I have the problem that the AP1130 can not join to WLC2504.
Console Messages of AP1130:
*Aug 14 09:34:54.029: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Aug 14 09:34:54.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.x.251 peer_port: 5246
[Code].....
I have WLC 2504 and AP3502I . AP can not join wireless controller .
*May 24 16:33:51.871: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*May 24 16:33:51.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 10.80.90.99 peer_port: 5246
[code].....
I find much document, but not found information about whether those support for IPv6 e.g. dual-stack like newer series.
View 3 Replies View RelatedI just received a Cisco Aironet 1130 AG wi-fi router to configure and when I entered the router through console, I am not able to get into config mode. It says:
[code]....
My wireless users are loosing the internet(http and https) connection many times per day. I just check the ports configuration in the switch, but The problem persist. The device is a Cisco Aironet 1130 AG.
View 4 Replies View RelatedWe have a Cisco Aironet 1130AG Wireless AP (firmware 12.4) and have a guest wireless network (internet only) and corporate wireless network configured on it. They are kept separate by having different VLANs assigned to them. When a laptop connects to the guest network I see the DHCP request go out and it is tagged with the correct VLAN. The problem is when a laptop connects to the corporate network I see the DHCP request go out but there is no VLAN tagged on the packets. This causes a problem because both of our DHCP servers (on VLAN 1 and 3, remote DHCP servers no DHCP running on the Aironet [Doesn't seem like this version has a DHCP server]) are sending responses and sometimes the corporate user will get an IP address on the Guest subnet.
Our corporate network is setup on VLAN 1 which is configured as the Native VLAN on the Aironet. Will this cause the Aironet not to tag these packets with any VLAN information? Any other thoughts as to why it isn’t tagging these packets to a VLAN?
I need to configure SNMP on our company Aironet 1130. I am told there is a tool we can use that will allow us do the configuration from a PC vs connecting directly to the device.. If that is true, where can I download it?
View 5 Replies View RelatedWhen I check the AP join statistics I see the following: Reason For Last Unsuccessful Attempt RADIUS authorization is pending for the AP, I don't run a radius server and don't know how to get around this so that the device can join.
View 4 Replies View Relatedmy access point 1230 fail to join the controller. The image is C1200-k9w7-mx.123-8.JA2. I tried to reboot it but it does not join to controller. How do I initiate the discovery process again to make this AP to join? Should I convert it back to autonomous AP and then LWAPP process again? I can ping the AP from the controller and the AP is in the same VLAN with controller.
View 3 Replies View Relatedupgrading 300 Aironet 1100 series i.e. 1121 to newly bought WLC.Problem is 1100 are using SSC cert that I must do " debug pm pki enable " on each of 300 AP upgrading to extract its key-hash then copy to Security>AAA>AP Policy and repeat for 300 times. It is the impossible task.What would you recommend us to do the any other methods to achive the same goal?
View 2 Replies View RelatedI have CISCO Aironet access point C1130 , but not able to connect by users, I can see below logs from access point.
Jun 13 17:50:10.686: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:10.686: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:15.678: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:15.678: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
[Code] .....
I just received a Cisco Aironet 1130 AG wi-fi router to configure and when I entered the router through console, I am not able to get into config mode. It says:
AP588d.09a7.93e4#conf t
^
% Invalid input detected at '^' marker.
Also,
AP588d.09a7.93e4#sh start
startup-config is not present
Also, this is what I see in my flash:
AP588d.09a7.93e4#sh flash:
Directory of flash:/
3 -rwx 217 Mar 01 2002 00:07:10 +00:00 env_vars
4 drwx 128 Jan 01 1970 00:02:03 +00:00 c1130-rcvk9w8-mx.bin
I need to configure this device and set up for wi-fi access in my organisation network.
We have an aironet 1130ag in a remote office connected to the data centre over MPLS. The Radius server is based on server 2003.We have hundreds of these points set up exactly the same but this is the only one giving me issues, I even stripped the config and rebuilt it and then swapped with a new access point
The issue is that clients can't authenticate when connecting to the access point but provides nothing in event viewer. Checking the RADIUs server provides nothing either.The access point error logs just state station: authentication failed
On looking deeper into the problem I enabled RADIUS debugging on the access point and got some interesting results, in particular is the line:
no sg in radius-timers: ctx 0x12EF0A4 sg 0x0000.I can't find out what no SG in Radius-timers actually means, but after that line appears I just see more retransmits and no sg fails.
I inspected the packets on the RADIUs server and found lots access requests coming from my access point and lots of access-challenges returning back from my RADIUS server - I'm not sure how often that's supposed to happen or if it's a one time occurance. I did however see directly after the first access-request that the RADIUS server returns with UDP and is fragmented, length is 1514...... could this be the problem? If so why cannot it hanlde fragmented packets?
I convert IOS Cisco AP 1130 LAP to 1130 Autonomous mode. Well, the periphericals - clients connect to SSID AP no recieved I.P Adress, I think that is not possible active option DHCP server in AP 1130 dispositive. In mode I.P static clients the connection is established successfully.
View 1 Replies View Relatedhow to change our wireless setup. Currently, we have 2 Cisco AiroNet 1130 WAP's in the office that go directly into the 2 POE ports on our Cisco ASA 5500. These WAP's have 1 SSID and are using WEP for security. After demonstrating the flaws of WEP to my boss, he has agreed that we should use something more secure and I've suggested WPA. We want visitors to our office to be able to hop on our wireless but on a separate guest SSID with WEP.
I'd like the internal SSID to route to the ASA and take the default route to the internet (it will be our new fiber connection once it's installed in a couple weeks). The default route is whichever connection is working since our ASA 5500 will fail over when it detects an outage.
I'd like the guest SSID to route to the ASA and then go over our existing cable connection. This connection will be our backup once the fiber connection is installed. Since we won't be using it very often, but will be paying for it, I advised that we send all guest wireless traffic over this connection since 50/5 is plenty for guests.
The current SSID (which will be the internal SSID) has no VLAN. We do currently have a few VLANS on our network, one for voice (.42) and one for data (.100) and the default (.0). What device to I create the VLAN on (Cisco 5500?) and how to I setup the WAP? I need very basic instructions to start and I'm also trying to do this without causing downtime if possible.
I've attached a diagram of what it should look like. Red indicates our internal network and Blue indicates the guest network. I can send screenshots as well.
I need urgent support on creating SSID as layer 2.We have cisco WLC2504 and 1602i access point. In our network we have in gate for guest.I want to create one ssid and bind with vlan only. We can not creat interface on WLC b/c of static IP.
View 3 Replies View RelatedI have two Wireless LAN Controllers 2504 and 8 APs 3502e. The WLCs are running software version 7.0.116.0. The problem is that I don't have the mesh option to configure indoor mesh inside the controller. In chapter 9 of Wireless LAN Controller Configuration Guide, Release 7.0.116.0 says that I have to go to Wireless Menu and select the AP. When I am inside the AP general page, the guide says I have to go to the Mesh tab, but that tab doesn't appear in the controller GUI. Do I have to use another image in the controller? Or do you have to use an special mesh code or something like that? Because in the download page of the controller it only appears the 7.0.116.0, two more new versions but there is nothing about mesh image.
View 5 Replies View Related1) We have client setup, which has all PCs in Workkgroup , client has network sharing enable in LAN . Its work well in LAN , he don't have Local DNS , still he is able to ping or access sharing using device hostname
2) When Client moves into Wireless , he is not able to ping or access sharing using Hostname , but if used the ip details he is able to ping and do sharing using IP address onlye.
My Wireless Setup has WLC2504 and LWAPP Access Points.
I am having issue with integrating WLC2504 with Win2k8 server NSP radius server.
View 3 Replies View RelatedI have few question with WLC 2504 with 25 License AP. Our customer have SSID around 30 SSID then, is it possible to create WLAN around 30 SSID on WLC 2504? becuase i had tried to do it on WLC4404-25 License that can do or create WLAN with 30 SSID.
View 12 Replies View Relatedconfigured Cisco 2504 WLC with 1142 Aps... Guest wireless works fine
for the staff wireless I wanted to authenticate with 802.1x & Radius. So configured an external Radius server (Imprivata) and configured the 2504 Radius options for the extenal server.( Layer 2: WPA2-AES & Auth Key Mgmt: 802.1x )
When I connect a client to this wireless, the authentication fails, I wonder whether it is because of the client side settings..
Which trusted Root Certification Authorities need to be checked?
Every time I power down my WLC2504 controller and then back up, the time reverts back to the year 2000.The APs can't join the controller, due to certificate errors, until I reset the clock. This problem just started recently.
View 6 Replies View Relatedhow can i replace my wlc2504 to a WLC5508 without disconnecting everybody, i have 3 SSID, on different VLAN.. I want the WLC5508 to be the main WLC, so i can remove the 2504 from the network. On the WLC5508, it will be the same configuration of the 2504. Is there a procedure or a wiki on such operation?
View 8 Replies View RelatedCan we change the internal web authentication for guest network to use http instead of https?
View 3 Replies View RelatedI know what the problemis i need to tell the AP what the mac of the switchport is but i can not figure it out because it is a CATos Switch?on a IOS I would just use the Show interface command and use the bia but i dont know how to figure out the bia on a CATos?
View 3 Replies View RelatedI've set up a WLC2504 with interface "mgmt" and "guest" (2 different VLAN IDs) both configured on port1.Now I'd like to be able to connect to PoE ports (port 3 and 4) 2 LAPs which should be able to get IP addresses from the DHCP as if they were connected to port1.
View 14 Replies View Relatedwhat is the reason that cisco 1130 series ap cannot be seen by switch it connected to, by CDP protocol
View 2 Replies View RelatedI've got this weird problem with my AP. It keeps rebooting randomly. It happen to all the AP in my campus randomly. It happens recently. It have been commission for quite a long time. ie user able to connect and use it. its connect back to the controller to back in another campus. Below are the logs i gather.
*Jun 7 11:13:54.287: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Jun 7 11:13:54.290: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
[Code]......
Why it could be that switch cannot see Cisco ap 1130 series by cdp .
View 1 Replies View RelatedAny info on successfully resetting an light weight 1130 AP to the factory settings? I tried the method described in the doc for 1130 on how to reset 1130 AP to the default settings, but it was not successful. I tried shutdown the AP, and plug in the power while press and holding the Mode button for about 3 seconds.This AP has lost it association with the WLC, is there anyway i can reset the AP to factory default and put in the correct IP address again?
View 3 Replies View RelatedLooking to set up a small office cheaply and quickly and was thinking about ordering a 2006 and some 1130s off EBay. Are the lightWeight 1130s compatible with the 2006?
View 9 Replies View RelatedIOS of my access point 1130 was deleted after bad manipulation. I have just a boot but not a flash on my AP. I can connect it just in console mode. What is the procedure to restore the IOS?
View 2 Replies View RelatedWhen is 1130 AP going eos/eol? I have tried searching, but could just find eos/eol for 1130 power supply and not for the AP itself.
View 6 Replies View Related
