I need to forward several ports. however it has been complicated by a missing or corrupt default access gateway. [code] I am leaving for quite a while tonight, hoping to come back to a reply I am using a belkin router ( will get model number and stuff later - not sure if its needed ) * and wow cable and internet url...
View 8 RepliesI have a pocket wifi which allows you to connect up to five devices. my mum, sister and my phone can access it no problems but my laptop wont work.what will happen is:
- it connects automatically to the wifi
- but it has a little error mark on it
- and it says theres no internet access.
ive tried everything, ive ran several windows network diagnostics and it says the problem is the default gateway being unavailable.
I am having connection issues with my laptop involving my wireless adapter (I assume), since I am able to connect to the internet via a different laptop, Xbox and phones in the household. It is a Dell M5010 and the problem has only recently occurred.
View 9 Replies View RelatedI am trying to set up a PPTP VPN connection which also provides internet access. I have the following configuration. The router named "Router1" connects 2 computers PC1 and PC2 on the LAN side with a network address of 192.168.1.0/24. It is a PPTP server and a DHCP server. It gives IP addresses to PC1 and PC2. It has a static address of 192.169.1.2 on the LAN side and a static address of 10.2.9.1 on the WAN Side. PC3 has a static address of 10.2.9.2 and is connected to the WAN port of Router1. "Router2" is connected to the LAN side of Router1 and it has a static IP of 192.168.1.1. Router2 is connected to the internet and provides internet connection to PC1 and PC2. PC1 and PC2 connects fine to the internet and can see each other. However, PC3 cannot connect to the internet even though it is connected to Router1 by PPTP VPN connection. PC3 can see PC1, PC2, Router1 and Router2 but it cannot connect to the internet because Router1 does not give it the default gateway(192.168.1.1) to connect it. When PC3 connects via PPTP, It receives a correct IP address(10.2.9.3), correct DNS addresses but the ip4 default gateway field is left blank, and the DHCP option is not enabled on connection properties of PC3. Router1 is a DD-WRT firmware router (DLink Dir 400) and has PPTP server enabled as a service. How do I get Router 1 to give PC3 a default gateway IP? And how do I forward all outgoing packets from Router 1 to Router 2? I do not need port forwarding for some ports, I need full access to the internet from PC3 though the PPTP connection via Router2.
View 3 Replies View RelatedI just switched internet providers and i have wireless, since then, my boyfriends laptop is having problems staying connected to the internet. the desktop and my laptop stay connected his doesnt. it will say connected or limited access but i cant get a webpage or when i do its internet explorer cannot find page.System Info Utility version 1.0.0.1[CODE]
View 14 Replies View Relatedi am using a tp link 8817 modem, i can go online normaly but i can not access the default gateway (192.168.1.1, i check it in cmd/ipconfig) it keeps asking me username and password, althought i filled them with the correct username and password.
View 2 Replies View RelatedI am trying to set up a PPTP VPN connection which also provides internet access. I have the following configuration. The router named "Router1" connects 2 computers PC1 and PC2 on the LAN side with a network address of 192.168.1.0/24. It is a PPTP server and a DHCP server. It gives IP addresses to PC1 and PC2. It has a static address of 192.169.1.2 on the LAN side and a static address of 10.2.9.1 on the WAN Side. PC3 has a static address of 10.2.9.2 and is connected to the WAN port of Router1. "Router2" is connected to the LAN side of Router1 and it has a static IP of 192.168.1.1. Router2 is connected to the internet and provides internet connection to PC1 and PC2. PC1 and PC2 connects fine to the internet and can see each other. However, PC3 cannot connect to the internet even though it is connected to Router1 by PPTP VPN connection. PC3 can see PC1, PC2, Router1 and Router2 but it cannot connect to the internet because Router1 does not give it the default gateway(192.168.1.1) to connect it.
When PC3 connects via PPTP, It receives a correct IP address(10.2.9.3), correct DNS addresses but the ip4 default gateway field is left blank, and the DHCP option is not enabled on connection properties of PC3. Router1 is a DD-WRT firmware router (DLink Dir 400) and has PPTP server enabled as a service. How do I get Router 1 to give PC3 a default gateway IP? And how do I forward all outgoing packets from Router 1 to Router 2? I do not need portforwarding for some ports, I need full access to the internet from PC3 though the PPTP connection via Router2
ASA 8.3(2) 5505
I've configured a number of remote access vpns on ASAs, but I don't recall having a default gateway setting assigned after logging in.
Is there a way to disable the assignment of a default gateway upon login?
The value assigned is meaningless. It's just the next available address in the local pool.
I am using a WRT310N. I have a Cisco ASA5505 as my firewall and don't need the routing capabilities of the WRT310N. So I just plug the LAN port on the WRT310N directly to my LAN switch. I just need the WRT310N to have an IP address for management. So I configure the LAN with an IP address, but there is no way to set the default gateway on the LAN. You can only set the default gateway on the WAN interface, which I don't use, since I am using this in an AP only type of configuration.
View 1 Replies View RelatedI have my E1200 connected to my Netgear FVS318 router (which is a wired router) and the Netgear is connected to the internet.When a wireless client attempts to connect to the internet after automatically receiving an IP from the E1200, they do not have internet access as the default gateway that gets assigned is the IP of the E1200 192.168.2.100, which is not correct. It should be assigned 192.168.2.1, which is the IP of the Netgear router. Thefore, I have to manually set their IP addresses to use 192.168.2.1. How do you configure the E1200 to assign the correct Default Gateway IP to wireless clients who want to use DHCP?
View 4 Replies View RelatedI had a DI 604 router and I couldn't forward ports, someone told me to buy a new router because my modem (TM602G) doesn't have a built-in router and can't be blocking it so I bought a DIR 601 with wireless and I still have the problem.I don't have any firewalls.
View 19 Replies View RelatedIve been having trouble opening any ports on my windows 7 desktop. I connect wirelessly to my D-link Dir 655. I've tried port forwarding single ports to a static ip, but that didnt work either. I currently have the dmz server enabled and still no ports are open according to this port checker Open Port Check Tool - Test Port Forwarding on Your Router I have the windows firewall service disabled, upnp is enabled on my computer and router, i have spi firewall disabled, qos is disabled, and endpoint tcp/udp filtering on endpoint independent.
View 3 Replies View RelatedI'm trying to open ports 2934 and 2935 UDP on my Linksys E1000 router in order to play Falcon 4: Allied Force multiplayer but it's not working.I've correctly created a static IP, and logged in to the E1000's page. Under "Applications & Gaming", and then under "Port Range Forwarding" I entered values thus:
[code]....
I cannot successfully forward ports on this router, I've tried a few things but I can only assume the firmware is bad. I've already looked around for a solution but everyone says they solved it by just getting a different router (which at the moment isn't an option).
View 3 Replies View RelatedI can't get port forwarding to work, even when I turn off the Windows 7 firewall and AVG anti-virus software I'm running. I entered the IP address of my laptop (with a DHCP reservation) and UDP and TCP port numbers, with Schedule set to Always and Inbound Filter set to Allow All. That should be it, right? However, when I check the ports using PFPortChecker, both the UDP and TCP ports are blocked. I do have a Linksys wireless router daisy-chained to the D-Link router, but I'm not communicating on this computer through the Linksys router and the problem still occurs even when the other router is disconnected, so that doesn't appear to have anything to do with the problem. I just updated to the latest firmware (3.13NA).
View 11 Replies View Relatedhow to forward ports using routers
View 2 Replies View RelatedI went out and upgraded to the E3200 a week or so ago and since then i've been unable to forward any ports. I've tried pretty much everything I can think of: disabling Windows firewall, setting a static IP for my computer, setting a static IP for the router, enabling forwarding in both single and range menus, DMZ etc.Here is a screenshot of the port forwarding page just to confirm that i'm doing nothing wrong:In the above photo you will see that I set the computers static ip to x.1.2 and I later changed it to a value that was within DHCP range as listed on the status page of the router admin gui and it still didn't work.So, what I ask of you guys is if you can think of anything that I must be fundamentally doing wrong in order for this not to work. Could it be that i'm missing some possible drivers or network utilities on the computer i'm trying to forward ports too
View 1 Replies View RelatedI've just bought a Cisco 887m-k9 and I am trying to forward the ports. I have a Polycom HDX H.323 device connected to it with a static IP of 10.10.10.5 (ethernet port 0).Previously I had a consumer grade Linksys router which worked fine (I simply entered ports into the GUI), but I couldn't hardcode LAN port speed so I bought this. I have the list of TCP and UDP ports which are forwarded using the following commands:
ip nat pool Polycom 10.10.10.5 10.10.10.5 netmask 255.255.255.0 type rotary
ip nat inside source static tcp 10.10.10.5 80 88.xxx.xxx.49 80 extendable
ip nat inside source static tcp 10.10.10.5 443 88.xxx.xxx.49 443 extendable
ip nat inside source static tcp 10.10.10.5 1300 88.xxx.xxx.49 1300 extendable
[code]....
Where 88.xx.xx.49 is my static IP, while 77.xx.xx.170 is my default gateway.
Need to port forward certain ports for one computer but need UPnP for 2 different ps3's.These are the parts I have. I have read that the GT704WGB does not have a true bridge mode. I don't want to bias anyone however. How to best use this equipment so that I can port forward ports on my laptop. There are also several laptops, desktop and phones on my network but the 2 ps3's and my laptop are what primarily concern me.
-Actiontec GT704WGB for Verizon DSL (Modem / Router Combo)
-Actiontec Support GT704WGB Wireless DSL Gateway for Verizon High Speed Internet access
Cisco Linksys wrt54gs v4 (Router) currently running Tomato firmware but I can flash dd-wrt back to it in a second.
I am attempting to forward port 25565 on my router, and having some trouble. I've set a static IP address as both 192.168.2.10 and 192.168.2.111, and attempted a dynamic IP address. The port forwarding page via 192.168.2.1 in the browser looks like this, with the Private IP Adress changed to whatever corresponding IP address I have set (checked with cmd /ipconfig).
After testing with multiple online port checking tools, the ports remain closed.
We're trying to get a remote access setup for someone who needs to have access from offsite. To make things easy we set it up with a virtual machine running Windows 7 and RDP. Because the "other end" isn't our computer and we've had some difficulties with people using the Cisco VPN client successfully, we were just going to set up a machine as a RDP Gateway and forward the port through the firewall (WebVPN might be nice, but the plugins only do RDP through v5.x). I've tried this on 8.4-1 and after reinstalling the latest 8.2, and supposedly the NAT works and there is a firewall rule allowing access from the outside to the RD-GW server on HTTPS, but the ASA is still blocking those packets. I've looked at 4 howtos and followed them, trying from the console and from ADSM (and one trashed the whole setup, probably related to the reinstall of 8.2) - [code]
View 4 Replies View RelatedI have a router 1802 with a several vlans with IP 192.168.x.0/24 for each vlan (x, it meaning 1, 2, 3, 4, etc.).Now I need that an IP address outside from my network (this IP it is always the same) to be access to on particular machine that is in a private network (192.168.3.0/24) through a several ports:
25 (TCP,UDP), 80 (TCP,UDP), 554 (TCP,UDP), 2000 (TCP,UDP), 10002 (TCP,UDP), 10000 (TCP,UDP), 3000 (TCP,UDP), 3041 (TCP,UDP)
How can I do it?
Outside PC ---------Internet ----MyRouter -----MyParticularPC
83.240.194.99 193.136.80.1 192.168.3.1
I am trying to forward both TCP and UDP ports 3074 but it looks like I can only have either TCP/3074 or UDP/3074 open one at a time. When I try to enter the UDP/3074 NAT statement, I get "ERROR: NAT unable to reserve ports". [code]
View 4 Replies View RelatedI need to forward some ports for remote desktop and remote outlook which I host on an internal server. I have looked all over the web and got close, but no hints on how to do it in the asa 8.2. there is an 8.3 guide, but it is just different enough to not work. I am new to this device and cli.
View 3 Replies View RelatedHow do I forward ports on the N600 DB F9K1102v3? I have looked through everything. When I go to port forward, I enter the info and have it all down correctly, I click save and once it reloads it isn't there and the port isn't forward.
View 1 Replies View RelatedI am new to the RV180W. I am running the most recent firmware--version 1.0.1.9.
I am having trouble getting FTP to work with my QNAP NAS.
QNAP indicates that I should forward ports 55536-56559 to my NAS. I created a custom service to accomplish this, and then, under port forwarding, I selected the service and forwarded it to the private IP that corresponds with the NAS.
However, the port forwarding configuration only allows me to specify *ONE* internal port. With other routers I have always specified the same private port *RANGE* that corresponds with the public ports that I have opened up.
I'm trying to forward ports for SQL and VNC using these commands in the CLI:
ip nat inside source static tcp 192.168.1.150 5900 interface GigabitEthernet0 5900
ip nat inside source static tcp 192.168.1.150 5800 interface GigabitEthernet0 5800
ip nat inside source static tcp 192.168.1.150 1433 interface GigabitEthernet0 1433
where 192.168.1.150 is my server (that hosts SQL server and that I want to be able to connect to remotely using VNC) and GigabitEthernet0 is my configured WAN interface.
When I try to connect from an external client I get the error: "Failed to connect to server..." Is this a firewall issue? How do I get round it? The 819 is the only router/firewall in my network.
I have an ASA 5505 running 8.4(1), and I'm configuring it with ASDM 6.4(1). The outside interface is configured with a single static address. I have a few services port forwarded sucessfully to three different servers on the inside network.
I need to make a media proxy on a SIP server available to the outside. It requires a large range of forwarded UDP ports for the media channels.
I tried adding a network object NAT rule like the others I'm already using to forward HTTP and RDP. I entered a range of ports for the real port and the mapped port using the syntax 60000-60999. ASDM accepted it, but the NAT rule list displays "Any" in the service column. When I apply the change, I get the following error:
nat (inside,outside) static interface service tcp 60000-60999 60000-60999
^
ERROR: % Invalid input detected at '^' marker.
How do I forward a large range of UDP ports from the outside interface to a single server on my inside network? I'd like to use ASDM, but I can switch to the CLI if that works better.
I have a DSL modem, model AG10W. I can't seem to figure out how to forward ports to xbox. No one seems to have this router/modem. I got it from a company here in town. I don't know much about this type of stuff.
View 1 Replies View RelatedA client is thinking of putting in a srp527w. they get assigned a static ip on the adsl interface (165.228.204.x), and then have been assigned another block(203.39.183.x/29).how can i have it so that i am able to forward individual ports from the external ip's, to selected internal ip's.
View 1 Replies View Relatedi've a cisco asa5505 on adam 6.4 and a dvr i would like to forward the ports 9000 and 85 in order to monitor the dvr from outside?
View 1 Replies View Relatedi joined because i keep on having the same problem. i read around the forum a bit before joining and i saw that mcafee was causing the problem for a lot of people. i dont have mcafee so that cant be it several crashes per day. like, literally close to 100 of them.
View 3 Replies View RelatedPeriodically, I drop internet everywhere around my college's campus. I'm literally four feet from a router, but it doesn't seem to matter. I'll disconnect, run troubleshooter, and I'll get the error message saying that the default gateway is not available. My college is designed for Macs, but I'm running Windows 7. My Mac colleagues do not experience problems. The computer works at home and at nearly every other wireless network I've brought it in range of. Specifically, either IBM or Dell.
Dell XPS 15
i7-2720QM
8gb Ram
Windows 7 Home Premium SP 1
540? Something around 500 Nvidia graphics card
Ipconfig results:
Windows IP Configuration
Host Name . . . . . . . . . . . . : George-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
[code].....