My ISP sends various services through VLAN. Internet, TV and Telephone.Now I wonder, is it possible to use this router to distribute these VLANs through the wan port to eg my IPTV box?
View 5 RepliesI have Ports open, with DNS named defined for internal services..
When extertnal they work by name just fine, so the firewall's working Ok. But when on the LAN they fail.
When I look at the port forwarding rules, I see Outside -> Inside, but there's no Inside -> Inside..
How can my LAN users use DNS Names/Ports that are on the WAN interface,,. so when they come between the WAN and LAN their apps continue to work ?
I have a Cisco RV220W router (firmware version 1.0.4.17).
I would like to have two separate networks with the following specifications:
Netwrork1: address range for the network is 192.168.0.1-254. All devices should be able to reach eachother within this network and connect to the internet either on LAN or through Wifi. From this network I should also be able to reach the device management page of the router. Also the devices should get the ip addresses throgh DHCP.
Network2: address range for the network is 192.168.5.1-254. All devices within this network should not be able to reach the devices in network1. All devices on this network should reach the internet through Wifi only. Device management page should not be available on this network.
I have configured the router as shown in the attached screenshots but the problem is that in Network2, devices get IPs from the 192.168.0.1-254 range and not from the 192.168.5.1-254 range. Also there is no internet on these either.
Just setup two RV220Ws with a IPsec VPN connection. All working well. However, I have a question regarding how to force ALL traffic from a VLAN to go thru the VPN.IPsec from site A (EU) to site B (USA) working good. On Site A I have a dedicated VLAN that needs to have ALL traffic (internet included) be sent thru the VPN tunnel. The main purpose of this is to have internet presence as if in the USA. This is necessary to access some sites available only in USA specially for the kids -their web sites will not display content because they're not in the USA at the moment. How do I accomplish this? I tried to setup a Static Route for the VLAN but you cannot setup a 0.0.0.0 destination route.
View 2 Replies View RelatedWe have a new optical fiber connection from a new ISP (only for Internet) and we found that our Cisco router RV220w won't work with this new connection because is not possible to add the V LAN ID 20 for the WAN traffic, as required by our ISP/connection. Now we would like to know what Cisco routers can support this feature and that can be "similar" to the RV220w or if there is another way to solve this problem and maintain our actual RV220w, because the features on this particular router (apart of the V LAN ID on Wan) are more than enough for us -
We would like to have a “simple” router and with firewall and VPN features as RV220w, because the one that our provider says that works seems to be too much for us Cisco 2951-SEC K9 – We are a small company with a network of around 10 computers and we only need some VPN connections for our sales companies in Europe and workers when traveling (3-5 VPN connections are OK).
I just received my rv220w and perhaps I haven't got enough experience with cisco routers. How can I restrict traffic between different VLANs?
For example: Hosts in one VLAN shall only be allowed to access a web server in another VLAN. All other traffic should be blocked. I've created two VLAN with Inter VLAN Routing enabled. But it seems there's no way to install a firewall rule between VLANs.
We assign (reserve by MAC actually) static IPs to all of our devices. Over time we have gotten rid of some devices but haven't begun (or finished really) re-using the old IPs. On our WRVS4400N v2 routers we are able to set the max number of DHCP users per Vlan. This prevents unauthorized devices trying to connect to our LAN.For example. I set the range from 192.168.1.100 - 192.168.1.103. IPs 100, 101, and 103 are in use (reserved via MAC address). We set max number of DHCP users to 3. This prevents someone from gaining access to 192.168.1.102. Does this make sense? Or at least this was the initial goal and it tested out successfully back when we implemented it.
How can I do the same for with the RV220W? I can set the range, assign static IPs (reserve IPs by MAC address), but can't keep others from gaining accessing to our LAN via the unused IPs (not assigned a static IP).My initial thought was to create static IPs (for the unused IPs) using dummy MAC addresses. I'm sure there is a much better way of accomplishing what I am trying to do.
I possess a RV220W (firmware 1.0.3.5) but I can't seem to work with the PPTP server on one VLAN only.
My default VLAN is in 192.168.1.1/24. I created a VLAN ID 10 in 192.168.50.1/24 inter-vlan routing : disabled and Device Management : disabled. (Menu Networking > LAN > VLAN Membership and Multiple VLAN Subnets).
Then I configured a PPTP server on the IP range 192.168.50.200 to 192.168.50.210.
To finish I created my user. (Menu VPN > IPSEC > VPN Users).
The PPTP tunnel is working, but on all my local network and not only the VLAN ID 10.
i'm using an rv220W and i whant to know if is it possible to assign vpn traffic to a vlan when i setup an ipsec tunnel?
example:
Im using different vlans on my rv220W.
Vlan 10: engineers (ex: 192.168.1.0/27) no intervlan routing
Vlan20: sales (ex: 10.0.123.0/24) no intervlan routing
This is what i need: - An engineer is on the road and when he makes a ipsec vpn connection => assignd to the vlan "engineers" so he can access the server/pc's in that vlan.and when someone from the sales group starts a vpn connection he needs to be in the vlan "sales" so he can access his pc/data,...
I picked up a pair of RV220W's and before I spent loads of time at a remote site, I figured I'd go through some VPN testing at home to make sure I could get it setup properly. What this means is I've plugged the Internet uplink into a switch, then from the switch into both routers & configured them (using unique static IP's for each) from there. For what its worth: While I have some IT experience, I don't have strong networking experience.
I setup several VLAN's on the local RV220W, and the end result is to make it so that an asset at the remote site with an IP in any of the ranges (192.168.121.0/24, 192.168.131.0/24, 192.168.141.0/24 and any future VLANs) can communicate with/access resouces at the local site. Likewise, an asset at the local site with an IP in any of the ranges (.121, .131, .141 + any future VLANs) should be able to reach the remote resources (currently just 192.168.181.0/24, but future VLANs as well).
This evening I tried to focus on the relevant VPN pages of the Administration Guide to get the VPN up. Leaving the defaults I got as far as establishing a link between both sites and it seems that things are working right: From the remote site (.181) I can access the local site (.121, .131, .141); and from the local site I can at least ping resources (a laptop) on the remote site. (Yay!)
However, when I physically connected an asset that had a 192.168.121.X, 192.168.131.X and 192.168.141.X IP addresses to the remote RV220W (which is 192.168.181.0/24), I couldn't see it from the remote or local sites.I assume this is expected. But I'm reaching out to the community to see what other possibilities might be available becuase networking is a weak area for me. I figured it might be something like a Static [or Dynamic] Route but I really am not 100% sure.
'TECHNICAL' SPECS
Local Router LAN/WAN Settings:
LAN IP: 192.168.121.1 on default VLAN (1)
VLAN 13 defined 192.168.131.1 with DHCP enabled; Reservations created outside of DHCP scope
VLAN 14 defined 192.168.141.1 with DHCP enabled, Reservations created outside of DHCP scope
Inter VLAN Routing enabled for all VLANs
[URL]
I have some questions regarding the addition of custom services and their use in QoS for RV routers (I use the RV220W). Suppose I create a custom service as:
Name: My Service
Port: TCP 60000
1. Does this port number refer to the port number used by my LAN computer or the port number on the other side e.g. some computer on Internet I am using this service to connect to? Some services use the same port number on the side that initiates the service and the receiving end but there are services that use different ports for the initiating and receiving end. So, what is the meaning of the port number when creating a custom service?
LAN Computer : (port TCP 60000) <----> Internet computer : (some TCP port, not necessarily 60000) - or -
LAN Computer : (some TCP port, not necessarily 60000) <----> Internet computer : (TCP port 60000) ?
2. Suppose I create a QOS profile binding configuration with respect to this custom service for a specific IP address on my LAN. QOS is applied to the outgoing network traffic only. How is this profile going to work?
A. Applied to traffic originating from my LAN device with the specified IP address and port TCP 60000 - or -
B. Applied to traffic originating from my LAN device with the specified IP address to another computer's port TCP 60000 ?
I need to access a shared folder over a VPN connection. Very simple host network: no Microsoft server, no AD. Just a WRVS4400N router and a peer-to-peer network.
Purchased a second WRVS4400N router to create VPN from SOHO and configured via VPN Setup Wizard.
When at the office, I can map a drive letter to a share on the other computer, as follows
net use f: \192.168.1.111MyShare /User:MYSELF mypass
However, when try same command over VPN, I receive the response:
System error 53 has occurred. The network path was not found.
I also cannot net view the other computer -- same error. However, I can successfully ping 192.168.1.111.
More info:
Routers have latest firmware.
Over VPN I cannot browse network via Windows Explorer (Win7 Network Neighborhood shows only my own PC. In the office I can see the other computer and the NAS appliance "NAS01").
I also cannot connect by entering \192.168.1.111MyShare into Windows Explorer's address bar (although I can do that successfully when at the office), or by choosing Map Network Drive from "Computer".
However, over VPN, I can get into NAS administration via https://192.168.1.3 and I can print to the office TCPIP printer (192.168.1.222)
Recently I'm having issues with accessing local services via external IP. Short description of configuration:
- sub.mydomain.com pointing to my external IP.
- few web services running on my local server with reverse proxy on Apache 2
- firewall on router enabled
- ips on router disabled
- single port forwarding: WAN 80->Lan 443, WAN 443->LAN 443
- accessing my services via sub.mydomain.com/service1, sub.mydomain.com/service2, etc
- I had to create a new rule in internet access policy allowing LAN, any, any to
Basicaly if I go no matter if I type http or https I will be redirected on 443. That configuration has beed working without any issues for a month. Recently I have increased the amount of DHCP users and suddenly it's not working any more. I can still access my services from outside but not from LAN.Restarting router does the trick for a while,sometimes for few minutes, sometimes longer.Enabling IPS is the way to go but then I'm limited to around 22Mbit/s. I have no idea what happend.What I can't understand that it was working, suddenly it's stopped and there are two solutions, either to enable IPS or to restart router?
I have two servers behind the RV180 and a list of ports I would like to open to the public (80, 443, 21, 3389).In that case, I have to setup 8 Access Rules. I am OK in the first time setting up.But later on, if I would like to change the external IP <-> internal IP mapping, I have to change the Access Rules one by one for all related ports.
Does it has a setting for grouping the ports together so that I can set the Access Rules by one time only ?BTW, the summary view of the Access Rules in RV180 is not very clear, I can't differentiate the Rules for different Destination NATs ... I have to click into the details one by one ...
We recently moved to a new office and currently have three ISPs(DSL, SAT, 4G) because we are unable to get Cable nor Fiber services. We have anywhere between 7-20 Remote Desktop connections(with lot of file transfers) and 8 VOIP lines. Basically, we need to bind certain services to specific WAN links in order to make everything work somewhat decent because of the limited bandwidth and/or latency of each ISP.
I would like to double check if the bindings are working for the specific services, and it has been difficult to verify if the settings in the RV016 are working. I believe it's not working 100%, and I need a way to check and make sure that my settings are being followed.
What would be the best way to check the current connections to see if the service is being routed via the WAN link specified in my setting? My RV016 is HW ver 3, but not the latest firmware. Purchased about 2 months ago.
Today I had to reset the router completely to factory default, if I was adding services to the forwarding or UpNp service management, suddenly it stopped adding the new ones.Now after starting all over it's having the same behaviour, see below my services, normally you can have 30 rules in this list but I cannot add new ones now.
Now I want to insert a new service IMAPS for port 993 so I go to service management.Then press "add to list" see below for result.It is there, then press OK and the screen closes, now if I choose a service from the list, it is not there !!
How do I submit an RFE (Request For Enhancement) to the Cisco SBR team to encourage them to implement the missing support for VLAN to VLAN firewall rules that was available in the RVS4000 (See [URL]) and that was supposedly added to a beta release of the RV220W firmware (See [URL])?
View 1 Replies View RelatedI have 25 of these routers installed behind various providers and transport (DSL, Cable, UVerse). At sites where I have static IP, I can't reach any service inside, and in fact can't even reach the router for Remote Management. At all times the users indoes can do whtever they like, the have Internet access.
At sites where we draw a dynamic IP or use PPPoE, I can reach services and manage the router until a known issue stops the inbound traffic.
I have a Netgear GSM7248R switch with 5 different Vlans including th management Vlan. Each of the vlans are connected to my layer 3 switch for routing. I want to access the management vlan form any of my Vlans so my layer two switch can be detected by my snmp manager.
View 3 Replies View Relatedwhat exactly is QuickVPN?Is it a IPSec VPN?Is it a PPTP?Is it a SSLVPN?can I resolve my local hostnames? That means, can I configure a lokal DNS Server?
View 3 Replies View RelatedI am trying to setup and configure a VPN on the RV220W that uses IPSEC so I can use the Cisco VPN Client I use at work, I have gone through the user manual 11 or 12 times now but still cannot work it out. I cannot find where on the Rv200W iset up the phase 1 authentication username and password which will then lead me onto the phase 2 stage of asking for a username password to allow me access.
View 8 Replies View RelatedPicked up a pair of RV220W's for a project I'm working on. I have several IP's available, 4 of which are assigned to/in use by a server behind the RV220W. All 4 of these IP's are static external IPs. How I can configure the RV220W so that requests to those 4 IP's get routed to the server.
Prior to purchasing this, I was under the impression what I was trying to do was called one-to-one NAT, but after reading the 'Help' document on the one-to-one NAT page, I don't think this is right. Emphasis added below: Cisco RV220W Wireless-N Network Security Firewall Help FirewallOne-to-One NATOne-to-one NAT is a way to make systems behind a firewall and configured with private IP addresses appear to have public IP addresses.One-to-One-NAT Rule TableThis table lists the list of available One-To-One NAT rules configured by the user. Private Range Begin: start ip address in private (LAN) ip addressPublic Range Begin: start ip address in the public ip address (WAN IP), Public IP Subnet Mask: The Subnet Mask of the public IPRange Length: Range length maps one to one private address to public address up to the given range.Service: This column shows service to be accepted by LAN Host.The actions that can be taken on One-to-One-NAT rules are:(Check Box At First Column Header): Selects all the entries in the table.Add: Opens the One-To-One NAT Configuration page, to add a new entry. Edit: Opens the One-To-One NAT Configuration page, to edit the selected entry.Delete: Deletes the selected entries.
So according to their documentation, the server in question would need to be configured with a private IP. Unfortunately, one of the applications I use is licensed via IP address and my understanding is that I cannot use the software with private/non-routable IP addresses.
Is the RV220W capable of not only securing the line (firewall, access rules, content filtering, port trigering & forwarding etc) but also doing what I was hoping to do (keeping the external IP's on the server, and routing appropriately)?
I'm using a RV220W router, and recently got shifted to a dynamic IP solution.Now, I've got a no-ip.org address, but the update service seems to be on no-ip.com. So, I try to enter mydomain.no-ip.org OR mydomain.no-ip.com in the dynamic dns settings, under Host and Domain Name, but when saving the settings it says
'The hostname specified does not exist in this user account' ,which seems to indicate that it manages to login to the update service but gets a negative reply.Is it possible to use the RV220W with no-ip.org/com?
We have 2 sites connected thru 2 RV220W routers via VPN and most things are working fine. I have noticed however, that any device that has a web interface, i.e. our Sharp Copier and our Freenas server, is inaccessible. The page tries to come up but then I get the Cisco "server is down" page generated by the RV220W.
I can pull up the web interface pages if I use a machine on the local LAN but not on any machine across the VPN. The only commonality I can think of is the RV220W blocking that traffic for some reason..
Cisco support write down manual (workaround), how to setup IPsec VPN connection on Mac OS 1.7?
View 5 Replies View RelatedIs there anyway to associate a name to an IP in the RV220W? I am coming from a WRVS4400N v2. Folks are complaining that they can't connect, for example via Real VNC, via the PC name any longer. They have to use the IP address. In the past I put the names of the PCs in the WRVS4400N when I reserved IPs via MAC addresses (some call this assigning static IPs). There isn't any place in the RV220W to put the name. Even when I look at the DHCP list a lot of them show up as "unknown". I am sure this is a NETBIOS thing but I'd rather fix this in the router as I have always done in the past.
View 4 Replies View Relatedi have a RV220W and absolutely nothings functional on this stupid Router, no NAT , no Port Forwarding and I cant access my Network from Outside. Any firmware link for downloading. This address works, its handling special webrequest.
View 1 Replies View RelatedI set up a PPTP VPN with an RV220W recently. It was working flawlessly until a recent power outage and now users are getting the 807 error when attempting to connect. I have PPTP passthrough enabled and TCP/UDP 1723 open. As far as I can tell GRE 47 is open as well. Why it was working and is not working after a power outage?
View 2 Replies View RelatedHaving a strange problem that just started this week and got worse this evening. I have a RV220W that is feeding my network. The RV220W sits behind a broadband modem and acts as the DHCP for the network and those computers access the internet that way. Anyway, tonight started an issue where the the RV220W just disappears. Becomes unpingable. I recycle power, and within anywhere from 5 to 10 minutes, it's gone. No longer pingable. Even if I plug a latop directly into it.If I power cycle the RV220W it comes back and I can ping it and access it and its settings. 5 to 10 mins later, I again lose it. Nothing was done. Its been working fine for a few weeks. Had a similar outage last Tuesday, but a recycle of everything brought everything back into line. After I lose connection to it, the lights I expect to be lit remain lit.
View 1 Replies View RelatedI am unable to make UPnP to work on the RV220W. I am forced to use port forwarding.
View 10 Replies View RelatedNothing happens when clicking the SAVE button after making changes on the VLAN Membership screen when using IE9, but it work fine with IE8. Any problems using IE9 during configuration?
View 4 Replies View RelatedWhen someone downloads a file, or similar, there seems to be no, or very little, room for other requests. I've even tried to be the only one on the network, start a download (from ex. Intel) and then tries to access a simple website, almost only text, and its extreemly slow. I hav ethe latest firmware, a windows domain network and the routers is not acting as dhcp server.
View 4 Replies View RelatedWhere I can find the MIB files for RV220W router?
View 2 Replies View Related