Cisco :: LMS 4.0 Fault Management Module Alert Doesn't Show Current-Utilization Percentage

Feb 22, 2012

I would like to know if there's a way to show Current-Utilization percentage within the messages generated by the Fault Management Module in LMS 4.0 [code] As you can see above CurrentUtilization percentage is not shown in Event Description section.

View 2 Replies


ADVERTISEMENT

Cisco :: LMS 4.2.1 Fault Setup Doesn't Show Any Devices

Aug 8, 2012

LMS discoverd all my devices and updated the DCR. This devices are visible in DFM. For some of this devices i would like to change the threshold values. For some reason the devices are not visible in Monitor->Fault Settings->Seup->Threshold Settings (please see screenshot) Is there another approach to change the threshold values?

View 5 Replies View Related

Cisco Switches :: SGE2000P Stack Interface Utilization Percentage?

Aug 3, 2011

I'm using a stack of four SGE2000P switches for a PoE video camera system.  I've got the cameras in a VLAN and everything's working fine. 
 
I'm wondering, though, is there a way to find out what data rate the stack interfaces are working at (since it's going over cable infrastructure we put in ourselves), and also what percentage of that bandwidth is being used?  I don't see anyway to get to those interfaces from the main page, and I wasn't able to find a way to do any sort of percentage thing even on a regular interface.

View 2 Replies View Related

Cisco :: NAM Module On 6509 Doesn't Ping Via Management Port

Apr 27, 2010

I have a cisco 6509 configured with a cisco NAM module. I have reset the config of the NAM module by the config clear command. Since this moment I can't no more ping the NAM module via the management port:  OK via the 127.0.0.91 address and log in ok via the ios cli session command. [code] I have already tried to reboot the module via the ios cli hw module command and nothing better.

View 12 Replies View Related

Cisco :: 4.2 Device Is Stuck In Questioned State In Fault Management

Jan 14, 2013

Cisco Prime 4.2. My device is stuck in Questioned state in Fault Management. The device though can be pinged from the server. Actually, I can already manage the device and have archived its configuration. Problem is, on Fault Monitoring Device Administration, its on Questioned state even though I already tried to rediscover the device several times.Do I need to configure something on the server like put in the IP address and hostname of the device in the host file of Windows Server 2008?

View 1 Replies View Related

Tool For Network Management (Health Check / Performance And Fault Tolerance)

May 2, 2012

I am working as a Network Administrator. Here I have to manage Cisco Switches 2960 and 4500 Series, Active Directory, Database Server, Exchange Server, File Servers, IP Telophony, Fortigate Firewall, 2960 Router, Wifi availability within Company. Although, in case of any disaster we will contact to vendor for solution, but the management told me to deploy any Software/Network Monitor which will facilitate to manage all this, i.e, overall network Health check, Performance Measurement, Fault Tolerance.

View 2 Replies View Related

Cisco Switching/Routing :: 3750 - Show Interface Vlan (ID) Doesn't Show In / Out Traffic Rate

Mar 13, 2013

I have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.

View 2 Replies View Related

Cisco Firewall :: 5505 - Show Current IP Address Of Interface (dhcp)

May 8, 2012

Is there any way of showing the currently assigned ip address for an interface configured to use DHCP on an ASA 5505?

View 2 Replies View Related

Linksys Wireless Router :: WRT54GC Current Time Always Show 1-Jan-2000 00:08:40?

Jul 27, 2011

how to change the time zone, the current time always show Firmware Version:1.01.6Current Time:Sat, 1-Jan-2000 00:08:40 and can't connect PPPOE

View 1 Replies View Related

Cisco Application :: CSS11503 SAM Module On 99% Utilization

Jul 27, 2012

CSS11503 that has a SAM module having a 99-100% utilization. Can this affect the services if both the accelerator module cpu peak to 99%.
 
Kindly see below logs:
 
LPHGT11# show system-resources
System Resources for 1/1:
Installed Memory:   268,435,456 (256 MB)

[Code].....

View 2 Replies View Related

Cisco :: 4500 Interfaces Utilization Over 6500NAM Module

Jan 23, 2012

I have cat4500 swtiches & need to monitor interface bandwidth utilization over NAM installed 6500 chassis. How can I monitor traffic utilization over NAM like we do in PRTG/MRTG/Cacti ?

View 0 Replies View Related

Cisco WAN :: Show All Module On ASR 1004?

Feb 14, 2012

how to show all  the module on the ASR 1004?

View 4 Replies View Related

D-Link / DCS-942L :: No Files Show Up On Card Management Screen

Feb 10, 2013

Ive formatted the sd card, enabled video/image recording, but no files show up on the sd management screen. I tried to select a folder to save the files to from the live video screen, but nothing pops up/opens when I click on the folder button. I'm using the google chrome browser w the latest java update on an xp box.

View 4 Replies View Related

Cisco Switching/Routing :: 6509 Module Results Show Pass And No Errors In The Logging

Sep 18, 2012

We have a design of two 6509 running in a VSS with dual supervisor each having fthree 10/100/1000mb etherner modules. We have diagnosed a wierd problem that none of the switchports in module 1 and 2 on either switches are having layer2/layer 3 connectivity.
 
Tried everything from changing the cables to changing the end device but no luck with it.
 
Module results show pass and no errors in the logging.

View 2 Replies View Related

Cisco WAN :: 887 Doesn't Support Show DSL Command?

Jun 26, 2011

The Cisco 887 doesn't support the show dsl command, what is the command that I need to use to display the speed my ADSL is operating at? On the Cisco 877 the command I use is show dsl int atm 0 but this doesn't work on the 887

View 4 Replies View Related

Cisco :: LMS 4.0.1 / UTLite Script Doesn't Show Username

Sep 7, 2011

I Have installed LMS 4.0.1 for my client. I have also installed UTLite script on the domain controller as per instruction from cisco. When i look at the utlite.log i'm seeing message displayed below:
 
Failed to create Tables. Transaction Rolled back
Failed to create Tables. Transaction Rolled back
: com.sybase.jdbc2.jdbc.SybSQLException: SQL Anywhere Error -110: Item 'getAuthenticatedUsers_ACS' already exists
Intializing the Controler 9 = skt Pkg = com.cisco.nm.cm.ut.ctrlplane.ctrls.SocketCtrl
2011/08/25 14:59:14 main utlite INFO SocketListener: Socket Listener : Port : 16236
Started Socket Listener

[code]....

View 2 Replies View Related

Wireless :: Connection Doesn't Show Up On Window Xp

Feb 4, 2011

Wireless connection doesnt show up on Windows Xp, I now if it connected to the internet I could just install updates and it would automatically fix it, but I cant until i get it to connect?

View 1 Replies View Related

Laptop Doesn't Show Wireless Connection

Mar 1, 2012

my laptop isn't showing my wireless internet connection in the list.But my phone is connecting to my wireless internet connection without any problem.I am using a Toshiba Satellite laptop with Windows Vista.

View 3 Replies View Related

No Internet Connectivity / PC Doesn't Show Up On Network

Jan 15, 2012

Every once in a while when logging into Windows (7 Ultimate 32 bit) My PC decides it couldn't find a network connection, usually restarting the computer solved the problem, however now I have seemed to permanently be stuck on the "identifying" stage of my LAN connection. My mobo is an Asrock p67 extreme, the network adapter is a realtek pcie family card.Now I know it is not my modem since I can connect on my other PC in the living room, I verified this with a phone call to my ISP, they couldn't see my PC connected to the network but could see the other one.It is not the Ethernet cords, I switched them and even used a new one. I tried rolling back, installing updated and installing factory drivers for my network card, no change.

I tried turning off the PC, disconnected the power cord, discharged it, left everything off/ disconnected for 30 minutes and reattached, powered on, no change.I made sure my DHCP was on and that my PC was set to automatically retrieve IP/DNS.I even bought a new Ethernet card, installed it and I still can't connect, so its not the realtek card.I can't even access my modem using its UP address, 192.168.2.1 (Bell 2wire) but I can on my 2nd PC, it sees all other devices, PS3 /Smartphones but not my PC.

View 19 Replies View Related

Laptop Doesn't Show Any Wireless Signals

Nov 4, 2011

i have a packard bell network.i formatted the whole laptop.and now my laptop doesnot show any wireless network,however connects to dial up connection.i am using windows 7 ultimate 32 bit os

View 1 Replies View Related

Connect To Doesn't Show Wireless Networks

Apr 27, 2011

I am trying to connect to a different network, but for some reason when I click "Connect To", where it tells me to click to join another wireless network, it just shows me this: and does not show me the Wireless Networks that are available (I am not sure what it is called)

View 6 Replies View Related

Laptop Doesn't Show Any Wireless Networks

Jan 13, 2013

So, I happened to do CD recovery a day ago; *Due to forgetting Administrator password* and now my laptop seems to not be able to pick up any wireless connections when there usually is a ton. Also every time my laptop restarts it always loads saying "Preparing for first time use" Like I used the CD recovery again. which I didn't. I thought that maybe it has to do with the Drivers and such, though im not very tech fancy, so I wouldn't exactly know where to find the correct driver to install, and which to install.[code] Oh and lastly, I happened to notice on Driver manager, that on "other devices" there is a yellow exclamation point, on both of them: Intel(R) Centrino(R) Wireless-N + WiMAX 6150 and Network Controller.

View 1 Replies View Related

D-Link DIR-825 :: 5 Ghz Enabled Doesn't Show Up When Scanning?

Dec 15, 2010

I am running a DIR-825 I believe one of the original's no updates or anything.  I run it mixed mode.  The 2.4 shows up and I can connect to but the 5 ghz (n) speed says it's enabled but I can never see it when I scan on any of my wireless n products (laptops and other computers).  Dlink support told me to change to mixed mode g and n.  I was running it in mixed mode (a, g and n).  D link told me to change to mixed mode g and n and to make sure they stay on channel 6 and 11.  Is this correct.  Which firmware should I upgrade to and is there any easy way to do this?

View 4 Replies View Related

Cisco Firewall :: 5585 - BVI Doesn't Show Up In Multi Context ASA

May 7, 2013

I have an ASA 5585 in transparent mode, multi-context. It seems that the option to configure a BVI in one of the traffic contexts isn't there. In other words, while I see the option to configure a bridge group interface in the admin context, no such option comes up in the traffic context.
[CODE]....

View 1 Replies View Related

Cisco Wireless :: Lwapp 1242ag Doesn't Show Mesh

Oct 10, 2011

I'm using a wlan controller with 1242ag converted to lwapp, i'm trying to enable 5.8 but when i change the from local to bridge the lwapp disappear from controller. May be that the firmware does not support mesh !I'm following the 4402 wlan manual at page 641.

View 5 Replies View Related

Wireless :: Laptop Doesn't Show Wifi Connection

Mar 25, 2011

With ibm z60m laptop i want to connect wi-fi internet modem but laptop does not show wi-fi connection

View 1 Replies View Related

Scanner Doesn't Show Up At All In Local Network Devices

Nov 12, 2011

Im working for a client at the moment and I've had to setup a network printer for them, I've got 4 Windows 7 machines easily printing over the network to this printer that is connected wirelessly but they want one of there machines to use the scanning functionality of the printer.The scanner doesn't show up at all in the local network devices like the printer does and to be honest i don't really have any experience with scanning over a network to a windows 7 machine, but this printer does support scan to ftp so my idea is to setup a small ftp server on the windows 7 machine with a folder to stored scans on the desktop or something, then put the details of the server in to the printer making it as easy as possible for the customer to scan stuff and just get it from the folder on the desktop, i could also share this folder over the network for anyone to open and get a scan if needs be.

View 2 Replies View Related

New NIC Doesn't Show Up In Network Connections Or Device Manager?

Jan 20, 2011

I put Win7 on a customed pc bought online. The motherboard has an Atheros L1 integrated NIC and I installed a Dlink dge530t NIC into a PCI slot. I know I have to disable the onboard nic but the installed card is not comming up either in Device manager or network connections. What gives? In the bios under integrated peripherals i did enable PnP OS.

View 4 Replies View Related

HP Laserjet 4050n Doesn't Show Up As Wireless Device?

Feb 1, 2013

I'm trying to connect an HP Laserjet 4050n to my wireless network but it isn't finding it? I've tried disabling firewalls etc and still no luck.

View 1 Replies View Related

3389 Windows 7 RDP Is Enabled But Doesn't Show Up In Net-stat

Jun 4, 2013

I've enabled RDP on a laptop, but I can't connect to it. Pinging the laptop works. nmap shows ports open, but not RDP. netstat on the laptop shows nothing listening on 3389. I've also tried rebooting. [code]

View 1 Replies View Related

Cisco Wireless :: AP1602 Show Run Output Doesn't List Various SSID That Are In Use

Mar 7, 2013

How to approach an overnight upgrade from autonomous AP1231/1242 deployment into a 2504 controller-based AP1602 deployment.I do not have access to the existing 1231/1242 deployment ==> I need to ask network manager for all necessary config info to be ported onto the 2504.Example: the 1231 show run output does not list the various SSID that are in use.Therefore the question is: which commands' output do I need to ask to have all possible config data from 1231/1242 to use when configuring the 2504/1602 deployment.

View 2 Replies View Related

Cisco Switching/Routing :: 3750 Switch Doesn't Show Text

Apr 26, 2013

I am working with 3750 switch.I console the switch and turn it on and it doesn’t show text in hyper terminal with any BAUD (I tried all the speeds).  The hyper terminal works with other switches so the problem is not with the hyper terminal.when I tried to break the password it stuck after I was writing "flash_init" and when I entered or typed text it show only garbage characters. I tried to break the password with all the speeds and it shows garbage output. I tried to turn on the switch and hold control + break and it showed the text only with the speed 115200, but after I left holding and tried to type it showed only garbage again. Also I tried to copy text from the notepad to the hyper terminal.

View 6 Replies View Related

Cisco :: LMS 4.0 Doesn't Show The View Image For LAN WS-C3750X-48T-L In Stack Mode?

Aug 19, 2011

I downloaded all updates packages of the device for the Cisco View and I could not the show the image

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved