Additional Hardwired Connections Not Detected?
Apr 29, 2012
I've been running a small home network with no problems for the last year. I'm unsuccessfully attempting to add a wired connection in my basement, but the laptops do not recognize the connection. I've tried laptops running Vista and WinXP -- neither works.
The attached graphic depicts the current state of the network and also identifies the problem connections. At first I thought my new CAT-5 cables were the problem, but I've ruled that out by swapping the cable from my desktop (hardwired to the wireless router) to the laptop.
I've also pasted the IPCONFIG text from the desktop pictured in the attachment. Is there any obvious reason that setup this isn't working??
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersMark>ipconfig/all
[Code]....
View 9 Replies
ADVERTISEMENT
Dec 29, 2011
In my main office, I have a cable modem which is connected to my main E4200 router. All of my equipment (except my Ooma) is served by the E4200. The E4200 broadcasts a wireless network.In my basement, I have a Wii / entertainment center. The E4200 signal from upstairs isn't strong enough to stream video.
I bought the WET610N and have successfully set it up to interact with the E4200 wirelss network. I can hardwire my laptop to the WET610N and verify the internet works greatHowever, the Wii must connect over wireless. I have other equipment in the basement which would benefit from an internet connection. So, I want to A) connect the ESXS88W 10/100 8-port workgroup switch I have to the WET610N *AND* also broadcast a wireless signal in my basement (assuming the wireless network I see in the basement is the same "old" one from upstairs which has not benefited from the WET610N).
How can I set up my WRT54G2 to broadcast a wireless signal in the basement so that it leverages the E4200 signal served by the WET610N, while also having the workgroup switch offer hardwired connections to my other equipment (like Dish Network receiver)? It doesn't seem to work by just plugging the WRT54G2 into the workgroup switch.
View 2 Replies
View Related
Jan 6, 2013
I've formatted my HP 530 Notebook (using 'Operating System CD - Windows XP Professional SP2'). All went well. It was my first format but I read a lot on the internet, so I knew I had to download and install the chipset, the bus driver, the audio and video drivers, the network adapters, etc. This I did, on the HP website [URL].
Everything is working perfectly except for the internet. The device (a Broadcom wireless network adapter I installed from the HP website) is reportedly 'working properly', the HP assistant says that the Wireless LAN is 'ON', but my Broadcom wireless network wizard cannot find any network, let alone the network of my router. The Windows assistant is just as useless.
I've tried it all: uninstalling and re-installing, snooping around with 'ipconfig /all' and utilities like 'Everest', to start the Wireless Zero Configuration, to use other network adapters, installing SPs and patches, all that jazz. Apparently, everything is fine and 'working properly' - except that there's no network in sight.
Clearing up some questions:
- The 'Everest' utility says that the Interface Type of my wireless network adapter is 'Ethernet'. Isn't Ethernet supposed to be for cable connections?
- Needless to say, I've been back and forth with drivers a lot. Windows calls my wireless (non)connection 'Wireless Network Connection 2'. Is this in any way significant?
- I'm using 'Broadcom' because that's all I saw at the HP website. Should I try something else instead, like Atheros or Intel something-something?
I'm becoming a bit desperate, so if all else fails, I'm willing to reformat the computer (for the third time) and install the drivers you recommend to me in the recommended order.
View 14 Replies
View Related
Jan 3, 2011
When I plug my laptop up to our modem, all i get is local access. IPconfig gives me to default gateway or dns suffix. Naturally there is no wireless. My roomates laptop runs fine wired or not and we have the same set up.Not sure what to do.
View 12 Replies
View Related
Jul 25, 2012
have a dell inspiron 1545 with windows vista. Sometimes at coffee shops I cannot connect to the internet. It says that I have local access only. This also has happened when I use my hardwire internet connection. Then at times it does work on the same network. It is not a network problem as I can connect with my iphone or other devices.
View 14 Replies
View Related
Apr 4, 2011
I have a friend whose Dell Latitude D800 and has been able to connect to the internet wirelessly using a Net Gear wireless adaptor.Comcast cable came several days ago to set them up to connect to the internet using their cable modem. The modem is working fine and packets are sent out but there is no internet connection and no packets received.
View 2 Replies
View Related
Feb 1, 2011
I have wifi laptop that I want to use for video to tv but obviously only using about half of download speed of hardwired desktop pc. Can I use ethernet cable hardwired on laptop while it is wifi or will this interfere with connection?
View 2 Replies
View Related
Apr 8, 2011
i really don't get it what caused this. There was a problem from the provider.. then this .. I resetted the router, could get to the Interface.. and now i can't And besides that, the internet connection get's picky to what lets work For example i could use gmail .. but not this page.. or instant messaging worked, but not browsing (and the speed was awful)
at the moment the connection seems stable though (the changes from above were made)
View 12 Replies
View Related
May 2, 2012
I was told that i need to disconnect from my wireless and hard-wire the connection directly from my modem. My wireless connection is downstairs in the basement. Do i need to call a professional to do this or is this something i can do from home?
View 1 Replies
View Related
Jun 10, 2012
We run a Cisco WRT160N router. It works fine wireless. We are having issues connecting through our desktop which is hardwired. If i click ok about 3 or 4 times after it tells me it cannot find the site it works.
View 1 Replies
View Related
Nov 24, 2011
does my router have to be hardwired into my modem in order for my router/ computer setup which is located one room over from the cable modem
View 1 Replies
View Related
Dec 9, 2012
What so you think as an access point hardwired to a WNDR3700v2?Buffalo WCR-GN AirStation N-Technology Wireless-N150 Router & Access Point - 150Mbps, RJ-45, 2412 - 2462 MHz, 4x LAN Ports, WAN, Wireless-N, WE
View 3 Replies
View Related
May 21, 2012
I cannot see my synology NAS from my WDTV Live players (or PS3 or Samsung TV) when the NAS connected directly to one of the 4 GbE ports on the 655 using media server (DLNA) protocol. I've moved the NAS to another location on my network and not directly connected to the 655 and all the other media players see it except for the WD that's connected to one of the ports on the back of the 655. As a work-around, I have set the WD player that's connected to the 655 to use network shares instead of DLNA and this seems to work fine. So, there must be something that the 655 is doing wrt the DLNA protocal that is blocking communications.I have the 655 configured as an access point and have turned off DHCP and every other function that could be causing any issues. I've turned UPNP on and off to see if it resolves the problem, and although it seems to have some bearing on the problem, the issue persists. I also have a DIR-645 also configured as an access point (not connected to the 655) and have the synology NAS connected directly to it and it works just fine. All media players can see the NAS except for the one that's connected to the 655.I've been having this issue for some time now and have worked around it by moving the 655 so it wouldn't be an issue. However, I needed the wireless and gigabit switch capability upstairs and am battling this issue once again. I'd really like to keep the 655 and get this working, but it seems as the 655 is the culprit here.
View 5 Replies
View Related
Jan 21, 2013
I can follow directions and am fairly tech-savvy, just don't have the time to troubleshoot this stuff and run my business. Here's the rundown:Router:Cisco Linksys E1000 V2
-working fine until I unplugged to move it and plugged it in
-verified with tech support the problem is not physical
-right now, am hardwired to the router, which is hardwired to the cable modem, and connectivity is fine through hardwiring
-no luck through wireless - this is the error message I get:
This webpage is not available:The server at www.google.com can't be found, because the DNS lookup failed. DNS is the network service that translates a website's name to its Internet address. This error is most often caused by having no connection to the Internet or a misconfigured network. It can also be caused by an unresponsive DNS server or a firewall preventing Google Chrome from accessing the network.
View 9 Replies
View Related
Mar 5, 2011
I have a laptop using a wireless Ralink USB card to connect to the internet. Is it possible to use the unoccupied Ethernet cable slot to hardwire into a router and use the router to send out the wireless signal picked up by the USB card to other devices?I know I shared my connection like this to my xbox 360 but wasn't sure if it could be used with a router.
View 1 Replies
View Related
Feb 12, 2013
I have a Linksys WR-110 wireless router that has been acting up lately. I have 10mbps cable internet and have my desktop computer hardwired to the router. I notice that after a few days the download speed gets down to the 2mbps range. Verified by { URL}. If you do a hard boot (unplug for 30 seconds) it will go back to 10mbps speed again. But it seems after a few days it slows own again.
I always run speed test to verify, and it always runs back up at advertised speeds once i hard boot.
Why would this be happening?
View 11 Replies
View Related
Jan 20, 2012
The Dell Laptop was working on wireless, now wont connect to internet, not even if hardwired to modem desktop, the wireless signal under laptop status reads 100%
View 3 Replies
View Related
Feb 19, 2012
I recently purchased a Linksys E1200 router. I have two desktops (Windows XP) hardwired into the router, one of which is not connecting at all.I have talked to Linksys tech support 3 times already and they have not been able to fix the problem. Pinging a website got a request timeout.Pinging the router got a good response.It was properly assigned an IP address, but did not connect through the router.Under Network Connections, it displays as "Connected" but is still not able to access the Internet.
View 2 Replies
View Related
May 18, 2012
How can I find my IP Address number on my wireless router. I'm trying to connect my blue-ray player for the Netflix.
View 1 Replies
View Related
Oct 19, 2011
DLink DIR655
H/W Ver B1
F/W Ver 2.00NA
I've configured my 655 and I can access the internet through it. Network cable from PC goes to the DLINK, DLINK to the DSL modem, DSL modem to the big scary internet. This all works great. Now for the Wi Fi.I've set up the Wi Fi on the 655 and can both see and connect to my newly configured home network from my laptop, but I can not access the internet from the laptop.
View 2 Replies
View Related
Jun 27, 2011
My roommate has a HP pavilion that she has been trying to connect to our internet, and while it seems to be connecting to the network, it wont connect to the internet.Its running Vista, and I tried all the repairs that it prompted me to try, but could not resolve the issue.I know it isn't a internet problem, because the desktop is hardwired and we have two xbox's that connect wireless with no problems.Im not sure what info I should have included in this thread, but its my first post and wasn't sure what I needed to put.
View 12 Replies
View Related
Nov 28, 2012
I have a win7 desktop upstairs with all of my media on it.I also have a winXP laptop that I would like to use as a media center running xbmc connected to my tv downstairs.I have set up a workgroup so my laptop can access the media stored on my desktop and everything works great when they are both hardwired to my router (Linksys E3000).However, as soon as I unplug my laptop from my router and switch to the wireless connection I can no longer ping my desktop or access the shared folder (internet still works fine on the laptop, it just cant see my desktop anymore).If I plug it back in to the router, everything works again.
The exact error message I get when I try to access the shared folder is "\INFINITYMedia is not accessable. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. [code]
View 14 Replies
View Related
Feb 7, 2011
I have just purchased a new ASUS Laptop for my wife.We are currently running two destop computers on a D LinK Router. How do I go about including the new computer on the network wirelessly?What do I need to purchase to make the transition easiest? The two desktops are running Windows XP Professional, the new system is Windows 7.
View 4 Replies
View Related
Jun 12, 2013
Without my N 450 router hooked up I am getting hardwired speeds of 50/5 mb, but with N 450 hardwired into my PC the speeds drop to 20/5 mb. I have checked DHCP and I am not getting piggy backed. Is it a bottlekneck, misconfigured or just not compatible with Time Warner?
View 1 Replies
View Related
Jul 2, 2011
I'm going to be moving into a place in the next couple months where I'll have to go wireless on my desktop (until now I've just done Ethernet so I don't even have a wifi card on my desktop). The router/modem aren't anywhere near my bedroom so my gear will be going wireless from now on All my devices are built-in wifi ready but not my desktop.
I would like recommendations as to a rock-solid, reliable, fast and well performing card as I can to make up for no hardwired connection. Especially with BF3 coming out I'm not all that thrilled with being forced into this situation but you gotta do what you gotta do. Anyhow, I'll be bringing my router (Netgear WNDR3700) so I'll have the range and speed from there about as good as I can get, so I'd like a card of equal merit.
One side note...probably not really feasible considering I want speed and performance as a priority, but I would love a card (if possible) without bullshit antennas sticking out of the case, or with external antennas you have to set up on your desk. I will go that route if I have to but man that is an aesthetic nightmare, IMO. The ones that stick out of the back of the case are the worst looking for me just as a caveat.
View 1 Replies
View Related
Apr 14, 2012
Im trying to optimize my E4200 settings and Ive noted that ping and download speeds are extremely slow for the internet service I signed up for. Ping speeds are consistently more than 1000ms and dowload speeds typically are less than 3Mbps. These are for both wireless and wired connections to the E4200 router.
When I disconnect the router and hardwire my laptop directly to the the modem, ping speeds are less than 100ms and download speeds are 20Mbps.
Simply put, webpage loading is at a snails pace with wireless and wired connection the router, but blazing fast when hardwired directly to the modem.
On a seperate issue, the iMac I have is also **bleep** slow even when hardwired directly to the modem. Is there an obvious router setting Im screwing up? Router is updated with the latest software.
View 3 Replies
View Related
Jul 5, 2011
Win7, wrt54gs,
It works sometimes. I imagine it has a noise problem since sharing files works, internet works. I cannot remember how to change channels on this router to save my life, though. What is special about sharing a printer?
View 1 Replies
View Related
Mar 31, 2011
my company has a 4mbps leased line from TTSL . we are getting 2 WAN IP and 2 LAN IP. in Addition we are also getting 12 additional IPs .-what is additional IP, their uses?-how are the 2 wan ips configured? & how they are distributed in network? -is 1 IP from the ISP sufficient if i have a 1:1 internet bandwidth connection?
View 9 Replies
View Related
Feb 23, 2013
Okey so the issue here is that my computer just looses its connection after ive downloaded somewhat or something.especially when im downloading from you know what So.when i try to go on my Chrome, explorer, firefox WHATEVER it says Additional logon information may be required.so i click on that annotation and it just brings me to the home page of my main browser google home page with ofcourse no internet what so ever.. im using Wireless and wired (best connection) for the wired i use it through a cisco but neither works.it works fine on laptop and my iPhone 4.
View 1 Replies
View Related
May 16, 2012
When I login to Facebook on my home computer it opens and trys to read something additional (the little activity circle continues to roatate) but it never completes, it is like it is in an endless loop so my browser (IE 9) locks up and I have to use task manager to terminate. I can get into facebook on my office computer with no problem. Also my wife has the same problem on her facebook account.
View 3 Replies
View Related
Feb 14, 2013
From where I will get additional driver to share windows 7 pc to windows xp users
View 1 Replies
View Related
Jan 18, 2012
I am in the process of deploying an additional Cisco 1142 AP into my network. I would like to set it up to be the same SSID as the first one, and be able to have laptops roam from AP to AP. I am simply trying to expand the current coverage of my wireless network. I have both APs mounted and access to both.
-CISCOAP01 - 192.168.2.2
-CISCOAP02 - 192.168.2.3
What do I need to do (configre) to make this happen? I am rather new with Cicso. I am using the web interface to setup the APs. The first one has been up and running for about a year now with no problems. [code]
View 2 Replies
View Related
Jul 28, 2012
Im wanting to add an additional module in to my Cisco 4500. Is as simple as plug and play or is there some commands that I need to add or anything I should be aware of.
View 2 Replies
View Related
