my laptop isn't showing my wireless internet connection in the list.But my phone is connecting to my wireless internet connection without any problem.I am using a Toshiba Satellite laptop with Windows Vista.
So, I happened to do CD recovery a day ago; *Due to forgetting Administrator password* and now my laptop seems to not be able to pick up any wireless connections when there usually is a ton. Also every time my laptop restarts it always loads saying "Preparing for first time use" Like I used the CD recovery again. which I didn't. I thought that maybe it has to do with the Drivers and such, though im not very tech fancy, so I wouldn't exactly know where to find the correct driver to install, and which to install.[code] Oh and lastly, I happened to notice on Driver manager, that on "other devices" there is a yellow exclamation point, on both of them: Intel(R) Centrino(R) Wireless-N + WiMAX 6150 and Network Controller.
We have a old Router and a new one(the Lynksys). The old one had problems with the Wifi so we bought this one. So when we connect This Router to the Modem it doesn't show connection to the internet. (The Setup fails because of this).†But with the old one it does connect to the internet. So either my modem doesn't detect the new router or vice versa. So I am not sure why its not working since on the old one it works fine.
I have had my DIR 615 router for about 6 months, and have had no problems. I have a notebook (Sony Vaio) and I also have a Blue-Ray Player and my DirecTV DVR connected by ethernet. Starting a few days ago I was having connectivity issues. At first I could see the network on my Vaio, but the Internet kept coming and going.I did some troubleshooting on the adapter and that seemed to work. Now I am having an issue where every 2 hours or so the wireless drops and the network disappears from the list of available connections on my notebook. I have had my netbook on (connected wireless) and the issues are replicated on that system.
Both of my wired devices do not see any interruption in connectivity. Living in an apartment complex I suspected interference and indeed there are a ton of other networks in range (as per inSSIDer 2.0). As there is no channel that is clearly open, I have set my router to auto channel scan. I also have tried some of the steps outlined in other threads. The thing I am noticing is that when the network connection drops my network (which has a unique name) doesn't even show up on inSSIDer, it just disappears. When working, my network is consistantly in the -25 range on inSIDDer.I should point out also that my notebook is a mere 8 feet from the router, and there are no obstructions.
I have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
we have netgear wireless router. plug in the line from the dsl or cable modem to router and line out to our reg pc. Our wireless laptop shows that there is a connection to our wireless network but will not bring up a web page. The line out to the home computer will not bring up a web page when coming out of router to pc or to laptop. Is it the router? we have powered it down and hit the red button on the back to reset router but still nothing, how do we fix the router?
I am trying to connect to a different network, but for some reason when I click "Connect To", where it tells me to click to join another wireless network, it just shows me this: and does not show me the Wireless Networks that are available (I am not sure what it is called)
I'm using a wlan controller with 1242ag converted to lwapp, i'm trying to enable 5.8 but when i change the from local to bridge the lwapp disappear from controller. May be that the firmware does not support mesh !I'm following the 4402 wlan manual at page 641.
I'm trying to connect my computer to our router with no success. Windows doesn't detect the wire when I plug it in, no matter which one I use. This has never been a problem before I recently installed Windows 7 HP.I had no wireless connection to the router either after I installed the new Windows, but following an answer to a remotely similar question in the forum fixed it ('scan for hardware changes' on "Realtek Wireless LAN" under Network Adapters in Device Manager)
Dell Wireless 1390 WLAN MiniCard on my Inspiron 1521 with WINDOWS 7 does not show in the device manager. There is a popup window that says Driver blocked due to incompatibility.Ive tried to install new drivers but it doesn't work.
I have a linksys E3200.¬† Today I got disconnected and when it reconnected it stated that the network was changed to just network and not my usual network name.¬† I was having connection issues with the network disconnecting me and reconnecting me.¬† I uninstalled the cisco connect software.¬† I contacted support who told me to restart the router and modem, which I did.¬† After reset I tried to reinstall the software.¬† Cisco Connect likes to insist to do the installation wirelessly but my laptop can't find the router during installation to complete it.¬† My router is essentially a glorified wire connecting my computer to my modem now.¬†
How to approach an overnight upgrade from autonomous AP1231/1242 deployment into a 2504 controller-based AP1602 deployment.I do not have access to the existing 1231/1242 deployment ==> I need to ask network manager for all necessary config info to be ported onto the 2504.Example: the 1231 show run output does not list the various SSID that are in use.Therefore the question is: which commands' output do I need to ask to have all possible config data from 1231/1242 to use when configuring the 2504/1602 deployment.
i am having an annoying issue with my wrt400n and my foscam FI8918W.¬† in the dhcp reservation tab, the wrt400n doesn't show the foscam anywhere in the tab.¬† it shows all laptops, cell phones, nases, etc.¬† if i use the cisco connect software it does show it in the network map.¬† i can probably add it manually via the gui.¬† is this something normal or security cams not considered devices?
Region : UnitedStates Model : TL-WR1043ND Hardware Version : V1 Firmware Version : 3.13.12 Build 120405 Rel.33996n ISP : WR1043ND
The router is not showing my external hard drive in the usb settings. The Hard drive is a seagate 7200rpm 1.5tb. The hard drive works just fine when plugged into my computer. I have tried NTFS and EXFAT. My 2gb usb drive in FAT32 shows up just fine. The external has its own power supply. Is there anything I am missing that would cause it to not work?
Every once in a while when logging into Windows (7 Ultimate 32 bit) My PC decides it couldn't find a network connection, usually restarting the computer solved the problem, however now I have seemed to permanently be stuck on the "identifying" stage of my LAN connection. My mobo is an Asrock p67 extreme, the network adapter is a realtek pcie family card.Now I know it is not my modem since I can connect on my other PC in the living room, I verified this with a phone call to my ISP, they couldn't see my PC connected to the network but could see the other one.It is not the Ethernet cords, I switched them and even used a new one. I tried rolling back, installing updated and installing factory drivers for my network card, no change.
I tried turning off the PC, disconnected the power cord, discharged it, left everything off/ disconnected for 30 minutes and reattached, powered on, no change.I made sure my DHCP was on and that my PC was set to automatically retrieve IP/DNS.I even bought a new Ethernet card, installed it and I still can't connect, so its not the realtek card.I can't even access my modem using its UP address, 192.168.2.1 (Bell 2wire) but I can on my 2nd PC, it sees all other devices, PS3 /Smartphones but not my PC.
I am running a DIR-825 I believe one of the original's no updates or anything.¬† I run it mixed mode.¬† The 2.4 shows up and I can connect to but the 5 ghz (n) speed says it's enabled but I can never see it when I scan on any of my wireless n products (laptops and other computers).¬† Dlink support told me to change to mixed mode g and n.¬† I was running it in mixed mode (a, g and n).¬† D link told me to change to mixed mode g and n and to make sure they stay on channel 6 and 11.¬† Is this correct.¬† Which firmware should I upgrade to and is there any easy way to do this?
The Cisco 887 doesn't support the show dsl command, what is the command that I need to use to display the speed my ADSL is operating at? On the Cisco 877 the command I use is show dsl int atm 0 but this doesn't work on the 887
why does my laptop not even show any view wireless networks.In the wireless connection status box, it only says properties, disable but where it should say view wireless networks there is nothing! It is blank. Why is this? And how do I get it to view my wireless networks? I have tried a wireless usb adapter which I use for my other laptop. That usb adapter is comptabile with both WEP and WPA and the computer does not pick up the software. I don't know what else to do.
Im working for a client at the moment and I've had to setup a network printer for them, I've got 4 Windows 7 machines easily printing over the network to this printer that is connected wirelessly but they want one of there machines to use the scanning functionality of the printer.The scanner doesn't show up at all in the local network devices like the printer does and to be honest i don't really have any experience with scanning over a network to a windows 7 machine, but this printer does support scan to ftp so my idea is to setup a small ftp server on the windows 7 machine with a folder to stored scans on the desktop or something, then put the details of the server in to the printer making it as easy as possible for the customer to scan stuff and just get it from the folder on the desktop, i could also share this folder over the network for anyone to open and get a scan if needs be.
I put Win7 on a customed pc bought online. The motherboard has an Atheros L1 integrated NIC and I installed a Dlink dge530t NIC into a PCI slot. I know I have to disable the onboard nic but the installed card is not comming up either in Device manager or network connections. What gives? In the bios under integrated peripherals i did enable PnP OS.
LMS discoverd all my devices and updated the DCR. This devices are visible in DFM. For some of this devices i would like to change the threshold values. For some reason the devices are not visible in Monitor->Fault Settings->Seup->Threshold Settings (please see screenshot) Is there another approach to change the threshold values?
I've enabled RDP on a laptop, but I can't connect to it. Pinging the laptop works. nmap shows ports open, but not RDP. netstat on the laptop shows nothing listening on 3389. I've also tried rebooting. [code]
I Have installed LMS 4.0.1 for my client. I have also installed UTLite script on the domain controller as per instruction from cisco. When i look at the utlite.log i'm seeing message displayed below: ¬† Failed to create Tables. Transaction Rolled back Failed to create Tables. Transaction Rolled back : com.sybase.jdbc2.jdbc.SybSQLException: SQL Anywhere Error -110: Item 'getAuthenticatedUsers_ACS' already exists Intializing the Controler 9 = skt Pkg = com.cisco.nm.cm.ut.ctrlplane.ctrls.SocketCtrl 2011/08/25 14:59:14 main utlite INFO SocketListener: Socket Listener : Port : 16236 Started Socket Listener
I recently installed some wireless IP cameras and when attempting to re-install a camera I went into the DHCP Client table to verify which IP a camera was using to set it up, but¬†I could not...and still cannot see any of my cameras in the table even though I can access three of them directly through the IE web browser. I initially power cycled both the E4200 router and Motorola cable modem, and then later just the wireless router...but I still do not see the devices connected. I currently have 2.0.37 firmware even though I was told by Cisco support that there was a later version available, just before being informed that I do not have support available and could purchase it. I attempted to locate a newer version, but the online upgrade portion of the Cisco Connect software searched the net and then states that I have the latest version available. I also opened a Firefox browser to see if maybe my browser was causing issues, but the same limited table appears without all entries available. I even opened the Cisco Connect software on another laptop with the same limited results. Other than a factory reset, get me E4200 dual band wireless router to show all attached devices through the DHCP Client table as it previously did approximately two weeks ago?
i have a dir 825 with fw 2.00eu that i wanted to upgrade to the new beta fw.i went to tools and did a factory reset first,when i wanted to log back in to load the new fw,it sudenly asks for a authentication code,problem is the field is marked with a red x so i cant see any code i'm using windows 7 and IE 9?