.x) - Easy VPN - Router A (192.168.16.x) - sitetosite - Router B (192.168.17.x)
I have added routes in router B to the 192.168.18.x network with router A as next hop, but I can't reach the other segment.
On my Windows 7 laptop, after connecting to my office Network using Cisco VPN clientThe entire Internet is utilized by the VPN. I am unable to browse the internet on my computer till I disconnect the VPN Client.
Very recently, we had implemented Site-to-Site VPN tunnel between two Linksys RV042 4-port VPN routers. Everybody in our remote site is accessing and sharing the data through this tunnel and it is working fine.
Now, we have a plan to implement the same for our mobile clients also. For this, we had followed all the basic configuration procedures and user got connected to Quick VPN tunnel. Here is a problem we had observed. The mobile client user is connected to the tunnel, but unable to access the office LAN from the PC.
I have an ASA 5510 running v8.4(3)9 and have setup a remote user VPN using the Cisco VPN client v5.0.07.0410 which is working appart from the fact that I cannot access resources on a secondary subnet.The setup is as follows:
-ASA inside interface on 192.168.10.240 -VPN clients on 192.168.254.x
I can access reources on the 192.168.10 subnet but not any other subnets internally, I need to specifically allow access to the 192.168.20 subnet,[code]
I recently purchased a Cisco 2911 to replace my Cisco 1711 router. I copied the configuration from the Cisco 1711 router to the Cisco 2911 router. Everything seemed to work correctly except when I VPN tunnel into the Cisco 2911 router using Cisco's VPN client version 5.0. I can ping the router LAN interface from my PC that is VPNed into the router but I can no longer ping or access the devices on the LAN side of the router as I did on the Cisco 1711 router. I don’t see errors in the log or hits blocking anything in the acls. It’s using the same configuration that I had on the Cisco 1711 router, and this did work on the Cisco 1711. The Cisco 2911 router is running IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M1, RELEASE SOFTWARE (fc1).
Here is the VPN clinet portion of the configuration: The LAN is addressed as 192.168.0.0/24. The router LAN interface is 192.168.0.1, which I can ping and access. I can't ping or access anything on the LAN (192.168.0.0/24) beside the router.
aaa authentication login vpnclientauth local aaa authorization network vpngroupauth local ! crypto isakmp client configuration group remote-clients key 6 xxxx pool clients [Code]....
I have configured an easy vpn server in cisco 1905 ISR using ccp.The router was already configured with zone based firewall. But when i try to connect my office using vpn client i can reach only upto the internal interface of the router but can't access the LAN of my company.Do i need to change any configuration in ZBF since it is configured as 'deny any' from outside to inside ? If then what all protocols do i need to match ? Also is there any NAT exemption for the VPN clients?
For reference please see my full configuration:
Router#sh run Building configuration... Current configuration : 8150 bytes ! ! Last configuration change at 05:40:32 UTC Wed Jul 4 2012 by
I have a Cisco 881 setup with the following VPN config.
[code]...
The client is able to connect just fine to the network via VPN, but I am unable to gain access to any of the local resources. I know 192.168.1.1 has SSH running and 192.168.1.50 has telnet running but if I try to connect to either using the correct program they just timeout. I am really at a loss on why the vpn connection connects but I can not gain access to any of the resources on the VPN network.
getting internet access via a easy vpn tunnel on a cisco 877 router. Basically we would like roaming users to be able to use the internet via the vpn rather than using a split tunnel. The reason for this is we have multiple sites that are tied down via external IP access lists for some services. We would like roaming users to be able to interact with these sites through the central router and use the routers external IP address to acess the secured sites. I know we can use a proxy but we also use some other non proxy bases services at these sites so would rather direct routed access.
I have a new customer that needs to send data to us occasionally, we normally install the Cisco VPN Client on their PC, but this customer has the same private network we do.
I know this could be done with NAT Policy on my ASA 5510 with a site-to-site VPN, but the customer does not want to change the network hardware or addressing. They have cable router with no VPN capability, and they don't want to spend any more money on this project.
Can this work if their are no duplication of IP addresses?
I am using an ASA 5520 running 8.2(4). My objective is to get a VPN client to access more than one network on the inside of the network, i.e., I need to VPN in with an IPSec client and be able to establish tcp connections to servers at 192.168.210.x and 10.21.9.x and 10.21.3.x, I believe I am close to having this resolved, but seem to have a routing issue.
I have configured a Remote access vpn on pix 525 with 7.2(4) code. After getting connected (with ip address assigned from the pool) i am not able to reach any of the internal networks. [code]
I have a laptop that won't find any networks, it did work a few days ago now it's just randomly stopped.Things I've tried;
-Changing the wireless to different channels. -System restore to a few days before. -Check and restarted the wzc serice mutiple times. -Check the drivers are ok.
Recently, I have found out that my laptop is unable to find any networks. I started using what I believe to be an ethernet cable to connect my laptop to the internet because it was faster than wireless. But when I removed the cable and try to connect wirelessly, the computer states that there are no wireless networks in range. I know the wireless adapter is broadcasting because my sister can connect wirelessly to the internet. My WiFi is on, but I can't find any networks.
My laptop can see available networks, but is unable to connect to any of them.I have run Microsoft Security Essentials and the scan comes back fine, ran CC Cleaner as well as Malware Bytes and those scans both come back fine as well.I have also re-seated my wifi card, as well as attempted a TCP/IP stack repair option.However none of these fixed my issue. What could be preventing my laptop from connecting to a network? I have also tried to boot into Safe Mode w/ Networking, and the pc is unable to connect there either.I have also disabled all security on my router, it is just an open network no security, broadcasting the SSID.
I have a Dell PC from around 2005. I have this router: [url]....All the wires are connected to my PC but I don't get the notification icon, nor is it in network connections window (just my old broadband modem). I don't want to go wireless as such but just use WIFI on my cell/mobile when in the house if I have haven't got my PC on.
i have a acer laptop running windows 7 ultimate. I am unable to connect to public WiFi hotspots. But i m able to connetc to ad hocs and my mobile WiFi hotspot
I have an ASA 5510 working in Routed mode for a company with the following networks. everything works fine as desired. Below are the interfaces, security and ip addresses .
I have ASA 5510 and configured client VPN or Annyconnect VPN, when I connect to the ASA remotely using anyconnect I am able to get IP address as configued, from Internal network I can ping and RDP that anyconnect VPN desktop, but the problem is from the remote anyconnect VPN client I am unable to access internal network, when I use ASA packet tracer and check traffic from internal to anyconnect pool of addresses it gives result ok, but when i use packet tracer to check traffic on outside interface from anyconnect address pool to internal subnet it always gives the packet is dropped at WebVPN - SVC, and I can find any where related configuration for that.
I am tasked with transferring all clients from one subnet to the other. I figure the nicest way to do this is to temporarily have the subnets talk to each other in an endeavour to avoid as much downtime as possible. The two internal subnets are:
192.168.0.0/24 192.168.43.0/24 (the intended migration network)
I am beating my head against the desk here as I dont seem to be getting anywhere after the changes I have made. The current configuration is as such:
A friend of mine had a 802.11b netgear router and all of her computers were running just fine on it so she says. She bought and installed a 802.11n router and bought usb adapters for all her computers and all work, except one, a Dell Optiplex 330 that runs Windows XP.Some drivers were missing such as her Ethernet Controller and a chipset driver but I was able to install those from the Dell website. She had not yet bought a new USB adapter for the computer, I tried using my D-Link adapter and I can see the network in the D-Link connection manager but in Windows when I go to view a list of wireless networks, it doesn't show any. I cannot connect to the network from the D-Link connection manager.
I recently found out my laptop (Windows Vista)...cannot connect to secured networks. I was to connect to router using ethernet cable before, then i can connect to an unsecured network just fine..i remember that 2 years ago i can connect to secured networks...
i can't provide the name or brand of the router since it is owned by the landlord and only provided me with the password
But I am connected to the internet somehow. There is no ethernet cord connected to my computer and the ethernet adapter is disabled. Also, when I add an SSID to my preffered networks list, it appears, but once I click OK, and bring up that same screen, it is no longer there. Yet, I am still connected to the internet. Wireless Zero Configuration is ON, The wireless adapter is ON, I am connected to the internet as I am typing this How do I get Windows to populate those two lists (the preferred wireless networks and available networks lists)?
There are a ton of posts about this issue, and I have tried everything. I have an ASUS Eee 1040 PC with an Atheros AR5700EG wireless network adapter running on Windows XP. I've had the computer for a couple years and it has worked fine, until recently. Using inSSIDer, I can view all wireless networks within range, but using Windows, I cannot connect to any wireless networks. It gives me the message that "No wireless networks were found in range." I had a few hotspots that I would regularly use and they are not showing up in the list of preferred networks. I know for certain that some of the hotspots that are within range are indeed broadcasting their ssid. I can only connect if I manually add a hotspot as a preferred network and configure it with the correct security settings. Even then, viewing available wireless networks gives nothing, and Windows doesn't remember the hotspot. Here is what I have tried:restarted Wireless Zero Configuration service checked windows files haven't changed using sfc /scannow in a command window updated the driver for the wireless adapter rebooted the computer kicked and screamed
At home, I have 2 laptops and 1 smartphones, I set up a wi-fi network with WEP (WPA2) key. Since then the Windows Wireless manger is not able to connect.
If I remove the WEP key, I am able to connect.
The Internet connection is good. I am able to connect a HP, a Lenevo laptop, an iPhone with the same WEP key - but Dell does not connect.
I am running Windows XP on Latitude E6410 with Intel i5 Core.
I have an Acer 3810T laptop and am running Windows 7 on it.The problem I've had is my WiFi has been unstable. For example for 5 minutes or sometimes up to an hour I can easily find wifi networks in range of my laptop but then out of nowhere it disappears and I don't find any networks but any other WiFi device will find my router so I know it's laptop related.I did some research on Google and found out this is an issue others have had with Windows 7 and it seems to be something to do with when updates are installed. I followed the advice to remove my WiFi drivers and reinstall them so I downloaded a file for the Intel drivers from Acer's website. I went into Control Panel and removed 2 devices that were related to WiFi. I then did a scan for hardware and found one wifi device, an Intel WiFI Link 5100AGN. I installed the driver for this one. The problem is I know I removed two and this is the only one the scan found and I can't remember the name of the other wifi device/driver I removed.Unfortunately ever since I did this my WiFi isn't working. In the control panel it shows all drivers are installed and working but when I click on the bars at the bottom of my screen no wifi networks show. I have tried going into the Network and Sharing Center and for example I select set up a connection or network and when I select Manually Connect to a wireless network it states "An Unexpected Error Occured" so I know something is missing that's allowing the WiFI to work.
I have an Alienware M17X-R3 and I’ve been experiencing several networking problems with it recently- most importantly that I can’t connect to any wireless network. It detects all the networks in the area, but when I select and try to connect to one nothing happens. I can still use a wired Internet connection, though. “Troubleshoot problems” or “Diagnose” just tells me that I have no preferred wireless networks. When I go to the Network and Sharing Center, the “Set up a new connection or network” button doesn’t do anything. When I go from there to “Manage Wireless Networks” the “Add” button doesn’t do anything.
I’ve tried disabling and enabling my DW1501 Wireless-N WLAN Half-Mini Card, and reinstalling the drivers. I’ve disabled the “Allow the computer to turn off this device to save power” option on all my network devices. I’ve used a system restore. I’ve run a scan with Malwarebytes and my computer had crashed by the time I looked at it again thirty or so minutes later; it had tried to restart but was unable to because there was “No bootable device”. I powered it off and started it up again and it worked fine. I also ran a Superantispyware scan that completed successfully without finding anything and immediately crashed, but restarted normally.
A few other things that may or may not be related:
-When I boot I get a message that says “Could not reconnect all network drives”
-When I booted I used to get a message from GoogleCrashHandler64.exe that said “C:Windowssystem32dbghelp.dll is either not designed to run on Windows or it contains an error.” When I went to msconfig and disabled all non-Microsoft processes under services and startup I no longer got the message.
We an 887m router in our office with an unmanaged switch. We have two networks, 192.168.0.x and 192.168.11.x connected to router on the same interface (192.168.11.253 is a secondary ip) but I can seem to be able to route packets from one network to the other. Internet traffic is fine from both networks. I can't see what I'm doing wrong here. I can ping the 192.168.11.253 (router) from the 192.168.0 network but nothing beyond that.
I tried this at home with no other config and its the same. Is this by design?
