Cisco :: LMS 4.2.2 Fault Monitor Suspend Device
Nov 6, 2012i´m looking for two hours now and can not find a way to suspend a device in the Fault Monitor. We´re using LMS 4.2.2
View 1 Repliesi´m looking for two hours now and can not find a way to suspend a device in the Fault Monitor. We´re using LMS 4.2.2
View 1 RepliesI've just installed LMS 4.2, like it a lot so far. In the Fault Monitor, the Device Name column shows the device's IP address rather than the host name. We need for it to show the host name, for ease of troubleshooting; most folks don't have the IP addresses memorized. Likewise, when an email is sent out for an event, the managed device field also shows up as the device's IP address.
The devices were all discovered with their IP addresses rather than a host name...should LMS have automatically found their host names? Regardless, I manually updated all of the device's host names, yet they still display as an IP address in the fault monitor.
Also, it appears I need to figure out some way to throttle alerts. One particular device will report an event (ie a temperature out of range) dozens of times in a polling period...several per second, even though it's the same alert.
Despite there are all devices are managed in DFM (accorduing to Collection Summary Portlet or Rediscover devices) there are no devices in the Fault Monitor with the message "No devices are available"Does it mean, we have absolutly no faults in our network or does it mean that we have a problem with DFM?
View 2 Replies View RelatedHow to find out which Fault Threshold group a specific interface belongs to.The scenario is that in Fault Manager there is an alarm for which I want to change the Threshold Setting.
Example Alarm:
Event_Description HighUtilization
Device IP x.x.x.x
Device Type Routers
Fault Last Updated At 19-Mar-2013 09:44:25
Component IF-router2.x.x/26 [Tu187] [x.x.x.x]
[Code] .....
I try run Fault monitor feature in LMS 4.0, but I got error like this picture :
View 3 Replies View RelatedI am working with LMS 4.1 and FDM 4.1.0.
If I ask to the Supported Device Finder Portlet about C4503-E (SysObjectId: 1.3.6.1.4.1.9.1.874), it tells that this device is supported by DFM 4.1.0. Nevertheless, in DFM module each one devices appear in the "All Unknown Devices" group, with Error Code: Unsupported. CDP is enable in each one of these devices.
Cisco Prime 4.2. My device is stuck in Questioned state in Fault Management. The device though can be pinged from the server. Actually, I can already manage the device and have archived its configuration. Problem is, on Fault Monitoring Device Administration, its on Questioned state even though I already tried to rediscover the device several times.Do I need to configure something on the server like put in the IP address and hostname of the device in the host file of Windows Server 2008?
View 1 Replies View RelatedI configured an Etherchannel two interfaces (Gi0/37 and Gi0/39) in a CiscoWS-C2960G-48TC-L, which is connected to an HP Blade, where they spend 2vlan (16 and 17). The point is that they got these interfaces on a trial and upload these were in sleep mode produces the following log.
Sep 1 16:04:38.649:% EC-5-CANNOT_BUNDLE2: Gi0/37 is not Compatible with Po1 and Will be suspended (trunk mode of Gi0/37 is dynamic, is Po1 trunk)
Sep 1 16:04:38.733:% EC-5-CANNOT_BUNDLE2: Gi0/39 is not Compatible with Po1
and Will be suspended (trunk mode of Gi0/39 is dynamic, is Po1 trunk
nyone know if "vpc-orphan-port suspend" works if i put on N2k interface. not the fex link. example i have fex 101 and i put on eth 101/1/10 will it suspend the port on N2K connected to secondary N5K when peer link is down?
View 2 Replies View RelatedFor a week now, one of my Cisco 3945 routers displays, from time to time, the following message in its log:
2012-07-16T14:12:43.852017+00:00 cb00-r103 220: [syslog@9 s_sn="59"]: Jul 16 16:12:42 MEST: %SYS-2-INTSCHED: 'may_suspend' at level 4 -Process= "OSPF-100 Hello", ipl= 4, pid= 320
2012-07-16T14:12:43.852017+00:00 cb00-r103 221: [syslog@9 s_sn="60"]: -Traceback= 15CB073z 9081B7z 2851571z 11B7582z 11C275Ez 11C2906z 11C03E3z 1B907B5z 1B9064Cz 1BA5737z 172047Fz 47FFDCz 4D2EEDFz 4D2ED71z 4D2EA2Bz 4D30097z
2012-07-16T15:06:11.686817+00:00 cb00-r103 222: [syslog@9 s_sn="61"]: Jul 16 17:06:10 MEST: %SYS-2-INTSCHED: 'may_suspend' at level 4 -Process= "OSPF-100 Hello", ipl= 4, pid= 320
2012-07-16T15:06:11.686817+00:00 cb00-r103 223: [syslog@9 s_sn="62"]: -Traceback= 15CB073z 9081B7z 2851571z 11B7582z 11C275Ez 11C2906z 11C03E3z 1B907B5z 1B9064Cz 1BA5737z 172047Fz 47FFDCz 4D2EEDFz 4D2ED71z 4D2EA2Bz 4D30097z
[code]....
It never happened before and the configuration did not change. The only thing that happened, the WAN connection (point-to-point to a Cisco 3845) went down and the router rebooted while the WAN was down. When the WAN came up again, everything went fine, until about an hour later and the first occurrence of this mentioned log.This 3945 does establish an IPSec tunnel with its peer (the 3845) and all the traffic, including OSPF, is going through the tunnel.
I upgraded the LMS 4.0 with LMS 4.0.1 but now the events are removed of Fault View. The equipments than I am monitoring are: ME-3600, ME-3800 and ASR 9000. This is a configuration problem or I have to update something else?
View 1 Replies View RelatedI have a Sony Viao laptop with WinXp SP3 which is now 6 years old. We are currently renting a holiday home in the USA which has an unsecured network. We have two other laptops and they are connected, no problem. This morning my Sony worked fine on email and web access but I was having trouble on FTP. Then email stopped and then web.I have tried all the usual solutions. Delete the Network, restart etc etc.It clearly show the network (and also another secured network I cannot access). When I connect it shows "Acquiring network address" then just hangs. If I press, repair it hangs on "Renewing your IP address" Does the fact that it can see the networks and when I "ping 127.0.01" it seems to be OK, mean that it CANNOT be a hardware fault? I ask this partly because the WLAN switch at the front often does not seem to work (when it does work it is green and currently it IS green)
View 9 Replies View RelatedThis is Cisco Prime LMS 4.2.2 on Windows 2008 R2
As far as I understand it Fault Manager need to be able to do reverse lookup for ip adresses to show the correct name in the "device name" column. I have double and tripple checked and all devices that only is shown as an ip address do have a reverse in the dns used by the LMS server. The device is correctly registered and inventory have been run. If I hold the mouse pointer over the crosshair on the row of the offending device all info is shown including correct device name and fqdn.
The server is upgraded from 4.2.1 to 4.2.2 and we have the same problem before the upgrade.
I have an ISR 1921. Every now and then, it crashes saying "Possible software fault". The system LED flashes amber and only a hard reset (power on/off) will reload the ISR.
View 2 Replies View RelatedI am trying to setup Fault Monitoring on LMS 4.0. When I try to create a Fault Notification Group no devices are listed. They appear to be listed in all other places so I am at a loss as to explain why they are not appearing.
View 7 Replies View RelatedI have an inventory added to Ciscoworks and am getting alerts on interfaces that I want to exclude but for the life of me I can't figure out how to exclude interfaces. Any tips on how to exclude interfaces from the fault engine in 4.1.
View 3 Replies View Relatedi have trying for a few days to connect my HP G7000 notebook to the internet through my wireless but i have tried everything i can think without getting anywhere. I only got it a few days back for my daughter to do her homework ect, but can't get it to connect i see a post on here about updating drivers but i can't get it to connect to do this, then thought about downloading the driver update it may need to my laptop but i really dont want to download anything onto my laptop as its a different model with different drivers and dont want it to stop my laptop working.i get on the HP G7000 is cannot communicate with primary DNS server 194.168.4.100 then underneath that message it is saying Network diagnostics pinged the remote host but did not receive a response
View 3 Replies View RelatedWe are running LMS 4.1 and we have more than 150 devices.LMS could not find the fault discovery for 3 switches with partnumber WS-C3560C-12PC-S. This switches are considered as unknown.Ios version is c3560c405-universalk9-mz.122-55.EX3.bin But other things are ok. Inventory Collection ,Config Archive, Topology Data Collection etc . Is there any way to fix ths issue? We have compact switch WS-C3560CG-8PC-S, which is working perfectly for all features.
View 4 Replies View RelatedLMS discoverd all my devices and updated the DCR. This devices are visible in DFM. For some of this devices i would like to change the threshold values. For some reason the devices are not visible in Monitor->Fault Settings->Seup->Threshold Settings (please see screenshot) Is there another approach to change the threshold values?
View 5 Replies View RelatedI'm trying to configure Fault Tolerance on a pair of 4710s. I followed the doc, and configured int gi1/4 as the fault tolerance interface, using vlan 12. However the GUI is saying FT Vlan Down
The troubleshooting wiki said check the physical connectivity, but everything there looks good. Each ACE can ping it's own IP, but not the router on that VLAN, or the peer. They're connected to a dedicated VLAN in a switch, and I even tried a crossover cable to directly connect the two. [code]
I am running my laptop on Windows 7 Proffesional 32 bit and it won't let me search for a wireless connection on the Control Panel I think it might be a problem with the wireless switch at the bottom as it doesn't show the wireless sign on the laptop. I have also tried running the laptop on Ultimate 64 bit but the problem continued to persist.
View 12 Replies View RelatedI have a 1Gb network set up whereby I have a Netgear 26 Port 1000Mbps unmanaged network switch at the heart of my home network. What I have the problem with is devices connected on any one of my 3 300Mbps access points drop out showing no internet but they really mean no network access unless i disconnect and reconnect or switch to another access point. Other things I get happening is one min i have a transfer speed wired connection to wired connection of 35Mb per second and then I only have 8 or less. I am wondering if I have cable issues but before I went out and spent about �100 on new belkin cat6 cable I would ask if there is software I can use to test all the devices on the network so I can replace the faulty item.
View 3 Replies View RelatedRegion : UnitedArabEmirates
Model : TD-W8961ND
Hardware Version : V1
Firmware Version :
ISP :
I have two W8961ND, one for may office and the another one for use at my home, I tried to upgrade my device but during the upgrading the power supply plugged out and after that my device didn't boot up any more, so how can I repair my device, Is there any uploader for it's hardware chip because it doesn't work with it's LAN port or WIFI at this moment
have a Dell Inspiron 1525 and when I revived it from years of neglect I have come across a problem that I cannot connect to a wifi connection.I know that in order for the wifi to be found the wireless in my laptop has to be turned on, however the light on the side does not switch on.So far I have installed drivers and even bought a new wireless WLAN card...And still it does not work.The laptop runs fine with wired connection but I want to use wireless?
View 3 Replies View RelatedI am working as a Network Administrator. Here I have to manage Cisco Switches 2960 and 4500 Series, Active Directory, Database Server, Exchange Server, File Servers, IP Telophony, Fortigate Firewall, 2960 Router, Wifi availability within Company. Although, in case of any disaster we will contact to vendor for solution, but the management told me to deploy any Software/Network Monitor which will facilitate to manage all this, i.e, overall network Health check, Performance Measurement, Fault Tolerance.
View 2 Replies View RelatedI would like to know if there's a way to show Current-Utilization percentage within the messages generated by the Fault Management Module in LMS 4.0 [code] As you can see above CurrentUtilization percentage is not shown in Event Description section.
View 2 Replies View RelatedLately I encountered random Internet connection issues?My router is a Netgear Wireless ADSL Firewall Modem Router DG834 (Firmware V1.05.0) and my ISP, isn't the most reliable regarding bandwidth... All clients (max 3 at the same time) connect wireless.The problem is that the last few weeks my connections is very unstable, all clients lose the internet connection until you restart the router manually.I can't even connect to the webinterface (192.168.0.1), during the downtimes.
View 4 Replies View RelatedI created some User Defined Groups in LMS 4.1, now I want to apply certain fault notification groups to Event Sets.
Unfortunately the Groups I configured are not in the Group Selector of the Fault Notification Group: Admin > Network > Notification and Action Settings > Fault Notification Group
We are using LMS 3.2.1 with SP1 and Campus Manager 5.2.2.Server runs Windows 2003 R2.Everything runs fine except for User Tracking on two Catalyst 6500 switches running CatOS. These devices are discovered, reachable, SNMP works fine, neighbors seen. But when we try to launch acquisition, the UT utility complains with this error message:"Failed to start acquisition: Device unreachable. Please enter a valid device."When we wanted to add ports via Device Trap Configuration, LMS has fired a different error message: "There are no ports to configure for the selected device(s).Check whether you have selected any router(s)." I have checked the portsData.xml file, which doesn't have any ports included for the two devices: [code] We have tried to exclude / include the switches in the data collection, but that didn't work.
View 3 Replies View RelatedMy BEFSR81 is my primary router and has DHCP turned on. The router's DHCP range is set to accommodate 12 devices. I have three computers wired to it and their Host names (as specified in the set-up of each computer) show up in the router's DHCP device table. I also have two printers (one old Brother HL5250DN laser printer and one new HP Photosmart Premier C410a inkjet printer) connected and there are blanks where the Host name should go. I would like to be able to tell which printer is which when I am looking at the DHCP device table. How can I get a names associated with each printer's IP address in the router's DHCP device table? (The real problem is that the router seems to have both printers at the same IP address (192.168.1.100) and if I can get one of them to change I'd like to know which one it was!)
View 1 Replies View RelatedThe problem: I need to track a bus from city to city in real time.I'm thinking of a gps device without screen or apps, it only sends the current location to a server. Is this possible? What device can be useful?
View 1 Replies View Relatedbest way to monitor delay, latency and jitter between sites connected by VPN? I have CiscoWorks LMS 4.0 but that doesn not seem to be able to do the job (or I just don't know how to to it in LMS) Even a 3rd party application will do. I would prefer not to have to place hardware at each location though.
View 2 Replies View RelatedI have a cisco 2911 router that is located in my head office LAN and I use this router to connect to my branch networks. I want to configure IP SLA Monitor on this router to track my WAN Links but it does not support the command IP SLA Monitor. My IOS VERSION is c2900-universalk9-mz.SPA.151-2.T1.bin. how I can configure IP SLA on my router.
View 4 Replies View Related