What so you think as an access point hardwired to a WNDR3700v2?Buffalo WCR-GN AirStation N-Technology Wireless-N150 Router & Access Point - 150Mbps, RJ-45, 2412 - 2462 MHz, 4x LAN Ports, WAN, Wireless-N, WE
View 3 RepliesI have 4 DAP-1522's bridging to a WNDR3700v2. Any device plugged into any of the 1522's can access the internet and can access shared drives etc. on any other device plugged into any 1522. I can access the WNDR3700 admin website from a device connected to a 1522.
However, no device plugged into a 1522 can access a device plugged into the 3700's ethernet switch. Likewise, the devices plugged into the 3700 cannot access devices plugged into 1522s.
Devices plugged into the 3700's switch can access the internet and can access each other.
I have changed network cables, power cycled all devices (PCs, bridges, routers, etc) at least once. I am running latest firmware on 1522's and 3700. In short, I've tried just about all the basic stuff.
It almost appears that the 3700's switch is acting as an isolated network. I would say that were true, except that I can access the router admin page from anywhere (any 1522 and directly connected to the 3700).
All devices are within the 10.0.0.x address range with a subnet mask of 255.255.255.0. Again, I have no problems accessing the internet. Just the problem of devices plugged into a 1522 communicating with devices plugged into the 3700 and vice versa.
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedHow would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedHow do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedI am about to get a group of 5 public (external) IP addresses from my ISP. I have a Netgear WNDR3700v2 router. I was told that 1:1 NAT would be the way to assign static public IP addresses to some of my computers, while making the rest use private network IP addresses (issued by a DHCP server), and have all the computers accessible in the same domain network.
Is this possible using my netgear WNDR3700v2 router? If not, what do I need?I was looking at the Netgear FVS318G wired router, and I would then use my existing router as an access point. Does this make sense?
SETUP CD MISSING - NETGEAR WNDR3700v2Have just received excellent condition 'barely-used' WNDR3700v2 router with ac adaptor, but NO setup cd. Am I dead in the water, as Netgear doesn't provide replacement CD's, or is there a workaround using say, an early firmware upgrade? Or other?
View 2 Replies View RelatedI had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedI have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedHave a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedI have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View RelatedI've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
connecting my old laptop to my router (Netgear WNDR3700v2) The router is an N router but is backwards compatible, but my laptop can't find it. The laptop is an LG LE50-5273V. I looked into the device manager and found two network adapters; 802.11b/g wireless adapter and Marvell Yukon 88E8036 PCI-E Fast Ethernet Controller. So it should be able to connect to it? Besides from that laptop I have another PC connected to the router and it works (Using N), Will I then be able to combine both N with B/G?
View 2 Replies View RelatedWhat I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies View RelatedI'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
Is it possible to configure WRT120n as an access point?
View 1 Replies View RelatedI have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies View RelatedI have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies View RelatedCannot access configuration page for WAP11 Access
View 9 Replies View RelatedWhen I plug my laptop up to our modem, all i get is local access. IPconfig gives me to default gateway or dns suffix. Naturally there is no wireless. My roomates laptop runs fine wired or not and we have the same set up.Not sure what to do.
View 12 Replies View Relatedhave a dell inspiron 1545 with windows vista. Sometimes at coffee shops I cannot connect to the internet. It says that I have local access only. This also has happened when I use my hardwire internet connection. Then at times it does work on the same network. It is not a network problem as I can connect with my iphone or other devices.
View 14 Replies View RelatedI have a friend whose Dell Latitude D800 and has been able to connect to the internet wirelessly using a Net Gear wireless adaptor.Comcast cable came several days ago to set them up to connect to the internet using their cable modem. The modem is working fine and packets are sent out but there is no internet connection and no packets received.
View 2 Replies View RelatedI have wifi laptop that I want to use for video to tv but obviously only using about half of download speed of hardwired desktop pc. Can I use ethernet cable hardwired on laptop while it is wifi or will this interfere with connection?
View 2 Replies View Relatedi really don't get it what caused this. There was a problem from the provider.. then this .. I resetted the router, could get to the Interface.. and now i can't And besides that, the internet connection get's picky to what lets work For example i could use gmail .. but not this page.. or instant messaging worked, but not browsing (and the speed was awful)
at the moment the connection seems stable though (the changes from above were made)
I was told that i need to disconnect from my wireless and hard-wire the connection directly from my modem. My wireless connection is downstairs in the basement. Do i need to call a professional to do this or is this something i can do from home?
View 1 Replies View RelatedWe run a Cisco WRT160N router. It works fine wireless. We are having issues connecting through our desktop which is hardwired. If i click ok about 3 or 4 times after it tells me it cannot find the site it works.
View 1 Replies View Relateddoes my router have to be hardwired into my modem in order for my router/ computer setup which is located one room over from the cable modem
View 1 Replies View RelatedI've been running a small home network with no problems for the last year. I'm unsuccessfully attempting to add a wired connection in my basement, but the laptops do not recognize the connection. I've tried laptops running Vista and WinXP -- neither works.
The attached graphic depicts the current state of the network and also identifies the problem connections. At first I thought my new CAT-5 cables were the problem, but I've ruled that out by swapping the cable from my desktop (hardwired to the wireless router) to the laptop.
I've also pasted the IPCONFIG text from the desktop pictured in the attachment. Is there any obvious reason that setup this isn't working??
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersMark>ipconfig/all
[Code]....
I cannot see my synology NAS from my WDTV Live players (or PS3 or Samsung TV) when the NAS connected directly to one of the 4 GbE ports on the 655 using media server (DLNA) protocol. I've moved the NAS to another location on my network and not directly connected to the 655 and all the other media players see it except for the WD that's connected to one of the ports on the back of the 655. As a work-around, I have set the WD player that's connected to the 655 to use network shares instead of DLNA and this seems to work fine. So, there must be something that the 655 is doing wrt the DLNA protocal that is blocking communications.I have the 655 configured as an access point and have turned off DHCP and every other function that could be causing any issues. I've turned UPNP on and off to see if it resolves the problem, and although it seems to have some bearing on the problem, the issue persists. I also have a DIR-645 also configured as an access point (not connected to the 655) and have the synology NAS connected directly to it and it works just fine. All media players can see the NAS except for the one that's connected to the 655.I've been having this issue for some time now and have worked around it by moving the 655 so it wouldn't be an issue. However, I needed the wireless and gigabit switch capability upstairs and am battling this issue once again. I'd really like to keep the 655 and get this working, but it seems as the 655 is the culprit here.
View 5 Replies View RelatedSetup N600 DB as an access point using the most recent firmware,3.03.12? Once I do I'm not able to access the dashboard even through I enabled the remote management option.
View 2 Replies View RelatedI have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.