Cisco :: 5508 WLC - Getting MIB / OIDs For CPU Utilization?
Jun 24, 2012
We are finally installing 5508 controllers at multiple sites. (Yaaaay) We have an existing SNMP mangement system (Zenoss) that will work fine with these 5508's if I can figure out which OIDs report things like CPU utilization, free mem, temp, number of clients etc. We already have modeler plugins that list the number of APs managed and will also show the wired interface stats. Attached are two files with the resutls of snmpwalk. One has the raw OIDs, the other has the OIDs with the symbolic prefixes.
Most of that I'm looking for seems to be missing. For example, in other Cisco forum posts, it was mentioned that CPU utilization was available via this OID:
We are trying to monitor two stacks of CISCO WS-c3750X running IOS 12.2.(58)SE.
We can get the state of the power supplies, but after a power cycle or reboot of the switches the identifier of ONE of the Power supplies ALWAYS change. The OIDs for the rest of the PS do not vary. The problem happens in the two stacks.
I would like to get CbQos on a Cisco ASR 1002S (IOS-XE Software (PPC_LINUX_IOSD-IPBASEK9-M), Version 15.1(1)S1). With the standard OIDs (cbQosIfIndex - 1.3.6.1.4.1.9.9.166.1.1.1.1.4).
I'm setting up a Network Monitoring System in Nagios and Nagvis. Now, I want to monitor the cpu and memory of the switches SGE2000 and SGE2010 with SNMP. Does the OID for the switches SGE2000 and SGE2010 (CPU and Memory).I can't not seem to find them on the Internet(searched for hours).
What is the correct way to create an SNMP user on a Nexus 5k Switches and limit the read/write access to some OIDs?I have been searching for hours for configuration examples or guides, but i had no luck.I guess a role has to be created, containing rules for some feature, but the list of features doesn't contain anything about snmp.This is my configuration on catalyst switches and i'd like to achieve the same result on the Nexus 5k:
conf term access-list 10 permit host x.x.x.x access-list 10 deny any snmp-server view myview ccCopyTable included snmp-server group mygroup v3 priv read myview write myview access 10 snmp-server user myuser mygroup v3 auth md5 xxxxxx priv aes 256 xxxxxx end
I have a question about SNMP OIDs for the command "show counters interface intx/y delta" on Catalyst6500. The customer wants to create graphs for the following values:Overruns, qos0Outlost, InErrors, OutErrors, InDiscards, OutDiscards etc..Is possible to get these values using SNMP?
I haven't covered this bit in my CCDA studies (yet) but I was thinking, what do people consider too much CPU utilization for:-
A) A switch during normal working hours? (Layer 2 Switch)
B) A Router during normal working hours?
I was thinking a normal level for a switch would be at max 10% and I would get worried at 50-60% if this lasted for several minutes at a time.For a Router I would expect higher utilization in general so I would think up to about 25% during normal usage and at worst case a prolonged period the same as the switch.This isn't something I see discussed very often, except maybe by me when a router goes mental and maxes out at 100%.
I have a Cisco 7506 end cpu utilization from my VIP 0 is going to 100%. The biggest traffic from my interface is aroud 100 Mbps and my bandwdth is 1000Mbps. Who know what could happend?
We have CPU reports set to run daily for some of our higher priority switches, and we've noticed that some of the data isn't meshing with what we see on the switch. We have one heavily utilized switch that reports near 100% CPU utilization sometimes. I can do a "show proc cpu history" on that switch and see that at least once an hour over 72 hours, we'll see a near 100% CPU utilization.
The problem is that these spikes never appeare on any of our reports. We'd like to see this info because even if the switch spikes for just a few seconds or a minute, it could still indicate that we may have issues. Without that in the report, we may never realize there could be a problem.
Is there a way for this info to show in the report? I'm under the impression that if LMS polls the switch and doesn't see a high utilization average, then maybe it doesnt' enter that in the report. I guess I'd just like to know how often it pulls this data, and how it decides wath the Min, Max, and Averages are.
We are currently running ACS 5.4.0.46.0a in a VMWare environement. We have 1 Primary and 1 Secondary running on our ESXi 5.0 cluster at our HQ and 1 secondary running on a standalone ESXi 5.0 at our DR site. All three instances were created at the same time and configure identical. The only difference being the physical box they are running from and that the secondary running on the ESXi cluster is the log collector. We are in the process of migrating from ACS 4.2 and only have 3 systems that authenticate to the new ACS 5.4 servers. Those systems are hardly ever used so there may be only 1 or 2 authenticates a day.
My concern is that the primary is running at around 30% cpu utilization constantly, and the secondaries are running at around 1%. Why the primary would be running the cpu that high when it should be pretty much idle most of the time? Or, how can I find out what process is running the cpu that high ?
We have configured 20 route in ASA 5520. The CPU usage goes to 100 % at the moment when we add a specific route.route inside 10.254.101.0 255. 255. 255.0 10.254.102.254 1.This is the same case when we add this route at the first cli or as the 10th cli or the 21 cli (errespective of the position of cli) There is an another route out of which 20 routes we have configured is route inside 10.254.103.0 255.255.255.0 10.254.102.254 1.The normal case if we dont add the problamatic route , then the CPU utilization is only 2 %.
I have 3845 router where 200 branches are connect. Ho have database server where branch are synch interval period.some of days observation cpu load average 70 % and sometimes it reaches 100 %.yesterday when I give command clear arp then instant cpu load reduce and 20 % yesterday cpu load 12-20 %. Today morning when I give command Cpu proc history then I found cpu load 60 % and at night it was 3 times reaches 100 %. so my question is after clear arp command at least 10 hours cpu utilization 20 % but after that it increase.so for any LAN broadcast it happend ? how i understand cpu high for Broadcasting or anything else.
Our Router 7606 is in a problem with high CPU Utilization. We are using one EBGP and one IBGP session. We are also running OSPF with area 0 between two IBGP router to exchange few local networks. When bandwidth cross 100 MB than only CPU use become 100%. when bandwidth consumption is 80MB CPU use become 80% end so on.
Out put is when bandwidth consumption is 34MB
CPU utilization for five seconds: 44%/43%; one minute: 42%; five minutes: 30% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 78 44 9625 4 0.39% 0.03% 0.00% 2 Virtual Exec 13 40 375 106 0.07% 0.00% 0.00% 0 ARP Input 30 116 1098 105 0.07% 0.01% 0.00% 0 IPC Seat Manager
I have a hight CPU utilisation problem in my CISCO7609-S routers. the cpu utilisation can rise 99% et this is usually. In the moment of hight CPU the the process CPU give the following:
I have a 2811 that is really hitting the CPU hard. Nothing shows on CPU processes. It has an IPsec VPN tunnel back to HQ which also has a 2811 that terminates the VPN. The HQ has 2-3 IPsec tunnels to other remote sites. The CPU at the HQ avg 50% utilization during business hrs, peaks at about 80%. The remote one is very high 95% peaks, avg 80%-95% during business hours with bandwidth utilization of only 10-20Mbps. I read somewhere that its possible that fragmentation could be causing this. My question is, if I set the MTU to 1450 on the remote, I am guessing I will need to do all the other routers as well, the HQ and other remote sites? Siince they use the same outside interface to my HQ, is that correct?
I am not sure if the issue I have is due to router's performance of my configuration. Currently I have 2621XM connected in my internal network where Fa0/1 is considered untrusted zone and Fa0/0 is considered trusted. It appears that traffic is limited to about 3.17MBps (Mega Bytes) between Fa0/0 and Fa0/1. There are ACLs on the Fa0/1 inbound and Fa0/0 inbound. I am also using ip inspect rules for the Fa0/1 outbound traffic. When I remove ip inspect policy from the Fa0/1 interface, the traffic speed bumps up to about 4.8MBps (which is about 38Mbps - Mega bits).
Each time the CPU utilization is: CPU utilization for five seconds: 99%/99%; one minute: 19%; five minutes: 4% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
Access to the router during that time is veerrrryyyyyy slow! Does this mean I am hitting the maximum limit this router can handle?
We have a VPN concentartor which is having few VPN and doing NAT (Static and PAT) as well. One of our customer has added huge number of serves so we have to do hundreds of static and PAT rules.we have really large number of customers which are growing and do so the NAT in VPN concentartor.
I am bit concern and want to know what will be the best way to check that how my VPN concentartor is doing .As we all know its a GUI i try to check few stuff but couldnt get any info.... the model number is 3015.
I am observing very high CPU utilization on my Cisco 7206VXR (NPE-G1) Router. We have done all the necessary troubleshooting but not able to identify root cause. [code]
I am running Cisco Prime 4.2(UNIX version) on a VM. CPU utilization will run between 90 and 100% constantly. Reloading the server will stabilize the CPU for a short period of time, however the CPU usage will always return to 90-100% utilization. Currently I have about 130 devices added to the system.
we have 2 Cisco C4507 Switches working As Core Layer, but the CPU Utilization is about 54% most of the time and sometimes it goes up to 70% or 80% also.
which services are causing this utilization. [code]
I've deployed many Cisco PIX 501 v6.3.3 either as normal firewalling feature and/or with VPN features enabled. I noticed in all my deployments, regardless if it's during peak hours or after office hours, the memory utilization is always consistent 11MB utilized over the total of 16MB(memory default size).
LMS is not reporting on all of my interfaces, utilization in particular. As an example, I have 1 location that is connected via DMVPN tunnels, when I run a utilization report, it only comes back with information for 1 interface, a random interface, port FA 1/7 on the switch module. If it was all of the switchports it might make more sense.
In DFM device detail the interfaces are being managed.
In the Link Utilization Poller, only 1 interface is listed (FA 1/7).
In Cisco 7206 VXR (NPE-G2) router , the CPU utilization is at an 80-90% always , but none of the process is consuming not more than 1%. In the show stacks output we are observing network interface interrupt is called very frequently. so what does network interface interrupt is about. Logs for the reference: show process CPU sorted
CPU utilization for five seconds: 88%/88%; one minute: 89%; five minutes: 89% PID Runtime(uS) Invoked u Secs 5Sec 1Min 5Min TTY Process 1 0 72 0 0.00% 0.00% 0.00% 0 Chunk Manager 2 20020000 17159 1166 0.00% 0.02% 0.01% 0 Load Meter [Code]...
I would like to know if there is a way to monitor which programs/processes are using my network, say if there's something in the background updating that I can close to reduce lag in games, my computer is free of viruses and most the auto updates are turned off because I update them manually, so I just would like a simple straightforward answer,what program or process is using my network?
I am working as net admin which is i need to monitoring and manage my workplace network( education center )I got a few question about network traffic flow. Here is the issued.I got high bandwidth utilization so high after office hours which is only on night. as we know, after office hours there is no person at the office but the traffic flow on bandwidth utilization is high.what are the possibilities of this issued?
How to find bandwidth utlization and who consumed bandwidth lot.? Basically ,I would use speedtest.net for speedtest and will ask from ISP for bandwidth utilization.
Is there any way that to measure bandwidth utilization and who consumed lot based on IPaddress?
