Cisco WAN :: Leased Line Connection Through ONT To 1841 Router
Jul 29, 2012How to configure leased line from the ONT connection on Cisco 1841 router . there have public IPs on the interfaces fa0/0 & fa0/1.
View 4 Replies
ADVERTISEMENT
Cisco Firewall :: 1841 / Failover Between Leased Line And VPN
Jul 15, 2011I am going to design one network. I had queries with this design.Let me explain scenario first( it was attached below).I have two sites, Site-A and Site-B, repectively.
In site-A i have one Cisco 1841 router, one Cisco ASA 5510 firewall and One cisco 3560 layer 3 switch.
in site-B i have one Cisco 1841 router, one Cisco ASA 5505 firewall and One Cisco 3560 layer 3 switch.
From ISP side
I have point-to-point leased line between sites A and B. And both sites have internet connectivity from another ISP.
I planned to terminate leased line in cisco 1841 router in both branches for branch to branch connectivity.
I will configure site to site VPN between two sites, A and B.
Here my query was i want make VPN as failover connectivity if leased line fails. In both the cases, i need internet to the inside users in both sides.
Summary requirement:Leased line is Primary and VPN is Back-up, if leased line fails. In both cases internet is needed to inside users.
Cisco WAN :: Setting Up 2811 Serial Leased Line Connection
Feb 7, 2012I am a total new comer for Cisco Router. All I know is plug the console cable to a serial port on a PC, fire-up HyperTerminal to view and that's it. I don't know any command or scripts.
I am trying to setup my client connection, I already receive the required configuration settings from ISP. It is a Leased Line Serial connection.
How to setup the router with the below configuration.
Serial IP : 1.X.XX.222
Serial Netmask : 255.255.255.XXX
LAN IP : 1.X.XXX.1 to 1.X.XXX.31
LAN Netmask : 255.255.255.XXX
[Code] ....
Cisco WAN :: Failover On Router 1800 Having DSL And Leased Line
Feb 4, 2013Leased line is between dammam to dubai and the dammam office is getting internet from dubai.The ip address of Dammam office is class A (Public IP) x.x.x.x and for dubai it is y.y.y.y which we are using as proxy for accessing internet.I purchase the local DSL direct line connection through cable from Local Provider and this ip address range is 192.168.1.0 - 192.168.1.254.Is it possible to use the DSL line as failover, so if one line goes down the user should remove proxy and can use local internet.The router which is using is cisco 1800.
I believe that failover is possible, 100%, but would like to know how I can do it and requesting for sharing more inputs about failover in this case.
Cisco WAN :: Configuring 1921 Router For Leased Line With Ethernet?
Oct 3, 2012What are the commands for Configuring Cisco 1921 Route's Gigabit Port G0/0 or G0/1 for Leased Line termination having Ethernet Hands Off
Modem Provided by ISP (BSNL ) is CTR-U
Difference Between Leased Line And DSL Line
Mar 27, 2012The reason is i want to know the difference between the leased line and the DSL line. The whole thing behind the confusion is, We plan to have a high speed internet connection in our office. We will don't have a branch office or some thing like that. I preffered to have high speed internet in our office. I found in some website that Lease line will have high speed connectivity(Upto 10Gbps). Can i use the lease line or DSL is enough for our office. Our office contains of 82 user who will use internet.
View 2 Replies View RelatedWhat Are Additional IP Address In Leased Line
Mar 31, 2011my company has a 4mbps leased line from TTSL . we are getting 2 WAN IP and 2 LAN IP. in Addition we are also getting 12 additional IPs .-what is additional IP, their uses?-how are the 2 wan ips configured? & how they are distributed in network? -is 1 IP from the ISP sufficient if i have a 1:1 internet bandwidth connection?
View 9 Replies View RelatedConfiguration Of Internet Leased Line?
Dec 28, 2011I got following IP address from BSNL to configure Internet leased line.OFC cable was terminated at our premises. it has to connect Ethernet port.Say eg.Wan IP : 192.168.1.6 255.255.255.252Public address pool : 172.168.10.6 to 12if i configure one address on Ethernet port1 as nat outside 192.168.1.6 255.255.255.252.the ip address given for wan & pool are different.Then how can i configure pool and how to configure nat inside eg 185.168.10.1 to 255the above ip are not actual ips just given for example.
View 6 Replies View RelatedCisco :: 2911 Connecting To A Leased Line?
Aug 3, 2012I have a cisco 2911 set up at one of my sites and it is configured with sub-interfaces as this provides a default gateway to each of the offices.I have just had a 100mb leased line put in and i have a couple of questions regarding the config.let me start by telling you how it is set up .I have 3 HP Procurve switches connected together then that connects to the Cisco and the Cisco connects to a Zywall
HP Switches > Cisco 2911 > Zywall > Internet
We are wanting to remove the Zywall and connect the Cisco to the Leased line box
HP Switches > Cisco 2911 > Leased Line > Internet
The config of the cisco is
G0/0 - is up but no cable connected as this holds the sub-interfaces
G0/1 - Connects the Zywall - 192.168.1.1 (this has firewall rules to forward traffic through)
G0/2 - Leased Line
The way i have configured the sub interfaces is with its own DHCP pool and default router, some of the offices have there own ADSL router and hold there own Internet connection and the default gateway for that is 192.168.xxx.253 and the offices that use the Cisco use default gateway of 192.168.xxx.254
Now my question is how would I move everyone onto the Leased line and get rid of the Zywall ? Would it be as simple as giving the leased line an address and put in a static route to forward all traffic through that connection ? Or am i missing a trick or 2.
Cisco WAN :: 2901 To ASA 5510 Via Leased Line Poor Throughput
Feb 16, 2012I have two sites connected via 2901 routers to a head end with an ASA 5510, the WAN circuits are LES running at 100MB and at the head end we have a 100MB leased line. All WAN circuits are provided wires onlyby another supplier. I have setup the two 2901 routers with inside IP addresses on GE0/0 and a /30 subnet for the GE0/1 interfaces to the ASA over the LES circuit.
The LES circuits are set to 100MB but the problem I am having is that one of the 2901s will only negotiate at 10MBps Half Duplex with the ASA at 100MB Half Duplex, the other will negotiate at 100MBps Full Duplex at both ends. My WAN provider tells me both LES circuits are the same so I cannot work out why one will negotiate at 100MB Full and the other at only 10Mb Half.
At the head end I have and ASA 5510 connected to the WAN providers 100MB circuit but testing from my end sites I can only get 6MB download and 0.5MB upload on an Internet Speedtest.
I used Wireshark when downloading from my end sites and I can see lots of TCP retries and duplicates so I think this is a duplexing issue, my question is, my WAN provider is stating the issue is nothing to do with them and it is my 2901 and ASA that is at fault, they state if they connect a laptop to the LES circuit and then their leased line they get 100MB up and down.
Cisco WAN :: 2911 - Need PVDM When Use HWIC-2CE1T1-PRI For Leased Line
Oct 11, 2012We plan migrate an old existing WAN architecture based on legacy data serial links. These links will be consolidated on a E1 channalized card.
My question :
Is the HWIC-2CE1T1-PRI need a PDVM DSP ressources on router to oparate for data leased lines or no?
The VWIC3-1MFT-T1/E1 will be used for the backup dial in ISDN connexions? this type of cards a PVDM DSP ressources for data connexions or no?
ISR router are 2911.
Configuration Of Video Conference On Cisco 1751 Using Internet Leased Line
Feb 20, 2012I have configured cisco 1751 router for internet with nating. Internet browsing working fine. But We have polycom hdx 6000 conference system to connect from remote site.
1. While calling remote ip it is ringing and connecting but not displaying any thing on the screen but their side is displaying.
2. When they call our side ip it cannot connecting.
I have connected netgear router then video conference is working fine (with out port forwarding also). If I configured that router between 2 local sites (not on internet line) its working fine where i did not configured any thing just given routing. Configure same situation using internet leased line.
Cisco Firewall :: 5510 How To Configure Local LAN SMTP Traffic Sending Through New Leased Line
Jun 11, 2012We have configured ASA 5510. We have configure Ethernet 0/0 ( Outside ) connected with ADSL line and Ethernet 0/1 ( Inside ) Local LAN. we have configured NAT and all the traffic is passing through outside interface. Now we have connected ethernet 0/3 ( leasedline ) interface with static public IP. Now we want to allow SMTP traffic to pass through from this interface.
How to configure it if we want our local lan SMTP traffic sending through new leased line ( Static Public IP ).
Cisco Switching/Routing :: 887 Router / 1841 - Dial Up On ADSL Line To New Site
Nov 9, 2012I've moved a Cisco 887 router from a site where it was used to dial up on an ADSL line to a new site where we have a EFM circuit which terminates at a Cisco 1841 router managed by our ISP. I therefore need to re-configure our 887 router to work as a conduit from our servers back to the Cisco 1841 as its gateway.
I have asked from our ISP and they told me that i need to configure the 887 to use IP address 176.35.140.65 255.255.255.248 and its gateway should be 176.35.140.70. That's great advice in theory but I don't know how to configure this correctly
Our internal network is using subnet 192.168.42.XX which will need to be retained for local devices.
IP Leased Time And Losing Connection
Oct 19, 2011I have remote access as I work at home on a government laptop that has Entrust( for security). My IP lapse time is set for 1 hour and every hour I am losing full connection due to having to sign back into Entrust. I need to be able to lenghten my lapse time on my work computer. My other two personal computers are fine with 1 hour as there is no Entrust on either of those laptops.....is it possible for me to change the lapse time to say 12 hours, 1 weeks, whatever??
View 4 Replies View RelatedCisco WAN :: 1841 DSL Line Security Config
Dec 18, 2011I configured a 1841 router that connects to a DSL modem. This DSL connection is our Internet connection for vendor and IT testing. I have connectivity to the Internet using nat and have configured the router to act as a DHCP server. It seems to be working fine. I just want to configure some best practices for securing the device from the outside access. Is there some standard best practices I should be configuring?
View 2 Replies View RelatedCisco WAN :: Fast Ethernet Is Up / Line Protocol Down 1841
Aug 2, 2012I have a cisco 1841 whose LAN interface is showing status as "Fastethernet 0/1 is up , line protocol is down" the duplex and speed settings in the Router are in Auto mode and the Router was working fine till now , when i changed the duplex settings to duplex full , speed 100 the ping replies comes back with 5-6 replies then the link dies again..
View 1 Replies View RelatedCisco WAN :: Serial Up Line Protocol Down On 1900 Router With Single T1 Connection
Jul 11, 2012Have been battling a router connection to new ATT t1 connection. Router was configured and sent from sister company to this new location. We have had ATT tech test circuit and it tests good, had cat5 cable tested from ATT to router, it tests good. I continue to get serial up/ line protocol down status though and cant communicate to it from wan.
View 4 Replies View RelatedLinksys Wireless Router :: EA2700 - Way To Get Phone Line Connection?
Sep 1, 2012I have century link DSL with a Westell 7500. I bought the EA2700 as a replacement. I assume its not a dsl since there is no phone line connection.
View 2 Replies View RelatedCisco VPN :: Establish VPN Connection Between ASA And 1841 Router?
Feb 7, 2011I am facing problem when trying to establish VPN connection between ASA and 1841 router. Peer comes up but traffic is encrypt and decrypt. when assign route (ip route 192.168.x.0 255.255.255.0 fa0/0) to remote local subnet there is a traffic but one reply and one drop
ping from
192.168.y.62
-------------------------------------------------
Reply from 192.168.x.55: bytes=32 time=493ms TTL=127Request timed out.Reply from 192.168.x.55: bytes=32 time=633ms TTL=127Request timed out.Reply from 192.168.x.55: bytes=32 time=375ms TTL=127Request timed out.Reply from 192.168.x.55: bytes=32 time=528ms TTL=127Request timed out.
[code].....
Cisco VPN :: Between 2 Router 1841 Using HDSL Connection?
Feb 15, 2011I've to realize a VPN (ipsec) between 2 side that use a Router Cisco 1841, each one with its own public IP.The 2 side can ping each one with Public IP but the VPN are in DOWN's state.The schema is the following:
192.168.1.0/24 (LAN1) <-> Ro1 (X.X.X.X) <- VPN -> (Y.Y.Y.Y) Ro2 <-> 192.168.2.0/24 (LAN2)
the configuration of Ro1 is showed of following, the same configuration is present also in Ro2 but with different IP address
sh runBuilding configuration...Current configuration : 9808 bytes!version 12.4service timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname TEST!boot-start-markerboot system flash c1841-adventerprisek9-mz.124-24.T.binboot-end-marker!logging message-counter sysloglogging buffered 51200 warnings!no aaa new-modeldot11 syslogno ip source-route!!! !ip cefno ip bootp serverip domain name test.itip name-server x.x.x.xip name-server x.x.x.xip inspect log drop-pktip inspect max-incomplete low 300ip inspect max-incomplete high 400ip inspect one-minute low 300ip inspect hashtable-size 2048ip inspect tcp synwait-time 20ip inspect tcp max-incomplete host 300 block-time 60ip inspect name IDS tcpip inspect name IDS udpip inspect name IDS ftpno ipv6 cef!multilink bundle-name
[code]....
so, of following the screen of the answer of these commands.
Ro1(config)# sh crypto session Crypto session current statusInterface: Serial0/0/0.1Session status: DOWNPeer: 81.21.17.146 port 500 IPSEC FLOW: permit ip 192.168.1.0/255.255.255.0 192.168.2.0/255.255.255.0 Active SAs: 0, origin: crypto mapRo1(config)# sh crypto map interface serial 0/0/0.1Crypto Map "VPN" 1 ipsec-isakmp Peer = Y.Y.Y.Y Extended IP access list 150 access-list 150 permit ip 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255 Current peer: Y.Y.Y.Y Security association lifetime: 4608000 kilobytes/86400 seconds Responder-Only (Y/N): N PFS (Y/N): N Transform sets={ VPN-SET: { esp-3des esp-sha-hmac } , } Interfaces using crypto map VPN: Serial0/0/0.1
Cisco WAN :: How To Do IPL Connection Using 2801 Router To 1841
Dec 26, 2012I need some clarification if it is possible to do an IPL connection between Cisco 2801 (T1) to Cisco 1841 (E1) via Ethernet (2801) to Serial (1841).
I am unable to find any documentation about this and I need to connect our network to our overseas office.
Our side uses the 1841 router and our provider has set-up our E1 connection to be via Serial interface while on our overseas office uses the 2801 and will connect via the T1 card, which by the way does not have any serial interface ports just ethernets.
So far checking on how to configure this, I am unsure on how the connection will happen since the info that I got is that T1 does not have the option to hold an IP address (also unsure on this though). With this in mind and that the 2801 does not have serial interfaces, does that mean that IPL connection would be via the available Ethernet ports?
Cisco :: Line Usage In Case Of Show Line On 2500 Series?
Oct 10, 2012Cisco 2500 series access servers show line usage with the "show line" command:
View 2 Replies View RelatedCisco Infrastructure :: 1941 / Analog Line Connection Failing?
Jul 10, 2012I have a 1941 Cisco router with WIC-!AM-V2 card that is uning pots( regural phone ) line for data traffic.the problem I am having is the line is establishing connection but it intermittently dropos.The router is configured to dial to Centraal office and I have more that 100 other locations with the same setup that are working fine. The only differene on htis one is it is going thru a PBX line.
View 1 Replies View RelatedCisco Switching/Routing :: 2951 / 2 Leased Lines In LAN Network
Oct 24, 2011My current setup.
Layout:
Line01 Line02
| |
Cisco 2951 Cisco 2951
---------------------
|
Cisco 3750G - Server #1 & #2 for domain controller, sharepoint, etc
|
---------------------
| |
Cisco 2960 Cisco 2960
| | | | | | | ... | | | | |
workstation #1, #2, .... #70
And I would like to ask some opinion on the best configuration for the above layout:
1. Configuration #1 - Using load sharing and automatic failover So I want to ask whether there's any link/url that provides details/guides on how to setup the load sharing and failover?
2. Configuration #2 - Workstations 1 - 35 will be routed through Line01 gateway and workstations 36 - 70 will be routed through Line02 As for this configuration, it's done now. However, I want to know whether there's any software (preferred web based application which allows me to change the gateway from line #1 to line #2 for all 70 computers instead of having to go to each workstation to update the gateway).
Cisco VPN :: 1841 - Creating Connection Using SDM
Feb 12, 2011i am trying to make site to site VPN on cisco 1841 router using SDM , but I faced a strange problem . I successfully install sdm , internet browser , disabled block pop up , and java . i successfully can run SDM and configure the router using it .
BUT\ when I select VPN>>Site to site VPN >>Create Site to Site VPN tap >> and Press on Lanuch the selected task to start the creation process using the wizard Unfortunately it is not working ,, I don't know why ?
I tried with another PC , another SDM version , another browser .
Cisco WAN :: 1841 Connection Between ISP And Firewall
Apr 2, 2012I have a Cisco 1841 serving as a connection between my ISP and my Firewall (non Cisco).
I seem to be having performance issues with my traffic going through the Router.HTTP (web browsing) is fine andI get my download rate as I would expect for a 10mbps connection.But anything to do with my VPNs I find a delay when sending via the 1841.(all my VPNs are managed by my Firewall and I have never had problems with those).
I also have a legacy ADSL connection to my firewall, which bypasses the 1841 and I am having no issues on that at all.If anything it is quicker! Which is madness as my Fibre should out-perform it easily.This leads me to believe the issue is not with the Firewall.
My 1841 is very simply setup, 2 fa interfaces with simply a default gateway setup within it.Which leads me to ask if I need more static routes in or a dynamic route protocol setup?
Cisco Firewall :: 5505 - How To Apply Policing On ASAs With Leased Lines
Jul 2, 2012I'm trying to configure policing and/or shaping on a setup of 2 x ASA 5505 Sec Plus. The units are placed in office A and office B and each have a ISP connection to the internet and a leased line with a capacity of 4/4 Mbit/s for interoffice communication.
On each ASA there's four subnets. VLAN 200 is used to connect the offices through the leased line.
Subnets:
Outside = 2
Data = 10
Voice = 100
Linknet = 200
I've read a lot of articles and posts about shaping and policing on the ASA but still can't get it to work like I wan't to. I'm trying to limit all traffic besides IP-telephony traffic to 3 Mbit/s and thus reserving 900 Kbit/s for voice traffic. I tried setting a service-policy on the linknet interface on each ASA and set Traffic match to Any traffic and QoS settings for both input and output.
I can see traffic passing the policy when I run the "show service-policy police" command but it never seems to be high enough to be policed which is strange since the ASDM monitoring shows that I'm pushing 3900 kbit/s. I file transfers verifies that policing does'nt work.
Cisco WAN :: 1841 With 3G HWIC - Backup WAN Connection?
Jul 3, 2011I'm trying to backup my primary WAN with secondary backup connection - 3G WAN through Cellular 0/0/0.Point is that I need to track some external IP address on my primary interface, for examle 8.8.8.8. If it is not reacheable, then router brings up backup connection - 3G. This can be done by using dialer-watcher.Simple.But unfortunately my primary WAN interface is an FastEthernet, which is the coonected to a switch, switch to WAN . There is no dialer-watch commands on it. Thats sad .
One more time :
WAN -> SWITCH -> ROUTER(WITH 3G HWIC and Fa 0/0 connected to switch).
Cisco Switching/Routing :: Connection Between 1841 And Linksys?
Apr 9, 2013I tried to connect a 1841 to a Linksys with a static route. I am able to ping from a computer in the 1841 to a computer in the linksys network, but I can't ping from a computer in the Linksys network to a computer in the 1841 network?
View 7 Replies View RelatedCisco WAN ::1841 Routers Handle 45Meg Connection?
Apr 28, 2009This is only a small portion of our network but my question is, can these 1841 routers handle a 45Meg connection? I thought these routers were designed for T1/E1 type speeds. I know I saw a router performance document somewhere that showed 1841's could handle 38.4MB of traffic and that is only with routing turned on. If anything else is enabled, like access lists, NetFlow or whatever, that number will decrease because of the capacity of the router. Am I correct in these statements? Any document or anything else that shows performance of these routers?
View 14 Replies View RelatedCisco WAN :: 1841 ADSL Interface Dropping Connection
Jul 2, 2012We have an ADSL2+ line from a WIC in a 1841, everything has been fine for the last few years and then the last few months the connection going down. When checking the interfaces the ATM0/0/0 is up up and the same for the dialer interface we are using, they are both up/up, but this still needs a reload of the router to be functional again, shutting the interfaces does not bring the connection back up.
I am not an expert on ADSL lines, I have never really had a problem with anything previously. The router was running Netflow to a network monitor wondering if this or logging was causing an issue with entries in the buffer??
Here is an output of show dsl int, would change the firmware, it has been fine all this time before though we are running IOS 12.4(24)T1 advseck9-m, as far as I can seen from our ISP the config for ADSL is all correct. [Code]
Cisco WAN :: 1841 - Layer 2 Connection Between Distant Model?
May 21, 2012I have two 1841's connect to the Internet via DSL;
fa0/0 --- 1841-R1 --- DSL1 ---------------------[INTERNET]--------------------- DSL1 --- 1841-R2 --- fa0/0
I am on the LAN attached to fa0/0 on R1 and I need layer 2 connectivity to a device on fa0/0 on R2. I'm not sure if this is possible with 1841's or not? I made a GRE tunnel between the two and was going to add a BVI and bridge the tunnel at each end with fa0/0 at eah end, but the 1841's don't support BVIs so I'm a bit stumped here! Would L2TP work here?
R2 is a remote router running C1841-SPSERVICESK9-M. R1 is local running C1841-ADVENTERPRISEK9-M. I can't change the remote router so if the answer is not support in C1841-SPSERVICESK9-M I won't be able to do this.