Cisco WAN :: 2610 / Windows 7 Can't Ping Past Local Interface
Jul 18, 2012
Ive got my home lab setup with two 2610 routers hooked togeather with a DTE/DCE Crossover and I have OSPF configured on both routers. Each router has one 3550 switch connected to each FA0/0 inteface. The issue is that Everything can be pinged except my windows 7 PC connected to the R1 LAN. Everything else can be pinged from any other device. I checked the PC gateway configuration, disabled the firewall and checked my switch configuration! Is their something that I need to change in Windows?
Windows PC ------------ 3550 Switch-------------R1-----------------------------------R2---------------------3550 Switch----------------------Linux Box
Windows PC can't ping past the FA0/0 interface between the switch and R1
View 7 Replies
ADVERTISEMENT
Nov 12, 2011
while trying to hookup wireless cant det past gateway ping on test. Iv'e used addresses given to me by net gear.
View 5 Replies
View Related
Oct 24, 2012
I've spent the last two days working on this problem and it is killing me! I know the answer has to be something simple, but despite hours of searching and trying different things, I just can't seem to fix it.Essentially, I am going to be installing a Cisco 2691 and use it as the default gateway for a small business. It will be directly connected to a cable modem with a static IP. The other Ethernet interface is going to connect to a 2950 switch with a couple different VLANs.
The problem I'm having is that I can ping anything external from the router itself. From the clients connected to the 2950, I can ping IPs in other VLANs, and I can ping up to the IP of the external interface, but no pings go beyond that.I've set up NAT overload on the router, and when I do a debug ip nat, I see the pings trying to get through with the proper translations, but I still don't receive ICMP replies back.I set up GNS3 to simulate what I'm trying to accomplish (since it emulates a 2691). Attached is a jpg of the topology -- on the right is the "simulated ISP" with 3 loopback networks and one host on a different subnet. The 2691 has a static route to the "Internet" router, and can ping everything attached to the router, including the host. The host (5.5.5.5) can also ping the outside interface of the 2691 (50.50.50.2).
However, the hosts behind the 2691 can't ping past 50.50.50.2. The 192.168.0.x network can be ignored, because that network won't need to access the Internet. But the 10.10.20.x (VLAN 20) and 10.10.30.x (VLAN 30) networks will need to. In the simulation, the hosts are 10.10.20.5 and 30.5. They can ping each other, their default gateways, and the 2691 outside interface (50.50.50.2) but not the other side, the "Internet" router at 50.50.50.1 or beyond.
[code]....
View 4 Replies
View Related
Jan 9, 2012
The VPN will connect.I can ping and connect to the ASA 5510 on it's LAN interface.My problem is that I cannot ping or access anything on the LAN past the firewall. What am I doing wrong?
Here is my config.Result of the command: "show config"
Saved
: Written by enable_15 at 22:55:02.299 UTC Tue Jan 10 2012
!
ASA Version 8.2(5)
!
hostname ********
[code]....
View 1 Replies
View Related
Mar 31, 2012
I have a new 3560G to set up a small network for a remote site. I configured the vlan and an SVI as the gateway. The switch is also the DHCP server for the LAN. I configured Gi0/2 as L3 port, connecting to the nearest neighbor. My network runs EIGRP so i advertised the routes into the EIGRP process. The switch forms EIGRP neighbors and learns all routes in the enterprise network. The problems I'm having now are: 1. The switch learns all routes in my enterprise LAN and can ping devices in the enterprise LAN, but I can’t ping any interface on the switch from the enterprise LAN. 2.
View 5 Replies
View Related
May 1, 2012
I have a Cisco ASA 5505 and I have my internal and external interfaces configured but I currently cannot ping from the inside to an IP Address on the outside. I had this setup and working and I have another set of equirement that I am replacing that is working with my service provider so I know it is a configuration issue. When I ping 4.2.2.2 for example I get:
Destination host unreachable
Do I need to add a static route from my inside interface to my outside interfaces?
: Saved
:
ASA Version 8.2(5)
!
hostname pxasa
[Code].....
View 2 Replies
View Related
Aug 15, 2011
When I ping an address from my windows machine, it succeeds, but when I ping to the same IP on my MAC OS X machine, it fails.
1. Why?
2. How to get successful ping on my MAC machine?
View 1 Replies
View Related
Apr 23, 2011
i have configured remote access vpn on my 2801 router's gio0/0 int ip x.x.x.1. i connected my laptop through vpn client from internet. i connected successfully and my vpn router gives me the assigned ip block y.y.y.1. from my laptop i can ping the other int gio/1 ip z.z.z.1 but i cant ping the ip z.z.z.2 of my core sw which is connected on router's int gi0/1.
View 14 Replies
View Related
Jan 4, 2011
I have a cisco router 2811 connected on other two routers but can't ping any of them from any of them too (frame-relay encap correct) DLCI mapping ok all ip configured only router 2 's line protocol is up the rest is down on others and seems LMI sent are not receive and do know how correct that
View 1 Replies
View Related
May 21, 2011
I just installed a new ASA 5505 for an office with three internal subnets.* The three networks can each get online fine and ping eachother, but cannot browse to shares on the two internal networks other than their own.* How do I configure the ASA to allow all traffic between these three inside networks?
192.168.152.0
192.168.152.0
192.168.154.0
[code]....
View 8 Replies
View Related
Apr 3, 2013
I'm using 3 AP's 1140 with local authentication using local radius (flex connect mode).the radius server im using is MS 2008 R2.authentication is working great on all devices pc's&mobile.authentication method is PEAP wpa2 aes enterprise.after 3 or 4 hours devices loose connectivity to the web.the device seems to be still connected to the ap but there is no ping to host from local lan or any arp learnd on local router.only manual disconnect on device and reconnecting brings connectivity up again.in one case only reseting the AP's worked.
View 6 Replies
View Related
Nov 27, 2012
I cannot ping mydomain.local from any computer on my network. In order to this, I have to set DNS 1 as my server's ip address, then I can ping it. The reason this is a problem is because in order to add a workstation to my domain, I have to manually configure DNS to my server's ip. I have two networks, all new systems and this occurs on both. So obviously it is the way im setting things up[CODE]
View 13 Replies
View Related
Jan 18, 2013
I am trying to connect my 2800 Series CIsco Office router with VPN client software from home. I can successfully authenticate and get the IP address from the pool configured but couldnt ping any LAN Ips including default gateway. I am pasting my router's configuration.
IP Address Of LAN: 192.168.22.x/ 24
IP Addresses handed out to Clients: 10.10.10.5- 10.10.10.20
aaa new-model
!
!
aaa authentication login default local
[code]....
I have noticed that my virtual-access interface comes up but the line protocol of virtual-interface remains down as follows:
Virtual-Template100 x.x.x.x YES TFTP up down
Also The client PC picks up a random gateway of 10.10.10.1 which I never configured anywhere on the server.
View 26 Replies
View Related
Jul 24, 2012
I have, what I believe to be, a simple issue - I must be missing something. Site to Site VPN with Cisco ASA's. VPN is up, and remote hosts can ping the inside int of ASA (10.51.253.209). There is a PC (10.51.253.210) plugged into e0/1.
I know the PC is configured correctly with Windows firewall tuned off. The PC cannot get to the ouside world, and the ASA cannot ping 10.51.253.210.
I have seen this before, and I deleted VLAN 1, recreated it, and I could ping the local host without issue. Basically, the VPN is up and running but PC 10.51.253.210 cannot get out
ASA Version 7.2(4)
!
hostname *****
domain-name *****
enable password N7FecZuSHJlVZC2P encrypted
[Code]...
View 2 Replies
View Related
Dec 2, 2012
I have a scenario where there is an ASA5510 configured as follows:
Interface0 = Outside
Interface1 = LAN
Interface2 = DMZ
Interface3 = unused
Running ASA version 8.2[1]
All network operations are fine, as are the IPSEC tunnels to other branch offices, and the incoming SSL VPN accessed via the IP address assigned to the external adapter.
My problem is that I have a device on the DMZ that needs to access the AnyConnect service hosted on the external adapter so that it can access LAN resources. When I try accessing it, I see the following errors appearing in the debug log:
3Dec 03 201212:10:50710003[DMZ client address]51031[AnyConnect ExternalAddress]443TCP access denied by ACL from [DMZ client address]/51031 to DMZ:[AnyConnect ExternalAddress]/443 If you look closely, it suggests an ACL issue from the DMZ client to the external AnyConnect IP address BUT it suggests the Anyconnect IP address is on the DMZ interface.
View 1 Replies
View Related
Feb 7, 2013
I wounder if there is any way to ping the local deviceses connected to a network hosted by a Cisco 1921 router? I wan't to be able to ping the device(computer name) but currently cant do that.
View 1 Replies
View Related
Dec 11, 2010
I've configured a lot vpn server for 857/1800, etc. But this has never happened.I configured 881 as VPN server using CP.Shared key, local group and local user authetication with split route.Local pool 192.168.100.1-254? I have acl for telnet which allows local pool IPs.I have acl to deny local network to local pool IPs for NAT.I've deleted the whole settings and re-run the wizard. It's still the same thing. I can connect from the VPN Client, but no traffic going through. The problem to me is isakmp with DPD. But why it is dead? Why no response from the server? If it is an error, why connection has no problem.
View 1 Replies
View Related
May 12, 2013
I have a cisco ASR 1002 I have plugged a host into an addressed port and the port comes up however the host cannot ping the router and the router cannot ping the host. Neither can router ping its self. I do the same on a cisco 2800 router and it works fine. What's goin on. Is it the fact that this is a ASR router ?
View 5 Replies
View Related
May 27, 2012
I have configured eigrp routing on cisco 1941 ISR with two interfaces advertised. However i can not ping the router interface on g 0/0 but can ping the device and computers attached to that network. When i ping from the same network i'm able to ping the interface but not from anyway else. i can also ping the other devices on other network from g 0/0 attached hosts. How can i enable ping to this interface so that i start monitoring the network?
Below i have attached the network configurations for the router;
!boot-start-markerboot-end-marker!!enable secret 5 xxxxxxxxxxx!no aaa new-model!no ipv6 cefip source-routeip cef!!!!!multilink bundle-name authenticated!crypto pki token default removal timeout 0!!license udi pid
[Code].....
View 3 Replies
View Related
Jan 14, 2013
I have lots of 857's routers in the field with mostly the latest OS - 12.4(15)T17 making ezVPN connections to a 2951 with 15.1(4)M5.All the 857's have lookback and vlan interfaces similar to :
interface Loopback0
ip address 50.43.8.1 255.255.255.255
ip tcp adjust-mss 1452
end
[code]....
Now lately for some or other reason we have instances where I can ping either the VLAN or the LOOPBACK interface, but not both. Or I have instances where the 2951 can ping all the interfaces on the 857, but the 857 can not ping the 2951. Or I have instances where the 2951 can not ping the 857, but the 857 can ping the 2951.The way I have been fixing this is either to add crypto ipsec client ezvpn SMS_VPN inside to the loopback interface, or if it is there already to remove it. This usually works for a few days, but then suddenly I have to reverse this again. If that does not work then I usually do lots of clear crypt sess and/or clear crypt ipsec client ezvpn on the 857, or clear crypt sess remote 857_ip_address from the 2951 and then suddenly it starts working again.
View 1 Replies
View Related
Sep 19, 2012
I have recently installed an ASA5510 at a site in South Africa to connect via VPN to a site in the UK (ASA5520). The VPN comes up fine with the 5520 in the UK, however, I can not connect to the inside interface over the VPN, but can access it from the internal LAN. All other hosts on the LAN are accessible over the VPN.
The 5510 also has another VPN to another site in SA and the 2nd site cannot ping the interface either.
View 10 Replies
View Related
Feb 3, 2013
I cannot seem to ping from the outside of my 5520 firewall to an inside network. I have a single physical outside interface connected to a Layer 2 switch, with a laptop connected to it. This is on network 10.11.131.0/28. From there, I cannot ping to the inside interface (which is a sub interface on G0/0) with network 10.11.130.0/24/ For some reason, it doesnt work.
Now. I had access-lists in place, but have removed them for testing and it still doesnt work. I have set the security level of inside and outside to 100, and entered the same-security-traffic permit inter-interface command - still no joy. Below is the relevant configuration.
Inside Interface
interface GigabitEthernet0/0.96
description L3 Interface - Informational Zone
vlan 96
[Code].....
View 4 Replies
View Related
Mar 19, 2013
I've had some issues with my 892 router. [code] When match address is set to acl-net12, I can't ping my router on external interface and tunnel is working very bad (15%-20% packet loss).If I change match address from acl-net12 to acl-net12-new then I can ping my router on external interface and vpn si working fine.
I have also an acl (set on external interface) which allow ping but it seems that is not working when acl-net12 is used on crypto map. [code]
View 6 Replies
View Related
Nov 14, 2011
I have a Cisco ASA 5505, the problem is I am not able to ping to outside natted interface (ip: 172.88.188.123 and 124 and 125) from inside network I have looked for ASA documentation through the internet and still got nothing.
the config are:
: Saved
:
ASA Version 8.2(1)
!
[Code].....
View 2 Replies
View Related
Feb 7, 2012
I have one problem doing a ping to a router lan interface, I have 3 routers (2801) connected between each other (separated 1 mile each), the link is established trough microwave signals (connected to the 2801 fast ethernet interfaces), every router has a connection to a LAN. One of them is located at headquarters.Last thursday I replace one of the router with a cisco 2901, i configure the router with the same configuration that was on the 2801, i power up the router and the 2 link were up without problems.One day after the noc called me to tell me that after i replace the router they can't ping the router IP lan interface on the new 2901 (before the replacement the ping was sucessful). I called one user the lan connected to that 2901, and they can do a ping to the router's LAN IP address.
I can ping the 2901 IP wan interfaces, I can ping the LAN users ip address, but i cannot ping the router LAN IP address, from my desktop, and neither the 2 routers 2801 connected to the 2901.I show the configuration on the 2901, I couldn't change it because i didn't have time to do that, but i'll change the configuration to use ipsec tunnels.The configuration as you can see, has a crypto map, but the acl used by the crypto map, only permits the interfaces ip address, so i think that doesn't work, so the traffic doesn't get encrypted, but i don't know if that is the problem why i can't do a ping to the lan interface. [code]
View 5 Replies
View Related
Aug 9, 2012
I'm trying to set up a Guest VLAN for wireless at a client site, and I feel like I'm missing something small in the configuration, since I can't ping any of the VLAN interfaces from my laptop when the address is statically set to something in the 172.20.100.x range.
I've pasted the configs for the ASA 5505 and the 6 switches below for convenience. Near as I can tell, all should be well. The ports are in trunking mode, the "show cdp neighbors" command returns the proper information, VLAN 100 exists on all the switches, etc.
Code:
ASA Version 7.2(4)
!
hostname ASA
domain-name xxxx.local
enable password Cj3LF.ehxXN3xVkxWcxd encrypted
passwd Cj3LF.ehxXN3xVkWcxd encrypted
[Code] ......
View 17 Replies
View Related
Feb 9, 2011
I need to get past a Cisco firewall my roomate set up on our internet. I have zero access to the internet, and cannot access a website like Vtunnel to get around it.
View 2 Replies
View Related
May 10, 2011
I have a new ASA 5505 and all is working fine, I can CLI and ASDM into it, but just can't ping the inside interface, do I need to enable a feature to make this work somehow?
View 1 Replies
View Related
Oct 22, 2012
I have been working on figuring out a VPN problem on my companies ASA5510. I was accessing the device via: ASDM, SSH using Putty, and even initially with a console cable (also using Putty) using a computer in the networking closet. All 3 of these access methods worked properly for me.I believe I may have inadvertently changed something as of Friday using ASDM. I am mostly assuming this because, as of yesterday I can no longer connect to the device. I actually cannot even communicate with it (ping the interface I normally use to manage, which I could previously ping). No computer on the same subnet as me is able to ping the interface. The device is still accepting VPN connections, dishing out DHCP addresses and everything else it normally does, but I really need to be able to gain access to it again. I am thinking to reboot the device when there is some downtime, in the hopes that ASDM doesn't save to startup-config and only to running-config.
View 5 Replies
View Related
Aug 4, 2011
I'm currently configuring an ASA5510.I connected a laptop (IP 192.168.96.18/255.255.255.0) to port 0/2 and tried to ping 192.168.100.2 ... impossible to ping outside interface.I resetted the config of the ASA to retest more simple. [code]
View 1 Replies
View Related
Apr 13, 2013
I ran into a very strange icmp ping issue. The network has been working fine other than the issue listed below, L2L VPN works fine and all three data centers can access each other via L2L VPN.I have three ASA5510. [code]
View 5 Replies
View Related
Feb 24, 2013
What would cause an interface to show up/up (looped), but you still can't ping that loop?...It is on a Cisco 7613 with an Enhanced FlexWan (WS-X6582- 2PA), with a Mx Serial PA, 8 ports (73-1580-10) and running IOS ver 12.2(33)SRE2 [code]
View 5 Replies
View Related
Dec 12, 2011
I have an ASA 5505 that I'm trying to set up a guest network on. I've configured an interface as a trunk and allowed the 2 vlans but I'm not getting any layer 3 to it. The switch connected to it is a 3560 and port is configured as a trunk with the same vlans.
I can't ping the ASA inside interface but I see its MAC address in the swtich's table.
[code]....
View 4 Replies
View Related
