Cisco Routers :: 993 Adding New Services In Forwarding / Upnp Menu
Oct 15, 2012
Today I had to reset the router completely to factory default, if I was adding services to the forwarding or UpNp service management, suddenly it stopped adding the new ones.Now after starting all over it's having the same behaviour, see below my services, normally you can have 30 rules in this list but I cannot add new ones now.
Now I want to insert a new service IMAPS for port 993 so I go to service management.Then press "add to list" see below for result.It is there, then press OK and the screen closes, now if I choose a service from the list, it is not there !!
View 5 Replies
ADVERTISEMENT
Jan 24, 2013
I have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
View 2 Replies
View Related
May 17, 2011
I recently upgraded from Linksys WRT54G to D-Link DIR-655 firmware version 2.0. All the features are working as advertised however i am having difficulties accessing UPnP services in my network. I have a Samsung 55" internet enabled TV connected to the router and also have few devices that can stream over UPnP to the TV. The option to enable the UPnP is enabled in the router configuration however its not finding devices in the network ... comparing that with Linksys ... all i had to do is enable the UPnP and all my devices discovered each other and started streaming without any issue. What do i need to do in D-Link to enable the UPnP devices ...
View 14 Replies
View Related
Sep 13, 2012
I recently set up a an external hard drive as a UPnP media server through my router. My media devices and my computer can see the drive fine. My question is, what is the best way to add files to the drive? It seems like a hassle to plug it into a computer directly every time I want to add more files, and FTP is kind of clunky. Is there any sort of software I can put on the drive or any better way to drop files onto it?I'm using a Seagate 2TB USB Drive formatted as FAT32 connected to a lemonade-equipped Westell 7501 router. I understand that it may be that I'm trying to get too high tech with my $7 router, but it seems that there should be a better solution.
View 2 Replies
View Related
Jan 24, 2013
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP : Cable TV provider
It seems there is a bug with TL-WDR3600. As it can be seen in the following image, the UPnP is off:But my firewall on the computer is reporting flood of packets originating from the router (it's the routers MAC address and IP address):I don't know what ETH type packet is, 0026 might be hex (38 decimal as seen in the raw log). But port 1900 is definitely UPnP.At the router, the wireless switch is off, as well as all other options for sharing etc. This computer is the only one connected to the router. The router has been reset several times.
View 1 Replies
View Related
Mar 16, 2011
We have an ASA 5505 and I need to set up port forwarding for an unusual port number which will be used for FTP on an IIS server.It's a bit complex as there are 3 VLANs: these are called ISP, Server and LAN-side VPN. We need to add a TCP port 8521 forward from the server's IP in Server WAN to ISP WAN VLAN with public IP address.
View 1 Replies
View Related
Aug 10, 2011
I was configuring a new unit straight out of the box to test a configuration for a client. I got most of of the configuration done and was noticing the menus were quirky and so I check to firmware and discovered it was 1.1.16 (* down level).
I finished my setup and rebooted to complete the changes, when I went back to log into the console it would Actively refuses to connect . the first time after powering on it shows the page title as setup before failing
I have tried a hard reset ( 15 Seconds reset) but it does not work . it doesn't even reset the settings. (static IP etc still there)
how can I get it fixed / exchanged under warranty
View 1 Replies
View Related
Nov 27, 2012
after recovering from the PPPoE-port-forwarding-fiasco I had with the RV180 (url...), I decided to try again with a Small Business Router from Cisco. This time I took the RV042G, hoping that the higher age of this product comes with a more mature firmware.So far the functions I need, work satisfying. There is only one issue: The subnet-mask is only configurable using a dropdown-menu. I've read the posts from the Cisco-Support staff saying, that this is because it is only a SMB Router. So, we are a small business and we use the 172.20.x.y net for several reasons. One of it is to distinguish and group several network devices using the third block of the IP. Eg. our printers IPs start with 172.20.5.x and so on.
My question is: Is it really impossible to change the subnet-mask dropdown-menu to a simple text-field in the frontend? Because it is possible to change the subnet to whatever one needs by a little cURL-magic: [code] This sets the new subnet-mask permanently (even survives a reboot and is displayed correctly on the system-status page) and I have not discovered any problems.The only thing is, if you change settings on the setup -> network page, the netmask is reset and you have to rerun this script.
View 0 Replies
View Related
Jan 26, 2012
I am unable to make UPnP to work on the RV220W. I am forced to use port forwarding.
View 10 Replies
View Related
Mar 1, 2012
We require UPnP (mainly for an in-house built FTP Server app that uses UPnP to dynamically open/close ports for Passive FTP mode) and have found it's implementation in the SA540 is unreliable. Sometimes UPnP works after a reboot, sometimes it doesn't. When it does work after a reboot it will eventually stop working. Going into the web GUI and turning UPnP off and back on always fixes for a while.
Is this a known issue with the SA500 Series routers? We had an RV220W deployed first, but it's UPnP implementation was even more unreliable. That said, it seems that the latest Beta firmware version for the RV220W has fixed the issue. Could it be that the same fix needs to be applied to the SA540?I was planning on opening a cause with the CSBC at some point like I did with the RV220W, but I'd rather not spent the time doing so if the this is a known issue.
View 1 Replies
View Related
Sep 11, 2011
I have been unable to get the UPnP function to operate on this router. Box has been checked and saved several times with no results. Ports cannot be opened maunally as well. I have been through every page looking for something that was missed, along with the sparse documentation instructions to no avail.
UPnP and port forwarding worked fine on the residental E3000 router that this replaced. I thought this was an upgrade, but it is seeming like a downgrade now.
View 15 Replies
View Related
Jan 6, 2013
I am using a Belkin AC1000 DB Wifi Dual-band AC+ Gigabit Router with the Belkin Router Monitor on a Macbook Pro (mid 2012) running OS X 10.8.2. I recently installed the router and the Belkin Router Monitor and everything works very well. I have one concern, however: the menu button on the finder bar is not illuminated blue, as it should be, but gray.
View 1 Replies
View Related
Sep 16, 2011
I am trying to set up a custom service on my netgear configuration page. I have a netgear router model# Wnr834m. every time i click the "add custom service" button the page redirects to "system authentication failed" and logs me out. What can i do to set up the new port?
View 1 Replies
View Related
Apr 3, 2013
I have a Cisco RV016 router, with some ports configured in "Setup --> UPnP". Currently I have problems to configure new ports. I can create the service in "Service Management", but when I add this service to the list, I press "Save" and the router close the session. I need to re-login the router, and it don't save the changes.
However, if I add a service that was already exists before having this problems, the router save the changes (But the router close the session too).
The router has the last version of firmware since the first run.
View 4 Replies
View Related
Oct 20, 2012
How to enable UPNP on CISCO routers - 36XX , How can I simualte UPNP connections.
View 2 Replies
View Related
Sep 7, 2011
My ISP sends various services through VLAN. Internet, TV and Telephone.Now I wonder, is it possible to use this router to distribute these VLANs through the wan port to eg my IPTV box?
View 5 Replies
View Related
Aug 9, 2012
I have some questions regarding the addition of custom services and their use in QoS for RV routers (I use the RV220W). Suppose I create a custom service as:
Name: My Service
Port: TCP 60000
1. Does this port number refer to the port number used by my LAN computer or the port number on the other side e.g. some computer on Internet I am using this service to connect to? Some services use the same port number on the side that initiates the service and the receiving end but there are services that use different ports for the initiating and receiving end. So, what is the meaning of the port number when creating a custom service?
LAN Computer : (port TCP 60000) <----> Internet computer : (some TCP port, not necessarily 60000) - or -
LAN Computer : (some TCP port, not necessarily 60000) <----> Internet computer : (TCP port 60000) ?
2. Suppose I create a QOS profile binding configuration with respect to this custom service for a specific IP address on my LAN. QOS is applied to the outgoing network traffic only. How is this profile going to work?
A. Applied to traffic originating from my LAN device with the specified IP address and port TCP 60000 - or -
B. Applied to traffic originating from my LAN device with the specified IP address to another computer's port TCP 60000 ?
View 9 Replies
View Related
Feb 2, 2012
I have Ports open, with DNS named defined for internal services..
When extertnal they work by name just fine, so the firewall's working Ok. But when on the LAN they fail.
When I look at the port forwarding rules, I see Outside -> Inside, but there's no Inside -> Inside..
How can my LAN users use DNS Names/Ports that are on the WAN interface,,. so when they come between the WAN and LAN their apps continue to work ?
View 6 Replies
View Related
May 15, 2012
I need to access a shared folder over a VPN connection. Very simple host network: no Microsoft server, no AD. Just a WRVS4400N router and a peer-to-peer network.
Purchased a second WRVS4400N router to create VPN from SOHO and configured via VPN Setup Wizard.
When at the office, I can map a drive letter to a share on the other computer, as follows
net use f: \192.168.1.111MyShare /User:MYSELF mypass
However, when try same command over VPN, I receive the response:
System error 53 has occurred. The network path was not found.
I also cannot net view the other computer -- same error. However, I can successfully ping 192.168.1.111.
More info:
Routers have latest firmware.
Over VPN I cannot browse network via Windows Explorer (Win7 Network Neighborhood shows only my own PC. In the office I can see the other computer and the NAS appliance "NAS01").
I also cannot connect by entering \192.168.1.111MyShare into Windows Explorer's address bar (although I can do that successfully when at the office), or by choosing Map Network Drive from "Computer".
However, over VPN, I can get into NAS administration via https://192.168.1.3 and I can print to the office TCPIP printer (192.168.1.222)
View 4 Replies
View Related
Aug 7, 2011
Recently I'm having issues with accessing local services via external IP. Short description of configuration:
- sub.mydomain.com pointing to my external IP.
- few web services running on my local server with reverse proxy on Apache 2
- firewall on router enabled
- ips on router disabled
- single port forwarding: WAN 80->Lan 443, WAN 443->LAN 443
- accessing my services via sub.mydomain.com/service1, sub.mydomain.com/service2, etc
- I had to create a new rule in internet access policy allowing LAN, any, any to
Basicaly if I go no matter if I type http or https I will be redirected on 443. That configuration has beed working without any issues for a month. Recently I have increased the amount of DHCP users and suddenly it's not working any more. I can still access my services from outside but not from LAN.Restarting router does the trick for a while,sometimes for few minutes, sometimes longer.Enabling IPS is the way to go but then I'm limited to around 22Mbit/s. I have no idea what happend.What I can't understand that it was working, suddenly it's stopped and there are two solutions, either to enable IPS or to restart router?
View 1 Replies
View Related
May 27, 2012
I have two servers behind the RV180 and a list of ports I would like to open to the public (80, 443, 21, 3389).In that case, I have to setup 8 Access Rules. I am OK in the first time setting up.But later on, if I would like to change the external IP <-> internal IP mapping, I have to change the Access Rules one by one for all related ports.
Does it has a setting for grouping the ports together so that I can set the Access Rules by one time only ?BTW, the summary view of the Access Rules in RV180 is not very clear, I can't differentiate the Rules for different Destination NATs ... I have to click into the details one by one ...
View 1 Replies
View Related
Feb 9, 2013
We recently moved to a new office and currently have three ISPs(DSL, SAT, 4G) because we are unable to get Cable nor Fiber services. We have anywhere between 7-20 Remote Desktop connections(with lot of file transfers) and 8 VOIP lines. Basically, we need to bind certain services to specific WAN links in order to make everything work somewhat decent because of the limited bandwidth and/or latency of each ISP.
I would like to double check if the bindings are working for the specific services, and it has been difficult to verify if the settings in the RV016 are working. I believe it's not working 100%, and I need a way to check and make sure that my settings are being followed.
What would be the best way to check the current connections to see if the service is being routed via the WAN link specified in my setting? My RV016 is HW ver 3, but not the latest firmware. Purchased about 2 months ago.
View 4 Replies
View Related
Feb 11, 2012
I have 25 of these routers installed behind various providers and transport (DSL, Cable, UVerse). At sites where I have static IP, I can't reach any service inside, and in fact can't even reach the router for Remote Management. At all times the users indoes can do whtever they like, the have Internet access.
At sites where we draw a dynamic IP or use PPPoE, I can reach services and manage the router until a known issue stops the inbound traffic.
View 3 Replies
View Related
Jan 20, 2013
This would be the first time I will be working on NCS for a client. There is completely a new install and I was just doing my reading to get my head around the overall working of the product. I had a small Q in mind which I wanted to ask here, while going the config guide, i could not find the way to add a router to the NCS prime. W have ASR 1001 in use along with switches. I read in some forum that NCS supported routers but couldnt find the way in the config guide unless i am missing somewhere. The NCS version is 1.0
View 6 Replies
View Related
Dec 22, 2011
we have 2 thompson HDSL routers connected to the internet. we want to combine them to have higher bandwidth and load balancing so we attached them to a linksys rv042 router. we are running a Xbox applications that require high speed internet streaming.
if the RV042 can combine those 2 high speed internet connections, without disconnecting.
View 1 Replies
View Related
Jun 13, 2012
I am pretty new to Cisco networking and setting up a test router to use from home to connect into our network. My organization would like for us to provide upper management with home office setups to give them the ability to work from home. We will provide all of the equipment of course (router, phone and workstation). my boss wants me to use some of our old decommissioned equipment to set up a test home office to see how efficient and feasible it would be. I have a Cisco 1700 router, Altigen IP720 phone, and Dell Optiplex 380 workstation.
View 2 Replies
View Related
Aug 26, 2011
I have 3 subnets that I all want to have my RV220W (1.0.2.4) as the gateway. Where can I add an alias into the router so all three subnets and communicate with it?
View 1 Replies
View Related
Jan 25, 2011
I currently have 1 cat 5 jack at my tv/entertainment area and will be needing additional jacks to add gaming consoles,streaming video player and internet ready tv at the same location.The current jack installed at that location is coming from a D-Link 8 port Gigabit switch installed in a different room.The switch is at capacity,all ports are full,so no additional availability there.My question is how to expand port availability at the entertainment area.Is it possible to put another switch or hub at that connection?Would there be a conflict with cascading a switch from one to another? I have a 25 meg fiber optic incoming service,so there is plenty of speed and bandwith available to handle these componets.
View 1 Replies
View Related
Jul 28, 2011
I am somewhat of a neophyte at networking and I have a question. I have a small business network using a secure wireless router connected to my cable modem. We have a DVR security system which we would like to monitor remotely. I would like to keep the DVR separate from my secure wireless router for security reasons. My thought is to connect the DVR through a cable or wired modem into my cable modem. Do you folks think this will cause an issue with the wireless router which uses DHCP to determine the IP address?
View 1 Replies
View Related
Jun 3, 2013
I have a Netgear ADSL2 router connected to my main computer and want to add a new Belkin AC900db via plug link at the other end of my house so that we have wireless coverage throughout the whole house. It was working at first but the belkin needed an update which I did now It won't work at all?
View 3 Replies
View Related
Feb 27, 2013
Need to add a PIN for my wireless printer into the router control panel - ? Where do I find this control panel? Belkin F5D8236
View 1 Replies
View Related
Dec 22, 2011
Add wireless conection that can't see network. I have an existing working hard wired network. I want to add a wireless connection that has access to the internet, but not to the other devices on the original network.
View 2 Replies
View Related
Feb 8, 2012
I have a Cisco RVS4000 with Port 1 as a trunk connection to a Cisco SF300 switch. Port 1 on the router is configured 1untag,2tag,3tag,4ag. When connected directly to the router I can connect to the switches management IP. I would like to reach the switch remotely. I have set up DDNS and can access the router and I have have set a specific port to forward to port 80 on the switches management IP but this does not work. Should I not be able to Port Forward to the switch across VLAN 1?
View 3 Replies
View Related
