Cisco Routers :: Forward Range Of Ports With RV180W?
Oct 14, 2012
I am new to the RV180W. I am running the most recent firmware--version 1.0.1.9.
I am having trouble getting FTP to work with my QNAP NAS.
QNAP indicates that I should forward ports 55536-56559 to my NAS. I created a custom service to accomplish this, and then, under port forwarding, I selected the service and forwarded it to the private IP that corresponds with the NAS.
However, the port forwarding configuration only allows me to specify *ONE* internal port. With other routers I have always specified the same private port *RANGE* that corresponds with the public ports that I have opened up.
I have an ASA 5505 running 8.4(1), and I'm configuring it with ASDM 6.4(1). The outside interface is configured with a single static address. I have a few services port forwarded sucessfully to three different servers on the inside network.
I need to make a media proxy on a SIP server available to the outside. It requires a large range of forwarded UDP ports for the media channels.
I tried adding a network object NAT rule like the others I'm already using to forward HTTP and RDP. I entered a range of ports for the real port and the mapped port using the syntax 60000-60999. ASDM accepted it, but the NAT rule list displays "Any" in the service column. When I apply the change, I get the following error:
nat (inside,outside) static interface service tcp 60000-60999 60000-60999 ^ ERROR: % Invalid input detected at '^' marker.
How do I forward a large range of UDP ports from the outside interface to a single server on my inside network? I'd like to use ASDM, but I can switch to the CLI if that works better.
Until now i used a D-Link router with a DDNS account on dyndns.com. I used the ddns account for accesing the surveillance camera when i wasen't at home. The ports for the cameras are 80 and 83.I have a static ip and when i tiped the IP on broswer i was able to acces the camera with port 80 and when i tiped ip:83 i was able to acces the camera with port 83.Today i got a RV180W router made de configuration (ddns, port forwarding) but now when i type the ip address i can't see the camera, instead the router interface is loading and when i tipe ip:83 i get the message "The connection has timed out".I've tryed diferent things but i can acces the camera only by internal ip (192.168.1.x) but using the DDns address i can't acces the camera.
I updated my RV180W to the latest firmware and found that port forwarding works I started using it.I've just noticed that since changing over to the RV180W, my Apacher server logs show the router's IP address instead of the remote IP address - every remote request appears to come from 192.168.0.1.
I am attempting to forward port 25565 on my router, and having some trouble. I've set a static IP address as both 192.168.2.10 and 192.168.2.111, and attempted a dynamic IP address. The port forwarding page via 192.168.2.1 in the browser looks like this, with the Private IP Adress changed to whatever corresponding IP address I have set (checked with cmd /ipconfig).
After testing with multiple online port checking tools, the ports remain closed.
How do I forward ports on the N600 DB F9K1102v3? I have looked through everything. When I go to port forward, I enter the info and have it all down correctly, I click save and once it reloads it isn't there and the port isn't forward.
A client is thinking of putting in a srp527w. they get assigned a static ip on the adsl interface (165.228.204.x), and then have been assigned another block(203.39.183.x/29).how can i have it so that i am able to forward individual ports from the external ip's, to selected internal ip's.
I am trying to add a couple VOIP phone units that do not have their own router. They are designed to run of the existing router and have three ranges of UDP ports opened up. They also do not advise using internal (private) statics on the phones. So what they are asking for is three different ranges of UDP ports to be opened up to all behind the router?
I cannot figure out how to do this (or if it is possible) with a RV016.
I got : RV180W router updated with the last firmware.Static IP for the DMZ host (Synology Server 212+) My problem is that I had try all combinaison since 10 days to get IP source in synology interface (to block IP's of bad connections...) but, I only see the RV180W adress....So impossible to block bad connections IP.
I would like to ask if what is the difference between RV180W-E-K9-G5 and RV180W-A-K9-NA specifically the -E and the -A. As far as I know -A is the compliance code for Philippines. Am I right? If yes, what about -E? There is a documentation for wireless complaince on Aeronet devices but what about these SB products?
I've just bought a Cisco 887m-k9 and I am trying to forward the ports. I have a Polycom HDX H.323 device connected to it with a static IP of 10.10.10.5 (ethernet port 0).Previously I had a consumer grade Linksys router which worked fine (I simply entered ports into the GUI), but I couldn't hardcode LAN port speed so I bought this. I have the list of TCP and UDP ports which are forwarded using the following commands:
ip nat pool Polycom 10.10.10.5 10.10.10.5 netmask 255.255.255.0 type rotary ip nat inside source static tcp 10.10.10.5 80 88.xxx.xxx.49 80 extendable ip nat inside source static tcp 10.10.10.5 443 88.xxx.xxx.49 443 extendable ip nat inside source static tcp 10.10.10.5 1300 88.xxx.xxx.49 1300 extendable
[code]....
Where 88.xx.xx.49 is my static IP, while 77.xx.xx.170 is my default gateway.
I had a DI 604 router and I couldn't forward ports, someone told me to buy a new router because my modem (TM602G) doesn't have a built-in router and can't be blocking it so I bought a DIR 601 with wireless and I still have the problem.I don't have any firewalls.
Ive been having trouble opening any ports on my windows 7 desktop. I connect wirelessly to my D-link Dir 655. I've tried port forwarding single ports to a static ip, but that didnt work either. I currently have the dmz server enabled and still no ports are open according to this port checker Open Port Check Tool - Test Port Forwarding on Your Router I have the windows firewall service disabled, upnp is enabled on my computer and router, i have spi firewall disabled, qos is disabled, and endpoint tcp/udp filtering on endpoint independent.
I'm trying to open ports 2934 and 2935 UDP on my Linksys E1000 router in order to play Falcon 4: Allied Force multiplayer but it's not working.I've correctly created a static IP, and logged in to the E1000's page. Under "Applications & Gaming", and then under "Port Range Forwarding" I entered values thus:
I cannot successfully forward ports on this router, I've tried a few things but I can only assume the firmware is bad. I've already looked around for a solution but everyone says they solved it by just getting a different router (which at the moment isn't an option).
I can't get port forwarding to work, even when I turn off the Windows 7 firewall and AVG anti-virus software I'm running. I entered the IP address of my laptop (with a DHCP reservation) and UDP and TCP port numbers, with Schedule set to Always and Inbound Filter set to Allow All. That should be it, right? However, when I check the ports using PFPortChecker, both the UDP and TCP ports are blocked. I do have a Linksys wireless router daisy-chained to the D-Link router, but I'm not communicating on this computer through the Linksys router and the problem still occurs even when the other router is disconnected, so that doesn't appear to have anything to do with the problem. I just updated to the latest firmware (3.13NA).
We're trying to get a remote access setup for someone who needs to have access from offsite. To make things easy we set it up with a virtual machine running Windows 7 and RDP. Because the "other end" isn't our computer and we've had some difficulties with people using the Cisco VPN client successfully, we were just going to set up a machine as a RDP Gateway and forward the port through the firewall (WebVPN might be nice, but the plugins only do RDP through v5.x). I've tried this on 8.4-1 and after reinstalling the latest 8.2, and supposedly the NAT works and there is a firewall rule allowing access from the outside to the RD-GW server on HTTPS, but the ASA is still blocking those packets. I've looked at 4 howtos and followed them, trying from the console and from ADSM (and one trashed the whole setup, probably related to the reinstall of 8.2) - [code]
I have a router 1802 with a several vlans with IP 192.168.x.0/24 for each vlan (x, it meaning 1, 2, 3, 4, etc.).Now I need that an IP address outside from my network (this IP it is always the same) to be access to on particular machine that is in a private network (192.168.3.0/24) through a several ports:
I am trying to forward both TCP and UDP ports 3074 but it looks like I can only have either TCP/3074 or UDP/3074 open one at a time. When I try to enter the UDP/3074 NAT statement, I get "ERROR: NAT unable to reserve ports". [code]
I need to forward some ports for remote desktop and remote outlook which I host on an internal server. I have looked all over the web and got close, but no hints on how to do it in the asa 8.2. there is an 8.3 guide, but it is just different enough to not work. I am new to this device and cli.
I went out and upgraded to the E3200 a week or so ago and since then i've been unable to forward any ports. I've tried pretty much everything I can think of: disabling Windows firewall, setting a static IP for my computer, setting a static IP for the router, enabling forwarding in both single and range menus, DMZ etc.Here is a screenshot of the port forwarding page just to confirm that i'm doing nothing wrong:In the above photo you will see that I set the computers static ip to x.1.2 and I later changed it to a value that was within DHCP range as listed on the status page of the router admin gui and it still didn't work.So, what I ask of you guys is if you can think of anything that I must be fundamentally doing wrong in order for this not to work. Could it be that i'm missing some possible drivers or network utilities on the computer i'm trying to forward ports too
where 192.168.1.150 is my server (that hosts SQL server and that I want to be able to connect to remotely using VNC) and GigabitEthernet0 is my configured WAN interface.
When I try to connect from an external client I get the error: "Failed to connect to server..." Is this a firewall issue? How do I get round it? The 819 is the only router/firewall in my network.
Need to port forward certain ports for one computer but need UPnP for 2 different ps3's.These are the parts I have. I have read that the GT704WGB does not have a true bridge mode. I don't want to bias anyone however. How to best use this equipment so that I can port forward ports on my laptop. There are also several laptops, desktop and phones on my network but the 2 ps3's and my laptop are what primarily concern me.
-Actiontec GT704WGB for Verizon DSL (Modem / Router Combo) -Actiontec Support GT704WGB Wireless DSL Gateway for Verizon High Speed Internet access
Cisco Linksys wrt54gs v4 (Router) currently running Tomato firmware but I can flash dd-wrt back to it in a second.
I need to forward several ports. however it has been complicated by a missing or corrupt default access gateway. [code] I am leaving for quite a while tonight, hoping to come back to a reply I am using a belkin router ( will get model number and stuff later - not sure if its needed ) * and wow cable and internet url...
I have a DSL modem, model AG10W. I can't seem to figure out how to forward ports to xbox. No one seems to have this router/modem. I got it from a company here in town. I don't know much about this type of stuff.
I'm preparing myself for CCNA exam and i started doing a lot of different examples. I've got problem with Packet Tracer when i'm trying to apply some security settings for the range of switch ports in default VLAN 1. I might just demonstrate my commands so it will be easier do understand.
Using CCP I am trying to create a NAT entry for a range of ports. CCP window for a new NAT has only one entry for the port #. Is it possible to set uf port ranges in 877 router?
I've an ASA 5505 as my gateway for my internet at home. I've one public IP, so I use Port Address translatetion for my internal clients.
Now i wanna setup a FTP server, on a internal client. I will use Filezilla FTP server. I'm running the FTP server in passive mode, since the FTP server would be behind my ASA firewall/nat device.
I need 50 ports for the passive mode to be running.
I will use port range 50000-50050. I can easy make a firewall rule (access-list) that permit that port range.
But how do I PAT(NAT) a port-range on the ASA device? I can only figure out how to NAT one port at the time.
I have a network with multiple servers behind a PIX with 6.3 on it. I have one public IP address, and I'm using NAT. I'm currently trying to port my Exchange server to a cloud host, and the vendor is requiring I open up a wide range of ports for MAPI, basically ports 1024 on. What would be the command to forward all of the trafic cominto/from that broad range? if I could simply route all trafic to and from their two IP addresses to my email server, that would accomplish the same end goal.
