Slave Router - Can't Get Into Menu
Jan 25, 2011
I have a two routers running from one connection first the master which is a Dlink dg500 - i think all is fine there. Secondly I have a slave router running all the wired/wireless things in the kids rooms its a netgear and when i say 'slave' I figured out if you put the input from the first router into port1 instead of input it works as a slave.
Problem is I need to get into the router menu on the netgear, it was ip add 192.168.1.1 then when i slaved it it was 10.0.0.1 - (I think) but I have tried recentley to get onto it and can't for the life of me. I have tried wirelessly and through ethernet cable but can't get the menu.
View 2 Replies
ADVERTISEMENT
Jul 4, 2012
I followed instructions on using 2 routers my master is a netgear wndr4000 and slave is a netgear wgt624 v3 i have dead spot in livingroom so i ran cat 5 cable to plug my smart tv in. I have old router so i was wondering if i could also have wifi in living room so i read thread and it works. Only one problem my router in living room is open and when i put a password on it, it wont let me login. How can i put a password on slave router?
View 11 Replies
View Related
Oct 17, 2012
So I have a dsl modem (Tplink TD-8817) that i connected to my other route that has wifi(CBV734EW ). I configured them using this thread: [URL]
Now the problem: My pc that is directly connected with lan to my wifi router has acces to the internet. However when i try to configure the wifi router by going to its ip (192.168.0.1) im getting "The webpage unavailable" error. And i am also able to connect to my dsl modem(192.168.0.2) The reason i want to configure my wifi modem is the fact that for some reason only 1 wifi device at a time seems to be able to have acces to WAN.
View 4 Replies
View Related
Jan 24, 2013
Region : UnitedKingdom
Model : TD-W8960N
Hardware Version : V4
Firmware Version :
ISP : Be Internet
I have a router supplied by my ISP which is effectively locked down, the wireless on that router give me a massive 35 Mbps (yes i know... awesome) so I wanted to get something that would allow me to stream movies wirelessly in the house. The setup I had before was Thompson DSL router downstairs (ISP router) running the DSL connection and Wireless, a TP-Link 200Mbps Power over Ethernet connecting upstairs to a Netgear ADSL Wireless router (somewhat flaky device). This router had DHCP disabled and a static IP address, I had configured wireless with the same SSID, password and channel as the ISP router and they were all happy and everything was working (most of the time except when the netgear would crash or the 35MB wifi was too slow to achieve what I wanted).
What I would like to do is this... ISP router downstairs with wifi disabled so it just handles DHCP and DSL connection, router upstairs (New TP-Link) running new WiFi, DHCP disabled (static IP address for Router) but connected to router downstairs through TP-Link Power over Ethernet.
I was hoping it was as simple as the Netgear router where disabling DHCP was enough for it to see the other router and just work but it isn't doing that
I can ping the ISP router but cannot get to the internet,
View 2 Replies
View Related
Dec 18, 2012
I have just been reading an old post about running a Slave Router off of a Primary Modem/Router. That all makes sense for the setup side of it. My question is about open ports for devices connected to the Slave Router.. For example, I have certain ports open on my PS3 for playing Call of Duty online. Will all of the traffic for these ports simply flow through the slave router or do I need to open up all the same ports on the Slave Router?
View 3 Replies
View Related
Jan 22, 2011
I have a belkin f7d2301 and I cannot access the startup menu it says startup not found I have remove program and reinstalled it. is the disc bad. i also cannot do auto updates because it can't find startup location.
View 2 Replies
View Related
Apr 17, 2012
How I get GUI Menu for CISCO Linksys WRT120 N wire less Router?
View 1 Replies
View Related
Dec 4, 2011
I am trying to upgrade the firmware on my WRT54GS wireless router. I typed in 192.168.1.1 into the web browser and got to the setup menu but there is not much on the page. There are no menu options and just some of the information is on the page. None of the menu headers are listed. Is there any way to reset this so I can get the menu to work again?
View 6 Replies
View Related
Oct 24, 2012
I'm fairly new to networking and need to migrate an old core to a new core. I have a 6509-e Switch that I had an RMA on one of my 720 sup cards. After receiving the sup card I swapped my slave out with the new one, expecting it to boot into ios. It booted into Roman. I tried to boot the image manually and it did the same thing. I also tried to boot from my flash and, again, booted into ROMmon.
Question: If i configure and change the boot to boot from image it tells me i need to reset or power cycle first. Will this reset the entire switch? As this is production I'd rather not.
I am at home now, but I can supply any logs/hardware model/configs tomorrow. I thought I would see if this is an easy fix.
View 23 Replies
View Related
Feb 29, 2012
I just purchased an E-3000 and when I log into the user interface it seems changing pages and saving settings takes forever. I click on a section in the router menu and it takes what seems like 30 seconds for the page to change or accept the new settings. It's not my browser it's definitely a Linksys Router issue. I updated to the latest firmware and latest Cisco Connect software as well. Is this slow user interface a normal thing with these routers?
View 1 Replies
View Related
Jan 12, 2013
I just purchased a Linksys Cisco E900 router and hooked it up to my Internet cable. The Internet service that my ISP is giving me is PPPoE, fiber link (100 Mbps).
I did the set up. I connected my computer (via Ethernet cable) and my laptop (via wireless) to the router.
Now... there are other wireless networks around me. The WI-Fi channel my router fixed to is 1, apparently - saw it from the settings. But I can't find a menu anywhere in the router's gateway (192.168.1.1) from where I can change the wireless channel, wireless bandwidth etc.
View 2 Replies
View Related
Apr 14, 2011
I have the revision b version of the dir-655. I'm having a couple issues which im not sure if are related to the dir-655 or something else.
I used to be able to do this, then all of the sudden (I may have changed something) I cannot anymore. The issue is: If I try and access my linux server using http://[My Public IP Address]/ from *inside* my LAN, It will time out and not connect. If I try and access my same public ip address from *outside* my LAN, it works fine.
My router was noticeably slow to respond when navigating the menu system. Then, I changed the ip address to 192.168.0.2 (previously it was 192.168.0.1) and all of the sudden its fast again. I tried rebooting and power cycling before I changed the IP and it was always slow using 192.168.0.1.
View 3 Replies
View Related
Oct 8, 2011
I'm trying to register my new linksys e2000-ew wireless router but it doesn't show up in the selection pull down menu. When I try the e2500 it says my serial# isn't correct.
View 5 Replies
View Related
Nov 18, 2011
I 'd like to use the access restrictions capabilities of the WRT610N v2. Unfortunely the "Access Restrictions" menu is missing in the admin GUI; I 've got all the others : "Set -up", "Wireless", "Security", Storage, Applications and Gaming, Administration and Status. I've checked the Firmware already and i'm using the very last one available on the cisco web site. I also noticed that I do not have the "Linksys by Cisco" text on the upper left corner as one can read on user guide but just "Cisco".
View 5 Replies
View Related
Jun 2, 2012
My westell 7500 my be on the same freq. as my microwave because every time that I turn on the microwave my speakers go out or make all kinds of noise
View 2 Replies
View Related
Mar 9, 2013
Tried E2 port IP 192.168.1.1 unable to connect what am I doing wrong. Petro-stuff
View 1 Replies
View Related
Feb 1, 2012
LMS 3.2 can't open Manu Device Troubleshooting only begin I will check manu Device Troubleshooting but LMS 3.2 can't show detail about Device and show error on windows.I need fuction Device Troubleshooting becouse ATP customer.
View 1 Replies
View Related
Nov 23, 2011
Just bought myself a TP-Link WN722N Wirless Adapter. Currently I have a Netgear WNA3100 connected which works fine but I to use the TP-Link to connect to a second network simultaneously.Here's the problem.The drivers installed just fine for the TP-Link adapter. Windows shows that its connected as a USB device (USB2.0 WLAN) and Network & Sharing Centre shows it is being "Wireless Network Connection 4"(The Netgear one shows as "Wireless Network Connection 2")However, when i try to use the TP-Link one to connect to a network, it doesn't show up in the "Network Connections" menu on the Taskbar, and when i disconnect the Netgear one it says that it can't find any wireless connections at all; note that "Network & Sharing Centre" still shows the TP-Link Adapter as being connected to the PC).Tried Reinstalling the TP-Link Software, updating it, etc. Restarted PC. Disabled Netgear connection. Physically Disconnected Netgear Adapter and still no luck.
View 2 Replies
View Related
Jun 7, 2011
How do I get into the westell 7500 menu to changed the ssid
View 5 Replies
View Related
Jun 13, 2012
After an upgrade from LMS 4.2 to 4.2.1 Legacy menu is completely empty. Is it a bug? If it's empty, how to get to some of DFM options (like rediscovery, discovery status etc.) They seem not present in "Site map".
View 4 Replies
View Related
Sep 11, 2011
I can not access the configure menu.
I try access with Serial cable blue DB09 / RJ45 on console port and serial ports on PC using putty or hyperterminal but any connection can not be done. The screen stay black and not show any text.
The computer found the port COM1 but i csn not access any information from Cisco router model 1841
View 1 Replies
View Related
Jan 15, 2013
Region : UnitedStates
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111108 Rel.40398n
ISP : AT&T
Everything seems to work fine except that there is no Wireless option in the menu. I updated the firmware and reset to factory defaults, but the wireless option still does not appear in the menu.
View 1 Replies
View Related
Mar 25, 2012
Using EMM as a nice friendly interface for their terminal server (ie router with NM-16A and octal cables)?when I ask the framework to run the following command it gets stuck will a blinking cursor and clear screen
<IOSExecCommand>"connect 10.1.1.1 2000"</IOSExecCommand>
however removing the port number allows it to connect fine.
<IOSExecCommand>"connect 10.1.1.1"</IOSExecCommand>
same symptom if iI were to replace connect with telnet
<IOSExecCommand>"telnet 10.1.1.1 2000"</IOSExecCommand>
even setting up an iphost does the same ie:
ip host R1 2000 10.1.1.1
<IOSExecCommand>"connect R1"</IOSExecCommand>
All of these commands work fine from the # prompt
View 3 Replies
View Related
Aug 10, 2011
I was configuring a new unit straight out of the box to test a configuration for a client. I got most of of the configuration done and was noticing the menus were quirky and so I check to firmware and discovered it was 1.1.16 (* down level).
I finished my setup and rebooted to complete the changes, when I went back to log into the console it would Actively refuses to connect . the first time after powering on it shows the page title as setup before failing
I have tried a hard reset ( 15 Seconds reset) but it does not work . it doesn't even reset the settings. (static IP etc still there)
how can I get it fixed / exchanged under warranty
View 1 Replies
View Related
Dec 1, 2010
I have a Cisco 501 and I can not get into the configuration menu of the Java console appears to me this script
View 4 Replies
View Related
Dec 14, 2010
I upgraded the firmware on my newly acquired DAP-1522 from v1.02 to v1.21 (the hardware ver is A1). But weird thing happened after the upgrade--the Setup->wireless network settings portion of the set up menu disappeared! I re-flashed the upgrade once more and it's still not showing. Reboot the AP--same thing!
[url]...
View 6 Replies
View Related
Nov 27, 2012
after recovering from the PPPoE-port-forwarding-fiasco I had with the RV180 (url...), I decided to try again with a Small Business Router from Cisco. This time I took the RV042G, hoping that the higher age of this product comes with a more mature firmware.So far the functions I need, work satisfying. There is only one issue: The subnet-mask is only configurable using a dropdown-menu. I've read the posts from the Cisco-Support staff saying, that this is because it is only a SMB Router. So, we are a small business and we use the 172.20.x.y net for several reasons. One of it is to distinguish and group several network devices using the third block of the IP. Eg. our printers IPs start with 172.20.5.x and so on.
My question is: Is it really impossible to change the subnet-mask dropdown-menu to a simple text-field in the frontend? Because it is possible to change the subnet to whatever one needs by a little cURL-magic: [code] This sets the new subnet-mask permanently (even survives a reboot and is displayed correctly on the system-status page) and I have not discovered any problems.The only thing is, if you change settings on the setup -> network page, the netmask is reset and you have to rerun this script.
View 0 Replies
View Related
Jan 29, 2012
I get a empty blue window when I try to open "port to VLAN"
We have upgraded the software but it doesn't work.
View 1 Replies
View Related
Sep 25, 2012
We currently have an issue with our main ISE. When logged in using the admin account (member of superadmin group) we no longer see the Profiling button/menu and also missing oter options in the GUI. On another standalone ISE we do see al those options?
Both are running on the same software version 1.1.1.268.We are using ISE 3395-K9 appliances
View 1 Replies
View Related
Oct 15, 2012
Today I had to reset the router completely to factory default, if I was adding services to the forwarding or UpNp service management, suddenly it stopped adding the new ones.Now after starting all over it's having the same behaviour, see below my services, normally you can have 30 rules in this list but I cannot add new ones now.
Now I want to insert a new service IMAPS for port 993 so I go to service management.Then press "add to list" see below for result.It is there, then press OK and the screen closes, now if I choose a service from the list, it is not there !!
View 5 Replies
View Related
Sep 29, 2011
I'm running a Windows Server 2008 Enterprise Edition server that is currently the domain controller, and a Windows 7 Ultimate client. I have a 'Test' user for messing around with group policy - anyway, on the client Start Menu it has 'Test User' which leads to some form of libraries folder. Is it possible to restrict the link without removing their name?
View 3 Replies
View Related
May 10, 2009
I did a clean install of Windows 7 64-Bit the other day. I installed all drivers that came with my PC's Hardware, all went smooth. INCLUDING: Installing the original Linksys WMP300N Software/Driver Disc. I'm not sure how it installed, since i have a 64-Bit OS. It says that "This device is working properly", although no "Power Managment" tab came up in its Properties Menu. I had to manually go to the Registry Editor and turn off Some "Power Saving Features", like it auto-turning off. That's all i did an i'v had NO problems with it. Although, I don't use the software, and never have, i prefer Microsofts. I'v also got a second PC with a different Linksys adapter(Non PCI One)working great on 32-Bit Win7. How to get it to work on Windows 7?
View 9 Replies
View Related
Jan 6, 2013
I am using a Belkin AC1000 DB Wifi Dual-band AC+ Gigabit Router with the Belkin Router Monitor on a Macbook Pro (mid 2012) running OS X 10.8.2. I recently installed the router and the Belkin Router Monitor and everything works very well. I have one concern, however: the menu button on the finder bar is not illuminated blue, as it should be, but gray.
View 1 Replies
View Related
