D-Link DIR-655 :: Difficulties Accessing UPnP Services In Network
May 17, 2011
I recently upgraded from Linksys WRT54G to D-Link DIR-655 firmware version 2.0. All the features are working as advertised however i am having difficulties accessing UPnP services in my network. I have a Samsung 55" internet enabled TV connected to the router and also have few devices that can stream over UPnP to the TV. The option to enable the UPnP is enabled in the router configuration however its not finding devices in the network ... comparing that with Linksys ... all i had to do is enable the UPnP and all my devices discovered each other and started streaming without any issue. What do i need to do in D-Link to enable the UPnP devices ...
View 14 Replies
ADVERTISEMENT
Jan 24, 2013
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP : Cable TV provider
It seems there is a bug with TL-WDR3600. As it can be seen in the following image, the UPnP is off:But my firewall on the computer is reporting flood of packets originating from the router (it's the routers MAC address and IP address):I don't know what ETH type packet is, 0026 might be hex (38 decimal as seen in the raw log). But port 1900 is definitely UPnP.At the router, the wireless switch is off, as well as all other options for sharing etc. This computer is the only one connected to the router. The router has been reset several times.
View 1 Replies
View Related
Oct 15, 2012
Today I had to reset the router completely to factory default, if I was adding services to the forwarding or UpNp service management, suddenly it stopped adding the new ones.Now after starting all over it's having the same behaviour, see below my services, normally you can have 30 rules in this list but I cannot add new ones now.
Now I want to insert a new service IMAPS for port 993 so I go to service management.Then press "add to list" see below for result.It is there, then press OK and the screen closes, now if I choose a service from the list, it is not there !!
View 5 Replies
View Related
Aug 7, 2011
Recently I'm having issues with accessing local services via external IP. Short description of configuration:
- sub.mydomain.com pointing to my external IP.
- few web services running on my local server with reverse proxy on Apache 2
- firewall on router enabled
- ips on router disabled
- single port forwarding: WAN 80->Lan 443, WAN 443->LAN 443
- accessing my services via sub.mydomain.com/service1, sub.mydomain.com/service2, etc
- I had to create a new rule in internet access policy allowing LAN, any, any to
Basicaly if I go no matter if I type http or https I will be redirected on 443. That configuration has beed working without any issues for a month. Recently I have increased the amount of DHCP users and suddenly it's not working any more. I can still access my services from outside but not from LAN.Restarting router does the trick for a while,sometimes for few minutes, sometimes longer.Enabling IPS is the way to go but then I'm limited to around 22Mbit/s. I have no idea what happend.What I can't understand that it was working, suddenly it's stopped and there are two solutions, either to enable IPS or to restart router?
View 1 Replies
View Related
May 30, 2011
How do I block a particular IP from accessing my network entirely? I have a hacker with a known IP I want to shut out. I tried creating a DENY inbound filter (with just that IP as the range) but that didn't seem to work. that hacker kept being able to attempt logins.
View 7 Replies
View Related
Aug 22, 2012
If possible I would like to have access to my external hard drive from outside of my network.While in the network my laptop connects to the Hard Drive using the shareport. If I take the laptop with me then I would also have to take the External Drive with me.
View 6 Replies
View Related
Feb 1, 2011
Is there any way to access the router's configuration pages (192.168.0.1) via the Guest wireless network when routing between the zones is disabled?
Here's the story:
I am using my landlords wireless internet, but I administer the router myself. The router is 'upstairs' and i am 'downstairs' and he has his computer plugged into it plus one wireless laptop. He knows nothing about computers and is vulnerable to downloading viruses (and other ****) and I don't want my computers to be on the same 'network' as his.
I had a brilliant idea that since I am 100% wireless, I can make a guest network, put all my computers on that network and disable routing between them. Now all of my computers (some connected through a wireless bridge) can not see his computers at all (perfect!). The only problem now is I can no longer access the router config pages at 192.168.0.1!
Is there any way I can segregate my computers from his and also access the router config? I've tried accessing the WAN IP for the remote admin pages from inside the NAT, but it still blocks it.
View 6 Replies
View Related
Jul 15, 2012
Just upgraded my system. I am using D-Link 615 as access point hardwired LAN to LAN to ActiveTec MI424WR N capable Verizon Fios Wireless Modem/Router. The Fios Router is set up with WPA2 security. Intend on having three 615s as Access Points off of ActiveTec. Have a number of wireless devices accessing the network. Have followed instructions from manual to use 615 as Access Point, disabling UPnP and the DNCP Server function on the 615. My ActiveTec IP address is 192.168.1.1 and I changed the 615 to 192.168.1.50. I can type this IP address in my browser and get to the 615 set-up.
I have tried a couple different options in naming the SSID on the 615 set-up. If I name the SSID on the 615 the same as the ActiveTec router, when I go to Connect to a wireless signal where there is overlap, there are two signals that one can connect to, named the same SSID, the Fios is WPA2 secured and the 615 is not. Shouldn't these all be on one SSID? It seems that I have two different networks (different SSIDs) instead of one (rather than the 615 simply serving as an extension of the Fios router as a wired remote access point) with different security protocols (WPA2 and None). The SSID name almost seems meaningless. If I name the 615 SSID the same as the Fios router SSID or something different, I still have the option of selecting one SSID that is secure and one that isn't. If I try to connect to the SSID name associated with the 615 I can get on without providing a password.How do I make it so that one can walk around and go from one area to the next and seamlessly move to the best signal? I did read to select different sets of channels for each access point.
View 3 Replies
View Related
Jan 14, 2013
UPnP seems to be failing somewhere between a few hours and a few days. It will work as expected for a while after starting or restarting the router, but then trying to create any new UPnP mappings will fail, and the ones that have been already created usually stop working. The commandline client upnpc fails to locate the router automatically, and manually navigating to http://192.168.0.1:65530/rootDesc.xml in Chrome returns a connection reset error instead of the expected XML device description.I turned on debug messages in the logs, but there doesn't seem to be anything useful in there (though they also seem to be flooded with a bunch of IPv6 mDNS network hopping, so I'm going to try disabling that for a while and see if that works). I did update to 2.10 and still had the same issue with UPnP, however my wireless network kept going down (I guess a known issue) so I downgraded back to 2.07. After the downgrade, I reset the router and manually re-entered all my settings (i.e. I didn't import them).
View 14 Replies
View Related
Jan 9, 2012
Just replaced a long-serving WRT54GS with an E2500 to gain a single feature… DHCP reservations for a bunch of web cams around my home. So far, the owner/user-experience with the 2500 has not been as positive as it was for the 54 or any of it's predecessors here and at my business. They just worked when you set them up, and once set up, they stayed set up. Zero futzing around with details. Some issues I'm seeking more expert input on:
My Panasonic Viera DVD/blueray player can access the web. Worked fine on the 54… access "Network" and 50% of the time it would join the network then and the other 50% of the time, you had to try a second time which I presume was the time it took for the device to gain access to the network. With the 2500, you can't ever (so far) get on by selecting "Network"… you have to go into the sub menu and have it dwell in the Network menu where it appears to make an ongoing effort to get onto the network. About 30% of the time, you get on… the other 70% no joy.My HP wireless printer will join the network if you dive into its menu system and tell it to look for the network. However, sitting at any of the computers on the network, you can't "get the printer's attention"… it just doesn't join and the print fails. You go over and use the printer's menu manually to get it on and it stays on for a short time, but it soon quits and that's the ball game.My Google Nexus One phone is a slightly different experience… it goes off the network as soon as you shut the screen down but, it seems like it comes back when you turn it on. With the 54, it seemingly remained in touch with the network better… things came in over the net while it was in my pocket. So, works better than the other two but I don't see why it goes away when on the 54 router, it didn't seem to.
In case it matters, this system is set up with DHCP, WPA2/personal and MAC filtering as was the case on the router(s) it is replacing. UPnP has been disabled. On 1.0.03 of the firmware. There are 6 DHCP reservations which also receive port forwards. I have adjusted the Beacon Interval, Frag threshold and RTS threshold for both frequencies and the MTU, all in accordance with recommendations under the support area for this site. Since everything worked well for both the 54 and its predecessor, I have to believe it's the 2500 that's the problem.
View 3 Replies
View Related
Jan 25, 2011
I just bought Air Video for the ipad, It needs support for the UPnP or NAT-PMP protocols, so does the wireless n do set this up automatically or do you have to manually configure the router, and if so how.
View 1 Replies
View Related
Jun 23, 2011
I have a DCS-930L network camera that I configured from its Web-based interface. In SETUP | Network Setup, I have disabled both UPnP and UPnP Port Forwarding. In my router's (Netgear WNDR3700) settings, I reserved the local IP address, 192.168.1.80, for the DCS-930L. In the DCS-930L I assigned the network camera HTTP Port 8000; therefore, I can access the DCS-930L on the LAN from [url].... In addition, in the router, I have forwarded port 8000 to the local IP address, 192.168.1.80, so I can access the DCS-930L from outside the LAN.I can access the DCS-930L both from within the LAN and outside of the LAN.
However, even though UPnP and UPnP Port Forwarding in the DCS-930L are disabled, the DCS-930L keeps adding and deleting UPnP NAT rules in the router. In addition, a system at the IP address, 207.232.83.172, keeps attempting to access the DCS-930L from different ports. I traced the IP address, 207.232.83.172, to the ISP, Telekenex, in Los Angeles, California. A partial log from the router is below.[code]...
View 2 Replies
View Related
Jun 24, 2012
My Dlink DIR-655 is hardware ver B1 and firmware 2.00. I found the UPNP cannot cross between wired and wireless network. It is fine if both UPnP server and renderor are on either network. There is no problem on other protocol, such as SAMBA from my notebook connected via Wireless to the QNAP NAS connected via Wired to the 655.
View 9 Replies
View Related
Dec 22, 2012
Region : UnitedStates
Model : TL-WR842ND
Hardware Version : V1
Firmware Version : 3.12.22
ISP : Bright House Networks
I'm having a problem as my PS3 keeps showing up as UPnP not available even though it is turned on in the router menu. What can be the cause? I want to say there is something wrong with the PS3 and not the router.
View 6 Replies
View Related
Feb 28, 2013
Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP : Comcast
Why am I unable to "disable" the UPnP in my TP-LINK TL-WR1043ND wireless router? When I click on the "disable" button nothing changes. I click on the "disable" button that then click of "refresh" and it still doesn't change to disabled.
View 3 Replies
View Related
Feb 11, 2013
In my Ipad (I have Dlink+), I can only see 1 minute of the Cameria 942L...the faq says that I need a conection witn Upnp.I have a Cisco EA2700 and I check the box of Upnp,,but I still cant see my camera from more than a minute,, then I have to reload.
View 2 Replies
View Related
Aug 31, 2011
Can I use Sharepoint print services with a macbook pro and a Vista 64 desktop?
View 3 Replies
View Related
Oct 4, 2011
i have a WD My Book Live and it's connected to my DIR-825. i'd like to configure the router to allow FTP access to the NAS from the internet. the drive has an option to enable FTP in it's configuration, but i have not done this before and i don't know what to do to create a solid/secure FTP portal so that i can access my files remotely.how do i configure the router for this ? my router is set to DHCP and i have turned MAC filtering on.. in particular i am looking for the ability to transfer/copy files from the drive, and not allow any modification/writing to the drive from the outside.
View 10 Replies
View Related
Apr 15, 2011
I've been having some issues with my network connectivity for a while now, and I haven't been able to figure out what the problem is. I run a wired connection to an Ethernet port in the wall of my university dorm. I have verified that it is not a global network issue or an ISP issue; this problem only happens on my PC.My network connection drops/disconnects randomly throughout the day. When I say disconnect/drop, I mean that all attempts to ping or access the internet fail. A few minutes pass before the Network and Sharing center task tray icon shows a warning sign saying that my computer could not connect to the internet.This is temporarily fixed by doing an ipconfig /release and ipconfig /renew, but I have to execute these two commands about 2-3 times a day on average.
There is no exact interval between the disconnects, nor does it happen when I am running particular programs. The disconnect happens regardless of what I am doing at the moment (gaming, browsing the internet, leaving the computer idle).A month back, I installed some Windows Updates and suddenly my internet connection was almost completely broken. I was experiencing the same issue, but much more frequently. My internet would die within 10 seconds of executing any download, but Windows wouldn't recognize that something was wrong. At first I thought the ZoneAlarm, Avast!, or the SafeConnect (as required by my university) services were causing trouble but uninstalling/disabling these services did not fix the problem.I also tried reverting to my default ethernet drivers, which did nothing. I uninstalled and reinstalled multiple versions of my drivers to no avail.However, the internet worked just fine in Safe Mode with Networking, so I cross-referenced the processes/services running in Safe Mode w/ Networking against my normal startup, guessing something else was at play.After some poking around, I discovered that disabling the Server and Browser services permanently fixed the issue of instant connection death. But the initial problem I described still remains;random, less frequent internet connection drops.
View 1 Replies
View Related
Apr 13, 2011
My system problem is after starting the computer within 5minits network services are disabled and network path not connected but communication is working when i am testing the ping command.
View 1 Replies
View Related
Jul 5, 2011
i want to connect two different internet connection on one network?i have on wi-tribe internet connection and one super net internet connection and i want to connect these to internet services on my one company network.
View 1 Replies
View Related
Dec 6, 2011
Any step by step instructions (for the DIR-655) on how to block a PS3 from accessing this router? I know how to log into the router's page and I can get the MAC address of the PS3, but I am clueless from there. I want to block it completely is possible.
View 7 Replies
View Related
Jan 11, 2013
i have a question about accessing shared folders over the WAN-Port of an DIR-615. For your information: both sides of the network (LAN and WAN) are under my control.
On the WAN-side of the network we have a fileserver with shared files. We can ping the server and reach it and the Websites on this server are also reachable from the LAN-side. But if we try to access to the shared folders the request doesn't reach the server. If we change the router there are no more problems and anything works without problems. The Router has default-settings except the network-settings so it works in our network. Does this router block outgoing traffic on ports 135-139 and/or 445? And when yes is there any way to disable this? I can't find it.
View 4 Replies
View Related
May 26, 2011
I recently purchased the dir-655 router, and am impressed by it's speed. I had no problems configuring the router to my liking, and have found that all of my wireless devices communicate with it flawlessly.
However, my main reason for purchasing this router was for the USB port. I had hoped to connect my 2TB external drive and have it accessible by all wireless devices in my home. To my understanding, the USB port relies on the use of the Shareport Utility. I've installed the Shareport Utility to my laptop for wireless access to my media files for streaming.
Here's my problem. How can I access my media on my external HDD connected to the dir-655 with Apple TV2? I've read several options for PS3 users... and they all seem to involve leaving the pc/laptop running. I would ultimately like to bypass the necessity of leaving my laptop on... but if that's not a possibility, I can live with it being left on.
Therefore, is it possible to access the external drive connected to the dir-655 with my Apple TV 2 by using the laptop as a bridge? Can I access the content via Apple TV by using Windows SMB just as I currently do to access media stored on my laptop?
To summarize, I want to have access to the media on my external drive connected to the dir-655 via Apple TV2.
View 1 Replies
View Related
Sep 1, 2012
I have a DIR-615 router. I would like to know if it is possible to block a PS3 from accessing the internet completely, without blocking any other computers/devices. I have access to the router, but not to the PS3 itself.
View 3 Replies
View Related
Jul 16, 2012
Dir 615, hardware version E4, Firmware version 5.1.Intermittent (95% of the time), problem accessing Google using my Android via wireless. A PC using XP on the same network has no problems. Using the Android on my local library's network I have no problems.Have restored to factory default settings and reconfigured with no improvement.
Modem setup: Setup to connect to another router, UPnP disabled, DHCP server disabled, 802.11 mode -mixed 802.11n & 802.11g (Android connects using 802.11n PC uses 802.11g have forced Android to use 802.11g to no avail), Auto channel scan, (have tried fixed), Channel width 20/40, visible mode.Internet connection Dynamic IP of course it is going out through my other Dlink ADSL 2 modem router. Also disabled QOS engine.
View 9 Replies
View Related
Mar 9, 2011
I am wondering if all routers that have a USB port to which network storage can be attached, support the functionality to enable that storage to be accessed from outside the network. If this is true how (in a conceptual sense) can the router be configured to do this and what are the security implications?
View 2 Replies
View Related
Jan 31, 2012
win 2003 dhcp server. when I leave dhcp services OFF i can ping the server fine. once i turn ON dhcp services the connecting drops in and out.. what is going on here?
My users are unable to get a steady connection to the dhcp server.
View 8 Replies
View Related
Feb 25, 2012
I have some questions about monitor of status of services on Network Devices such as HSRP, Etherchannel (between Access ports and Servers), etc. How we can track those information in addition to Syslog. Is it possible that the Fault Monitor displays them?
View 1 Replies
View Related
Mar 28, 2012
I've had a Linksys WRT54GS running DD-WRT (build 14929) for a while. I recently bought another Linksys (Cisco) router (WRT160NL) and installed DD-WRT on it (build 16785).
I'd like to keep the WRT54GS as my main router since it is very stable and use the WRT160NL as a network switch, NAS device, and asterisk server. I already have samba installed, configured, and running fine on the 160. However, the 160 is running as a router so only devices connected to it can access network shares.
How can I configure the 160 so that all devices in my network can access its network shares?
View 1 Replies
View Related
Oct 19, 2011
So i have set up my Dir-615 router and it worked for about a week perfectly. Then one day i was able to connect to the router, but it says that there is no internet connection. This is untrue since i am able to connect to the internet if i unplug from its WAN port and put it straight into my laptop.
View 8 Replies
View Related
Dec 26, 2011
I need to know how WLC can support ISE guest management in wireless mode. Tested and confirm by Cisco SE, Knowing that WLC currently does not support dynamic VLAN authorization for central web authentication. This limitation will be addressed in WLC 7.2 when MAB and CWA support is added to the code. On the other hand, DACLs on the other hand works and we can use that to restrict access of this guest traffic.Can ISE support on WLC LWA guest access provision? This able to view guest user login and show at ISE monitoring.
View 1 Replies
View Related
Mar 7, 2013
Region : India
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP : Lexus
I am using tp link router for accessing internet in my laptop and mobile. everything is opening in my laptop but i had few problems when using internet in mobile. im using android mobile. when using play store the images and screen shots of applications are not loading but im able to download. I'm unable to see the images in play store. So I'm thinking that there is something problem in router settings.
View 4 Replies
View Related
