I was in the process of recovering a password on a nexus 5548 swith when it finally gets in to the boot mode.I think i lost all my bootloader code.How do i get it back on the switch
loader> load n5000-uk9.5.0.3.N2.1.bin
Error 27: Unrecognized command
how to restore my IOS on this device
Base ethernet MAC Address: 00:0a:b7:07:35:80Xmodem file system is available. The system has been interrupted prior to initializing theflash filesystem. The following commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init load_helper boot switch: flash_initInitializing Flash...flashfs[0]: 3 files, 1 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 3612672flashfs[0]: Bytes used: 1815040flashfs[0]: Bytes available: 1797632flashfs[0]: flashfs fsck took 3 seconds....done Initializing Flash.Boot Sector Filesystem (bs:) installed, fsid: 3Parameter Block Filesystem (pb:) installed, fsid: 4ô
Two 5548 switches running switch profile and it got out of sync (probably because one of the switches lost power before it has chance to save configure). Once the switch profile out of sync, you can't make any change to the switch profile any more, verification will fail.Is there any good way to get the switch profile re-sync without recreating it?
View 2 Replies View RelatedCurrent our environment is the following:
Core1 ---- Core2
| |
Nexus5k
| |
N2k, N2k, N2k (FEX)
||
Servers, hosts, etc..
We would like to add another Nexus5k to this topology. However, it has to be a zero downtime infrastructure add-on. When setting up the keep-alive, peer-link, vPC and vdc domain, will there be any upset in network traffic on the current N5k?Also, are the Nexus5k configurations synchronized or are they independent from one another? Before setting up the new 5k, should i configure it to teh 6509's, and vPC's to the Nexus2k's before setting up peer-link?
My Name is senthil i need to configure new hp sever with Nexus 5548 how to config.. server side everything finished just i need only
Config tips for Nexus 5k for New server
I am in the process of setting up an interop lab for some engineers. The enviornment will consist of some 3750's, H3C's and ProCurves. My concern is that the end user will have Priv-Exec access for CLI usage on the 3750's and they can change the "en" password (I hope they don't but it has happened).Is there a way I can "break in" during the boot process to reset the password? The reason I am doing it this way is because I have an Altiris server with rebuild automation scripts in xpect and I would like to automate the process so I do not have to use a manual factory default reset.
View 5 Replies View RelatedI am facing switch reboot issue when power of switch restore from RPS to AC.
View 1 Replies View RelatedOn cisco and am having some issues with intervlan routing. I have followed the vids and manuals but just can seem to get this working. I have the following network lab set up.
Vlan 10 = 10.70.1.9/24
Vlan 20 = 192.168.0.1/24
ME2400 firmware
ROM: Bootstrap program is ME340x boot loader
BOOTLDR: ME340x Boot Loader (ME340x-HBOOT-M) Version 12.2(35r)SE3, RELEASE SOFTWARE (fc1)
[Code]...
after upgrading IOS image to V15 on four 2960S switches: Should I make the boot loader image to match the IOS version?I never thought about this while upgrading IOS image unless there is boot issue. I googled for answer but no luck there...
I checked download section on Cisco.com for C2960S-48FPS-L switch and there is simply no boot loader image..The running boot loader is C2960S-HBOOT-M Version 12.2(55r)SEThe running IOS is: 15.0 (2) SE2.
I am planning to upgrade BootLoader image of 7206VXR router due to booting issue. The router is not booting .But if I go to rommon and give boot it will boot.So I am upgarding my Boot Loader image. Now the Bootloader image and IOS image are exactly same.Can I upgarde the Bootloader image to latest version without upgarding IOS?
View 3 Replies View RelatedGot a long lingering, year long issue that has spanned about 8 supervisor cards and a complete chassis swap. The 6509 acts as a ITN in our facility. The active sup card at random points of pipe usage boots into rommon mode, seriously inhibiting our company. I'm able to swap the 2 fiber pairs that we had going into the active supervisor card into the secondary and usually this works for another random amount of time, however, today it occured within minutes of hooking up the fiber links. Sitting there for about 5 minutes it booted into ROMMON. When this happens, I'm able to boot the sup card back to good status. Previous remedial actions, other than replacing sup cards/chassis, was checking the config register and making sure it was x2102. Previously, it was not, and we corrected and reloaded and it took, we thought this would fix the problem, until today.
[code]....
I'm fairly new to networking and need to migrate an old core to a new core. I have a 6509-e Switch that I had an RMA on one of my 720 sup cards. After receiving the sup card I swapped my slave out with the new one, expecting it to boot into ios. It booted into Roman. I tried to boot the image manually and it did the same thing. I also tried to boot from my flash and, again, booted into ROMmon.
Question: If i configure and change the boot to boot from image it tells me i need to reset or power cycle first. Will this reset the entire switch? As this is production I'd rather not.
I am at home now, but I can supply any logs/hardware model/configs tomorrow. I thought I would see if this is an easy fix.
I have just downloaded new software for sge2010p. I had tried to made an upgrade on some switches, but switches still boot with the old software.I have installed software 3.0.0.18 and boot 2.0.0.03. I have downloaded software 3.0.1 from cisco, put it on tftp and started an upgrade via switch web interface. I have checked that the active image is set to 1, and started the upgrade.Switch has downloaded soft from tftp, and reported that process has been finished without errors.After the restart switch have 3.0.0.18 software again. I have try to do this same on 4 different switches working in L3 and L2 mode - always with the same effect.Should I upgrade both images in the same time to get this work?
I have noticed, that the new firmware is located on image 2.
# show bootvar
Image Filename Version Date Status
----- --------- --------- --------------------- -----------
1 image-1 3.0.0.18 08-Nov-2009 16:21:37 Active
2 image-2 3.0.1.0 19-May-2011 13:05:53 Not active*
[Code] ...
So I try to set active image via console command:
# boot system image-2
and again...
a# show bootvar
Image Filename Version Date Status
----- --------- --------- --------------------- -----------
1 image-1 3.0.0.18 08-Nov-2009 16:21:37 Active*
2 image-2 3.0.1.0 19-May-2011 13:05:53 Not active
"*" designates that the image was selected for the next boot
Finally i have tried to set the active image to "2" using console menu: I have set it like this:
Active Image
============
Unit ID Active Image Active Image after Reset
======= ============ ========================
1 Image 1 Image 2
and save..
[Code]
Where is the right place to set active image for 2. Is the "active image" settings only sets the firmware image which switch uses or configuration files too?
I m having 2500 series router. when i boot router automatically get into router(boot)> . how to solve?
View 6 Replies View RelatedI have Nexus 5548UP, Version version 5.0(3)N2(2b), with a flat configured network. Customer has put several IP subnets on one Vlan. In one subnet is an Siemens SPS wich connects to a Server. This SPS is not reachable since I send a ping from the N5k, then everything works fine. Sniffering that port no arp requests from the N5k are captured. That hapens with every device (Siemens SPS) in the network. Every other clients and server are working fine and there are no problems.
View 1 Replies View RelatedI am trying to get our DCNM to discover the 5548. When I put my credentials for that appliance. I get this error .Failed Device x.x.x.x OS Version 5.1(3)N1(1) is not supported . The DCNM version we have is 5.2(1)S74.
View 1 Replies View RelatedI have a Nexus 5548 Recently restart itself for no reason I ran the command:
sh system reset-reason
----- reset reason for Supervisor-module 1 (from Supervisor in slot 1) ---
1) At 469203 usecs after Sat May 11 14:02:07 2013
Reason: Reset triggered due to HA policy of Reset
Service: eth_port_sec hap reset
Version: 5.1(3)N1(1a)
sh processes log details
Start type: SRV_OPTION_RESTART_STATELESS (23)
Death reason: SYSMGR_DEATH_REASON_FAILURE_SIGNAL (2)
Last heartbeat 6.09 secs ago
RLIMIT_AS: 189894144
System image name: n5000-uk9.5.1.3.N1.1a.bin
I've been searching in Google/Cisco about the eth_port_sec hap reset and cannot find any reason, just something about the same error but in different technology:
[URL]
CSCub36000 #SNMP polling on eth_port_security objects no longer causes an eth_port_sec hap reset.I just to want to be sure, is the same reason...Or do you know something than can cause it on a Nexus Switch?
We have just purchased and installed the L3 daughter card for our 5548UPs and have also installed the L3 Enterprise Services pkg. The problem is, I cannot enable the EIGRP feature even though we have the Ent Svc lic. After doing a little more research, I see that the Lan Base lic is required to enable the L3 card and many of the L3 features (the card is currently in an "offline" state).
From what I have read on this board, the Lan Base lic is a free license that should be included with the L3 daughter card -- however, Cisco licensing will not issue me that license without a sales order (even though a Nexus engineer said it was included, the licensing group will not issue with an official sales order). Well, our vendor ordered the card and the Ent Svcs lic but for some reason we were never sent a PAK for the LAN Base lic.
using the 55xx as a L3 Distribution switch or even as a Core. By enabling the L3 features does it allow you enabled L3 SVI's for VLAN interfaces or are there interfaces on the daughter card that are used for routing instead?
View 5 Replies View RelatedThe Nexus 5548 is running 5.1.3.N2.1a and has the L3 daughter card (N55-D160L3)I have the EIGRP feature enabled. By the way, when doing a 'sh feature' four EIGRP features show up like this: [code] To create the L3 SVI, I go into config mode and attempt to type 'interface vlan 10'. but this doesn't work. These are the only options under the keyword 'interface':
- ethernet
- loopback
- mgmt
- port-channel
I must be missing something simple but can't seem to see what that is. What do I need to do in order to create an L3 SVI on this 5548?
I want to configure management for some Nexus 5548's?I wanted to manage the switches via an SVI. I have read the following document which gives details about the Management SVI but doesn't answer all questions.[URL]I am not running any layer 3 functionality on the switch, no layer3 license (which it mentions in the above link) Will I still be able to create a management SVI. I know I will need to enable the feature 'interface-vlan' to setup a Management SVI, does that require a license?
View 6 Replies View RelatedI encountered problem while trying to copy file from Nexus 5548 to my ftp server (proteus - 192.168.12.220 - the Nexus switch is able to resolve name proteus correctly to 192.168.12.220). See below the working and not working scenarios. I have serached through Cisco Bug Database but unable to find any related bug associated to this problem. This Nexus is running the following NX-OS version.
n5000-uk9-kickstart.5.1.3.N1.1a.bin
n5000-uk9.5.1.3.N1.1a.bin
Working (without specifying the username and full path)
[Code].....
We have two 5548 switches connected to a pair of 6509 running in VSS mode. I am trying to understand the benefit of having bridge assurance on the uplink ports.
If we have the command spanning-tree port type network enabled we cannot do a non disruptive upgrade. If there is bridge assurance on the uplink it warns you of this. Yet if I do not run bridge assurance on the uplinks I can do a upgrade without any disruption.
Why in god would I enable bridge assurance on this VPC link if I cannot do a non disruptive upgrade?
I need to upgrade the code on our two Nexus 5548's in order to facilitate the installation of a few FEX's, but due to the fact that seemingly all of my port-channels are in the STP DESG forwarding state, an ISSU upgrade is not possible. Everything connected directly to our 5548's are utilizing VPC's, including an HP Blade chassis, and several Netapp devices. If I follow the normal upgrade route, should I experience an outage, or should the secondary switch just continue passing traffic?
View 1 Replies View RelatedI'm trying to setup SNMPv3 on a Nexus 5548. We are using SNMPv3 on 3750's without any issue, but haveing issues getting it setup on the Nexus.I have been using the following link for the setup following it line by line. [URL]The part that I'm having issues with is when I try to enforce SNMP message encryption on a per user basis. When I issue snmp-server user (username) enforcePriv, I get warning: unable to update CLI users database. reason: role does not exist grounp not found.
View 1 Replies View RelatedI am using cisco Nexus5548 and trying to enter a snmp community, but it doesn't accept it. I enter a community name that is less than 32 characters, with symbols, numbers and letters.
View 2 Replies View RelatedI am setting up a new environment with 2 5548's and some 2248TP-1GE Fex's and Im running into an issue. I have the peer link and peer-keepalive link that appear to be good. When I configure the fex and vpc for the fex manually on each switch without pre-provisioning the slot the fex comes online and everything appears to be good. I can see all the ineterfaces when doing a sh int br and the sh fex detail shows all good. When I do the exact same thing but pre-provision the slot the fex stays in an offline state. Ive tried disabling the port(s) connected to the fex while configuring everything then enabling them but same thing. [code]
View 5 Replies View RelatedI have a 2232 dual homed to 2 5548's via a port-channel/ vpc. I have one 5548A and configure the port for the 2232 with a vlan, plug into that port and it doesn't come up (inactive). I go to 5548b (Primary) and configure the port and it comes up.
View 3 Replies View Relatedregarding PVLANs and the Nexus, my understanding is that we cannot configure Private VLANs on a FEX trunk port with a NX-OS release older than 5.1(3)N2(1) for the Nexus5548... Is there any known workaround for this limitation (appart from performing a SW upgrade)?
View 2 Replies View RelatedI am working for an Air Force client and am adding a handful of 5548s into their network. My question is how Tacacs+ is configured. My hands are tied in regards to testing in an operational environment so I want to ensure the configs are correct prior to deployment/maintenance window and avoid any remote issues.
I have read the "Cisco Press - TACACS+" config guide and it was somewhat vague in regards to operational deployment.
My basic NX-OS configs are as follows:
- feature tacacs+- tacacs-server key 7 "002A52xxxxxxxxxxxxxxxx8"- tacacs-server host 128.xx.xx.xx timeout 10- tacacs-server host 128.xx.xx.xx timeout 10- tacacs-server directed-request
When I try to set the following command string, aaa authentication login default group tacacs+ local, the NX-OS asks me the input a "server group name". There are no server groups configured. Do I need them? Can I get by without configuring a group name because the client probably will not.
The Cisco IOS devices are configured with normal aaa authentication/authorization parameters. Also, do the VTY ports default to sshv2 and the correct tacacs+ parameters with the "transport input ssh" command (not available)?
I am trying to install SFP-GE-T module on Nexus 5548UP Switch, but is giving the ‘SFP validation Failed’ error. The details of the switch is given below
Model : N5K-C5548UP-FA
The interface is configured with speed 1000 before inserting the module, still we are getting the same error. PFA logs for more details We have 8 Nos of SFP-GE-T modules , all are giving same error. We tried to insert the module on onboard as well as expansion module.
The same module is working fine on Cisco 3750X-24T-L Switch As per the Hardware installation guide , SFP-GE-T transciever is supported on N5K platform. Please extend your support in configuring SFP-GE-T module on N5K platform? We tried with SFP-GE-S module on the same switch , and the same is found working fine.
We have successfully peered two 5548UP switches together and separately we have successfully peered two 5596UP switches together. Works great and is our standard going forward for data center switching. I've been casting about Google and Cisco looking for an answer to this question:
Is it possible to have more than two 5500 class Nexus switches participate in a peered vPC configuration? For instance, can I connect a single FEX to four 5500 class switches in a vPC configuration? The question is more academic than actionable. Even if the answer is yes we probably wouldn't be in a position to implement something like this for a while.
I am trying to interconnect a pair of Nexus 5548 at adjacent sites, using 2 2960-S switches at each site, the reason being that the Multimode Fiber between the sites will only support 100mb and I need this up while I finish having SMF laid.
I have attached a diagram, just debating whether to use etherchannel or vPC - would like to hear some opinions...
Assume the interconnect between the 5548's needs to be 802.1q trunk