I have cat4500 swtiches & need to monitor interface bandwidth utilization over NAM installed 6500 chassis. How can I monitor traffic utilization over NAM like we do in PRTG/MRTG/Cacti ?
View 0 RepliesWe have a Switch Catalyst 4500, model WS-C4510R+E, with 2 Supervisors, models V-10GE, which is showing high CPU values all times.When this occures, the switch shows 95-100% for total cpu for a few hours at a time.show proccesses cpu shows process Cat4k Mgmt LoPri with an unusual cpu value of 56% The show platform heath command gave me a high reading for K2L2 Address Table R which is curently 9,45% but the last hour is around a 20% average CPU ?[URL] what the process K2L2 Address Table R means and what could be the cause of this peak?
View 3 Replies View RelatedCSS11503 that has a SAM module having a 99-100% utilization. Can this affect the services if both the accelerator module cpu peak to 99%.
Kindly see below logs:
LPHGT11# show system-resources
System Resources for 1/1:
Installed Memory: 268,435,456 (256 MB)
[Code].....
Im wanting to add an additional module in to my Cisco 4500. Is as simple as plug and play or is there some commands that I need to add or anything I should be aware of.
View 2 Replies View RelatedWe inserted a new module with 48 rj45 ports in a 4500 with just one supervisor module. We have two 4500, and we tried the new model in the other 4500 and it´s working properly and giving a OK status. Furthermore, the module´s LED status is green. We saw that there are 8 ports (from 17 to 24) that are in faulty state, so probably this is the cause for the faulty state for the module.
We tried already a Hw reset, replace/insert again the module...
We are almost sure that it can be a Hw failure. We are getting the following results different commands:
show module :
Mod Ports Card Type Model Serial No.
7 48 10/100/1000BaseT (RJ45) WS-X4548-GB-RJ45 JAXXXXXXXH
M MAC addresses Hw Fw Sw Status
[Code].....
We have recently purchased a Cisco 4506 that has several Gigabit Ethernet modules installed.One of the Ethernet Gigabit modules - a WS-X4424-GB-RJ45 - is being picky with who it talks to at Gigabit Ethernet.
If I plug a laptop into one of it's RJ45 ports using a Cat 6 cable, nothing happens. No link light, no notification of link up or down on port statistics, absolutely nothing.If I plug a server into the same port it works fine at Gigabit Ethernet (even using the same Cat 6 cable).I can get the module to recognize a laptop if I fix the speed/duplex on the laptop to 100Mb/Full. I have tried this with other staff laptops from different vendors (HP / Dell / etc.) all with the same result.
The module directly underneath this module - a WS-X4448-GB-RJ45 - works fine for both laptops and servers. We have tried swapping the module positions but to no avail.
I am using Cisco ASA5510 Firewall in my network. Upgraded the Memory and Flash to 1GB and 512MB.But the 5 interfaces ports are 10mbps.Can it possible to upgrade the module of Interfaceses from 10mb to 1gb?
View 2 Replies View RelatedI would like to know if there's a way to show Current-Utilization percentage within the messages generated by the Fault Management Module in LMS 4.0 [code] As you can see above CurrentUtilization percentage is not shown in Event Description section.
View 2 Replies View Relatedswitch catalyst 4500 with ios cat4500e-universal.SPA.03.02.00.XO.150-2.XO.bin. I need to configure modules 3 and 4 of supervision, the problem is that I need the 4-port module 3 are active but only the first turn on both the module 3 and the first port on the module 4. [code]
View 1 Replies View RelatedI am trying to add WCCP to be configured for websense. My first option seems to be either purchase an IPServices license for the stack of 3750E switches, but i am thinking this will require us to license all three switches in the stack. The second option i am looking at is to do the WCCP configuration on the 2800 router we have on the edge. The problem is both Gig ports are in use, one going to the firewall and the second going to the ISP. My first question would be, which option is better in terms of manging as well as cost of implementing it.The second question is, if WCCP on the router is a better option, what is the add on module i should be looking to get to add the additional ports to hook up the Websense cache.
View 8 Replies View RelatedI haven't covered this bit in my CCDA studies (yet) but I was thinking, what do people consider too much CPU utilization for:-
A) A switch during normal working hours? (Layer 2 Switch)
B) A Router during normal working hours?
I was thinking a normal level for a switch would be at max 10% and I would get worried at 50-60% if this lasted for several minutes at a time.For a Router I would expect higher utilization in general so I would think up to about 25% during normal usage and at worst case a prolonged period the same as the switch.This isn't something I see discussed very often, except maybe by me when a router goes mental and maxes out at 100%.
I have a Cisco 7506 end cpu utilization from my VIP 0 is going to 100%. The biggest traffic from my interface is aroud 100 Mbps and my bandwdth is 1000Mbps. Who know what could happend?
64556445650707820870990195455665559401024909987026556445558100 * 90 * 80 * * 70 * * 60 * * 50 * * 40 **** * 30 ******#* * 20 #######** * 10 * *** ******************* **********##########****** **** 0....5....1....1....2....2....3....3....4....4....5....5....6....6....7. 0 5 0 5 0 5 0 5 0 5 0 5 0 CPU% per hour (last 72 hours) * = maximum CPU% # = average CPU%
We have CPU reports set to run daily for some of our higher priority switches, and we've noticed that some of the data isn't meshing with what we see on the switch. We have one heavily utilized switch that reports near 100% CPU utilization sometimes. I can do a "show proc cpu history" on that switch and see that at least once an hour over 72 hours, we'll see a near 100% CPU utilization.
The problem is that these spikes never appeare on any of our reports. We'd like to see this info because even if the switch spikes for just a few seconds or a minute, it could still indicate that we may have issues. Without that in the report, we may never realize there could be a problem.
Is there a way for this info to show in the report? I'm under the impression that if LMS polls the switch and doesn't see a high utilization average, then maybe it doesnt' enter that in the report. I guess I'd just like to know how often it pulls this data, and how it decides wath the Min, Max, and Averages are.
how do i know someone is connected to my wireless
View 1 Replies View RelatedWe are currently running ACS 5.4.0.46.0a in a VMWare environement. We have 1 Primary and 1 Secondary running on our ESXi 5.0 cluster at our HQ and 1 secondary running on a standalone ESXi 5.0 at our DR site. All three instances were created at the same time and configure identical. The only difference being the physical box they are running from and that the secondary running on the ESXi cluster is the log collector. We are in the process of migrating from ACS 4.2 and only have 3 systems that authenticate to the new ACS 5.4 servers. Those systems are hardly ever used so there may be only 1 or 2 authenticates a day.
My concern is that the primary is running at around 30% cpu utilization constantly, and the secondaries are running at around 1%. Why the primary would be running the cpu that high when it should be pretty much idle most of the time? Or, how can I find out what process is running the cpu that high ?
We have configured 20 route in ASA 5520. The CPU usage goes to 100 % at the moment when we add a specific route.route inside 10.254.101.0 255. 255. 255.0 10.254.102.254 1.This is the same case when we add this route at the first cli or as the 10th cli or the 21 cli (errespective of the position of cli) There is an another route out of which 20 routes we have configured is route inside 10.254.103.0 255.255.255.0 10.254.102.254 1.The normal case if we dont add the problamatic route , then the CPU utilization is only 2 %.
View 1 Replies View RelatedI have 3845 router where 200 branches are connect. Ho have database server where branch are synch interval period.some of days observation cpu load average 70 % and sometimes it reaches 100 %.yesterday when I give command clear arp then instant cpu load reduce and 20 % yesterday cpu load 12-20 %. Today morning when I give command Cpu proc history then I found cpu load 60 % and at night it was 3 times reaches 100 %. so my question is after clear arp command at least 10 hours cpu utilization 20 % but after that it increase.so for any LAN broadcast it happend ? how i understand cpu high for Broadcasting or anything else.
View 2 Replies View RelatedWhat causes LMS 4.1 to have high memory utilization?
View 4 Replies View RelatedOur Router 7606 is in a problem with high CPU Utilization. We are using one EBGP and one IBGP session. We are also running OSPF with area 0 between two IBGP router to exchange few local networks. When bandwidth cross 100 MB than only CPU use become 100%. when bandwidth consumption is 80MB CPU use become 80% end so on.
Out put is when bandwidth consumption is 34MB
CPU utilization for five seconds: 44%/43%; one minute: 42%; five minutes: 30%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
78 44 9625 4 0.39% 0.03% 0.00% 2 Virtual Exec
13 40 375 106 0.07% 0.00% 0.00% 0 ARP Input
30 116 1098 105 0.07% 0.01% 0.00% 0 IPC Seat Manager
[code]....
I have a hight CPU utilisation problem in my CISCO7609-S routers. the cpu utilisation can rise 99% et this is usually. In the moment of hight CPU the the process CPU give the following:
the show processe cpu history give: show version
I have a 2811 that is really hitting the CPU hard. Nothing shows on CPU processes. It has an IPsec VPN tunnel back to HQ which also has a 2811 that terminates the VPN. The HQ has 2-3 IPsec tunnels to other remote sites. The CPU at the HQ avg 50% utilization during business hrs, peaks at about 80%. The remote one is very high 95% peaks, avg 80%-95% during business hours with bandwidth utilization of only 10-20Mbps. I read somewhere that its possible that fragmentation could be causing this. My question is, if I set the MTU to 1450 on the remote, I am guessing I will need to do all the other routers as well, the HQ and other remote sites? Siince they use the same outside interface to my HQ, is that correct?
View 3 Replies View RelatedWe have Cisco 2811 router and facing high CPU utilisation as 70%/67%;,IOS Runing :c2800nm-advsecurityk9-mz.124-3f.bin.
View 4 Replies View RelatedI am not sure if the issue I have is due to router's performance of my configuration. Currently I have 2621XM connected in my internal network where Fa0/1 is considered untrusted zone and Fa0/0 is considered trusted. It appears that traffic is limited to about 3.17MBps (Mega Bytes) between Fa0/0 and Fa0/1. There are ACLs on the Fa0/1 inbound and Fa0/0 inbound. I am also using ip inspect rules for the Fa0/1 outbound traffic. When I remove ip inspect policy from the Fa0/1 interface, the traffic speed bumps up to about 4.8MBps (which is about 38Mbps - Mega bits).
Each time the CPU utilization is: CPU utilization for five seconds: 99%/99%; one minute: 19%; five minutes: 4% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
Access to the router during that time is veerrrryyyyyy slow! Does this mean I am hitting the maximum limit this router can handle?
High cpu utilization on cisco 7206 vxr router.[code]
View 2 Replies View RelatedWe are finally installing 5508 controllers at multiple sites. (Yaaaay) We have an existing SNMP mangement system (Zenoss) that will work fine with these 5508's if I can figure out which OIDs report things like CPU utilization, free mem, temp, number of clients etc. We already have modeler plugins that list the number of APs managed and will also show the wired interface stats. Attached are two files with the resutls of snmpwalk. One has the raw OIDs, the other has the OIDs with the symbolic prefixes.
Most of that I'm looking for seems to be missing. For example, in other Cisco forum posts, it was mentioned that CPU utilization was available via this OID:
agentCurrentCPUUtilization ......OID: 1.3.6.1.4.1.14179.1.1.5.1
[URL]
and, Free Mem was available here:
agentFreeMemory free RAM of in Kbytes ....OID: 1.3.6.1.4.1.14179.1.1.5.3
Problem is, none of those OIDs are returned when I walk the 5508. For example:
[ZenStatus]$ snmpwalk -Ofn -v2c -c M31eRt4 10.254.248.3 | grep -F "1.3.6.1.4.1.14179"
[ZenStatus]$
(nothing even close to the agentCurrentCPUUtilization OID is found)We are currently running 7.0.235.0 .
We have a VPN concentartor which is having few VPN and doing NAT (Static and PAT) as well. One of our customer has added huge number of serves so we have to do hundreds of static and PAT rules.we have really large number of customers which are growing and do so the NAT in VPN concentartor.
I am bit concern and want to know what will be the best way to check that how my VPN concentartor is doing .As we all know its a GUI i try to check few stuff but couldnt get any info.... the model number is 3015.
I am observing very high CPU utilization on my Cisco 7206VXR (NPE-G1) Router. We have done all the necessary troubleshooting but not able to identify root cause. [code]
View 10 Replies View RelatedI am running Cisco Prime 4.2(UNIX version) on a VM. CPU utilization will run between 90 and 100% constantly. Reloading the server will stabilize the CPU for a short period of time, however the CPU usage will always return to 90-100% utilization. Currently I have about 130 devices added to the system.
View 1 Replies View Relatedwe have 2 Cisco C4507 Switches working As Core Layer, but the CPU Utilization is about 54% most of the time and sometimes it goes up to 70% or 80% also.
which services are causing this utilization. [code]
we have cisco 4510+R switch with Cisco IOS-XE software & we are facing high cpu utilization on core 1 (95%) & on core 0 (15%) since last 2 hours.
I have taken logg file but did not understand how to analyzed it & where is problem. log file is attached.
I've deployed many Cisco PIX 501 v6.3.3 either as normal firewalling feature and/or with VPN features enabled. I noticed in all my deployments, regardless if it's during peak hours or after office hours, the memory utilization is always consistent 11MB utilized over the total of 16MB(memory default size).
View 3 Replies View RelatedLMS is not reporting on all of my interfaces, utilization in particular. As an example, I have 1 location that is connected via DMVPN tunnels, when I run a utilization report, it only comes back with information for 1 interface, a random interface, port FA 1/7 on the switch module. If it was all of the switchports it might make more sense.
In DFM device detail the interfaces are being managed.
In the Link Utilization Poller, only 1 interface is listed (FA 1/7).
In Cisco 7206 VXR (NPE-G2) router , the CPU utilization is at an 80-90% always , but none of the process is consuming not more than 1%. In the show stacks output we are observing network interface interrupt is called very frequently. so what does network interface interrupt is about. Logs for the reference: show process CPU sorted
CPU utilization for five seconds: 88%/88%; one minute: 89%; five minutes: 89%
PID Runtime(uS) Invoked u Secs 5Sec 1Min 5Min TTY Process
1 0 72 0 0.00% 0.00% 0.00% 0 Chunk Manager
2 20020000 17159 1166 0.00% 0.02% 0.01% 0 Load Meter
[Code]...