I would like to know if there is a way to monitor which programs/processes are using my network, say if there's something in the background updating that I can close to reduce lag in games, my computer is free of viruses and most the auto updates are turned off because I update them manually, so I just would like a simple straightforward answer,what program or process is using my network?
View 4 RepliesI know the general difference between a router and a switch, but after considerable reading I'm unable to determine if I could just use a switch for my pretty simple specific application.
Here are the two devices I need to setup on my network (connections would be wired, both devices in close proximity): (1) computer running windows2k with 100mbps ethernet card (has software firewall installed) (1) blue ray player for streaming netflix videos
Because I don't have any computers on the network communicating with each other, based on what I've read it seems possible to just connect a switch to my cable modem instead of using a router.
I would like to setup a simple VPN on a small network, nothing special, just to provide access to some simple resources on the network from anywhere. Since I'm not a Cisco expert, I was advised to user a 861 router, but I just can't seem to get the VPN working on this device.
I've placed the router behind a modem and did some basic configuration. Hosts who are connected to the modem (on the Vlan side) can access the internet and can setup a VPN connection to the router. A VPN connection from inside the network is worthless, but I just can't get the VPN working on the FastEthernet4 connection.
Any VPN config for a 861 router for this situation? Or how to configure this device as a VPN server?
I will be building my own computer here in the next month and am looking to become quite informed about building my own wireless network.Trouble is, I'm a bit out of to with what I need and what is good. I'm also officially tired of renting a modem from Comcast (bastards keep bumping my monthly rate up). So what pieces of equipment do I need to build a simple quality wireless network for my home? I would like the network to support two laptops, one desktop, and an Xbox plugged into a LAN line. Also, I'm thinking of using a Rosewill Wirelss Adapter 3 antenna [URL].
View 4 Replies View RelatedI have a home network using a 2600 and PIX515E, and unfortunetly I don't know how to set up ACLs. I read a few Cisco documentation but unfortunetly I am unable to grasp the concept of how to define them. Would anyone be able to give me a crash course on setting up ACLs?
View 3 Replies View RelatedWe'll be building a small remote site that will use two Windows 2008 servers. We would like redundancy in firewalls, IPS's and switches. Is it better to buy stand-alone ASA 5510s (with embedded IPS's) and 2960s, or is it a better option to buy a Cat 6000 with FW modules. We'll have several internet IP addresses available.
View 2 Replies View Relatedwhat is network utilization and throughput ?
View 1 Replies View Relatedi have a campus network with 2 core Cat6500 and multiple 4500 series distribution switches plus 2960 series access switches,we have deployed IPTV system in the network but currently 50 TVs are working through sattelite stream from streaming server Cisco's DCM 9900.we are planning to add more 300 TVs in the network and i am wondering that when all of them will be deployed then what will happen for switches cpu utilizations when all the Tvs will be running on the same time with different different channels.
View 1 Replies View RelatedI have a Cisco Aironet 1240AG Access Point and I am trying to setup a guest network that is secure and limited in bandwidth utilization. I see an option under security > SSID Manager on the web interface to select an interface of Radio0-802.11G, Radio1-802.11A or both. Can I put the guest network on the Radio1-802.11A and make it more secure/bandwidth limited or does this option not matter?
View 3 Replies View RelatedI have a 24-hour running computer that I want to make a small and simple server for personal useim: to put some photos on the server for my target audience from China. I have a 24 hour running computer located in my small flat in China. The purpose to make this is to provide a fast speed loading for average users in China? The links for the photo should be in format
View 4 Replies View Relatedim using a intel mother board desktop pc and windows xp. i was tray to add external wireless modem .the modem drivers already install successfully but its not working properly it working only 1st 5 to 10 minute.my pci simple communications controller also not installed
View 1 Replies View RelatedI need to configure ADSL on my 837 Router with simple configuration. The WAN IP address is dynamic from my ISP. I checked many websites and found different configurations everywhere. I don't know which is best suited for me. I used SDM and configured ADSL. When i checked the configuration from console i found that there is atm0.2 and dialer 2 configured with my settings. I cannot understand what is the purpose of atm0.2 and dialer 2 when atm0 and dialer0 are there. Is there a doc on ADSL config on 837?
interface Ethernet0 ip tcp adjust-mss 1412 exitinterface ATM0.2 point-to-point no shutdown pvc 0/35 pppoe-client dial-pool-number 1 exit exitinterface Dialer2 exitdefault interface Dialer2interface Dialer2 ip mtu 1452 no shutdown ip address negotiated dialer pool 1 dialer-group 1 encapsulation ppp dialer idle-timeout 120 dialer fast-idle 20 ppp authentication chap pap callin ppp pap sent-username username ppp chap password 0 password exitdialer-list 1 protocol ip permit
how can you turn my wifi router into a simple wired one
View 3 Replies View RelatedI've been trying to set up Simple file and printer sharing between two desktops with plans to add a third, a laptop. All are running Windows XP SP3. One has XP Pro and the other has XP Home. (The laptop will be XP Pro.) All are connected wireless. They share a connection to the internet through a cable modem and a Linksys router. Each desktop has a USB wireless adapter. I set up a few folders on each to share along with a printer on the XP Home machine. Right away, the XP Home machine was able to access the folders on the XP Pro machine. Alas, not the other way round. It seems I don't have "permission to access the resource".
View 8 Replies View RelatedPci simple communication controller driver software
View 1 Replies View Relatedi'm trying to set up a simple VPN (client to Gateway), but i can't ! An SSL VPN or an IPSEC VPN, whatever..
The firmware of the RV042 is up to date, and i'm trying QuickVPN as a client vpn (also updated...)
My configuration details :
I'm in : 192.168.2.14 /24
My RV042 : 192.168.2.250 /24
And the VPN intend to connect me to : 192.168.4.x
[Code].....
I have a room cut off from the wired network by concrete walls (there are windows and it's a very short distance). There is a device in that room with a wired network adapter than needs access to the network. We'd like to use a pair of WAP4410N devices to get that room on our wired network over a simple "wireless bridge."
Would the following work?
Connect one WAP4410N normally with WPA2 Personal encryption and connect it to our wired network. Enable repeating of its signal.Set up the "remote" WAP4410N in the "cut off" room. Give it the same SSID and Encryption settings. Enable "Wireless Client Repeater" mode and uncheck the box labeled "Allow wireless station to associate". . . then use its RJ45 network port to connect to the wired device in the room. My biggest concern is the part in bold. Will the network port on the "remote" repeater function like that? So that any devices (or a switch) plugged into it will then be "forwarded along the bridge" to the main/local AP and then onto our network?
I've tried setting up some simple port forwarding on my ASA, where I want to forward one port on the external interface for both UDP and TCP to the same port on an internal server.
It works fine for UDP, but all TCP packets are dropped on the outside interface, even though the configuration for UDP and TCP is basically the same! This is my config:
object network MY_SERVER
host 10.10.1.4
object service TCP_MY_SERVICE
[Code].....
Port count goes up on line 2 (UDP) but never for line 1. I just see the packet denied instead. Same thing happens in the packet tracer, a packet destined for my external interface on that port for UDP is allowed and NAT'd just fine. TCP it gets dropped by the ACL on the outside interface.
I am trying to find out if its possible to use an existing CISCO 2940 Switch that we have here at our office as a hub? Im sure that borders on insane however, let me break down what we have currently and what I'd like to do.
We currently have a very nice setup here at work, with no problems whatsoever, however; we hired a new person and brought in some new printers and we are running out of wall jacks. Rather then run all new cabling and adding new outlets/faceplates etc... We were just gonna go purchase a simple Netgear 5 port switch/hub from the Local Comp store here in town. We found in our server room a what appears to fully functional and operational cisco 2940 8 Port Switch with a Gigabit port.
All IPs in the office are assigned via DHCP, so....on to the meat of my question -- I tried to plug this into our network and I can't get any connectivity out at all. All the ports light up green etc when I plug in the comps but they aren't pulling valid IPs.
I want to reset this thing and start from the ground up, I am not scared of going into the IOS and modifying what needs to be done...as long as I got a good enough walk through.
I would like to create 3 x VLANs on an SG 300-28P and have them completely isolated from each other, for example ports 1 - 12 on VLAN 1, ports 13 - 24 on VLAN 2 and ports 25 - 28 on VLAN 3. No communication between any of the VLANs.
Any simplest way to achieve this?
is it possible with LMS 4.0 to do a simple reachability test for an IP address not based on device?The ip address I want to check for reacheability is not the management ip address I add in Inventory->Device Administration->Add->Device Properties->IP Address For example: I want to test the reachabilty of the IP-address 10.113.15.4, not management ip, it shall be an interface ip address.With the performance monitoring I want to test the reachability, if it fails continuously 2 times I want to get a notification with an low severity.After 6 continuously fails of the reachability test I want to get a notification with an medium severity and in the end after 12 continuously fails of the reachability test I want to get a notification with an criticaclc severity. The threshold configuration and the threshold criteria should not be the problem,the problem is where do/can I enter the corresponding ip address I want to test.
View 1 Replies View RelatedI have a cisco ASA 5540 and i cant make a simple PAT (many private IP to one public IP). Below you can find my conf.
[code]...
I`m trying to get a simple VRF and routing setup going.The "routers" are Cisco C3750G-12S-E.What I want to do is separate the management network form all else.The public network is illustrated with private IP ranges, these are really public ranges.
I think the best way to solve this will be using VRF for management, and regular routing for public network, right? Putting the management network in it`s own VRF.
I'm new to routing and cisco in general. I'm inheriting a rather simple setup but would like to approach the next steps with a good strategy. Currently we have a 2901 router with public IP's on bother interfaces. The internal facing interface is our gateway for some webservers and a firewall. Not we are looking to add a colocation site and establish a site to site VPN using another 2901. My goal is to have the colocation use the same internal 10.100.0.0/23 network. My question is what is the best way of going about this since the router at the main site has public IP's on both interfaces? Do I need to multi-home the internal facing interface? If so, what else needs to be done?
View 1 Replies View Relatedhow to download pci simple communi..... for dell laptop
View 1 Replies View RelatedI have laptop or desktop both computers and i want to share my desktop matter in my laptop or laptop matter in my desktop without using any modem by the using of a simple cores cable? how i can handle it..
View 1 Replies View RelatedGo to Control Panel.
Click on Network and Sharing Center.
Click on Wireless Network. Connection. (your nickname for router should be listed underneath).
Click on Wireless Properties.
Click on the Security tab up top.
Click on the checkbox where it says “Show characters” and it should be spelled out for you.
I have one POTS line and a SIP account with Skype. I want to configure my SPA3102 to take all incoming POTS calls (so I don't have to change my phone number or use up my bandwidth all the time). I want all local calls (303 and 720 area code) and possibly 911 (if possible) to go out the POTS line, but all long distance to go to SIP account on SKYPE. Pretty simple, but I can't find a wizard or samples in the documentation or firmware for the SPA3102.
View 1 Replies View RelatedI just got a new rv120w and want to set it up, like my old router. I have a webserver that people around the world, should be able to visit, but I can't figure whats wrong. You can see my settings in port forwarding here.
View 4 Replies View RelatedI need to replace an ADSL modem and have a spare 857W. Can I use this to act as a simple bridge between the ADSL PPPoA connection and the FW WAN port?
[ CISCO 857W ]
ISP - PPPoA - BRIDGE - FW WAN
I have a block of Public IP's so the PPPoA Dialer 0 connection would get x.x.x.185/29 I would like to bridge this directly to the FW WAN port and set that to x.x.x.185/29 with a gateway of x.x.x.186/32.Currently I am using it in router mode with no NAT or FW and am losing a Public IP as I need to set the FW WAN as x.x.x.186 with a GW of x.x.x.185 I am setting BVI 1 as x.x.x.185/29 and Dialer0 as IP Unnumbered BVI 1.
Need simple configuration for the Aironet 1142N? Optimally, I would like to place 802.11b/g traffic on the 2.4 GHz band and 802.11n traffic on the 5 GHz band.
View 2 Replies View RelatedHave a Linksys E-3000 router and a WAP-4410N which I wish to configure as a repeater to extend network coverage. E-3000 IP has been changed to 10.10.1.1. How do I do it ? What do I connect to what in order to configure the WAP-4410N to new settings? It will of course be located remotely from the router. At this time network consists of a main PC and 2 wireless laptops. I have read the manual and it doesn't answer the above described situation.
View 7 Replies View RelatedJust got a D610 with no drivers cd. Rebuilt the laptop with TxDOT image and now I get a message found new hard ware pci simple communications controller. Where can I get this driver at?
View 8 Replies View Related