I have an inventory added to Ciscoworks and am getting alerts on interfaces that I want to exclude but for the life of me I can't figure out how to exclude interfaces. Any tips on how to exclude interfaces from the fault engine in 4.1.
View 3 Replies
8.4(3) I need to outside PAT all incoming UDP (SIP/RTP) traffic from outside to an internal IP. The following command makes it work:
nat (outside,inside) source dynamic any obj-10.0.0.173 service udp udp
But it breaks DNS resolution from inside. If I add the above command and try to nslookup from inside to an outside DNS server 64.90.175.90, DNS times out. If I remove the above nat command, it works again. It seems like even though DNS UDP originates from inside which should create a statefull connection, ASA still messes with return DNS responses.I then tried to create an "exclusion" for that IP with the following:
object-group network nat-exclusions
network-object host 64.90.175.90
!
nat (outside,inside) source static nat-exclusions nat-exclusions
but it's not working.I also tried:
nat (outside,inside) source static nat-exclusions nat-exclusions unidirectional
Also not working.How can outside-PAT all UDP traffic excluding DNS.
I have the following setup:
ADSL ---> Cisco 877 with connected site-to-site VPN's ---> Cisco ASA 5505 with Remote VPN enabled
I want to connect my Android phone to the Cisco ASA 5505 with Remote VPN. When I forward port 500 and 4500 on the Cisco 877 to the Cisco ASA5505 I can connect with the phone.
But as expected, the site to site connections are lost because now they try to reach the ASA 5505 also.
I want to exclude the site to site external IP addresses from doing static NAT to the ASA 5505...how can I accomplish this ?
I have a number of devices such as Cisco Call Manager, or Cisco Wireless Controllers, etc that I want to remain in DCR but would like to exclude from the Config Archive process. Is there any way of excluding an individual device from this process?
View 3 Replies View RelatedI'd like to know if there is a way to exclude passed authentications for a specific username from reporting in the Authentications-TACACS and Authentications-RADIUS reports?
We have a few usernames that are used in scheduled jobs. We only need to know when they fail authentication, so we don't need to fill up the reports with every passed authentication from these accounts. Can this be done?
In earlier versions of LMS it was possible to choose i.e. the Routers category (top level) and enter a series of commands to be excluded from the comparison. In LMS 4.0.1 I experience, in several different installations, that this is not possible. It seems I can enter one exclude command beyond the defaults per category, the rest is not applied even though the feedback from the application is positive. Next time I access the Exclude Commands view, the commands I entered are gone. Is this a change of behaviour or a bug?
View 2 Replies View RelatedI'm working with Nexus 7010 - System version: 5.1(3).
For example, in the 7200 we can include or exclude an OID from the SNMP view entry using the command #snmp-server view.
How can we include or exclude an OID from the SNMP view entry in the Nexus 7010?
I have configured a SVI in my 4500 ( Sup 7-E 10GE,,,,,,and,,,,,cat4500e-universalk9.SPA.03.02.00.SG.150-2.SG.bin) switch and it is showing Down Down, because there were no active switch port in the vlan, I added one switch port to this vlan but this port also in the down state, so i added the SWITCH PORT AUTO STATE EXCLUDE command under this port, even after this also the SVI never came up, So i added one systen to the port so both the switch port and the SVI came up...So why SWITCH PORT AUTO STATE EXCLUDE command have no effect in this model of the switch..
View 4 Replies View RelatedDespite there are all devices are managed in DFM (accorduing to Collection Summary Portlet or Rediscover devices) there are no devices in the Fault Monitor with the message "No devices are available"Does it mean, we have absolutly no faults in our network or does it mean that we have a problem with DFM?
View 2 Replies View RelatedHow to find out which Fault Threshold group a specific interface belongs to.The scenario is that in Fault Manager there is an alarm for which I want to change the Threshold Setting.
Example Alarm:
Event_Description HighUtilization
Device IP x.x.x.x
Device Type Routers
Fault Last Updated At 19-Mar-2013 09:44:25
Component IF-router2.x.x/26 [Tu187] [x.x.x.x]
[Code] .....
I try run Fault monitor feature in LMS 4.0, but I got error like this picture :
View 3 Replies View RelatedI upgraded the LMS 4.0 with LMS 4.0.1 but now the events are removed of Fault View. The equipments than I am monitoring are: ME-3600, ME-3800 and ASR 9000. This is a configuration problem or I have to update something else?
View 1 Replies View RelatedI have a Sony Viao laptop with WinXp SP3 which is now 6 years old. We are currently renting a holiday home in the USA which has an unsecured network. We have two other laptops and they are connected, no problem. This morning my Sony worked fine on email and web access but I was having trouble on FTP. Then email stopped and then web.I have tried all the usual solutions. Delete the Network, restart etc etc.It clearly show the network (and also another secured network I cannot access). When I connect it shows "Acquiring network address" then just hangs. If I press, repair it hangs on "Renewing your IP address" Does the fact that it can see the networks and when I "ping 127.0.01" it seems to be OK, mean that it CANNOT be a hardware fault? I ask this partly because the WLAN switch at the front often does not seem to work (when it does work it is green and currently it IS green)
View 9 Replies View RelatedThis is Cisco Prime LMS 4.2.2 on Windows 2008 R2
As far as I understand it Fault Manager need to be able to do reverse lookup for ip adresses to show the correct name in the "device name" column. I have double and tripple checked and all devices that only is shown as an ip address do have a reverse in the dns used by the LMS server. The device is correctly registered and inventory have been run. If I hold the mouse pointer over the crosshair on the row of the offending device all info is shown including correct device name and fqdn.
The server is upgraded from 4.2.1 to 4.2.2 and we have the same problem before the upgrade.
I have an ISR 1921. Every now and then, it crashes saying "Possible software fault". The system LED flashes amber and only a hard reset (power on/off) will reload the ISR.
View 2 Replies View RelatedI am trying to setup Fault Monitoring on LMS 4.0. When I try to create a Fault Notification Group no devices are listed. They appear to be listed in all other places so I am at a loss as to explain why they are not appearing.
View 7 Replies View Relatedi´m looking for two hours now and can not find a way to suspend a device in the Fault Monitor. We´re using LMS 4.2.2
View 1 Replies View Relatedi have trying for a few days to connect my HP G7000 notebook to the internet through my wireless but i have tried everything i can think without getting anywhere. I only got it a few days back for my daughter to do her homework ect, but can't get it to connect i see a post on here about updating drivers but i can't get it to connect to do this, then thought about downloading the driver update it may need to my laptop but i really dont want to download anything onto my laptop as its a different model with different drivers and dont want it to stop my laptop working.i get on the HP G7000 is cannot communicate with primary DNS server 194.168.4.100 then underneath that message it is saying Network diagnostics pinged the remote host but did not receive a response
View 3 Replies View RelatedWe are running LMS 4.1 and we have more than 150 devices.LMS could not find the fault discovery for 3 switches with partnumber WS-C3560C-12PC-S. This switches are considered as unknown.Ios version is c3560c405-universalk9-mz.122-55.EX3.bin But other things are ok. Inventory Collection ,Config Archive, Topology Data Collection etc . Is there any way to fix ths issue? We have compact switch WS-C3560CG-8PC-S, which is working perfectly for all features.
View 4 Replies View RelatedLMS discoverd all my devices and updated the DCR. This devices are visible in DFM. For some of this devices i would like to change the threshold values. For some reason the devices are not visible in Monitor->Fault Settings->Seup->Threshold Settings (please see screenshot) Is there another approach to change the threshold values?
View 5 Replies View RelatedI've just installed LMS 4.2, like it a lot so far. In the Fault Monitor, the Device Name column shows the device's IP address rather than the host name. We need for it to show the host name, for ease of troubleshooting; most folks don't have the IP addresses memorized. Likewise, when an email is sent out for an event, the managed device field also shows up as the device's IP address.
The devices were all discovered with their IP addresses rather than a host name...should LMS have automatically found their host names? Regardless, I manually updated all of the device's host names, yet they still display as an IP address in the fault monitor.
Also, it appears I need to figure out some way to throttle alerts. One particular device will report an event (ie a temperature out of range) dozens of times in a polling period...several per second, even though it's the same alert.
I am working with LMS 4.1 and FDM 4.1.0.
If I ask to the Supported Device Finder Portlet about C4503-E (SysObjectId: 1.3.6.1.4.1.9.1.874), it tells that this device is supported by DFM 4.1.0. Nevertheless, in DFM module each one devices appear in the "All Unknown Devices" group, with Error Code: Unsupported. CDP is enable in each one of these devices.
Cisco Prime 4.2. My device is stuck in Questioned state in Fault Management. The device though can be pinged from the server. Actually, I can already manage the device and have archived its configuration. Problem is, on Fault Monitoring Device Administration, its on Questioned state even though I already tried to rediscover the device several times.Do I need to configure something on the server like put in the IP address and hostname of the device in the host file of Windows Server 2008?
View 1 Replies View RelatedI'm trying to configure Fault Tolerance on a pair of 4710s. I followed the doc, and configured int gi1/4 as the fault tolerance interface, using vlan 12. However the GUI is saying FT Vlan Down
The troubleshooting wiki said check the physical connectivity, but everything there looks good. Each ACE can ping it's own IP, but not the router on that VLAN, or the peer. They're connected to a dedicated VLAN in a switch, and I even tried a crossover cable to directly connect the two. [code]
I am running my laptop on Windows 7 Proffesional 32 bit and it won't let me search for a wireless connection on the Control Panel I think it might be a problem with the wireless switch at the bottom as it doesn't show the wireless sign on the laptop. I have also tried running the laptop on Ultimate 64 bit but the problem continued to persist.
View 12 Replies View RelatedI have a 1Gb network set up whereby I have a Netgear 26 Port 1000Mbps unmanaged network switch at the heart of my home network. What I have the problem with is devices connected on any one of my 3 300Mbps access points drop out showing no internet but they really mean no network access unless i disconnect and reconnect or switch to another access point. Other things I get happening is one min i have a transfer speed wired connection to wired connection of 35Mb per second and then I only have 8 or less. I am wondering if I have cable issues but before I went out and spent about �100 on new belkin cat6 cable I would ask if there is software I can use to test all the devices on the network so I can replace the faulty item.
View 3 Replies View RelatedRegion : UnitedArabEmirates
Model : TD-W8961ND
Hardware Version : V1
Firmware Version :
ISP :
I have two W8961ND, one for may office and the another one for use at my home, I tried to upgrade my device but during the upgrading the power supply plugged out and after that my device didn't boot up any more, so how can I repair my device, Is there any uploader for it's hardware chip because it doesn't work with it's LAN port or WIFI at this moment
have a Dell Inspiron 1525 and when I revived it from years of neglect I have come across a problem that I cannot connect to a wifi connection.I know that in order for the wifi to be found the wireless in my laptop has to be turned on, however the light on the side does not switch on.So far I have installed drivers and even bought a new wireless WLAN card...And still it does not work.The laptop runs fine with wired connection but I want to use wireless?
View 3 Replies View RelatedI am working as a Network Administrator. Here I have to manage Cisco Switches 2960 and 4500 Series, Active Directory, Database Server, Exchange Server, File Servers, IP Telophony, Fortigate Firewall, 2960 Router, Wifi availability within Company. Although, in case of any disaster we will contact to vendor for solution, but the management told me to deploy any Software/Network Monitor which will facilitate to manage all this, i.e, overall network Health check, Performance Measurement, Fault Tolerance.
View 2 Replies View RelatedI would like to know if there's a way to show Current-Utilization percentage within the messages generated by the Fault Management Module in LMS 4.0 [code] As you can see above CurrentUtilization percentage is not shown in Event Description section.
View 2 Replies View RelatedLately I encountered random Internet connection issues?My router is a Netgear Wireless ADSL Firewall Modem Router DG834 (Firmware V1.05.0) and my ISP, isn't the most reliable regarding bandwidth... All clients (max 3 at the same time) connect wireless.The problem is that the last few weeks my connections is very unstable, all clients lose the internet connection until you restart the router manually.I can't even connect to the webinterface (192.168.0.1), during the downtimes.
View 4 Replies View RelatedI am able to ping the ACS ENGINE 4.2 from any PC or device. But I am not able to ping any device from the box while logged in via SSH. while I can do so while logged in via console. Is this some kind of bug or is there any patch which after installing will allow me to ping devices from ACS SSH sessions.
View 3 Replies View RelatedIn my existing production router 7609 of my company, sup-engine already fixed in slot 5 with SRC2 12.2(33) IOS and I need to insert another sup engine in slot 6 with SRE7 IOS code image and after this, again sup engine in slot 5 must be with SRE7 IOS image...(also I have extra sup engines with SRE 7 code image ready with me) Query:i am going to offload router before proceed for this activity?i will insert new sup engine in slot 6 with SRE 7 ios image and now i need to re-install spare sup engine with SRE 7 code readily available with me by removing existing sup engine from slot 5 (Active) so what will be the proceedure to insert new sup engine with SRE 7 code in slot 5 and slot 6 with minimum downtime of router?
existing setup sup engine in slot 5 with SRC2 12.3 (old hardware) slot 6 is EMPTY
final result should be like this: sup engine in slot 6 with SRE 7 (new hardware)
sup engine in slot 5 with SRE 7 (new hardware)
