my company has a 4mbps leased line from TTSL . we are getting 2 WAN IP and 2 LAN IP. in Addition we are also getting 12 additional IPs .-what is additional IP, their uses?-how are the 2 wan ips configured? & how they are distributed in network? -is 1 IP from the ISP sufficient if i have a 1:1 internet bandwidth connection?
View 9 RepliesThe reason is i want to know the difference between the leased line and the DSL line. The whole thing behind the confusion is, We plan to have a high speed internet connection in our office. We will don't have a branch office or some thing like that. I preffered to have high speed internet in our office. I found in some website that Lease line will have high speed connectivity(Upto 10Gbps). Can i use the lease line or DSL is enough for our office. Our office contains of 82 user who will use internet.
View 2 Replies View RelatedI got following IP address from BSNL to configure Internet leased line.OFC cable was terminated at our premises. it has to connect Ethernet port.Say eg.Wan IP : 192.168.1.6 255.255.255.252Public address pool : 172.168.10.6 to 12if i configure one address on Ethernet port1 as nat outside 192.168.1.6 255.255.255.252.the ip address given for wan & pool are different.Then how can i configure pool and how to configure nat inside eg 185.168.10.1 to 255the above ip are not actual ips just given for example.
View 6 Replies View RelatedI have a cisco 2911 set up at one of my sites and it is configured with sub-interfaces as this provides a default gateway to each of the offices.I have just had a 100mb leased line put in and i have a couple of questions regarding the config.let me start by telling you how it is set up .I have 3 HP Procurve switches connected together then that connects to the Cisco and the Cisco connects to a Zywall
HP Switches > Cisco 2911 > Zywall > Internet
We are wanting to remove the Zywall and connect the Cisco to the Leased line box
HP Switches > Cisco 2911 > Leased Line > Internet
The config of the cisco is
G0/0 - is up but no cable connected as this holds the sub-interfaces
G0/1 - Connects the Zywall - 192.168.1.1 (this has firewall rules to forward traffic through)
G0/2 - Leased Line
The way i have configured the sub interfaces is with its own DHCP pool and default router, some of the offices have there own ADSL router and hold there own Internet connection and the default gateway for that is 192.168.xxx.253 and the offices that use the Cisco use default gateway of 192.168.xxx.254
Now my question is how would I move everyone onto the Leased line and get rid of the Zywall ? Would it be as simple as giving the leased line an address and put in a static route to forward all traffic through that connection ? Or am i missing a trick or 2.
How to configure leased line from the ONT connection on Cisco 1841 router . there have public IPs on the interfaces fa0/0 & fa0/1.
View 4 Replies View RelatedLeased line is between dammam to dubai and the dammam office is getting internet from dubai.The ip address of Dammam office is class A (Public IP) x.x.x.x and for dubai it is y.y.y.y which we are using as proxy for accessing internet.I purchase the local DSL direct line connection through cable from Local Provider and this ip address range is 192.168.1.0 - 192.168.1.254.Is it possible to use the DSL line as failover, so if one line goes down the user should remove proxy and can use local internet.The router which is using is cisco 1800.
I believe that failover is possible, 100%, but would like to know how I can do it and requesting for sharing more inputs about failover in this case.
I am going to design one network. I had queries with this design.Let me explain scenario first( it was attached below).I have two sites, Site-A and Site-B, repectively.
In site-A i have one Cisco 1841 router, one Cisco ASA 5510 firewall and One cisco 3560 layer 3 switch.
in site-B i have one Cisco 1841 router, one Cisco ASA 5505 firewall and One Cisco 3560 layer 3 switch.
From ISP side
I have point-to-point leased line between sites A and B. And both sites have internet connectivity from another ISP.
I planned to terminate leased line in cisco 1841 router in both branches for branch to branch connectivity.
I will configure site to site VPN between two sites, A and B.
Here my query was i want make VPN as failover connectivity if leased line fails. In both the cases, i need internet to the inside users in both sides.
Summary requirement:Leased line is Primary and VPN is Back-up, if leased line fails. In both cases internet is needed to inside users.
I have two sites connected via 2901 routers to a head end with an ASA 5510, the WAN circuits are LES running at 100MB and at the head end we have a 100MB leased line. All WAN circuits are provided wires onlyby another supplier. I have setup the two 2901 routers with inside IP addresses on GE0/0 and a /30 subnet for the GE0/1 interfaces to the ASA over the LES circuit.
The LES circuits are set to 100MB but the problem I am having is that one of the 2901s will only negotiate at 10MBps Half Duplex with the ASA at 100MB Half Duplex, the other will negotiate at 100MBps Full Duplex at both ends. My WAN provider tells me both LES circuits are the same so I cannot work out why one will negotiate at 100MB Full and the other at only 10Mb Half.
At the head end I have and ASA 5510 connected to the WAN providers 100MB circuit but testing from my end sites I can only get 6MB download and 0.5MB upload on an Internet Speedtest.
I used Wireshark when downloading from my end sites and I can see lots of TCP retries and duplicates so I think this is a duplexing issue, my question is, my WAN provider is stating the issue is nothing to do with them and it is my 2901 and ASA that is at fault, they state if they connect a laptop to the LES circuit and then their leased line they get 100MB up and down.
I am a total new comer for Cisco Router. All I know is plug the console cable to a serial port on a PC, fire-up HyperTerminal to view and that's it. I don't know any command or scripts.
I am trying to setup my client connection, I already receive the required configuration settings from ISP. It is a Leased Line Serial connection.
How to setup the router with the below configuration.
Serial IP : 1.X.XX.222
Serial Netmask : 255.255.255.XXX
LAN IP : 1.X.XXX.1 to 1.X.XXX.31
LAN Netmask : 255.255.255.XXX
[Code] ....
What are the commands for Configuring Cisco 1921 Route's Gigabit Port G0/0 or G0/1 for Leased Line termination having Ethernet Hands Off
Modem Provided by ISP (BSNL ) is CTR-U
We plan migrate an old existing WAN architecture based on legacy data serial links. These links will be consolidated on a E1 channalized card.
My question :
Is the HWIC-2CE1T1-PRI need a PDVM DSP ressources on router to oparate for data leased lines or no?
The VWIC3-1MFT-T1/E1 will be used for the backup dial in ISDN connexions? this type of cards a PVDM DSP ressources for data connexions or no?
ISR router are 2911.
I have configured cisco 1751 router for internet with nating. Internet browsing working fine. But We have polycom hdx 6000 conference system to connect from remote site.
1. While calling remote ip it is ringing and connecting but not displaying any thing on the screen but their side is displaying.
2. When they call our side ip it cannot connecting.
I have connected netgear router then video conference is working fine (with out port forwarding also). If I configured that router between 2 local sites (not on internet line) its working fine where i did not configured any thing just given routing. Configure same situation using internet leased line.
We have configured ASA 5510. We have configure Ethernet 0/0 ( Outside ) connected with ADSL line and Ethernet 0/1 ( Inside ) Local LAN. we have configured NAT and all the traffic is passing through outside interface. Now we have connected ethernet 0/3 ( leasedline ) interface with static public IP. Now we want to allow SMTP traffic to pass through from this interface.
How to configure it if we want our local lan SMTP traffic sending through new leased line ( Static Public IP ).
Cisco 2500 series access servers show line usage with the "show line" command:
View 2 Replies View RelatedI have remote access as I work at home on a government laptop that has Entrust( for security). My IP lapse time is set for 1 hour and every hour I am losing full connection due to having to sign back into Entrust. I need to be able to lenghten my lapse time on my work computer. My other two personal computers are fine with 1 hour as there is no Entrust on either of those laptops.....is it possible for me to change the lapse time to say 12 hours, 1 weeks, whatever??
View 4 Replies View RelatedMy current setup.
Layout:
Line01 Line02
| |
Cisco 2951 Cisco 2951
---------------------
|
Cisco 3750G - Server #1 & #2 for domain controller, sharepoint, etc
|
---------------------
| |
Cisco 2960 Cisco 2960
| | | | | | | ... | | | | |
workstation #1, #2, .... #70
And I would like to ask some opinion on the best configuration for the above layout:
1. Configuration #1 - Using load sharing and automatic failover So I want to ask whether there's any link/url that provides details/guides on how to setup the load sharing and failover?
2. Configuration #2 - Workstations 1 - 35 will be routed through Line01 gateway and workstations 36 - 70 will be routed through Line02 As for this configuration, it's done now. However, I want to know whether there's any software (preferred web based application which allows me to change the gateway from line #1 to line #2 for all 70 computers instead of having to go to each workstation to update the gateway).
I'm trying to configure policing and/or shaping on a setup of 2 x ASA 5505 Sec Plus. The units are placed in office A and office B and each have a ISP connection to the internet and a leased line with a capacity of 4/4 Mbit/s for interoffice communication.
On each ASA there's four subnets. VLAN 200 is used to connect the offices through the leased line.
Subnets:
Outside = 2
Data = 10
Voice = 100
Linknet = 200
I've read a lot of articles and posts about shaping and policing on the ASA but still can't get it to work like I wan't to. I'm trying to limit all traffic besides IP-telephony traffic to 3 Mbit/s and thus reserving 900 Kbit/s for voice traffic. I tried setting a service-policy on the linknet interface on each ASA and set Traffic match to Any traffic and QoS settings for both input and output.
I can see traffic passing the policy when I run the "show service-policy police" command but it never seems to be high enough to be policed which is strange since the ASDM monitoring shows that I'm pushing 3900 kbit/s. I file transfers verifies that policing does'nt work.
We have 1841 router with HWIC-4ESW we need to config point to point data Dual leased lines failover concept please find attached diagram.
View 3 Replies View RelatedOkey so the issue here is that my computer just looses its connection after ive downloaded somewhat or something.especially when im downloading from you know what So.when i try to go on my Chrome, explorer, firefox WHATEVER it says Additional logon information may be required.so i click on that annotation and it just brings me to the home page of my main browser google home page with ofcourse no internet what so ever.. im using Wireless and wired (best connection) for the wired i use it through a cisco but neither works.it works fine on laptop and my iPhone 4.
View 1 Replies View RelatedWhen I login to Facebook on my home computer it opens and trys to read something additional (the little activity circle continues to roatate) but it never completes, it is like it is in an endless loop so my browser (IE 9) locks up and I have to use task manager to terminate. I can get into facebook on my office computer with no problem. Also my wife has the same problem on her facebook account.
View 3 Replies View RelatedI've been running a small home network with no problems for the last year. I'm unsuccessfully attempting to add a wired connection in my basement, but the laptops do not recognize the connection. I've tried laptops running Vista and WinXP -- neither works.
The attached graphic depicts the current state of the network and also identifies the problem connections. At first I thought my new CAT-5 cables were the problem, but I've ruled that out by swapping the cable from my desktop (hardwired to the wireless router) to the laptop.
I've also pasted the IPCONFIG text from the desktop pictured in the attachment. Is there any obvious reason that setup this isn't working??
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersMark>ipconfig/all
[Code]....
From where I will get additional driver to share windows 7 pc to windows xp users
View 1 Replies View RelatedI am in the process of deploying an additional Cisco 1142 AP into my network. I would like to set it up to be the same SSID as the first one, and be able to have laptops roam from AP to AP. I am simply trying to expand the current coverage of my wireless network. I have both APs mounted and access to both.
-CISCOAP01 - 192.168.2.2
-CISCOAP02 - 192.168.2.3
What do I need to do (configre) to make this happen? I am rather new with Cicso. I am using the web interface to setup the APs. The first one has been up and running for about a year now with no problems. [code]
Im wanting to add an additional module in to my Cisco 4500. Is as simple as plug and play or is there some commands that I need to add or anything I should be aware of.
View 2 Replies View RelatedAs my original Innbox V50U modem/router does not have a strong enough wifi signal I had to add in an additional wifi router - I used a Cisco Linksys E4200.The problem is that if I connect my laptop to the cisco router I can see the Innbox router but not vice versa. There is an additional problem as I have a wireless printer that is connected to the Cisco router. If I connect to the Innbox router I cannot use this printer as I cannot see its IP address.I read somewhere it might be down to the subnet mask. both are set to 255.255.255.0Apologies if this is n00b stuff but I have not had this problem before, I just naturally though the two networks would be able to talk to each-other.
View 1 Replies View RelatedI will be adding wireless access points or repeaters on a business network. The business already has one wireless router using a https login, that 15 computers are wired to, through switches. This Secure http router is directly connected to the cable modem.Would I be loosing the benefit of Secure http by adding wireless access points or repeaters that don't support it? Or would they be securely routed by the main https router connected to the gateway?I have never had the opportunity to work with a secure http router before.
View 4 Replies View Relatedi'm connecting to the internet using a desktop pc and a D-Link DSL-2560U (modem + wireless router). The wifi signal is very low on the other side of the house. I also have another wireless router - a Trendnet TEW-431BRP, and i want know if i can put it in the middle of the two areas of the house in order to boost the wifi signal in that area. How can i do it?
View 4 Replies View RelatedSo far we add any router in the existing network simply by disabling DHCP server, and adding LAN ip for that. We don't add WAN detail at all in the additional routers. And plug one cable from main network to the LAN port of the additional routers.So we basically use that additional routers only as a access point for WIFI.But what I wonder is if it's possible for me to use the additional routers with the same feature as of the main routers i.e. Enabling DHCP server so that it too can give its own DHCP ip address.
View 2 Replies View RelatedI have an existing external IP block on eth1 which is working fine. I have another eth3 card which I want to use for my additional IP range.So my ISP gave me a new /27 block is addition to what I have now. This block is supposily active and nothing is needed to configure on the ISP router, it is said that it is autmatically available and ready to use once I configure my PIX.I am using the PIX GUI and running into an error while trying to create a NAT pool "Start and end addresses overlap with existing range"
View 53 Replies View RelatedI want to split the usage of the AP so that visitors are on their own wireless connnection and VLAN.We have 2 WAP4410N APs. One AP acts as a repeater for the another AP.They are both in 4.0.4.2 firmware.We are using WPA2 RADIUS authentication, and would like for visitors to use WPA2 PSK. Under Wireless tab, I have 1 SSID, but the other 3 available boxes for SSIDs are greyed out.When I click in them, they will not allow me to type an ID.I watched a video of how to add SSIDs and VLANs, and it looked simple enough.He just clicked in the box and was able to add more IDs.Could my current config be preventing me from adding additional SSIDs?
View 6 Replies View RelatedI recently purchased another 1142 AP to expand out our current wireless infrastructure, my question is, what exactly needs to be done for this to work so that users can roam freely and auto-connect to the closet AP with the best connection without getting disconnected?
I have set all the settings the exact same on the new AP to match the existing AP. (How to save the configs into a file would be great, I am not sure how to do that)... But anyhow, before I launch it, I would like to be sure I am correct so I do not bring down the existing network. Of course, the only difference between the 2 are the IP addresses. AP1 is 192.168.2.2 and AP2 is 192.168.2.3
All computers are using Linksys Wireless-N cards.
I confgured one L2L VPN on my ASA 5505.
How to add another L2L configuration for an additional peer ?
If I am to add the Self-generated certificate of my new CAS to my existing CAM's trusted certificate authorities list, will it just be added or will it replace the existing trusted certificate?
View 4 Replies View Related