Cisco Switching/Routing :: To Get CbQos On Asr 1002s With Standard OIDs
Jul 3, 2012
I would like to get CbQos on a Cisco ASR 1002S (IOS-XE Software (PPC_LINUX_IOSD-IPBASEK9-M), Version 15.1(1)S1). With the standard OIDs (cbQosIfIndex - 1.3.6.1.4.1.9.9.166.1.1.1.1.4).
View 3 Replies
ADVERTISEMENT
Jan 22, 2012
I haven't got time to test different configurations yet. Just want to quickly ask here about the fall-over route-map configuration. I saw lots of example using pip prefix-list to specify the next-hop for tracking. Is that the only way you can do it? Can you just use a standard ACL to specify that host like permit host 10.2.2.2? ip prefix-list will do like ip prefix-list seq 5 permit 10.2.2.2/32. And you apply the prefix-list to route-map then. ACL will work?
View 2 Replies
View Related
Sep 3, 2012
Checking the logs we have seen the following messages:
%SPANTREE-3-PRESTD_NEIGH: pre-standard MST interaction not configured (Port-channel3). Please, configure: 'spanning-tree mst pre-standard' on ports connected to MST pre-standard switches.
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/1, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/0/1, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Port-channel3, changed state to down
%LINK-3-UPDOWN: Interface Port-channel3, changed state to down
%LINK-3-UPDOWN: Interface GigabitEthernet1/0/1, changed state to down
%LINK-3-UPDOWN: Interface GigabitEthernet2/0/1, changed state to down
When this happened, the interface that was actually blocked by STP didn't come to forwarding state, and as a result this switch became isolated.This switch is connected to a switch that runs standard MST, and to some switches that run PVST but have bpdufilter enabled as we don't want them to participate on the STP. It is a 3750 switch with software version 12.2(55)SE5.
As far as I knew, when a MST pre-standard BPDU was received, the interface was able to receive more pre-standard BPDUs, but I didn't know it would turn the link down. Why the links went down, and if there is any way we can configure those links to accept only MST standard BPDUs.
I would also like to know if there is any chance a switch running PVST can send a MST pre-standard BPDU if it has a software version 12.2(25)SEE3.
View 5 Replies
View Related
Apr 11, 2012
Is it possible to create a vlan on a standard 3925? We have no addon cards installed.
View 3 Replies
View Related
Mar 21, 2013
I have a Catalyst 2960-S switch and a pre-standard IP Phone (Cisco 7960). When I connect the phone to the switch the switch recognizes the phone and supplies power. I would like to prevent this behaviour. ie. I would like to disable detection of pre-standard equipment. Is there a command I can issue on the 2960-S to do this? For example, on a switch from a different vendor I can issue the command: no power pre-std-detect to prevent it from detecting the 7960 phone, is there an equivalent command on the Catalyst 2960-S ?
View 3 Replies
View Related
Nov 15, 2011
I'm looking at provisioning a Catalyst 4500 with a WS-X4712-SFP+E module to allow for future 10Gb connectivity via 10Gb SFP+ interfaces. These cards are backwards compatible with standard 1Gb SFP interfaces but I'm wondering about the other way around; ie. can you populate these blades with 10Gb SFP+ interfaces when they connect to Catalysts with only 1Gb SFP interfaces at the other end?
The data sheets don't really explain this. It seems pointless getting 10Gb SFP+ interfaces for the 4500 when it's only 1Gb at the access layer end, but these access switches will be replaced in the near future (~12 months) and if the 10Gb SFP+ interfaces support connections at 1Gb speeds upfront, it would mean I could retain these interfaces when the access switches upgrade to 10Gb connectivity capabilities down the track. Does the 10Gb SFP+ interfaces are compatible with 1Gb SFP's or only other 10Gb SFP+ interfaces?
View 5 Replies
View Related
Jun 14, 2012
I have a customer with Cisco 7940 and 7960 IP phones that they do not plan to replace. They do want a new LAN and are looking at the Catalyst WS-C2960S-48FPD-L and WS-C2960S-24PD-L as access layer devices.
these switches support the Cisco pre-standard PoE required by the 7940 and 7960 IP phones.
View 5 Replies
View Related
Jun 24, 2012
We are finally installing 5508 controllers at multiple sites. (Yaaaay) We have an existing SNMP mangement system (Zenoss) that will work fine with these 5508's if I can figure out which OIDs report things like CPU utilization, free mem, temp, number of clients etc. We already have modeler plugins that list the number of APs managed and will also show the wired interface stats. Attached are two files with the resutls of snmpwalk. One has the raw OIDs, the other has the OIDs with the symbolic prefixes.
Most of that I'm looking for seems to be missing. For example, in other Cisco forum posts, it was mentioned that CPU utilization was available via this OID:
agentCurrentCPUUtilization ......OID: 1.3.6.1.4.1.14179.1.1.5.1
[URL]
and, Free Mem was available here:
agentFreeMemory free RAM of in Kbytes ....OID: 1.3.6.1.4.1.14179.1.1.5.3
Problem is, none of those OIDs are returned when I walk the 5508. For example:
[ZenStatus]$ snmpwalk -Ofn -v2c -c M31eRt4 10.254.248.3 | grep -F "1.3.6.1.4.1.14179"
[ZenStatus]$
(nothing even close to the agentCurrentCPUUtilization OID is found)We are currently running 7.0.235.0 .
View 8 Replies
View Related
Oct 8, 2012
We are trying to monitor two stacks of CISCO WS-c3750X running IOS 12.2.(58)SE.
We can get the state of the power supplies, but after a power cycle or reboot of the switches the identifier of ONE of the Power supplies ALWAYS change. The OIDs for the rest of the PS do not vary. The problem happens in the two stacks.
View 6 Replies
View Related
Nov 7, 2012
I'm setting up a Network Monitoring System in Nagios and Nagvis. Now, I want to monitor the cpu and memory of the switches SGE2000 and SGE2010 with SNMP. Does the OID for the switches SGE2000 and SGE2010 (CPU and Memory).I can't not seem to find them on the Internet(searched for hours).
View 1 Replies
View Related
Dec 12, 2011
What is the correct way to create an SNMP user on a Nexus 5k Switches and limit the read/write access to some OIDs?I have been searching for hours for configuration examples or guides, but i had no luck.I guess a role has to be created, containing rules for some feature, but the list of features doesn't contain anything about snmp.This is my configuration on catalyst switches and i'd like to achieve the same result on the Nexus 5k:
conf term
access-list 10 permit host x.x.x.x
access-list 10 deny any
snmp-server view myview ccCopyTable included
snmp-server group mygroup v3 priv read myview write myview access 10
snmp-server user myuser mygroup v3 auth md5 xxxxxx priv aes 256 xxxxxx
end
View 1 Replies
View Related
May 23, 2011
I have a question about SNMP OIDs for the command "show counters interface intx/y delta" on Catalyst6500. The customer wants to create graphs for the following values:Overruns, qos0Outlost, InErrors, OutErrors, InDiscards, OutDiscards etc..Is possible to get these values using SNMP?
View 3 Replies
View Related
Nov 25, 2012
I can see that the Cisco 881 does not have NTP as standard, but can this feature be used anyway with the latest software upgrade?
View 4 Replies
View Related
Oct 3, 2011
dell xps m1530 i have a Intel� PRO/Wireless 3945ABG Network Connection and i want to upgrade it to N standard which model of intel minipci network will fit to my dell?
View 4 Replies
View Related
Oct 25, 2012
Is there a way that I can specify which version of the 802.11 standards I can use.e.g. I have an 802.11 B/G/N wireless card and I want to test each on a directional antenna to see how they perform
View 4 Replies
View Related
Apr 19, 2011
what's the standard protocol to transfer R2 to SIP?
View 1 Replies
View Related
Oct 22, 2012
whats the difference between custom and standard discovery? There´s a line on the help page: "The Use Policy Configuration Settings radio button will be enabled only after adding a Default Credential Set Policy."The radio button is not enabled although I´ve two default credential sets and two default credential sets policy configuration.
View 1 Replies
View Related
Jun 23, 2011
We have bought lms 3.2 and window server 2008 r2 standard. Now we know, it cant be used together Could we upgrade to lms 4.0.1 ? If so, how can we do ?
View 2 Replies
View Related
Apr 13, 2011
I wanna subscribe to Internet TV. To watch it on computer screen I need to log in to the site where I registered, i.e. enter my login ID and password. But I want to watch it on my TV WITHOUT my PC. I realize that I have to buy a TOP BOX , connect it to TV and to cable modem. The question is how the TOP BOX knows my login and password to pass it to the site through modem.How do I enter it to tob box?
View 2 Replies
View Related
Apr 19, 2011
Can I install win2008r2 standard to a 500gb usb ultra portable harddrive and connect it to my net book and run it ? I am studying for the MCITP and want to use it for that purpose?
View 3 Replies
View Related
Sep 6, 2012
Tech Support Guy System Info Utility version 1.0.0.2[CODE]
View 6 Replies
View Related
Jun 2, 2011
why I cannot get any of the standard ports open on my computer. I have run ESET firewall/antivirus, but have it temporarily disabled. I have windows defender disabled. I have the correct ports open/bypassed through my linksys router, but still am having network trouble.
Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft Windows 7 Enterprise , 64 bit
Processor: Intel(R) Core(TM) i7 CPU 920 @ 2.67GHz, Intel64 Family 6 Model 26 Stepping 5
Processor Count: 8
RAM: 6135 Mb
Graphics Card: ATI Radeon HD 4800 Series , 1024 Mb
Hard Drives: C: Total - 953866 MB, Free - 610614 MB;
Motherboard: ASUSTeK Computer INC., P6T DELUXE V2, Rev 1.xx, MS1C96B19100148
Antivirus: ESET Smart Security 4.2, Disabled
View 11 Replies
View Related
Oct 18, 2011
I have a machine which is connected to a PC using an ethernet cable to communicate information between the machne and computer.I am told that the machine uses the MAC address to communicate and the computer just needs an ip address in the same range as the machine and software aware of the machine's MAC address. Why I can't connect it though the network, I tried the manufacturer who couldn't explain
View 4 Replies
View Related
Sep 26, 2011
can you replace the standard wired modem provided by your ISP with a wireless/wifi modem yourself?
View 4 Replies
View Related
Apr 10, 2013
Can MSE running software 7.0.220.0, work with WCS runing WCS-standard-K9-7.0.240.0 and WLC 5508 running AIR-CT5500-K9-7-3-112.0 ?
View 1 Replies
View Related
Jan 2, 2012
I am looking to add a new DMZ zone to our network with have a standard 1941 (1x LAN / 1 x WAN port) and so I need a 3rd routable L3 interface to create the DMZ.
Is the HWIC-1FE what I am looking for or is there another way to do this?
View 12 Replies
View Related
May 15, 2012
I have a client who does not use exchange, and doesn't need any of the SBS features.Their server is aging and are running out of disk space.
I'm in the process of building them a new file server and am considering using Server Standard 2008.I am even going to take them off the domain and make their server strictly a file server for Peacthree. It is the only reason they even need a "server".
View 5 Replies
View Related
Jan 24, 2013
I´m looking at this document: [URL] and I´m not clear if Windows Server 2008 R2 Standard with SP1 is supported. The documentation refers to Windows 2008 Server SP2 and Windows 2008 Server R2, but I see no specific mention to Windows Server 2008 R2 Standard with SP1.
View 0 Replies
View Related
Nov 15, 2011
I have a RV042 router setup with Client to gateway VPN access, and am connecting with a W7 PC running QuickVPN. We have many PC's that already have the standard CiscoVPN client on them, is it possible to configure the RV042 to allow these clients to conenct? I'm not sure how to get the Mutual authentication to work, or how to import the PEM certificiate into that client. It seems to allow it to import, but I can never select it.
View 2 Replies
View Related
Mar 26, 2013
We got this software from Cisco and we need to setup this in our network to manage the firewalls.Need to know this software is used to centrally manage the firewalls ?Also how i can i know how to setup this in our network?Assuming this software we will first install on server right? it can be windows server ?Second thing to know is what config changes we have to do on the existing and new ASA so that they can be managed centrally?Also Where i will get the documents that tell me how to setup/install this software?
View 5 Replies
View Related
Oct 16, 2011
Does LMS 4.0 support Windows Server 2008 R2 Standard Edition (64-bit )?Is necessary for a fresh installation to download and install the Windows 2008 R2 patch?
View 2 Replies
View Related
Apr 3, 2012
We are going to "publish"(I don't know if this is correct word to use;)) our mail server on Cisco 2921. As far as I know it can be easily achieved with static NAT. But the thing is, we don't want to publish it on standard 443 port i.e. we want router to listen for https connections on other port than 443, and then redirect this connection to internal server with private ip.
View 1 Replies
View Related
Nov 6, 2012
We're installing LMS 3.2 on a VM machine running Windows 2008 Standard edition (64 Bit).
You cannot install CiscoWorks LMS 3.2 application(s) on an unsupported operating system or when Terminal Services is running on the supported Windows 2003 Server Standard Edition, Windows 2008 Server Enterprise Edition,Windows 2003 Server Enterprise edition, and Windows 2003 R2 Server Platforms. The setup program will exit when you click ok.You must either upgrade the operating system on the server to a supported version or install LMS 3.2 application(s) on another server that runs a supported operating system.
I've disabled all RDP sessions and ANTI-Virus Software.The documentation states 2008 server Standard (64 bit) is supported.
View 3 Replies
View Related